Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “forcing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74

Experimental study of unsteady hydrodynamic force matrices on whirling centrifugal pump impellers

An experimental facility was constructed and instrumented. A set of centrifugal flow pumps whose impellers were made to follow a controlled circular whirl motion were studied. The aim was to characterize the steady and unsteady fluid forces measured on the impeller under various pump operating conditions. The postulation was that the unsteady lateral forces result from interactions between the impeller and the surrounding diffuser and/or volute (via the working fluid), and that under certain flow regimes these forces can drive unstable lateral motions of the pump rotor. The lateral hydrodynamic forces were decomposed into their steady and unsteady parts, the latter being further expressed in terms of a generalized fluid stiffness matrix. Conclusions regarding the effect of impeller geometry could not be reached given the similarity of the tested designs. However, other results on phenomena such as skin friction and leakage flow are presented. Some of the findings are compared to experimental and theoretical data from other sources. Finally, the rotordynamic consequences of the results are discussed as the present data were applied to the case of the Space Shuttle Main Engine (SSME) High Pressure Oxidizer Turbopump (HPOTP).

Belgacem, Jery↗

Calculation of forces on magnetized bodies using COSMIC NASTRAN

The methods described may be used with a high degree of confidence for calculations of magnetic traction forces normal to a surface. In this circumstance all models agree, and test cases have resulted in theoretically correct results. It is shown that the tangential forces are in practice negligible. The surface pole method is preferable to the virtual work method because of the necessity for more than one NASTRAN run in the latter case, and because distributed forces are obtained. The derivation of local forces from the Maxwell stress method involves an undesirable degree of manipulation of the problem and produces a result in contradiction of the surface pole method.

Sheerer, John↗

Forebody and missile side forces and the time analogy

A review of the 2-D, impulsively started cylinder literature is given to identify a number of physical parameters that can impact the nondimensional time at which vortex asymmetries begin. These parameters are then related to 3-D testing and explain the lack of data repeatability. The implications of these parameters on 3-D computational modeling is also discussed. An ad hoc form of the time analogy is then used to analyze and organize a slender body data base. An important result of the analysis is that the sectional side force in the nose region is a key to understanding the side force behavior for the configuration as a whole. The nose side force at the first pressure station is shown, for the data analyzed, to uniquely determine the rest of the side force development for laminar flow and to correlate with roll orientation independent of angle of attack and Reynolds number.

Hall, Robert M.↗

Distribution of resistive body-force in curved free-surface flow

The customary procedure for including resistive effects in turbulent hydraulic and stratified atmospheric flows is to integrate the empirically-known boundary shears over the entire wetted boundary of a thin fluid slab. A resistive body-force is then assumed to exist everywhere in each slab to replace the boundary shearing force. For the classical Saint-Venant (1871) model, this body-force can be shown to have a constant distribution in the vertical direction, and therefore can be evaluated for use in the momentum differential equation. In the newer Dressler theory (1978), however, for unsteady flow over curved beds, it is proved here that a constant body-force distribution is not possible. Its variable distribution is determined as well as its magnitude for use in the curved-flow equations. This variable distribution acts to produce an equal resultant in every thin layer of fluid parallel to the bed in an angular wedge over the curved channel bed. The new curved-flow equations are therefore extended to include resistive effects.

Sivakumaran, N. S.↗

Multiple-mode nonlinear free and forced vibrations of beams using finite element method

Effects of large deflection geometric nonlinearity and multiple modes for free and forced vibrations of beams are investigated. Inplane displacement and inplane inertia are included in the formulation. The finite element method is employed. A harmonic force matrix is derived for forced vibration analysis. The relations of amplitude, frequency ratio and forcing intensity for beams of different boundary conditions and various load conditions are presented.

Mei, Chuh↗

Effects of forced and free convections on structural temperatures of Space Shuttle Orbiter during reentry flight

Structural performance and resizing (SPAR) finite-element thermal analysis computer program was used in the heat transfer analysis of the Space Shuttle Orbiter wing subjected to reentry aerodynamic heating. With sufficient external forced convective cooling near the end of the heating cycle, the calculated surface temperatures of the thermal protection system (TPS) agree favorably with the flight data for the entire flight profile. However, the effects of this external forced convective cooling on the structural temperatures were found to be negligible. Both free convection and forced convection elements were introduced to model the internal convection effect of the cool air entering the Shuttle interior. The introduction of the internal free convection effect decreased the calculated wing lower skin temperatures by 20 F at most, 1200 sec after touchdown. If the internal convection is treated as forced convection, the calculated wing lower skin temperatures after touchdown can be reduced to match the flight-measured data very closely. By reducing the TPS thicknesses to certain effective thickness to account for the TPs gap heating, the calculated wing lower skin temperatures prior to touchdown can be raised to agree with the flight data perfectly.

Ko, William L.↗

On the glitches in the force transmitted by an electrodynamic exciter to a structure

Around resonance, the force transmitted by an exciter into a structure will be smaller or greater than a reference force generated by its coils due to electromechanical interaction. A simple analysis is presented which reveals how this phenomenon of force drop-off is controlled by three factors. The first factor, called Armature Mass Factor, describes a purely mechanical interaction between the structure and the exciter. The electromechanical energy conversion and its interaction with the structure yields two additional factors, called Electrical Resistance and Electrical Inductance Factors. They describe the effects of coil resistance, inductance and magnetic field strength relative to structural damping and stiffness. Present analysis indicates that, under proper circumstances, more than 90 percent of the force drop-off can be eliminated if armature-to-structure mass ratio is smaller or equal to half of modal loss factor.

Rao, Dantam K.↗

Aeroelastic forced response analysis of turbomachinery

An introduction is given to the research activity that is underway to enable the prediction of turbomachinery aeroelastic forced response. An effort is being made to assemble a computer program (FREPS) which incorporates the aeroelastic structural models, unsteady aerodynamic models, and forcing function models. The structural and aerodynamic models are currently well developed. The forcing function models are at a primitive level. A significant activity has begun to identify the forcing functions due to stator-rotor aerodynamic interaction.

Smith, Todd E.↗

The influence of gravitoinertial force level on oculomotor and perceptual responses to Coriolis, cross-coupling stimulation

The goal of the present experiment was to determine whether gravitoinertial force magnitude influences oculomotor and perceptual responses to Coriolis cross-coupling stimulation. Blindfolded subjects who were rotating at constant velocity were asked to make standardized head movements during the free-fall and high-force phases of parabolic flight, and the characteristics of their horizontal nystagmus and the magnitude of their experienced self-motion were measured. Both responses were less intense in the free-fall periods than in the high-force periods. These findings suggest that the response to semicircular canal stimulation depends on the background level of gravitoinertial force.

Dizio, Paul↗

Boundary force method for analyzing two-dimensional cracked plates

The Boundary Force Method (BFM) was formulated for the two-dimensional stress analysis of complex crack configurations. In this method, only the boundaries of the region of interest are modeled. The boundaries are divided into a finite number of straight-line segments, and at the center of each segment, concentrated forces and a moment are applied. This set of unknown forces and moments is calculated to satisfy the prescribed boundary conditions of the problem. The elasticity solution for the stress distribution due to concentrated forces and a moment applied at an arbitrary point in a cracked infinite plate are used as the fundamental solution. Thus, the crack need not be modeled as part of the boundary. The formulation of the BFM is described and the accuracy of the method is established by analyzing several crack configurations for which accepted stress-intensity factor solutions are known. The crack configurations investigated include mode I and mixed mode (mode I and II) problems. The results obtained are, in general, within + or - 0.5 percent of accurate numerical solutions. The versatility of the method is demonstrated through the analysis of complex crack configurations for which limited or no solutions are known.

Tan, Paul W.↗

Adaptive Force And Position Control For Robots

Control system causes end effector of robot manipulator to follow prescribed trajectory and applies desired force or torque to object manipulating or in contact. Characterized by hybrid control architecture, where positions and orientations along unconstrained coordinate axes controlled by position-control subsystem, while forces and torques along constrained coordinate axes controlled by force-control subsystem. Compensates for dynamic cross-coupling between force-and position-control loops and does not require knowledge of complicated model of dynamics of manipulator and environment.

Seraji, Homayoun↗

Free-molecule-flow force and moment coefficients of the aeroassist flight experiment vehicle

Calculated results for the aerodynamic coefficients over the range of + or - 90 deg in both pitch and yaw attitude angles for the Aeroassist Flight Experiment (AFE) vehicle in free molecule flow are presented. The AFE body is described by a large number of small flat plate surface elements whose orientations are established in a wind axes coordinate system through the pitch and yaw attitude angles. Lift force, drag force, and three components of aerodynamic moment about a specified point are computed for each element. The elemental forces and moments are integrated over the entire body, and total force and moment coefficients are computed. The coefficients are calculated for the two limiting gas-surface molecular collision conditions, namely, specular and diffuse, which assume zero and full thermal accommodation of the incoming gas molecules with the surface, respectively. The individual contribution of the shear stress and pressure terms are calculated and also presented.

Blanchard, Robert C.↗

Robot arm force control through system linearization by nonlinear feedback

Based on a differential geometric feedback linearization technique for nonlinear time-varying systems, a dynamic force control method for robot arms is developed. It uses active force-moment measurements at the robot wrist. The controller design fully incorporate the robot-arm dynamics and is so general that it can be reduced to pure position control, hybrid position/force control, pure force control. The controller design is independent of the tasks to be performed. Computer simulations show that the controller improves the position error by a factor of ten in cases in which position errors generate force measurements. A theorem on linearization of time-varying system is also presented.

Tarn, T. J.↗

The influence of centrifugal forces on the B field structure of an axially symmetric equilibrium magnetosphere

A model is presented of an axially symmetric pole-on magnetosphere in MHD force balance, in which both plasma thermal pressure gradients and centrifugal force are taken into account. Assuming that planetary rotation leads to differentially rotating magnetotail field lines, the deformation of magnetotail field lines under the influence of both thermal plasma pressure and centrifugal forces was calculated. Analytic solutions to the Grad-Shafranov equation are presented, which include the centrifugal force term. It is shown that the nonrotational magnetosphere with hot thermal plasma leads to a field configuration without a toroidal B(phi) component and without field-aligned Birkeland currents. The other extreme, a rapidly rotating magnetosphere with cold plasma, leads to a configuration in which plasma must be confined within a thin disk in a plane where the radial magnetic field component B(r) vanishes locally.

Ye, Gang↗

Observations of wind-forced deep ocean currents in the North Pacific

The role of the quasi-steady Sverdrup balance in the midlatitude atmospheric response in the North Pacific was investigated by examining 200 instrument-years of moored current measurements in the deep ocean across the breadth of the midlatitude North Pacific. These data provide evidence of a seasonal modulation in the ocean eddy kinetic energy beneath the thermocline at several locations north of 35 deg N, which was often found to be in phase with the local atmospheric forcing function. Results of the measurements indicate that, throughout the midlatitude North Pacific, topography plays a crucial role in the wind forced response; the bottom slope tends to enhance the beta effect in this basin. Topography narrows the available bandwidth for forced barotropic Rossby waves, facilitating a quasi-steady topographic Sverdrup response over most of the basin. However, the enhanced beta effect reduces the magnitude of the ocean's response to wind forcing.

Koblinsky, C. J.↗

Force user's manual: A portable, parallel FORTRAN

The use of Force, a parallel, portable FORTRAN on shared memory parallel computers is described. Force simplifies writing code for parallel computers and, once the parallel code is written, it is easily ported to computers on which Force is installed. Although Force is nearly the same for all computers, specific details are included for the Cray-2, Cray-YMP, Convex 220, Flex/32, Encore, Sequent, Alliant computers on which it is installed.

Jordan, Harry F.↗

Architectural study of the design and operation of advanced force feedback manual controllers

A teleoperator system consists of a manual controller, control hardware/software, and a remote manipulator. It was employed in either hazardous or unstructured, and/or remote environments. In teleoperation, the main-in-the-loop is the central concept that brings human intelligence to the teleoperator system. When teleoperation involves contact with an uncertain environment, providing the feeling of telepresence to the human operator is one of desired characteristics of the teleoperator system. Unfortunately, most available manual controllers in bilateral or force-reflecting teleoperator systems can be characterized by their bulky size, high costs, or lack of smoothness and transparency, and elementary architectures. To investigate other alternatives, a force-reflecting, 3 degree of freedom (dof) spherical manual controller is designed, analyzed, and implemented as a test bed demonstration in this research effort. To achieve an improved level of design to meet criteria such as compactness, portability, and a somewhat enhanced force-reflecting capability, the demonstration manual controller employs high gear-ratio reducers. To reduce the effects of the inertia and friction on the system, various force control strategies are applied and their performance investigated. The spherical manual controller uses a parallel geometry to minimize inertial and gravitational effects on its primary task of transparent information transfer. As an alternative to the spherical 3-dof manual controller, a new conceptual (or parallel) spherical 3-dof module is introduced with a full kinematic analysis. Also, the resulting kinematic properties are compared to those of other typical spherical 3-dof systems. The conceptual design of a parallel 6-dof manual controller and its kinematic analysis is presented. This 6-dof manual controller is similar to the Stewart Platform with the actuators located on the base to minimize the dynamic effects. Finally, a combination of the new 3-dof and 6-dof concepts is presented as a feasible test-bed for enhanced performance in a 9-dof system.

Tesar, Delbert↗

Integrated force method versus displacement method for finite element analysis

A novel formulation termed the integrated force method (IFM) has been developed in recent years for analyzing structures. In this method all the internal forces are taken as independent variables, and the system equilibrium equations (EE's) are integrated with the global compatibility conditions (CC's) to form the governing set of equations. In IFM the CC's are obtained from the strain formulation of St. Venant, and no choices of redundant load systems have to be made, in constrast to the standard force method (SFM). This property of IFM allows the generation of the governing equation to be automated straightforwardly, as it is in the popular stiffness method (SM). In this report IFM and SM are compared relative to the structure of their respective equations, their conditioning, required solution methods, overall computational requirements, and convergence properties as these factors influence the accuracy of the results. Overall, this new version of the force method produces more accurate results than the stiffness method for comparable computational cost.

Patnaik, Surya N.↗