Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “drops”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Film boiling of mercury droplets

Vaporization times of mercury droplets in Leidenfrost film boiling on a flat horizontal plate are measured in an air atmosphere. Extreme care was used to prevent large amplitude droplet vibrations and surface wetting; therefore, these data can be compared to film boiling theory. For these data, diffusion from the upper surface of the drop is a dominant mode of mass transfer from the drop. A closed-form analytical film boiling theory is developed to account for the diffusive evaporation. Reasonable agreement between data and theory is seen.

Baumeister, K. J.↗
NASA NTRS1975

Cardiorespiratory responses to orthostasis and the effects of propranolol

Cardiac output and gas exchange were determined serially using the single-breath method of Kim et al. before, during, and after orthostasis on six subjects after beta-adrenergic blockage and in duplicate controls. In the latter, heart rate increased and pulse pressure dropped immediately on tilting to 60 deg and remained stable while cardiac output and stroke volume declined gradually over 21 min upright. On propranolol, heart rate was 10 bpm lower supine and 20 bpm less at 60 deg but cardiac output was only slightly lower before and following tilt-up. However, after 15 min upright, stroke volume and cardiac output recovered on propranolol exceeding the controls after 21 min without change in heart rate. Returning to supine, heart rate dropped in all tests with a transitory increase in stroke volume, cardiac output and arteriovenous O2 difference. At the same time, apparent O2 uptake increased temporarily, reflecting the return of pooled venous blood to the lungs. Orthostatic tolerance did not appear to be affected by beta-adrenergic blockade.

Loeppky, J. A.↗
NASA NTRS1975

Skylab fluid mechanics demostration - A study of water droplet oscillations in space

In the Skylab experiment a drop of water was caused to oscillate at its natural oscillation frequency. The drop was observed until its oscillation began to decay due to its internal damping. A determination of the change in amplitude with time made it possible to verify the applicability of a theoretical model. The fundamental concept of the model is that fluid surfaces tend to an equilibrium shape produced by the balance of the forces of fluid pressure and surface tension. The theoretical model is based on the assumption that the wave amplitude is small compared with the wavelength.

Vaughan, O. H.↗
NASA NTRS1975

Practical aspects of plasma processes in thermionic energy converters

Over a decade of cesium vapor thermionic converter research has yielded sufficient understanding of the basic plasma processes to permit application of this understanding to improvement of converter performance. A performance index is defined which relates such converter improvements directly to increases in system performance. A prime practical objective of current research is to reduce or eliminate the arc potential drop presently required to sustain the plasma in the ignited cesium diode. This will substantially increase the energy conversion efficiency, and will permit operation at substantially lower emitter temperatures without requiring lower collector (heat rejection) temperature. Present work is concentrating on evaluating and reducing to practice the several methods employing auxiliary ion sources to eliminate the arc drop which were demonstrated over a decade ago: i.e., various ignited and unignited triode concepts, and the pulse-enhanced diode and triode. These methods are reviewed in light of present understanding and recent experimental data.

Rasor, N. S.↗
NASA NTRS1975

Research on metal solidification in zero-g state

The containerless solidification of several pure metals and metallic alloys was studied in a low gravity environment. The tests were performed in the MSFC 4.2 s drop tower using a rapid wire melting apparatus designed and built for this purpose. Pure iron and nickel, and alloys of iron-nickel, iron-carbon, nickel-aluminum and tungsten-rhenium were all melted and solidified at a gravity level of approximately 100.000/-4 g. Interpretation of the results has led to an appreciation of the factors controlling the successful execution of this drop test experiment and to a delineation of the limits of applicability of the apparatus. Preliminary metallurgical evaluations are presented of the overall shapes, lattice parameters, surface microstructure,, cross-sectional microstructures, solidification and transformation sequences, evaporative segregation, and localized solute redistribution observed in the low-gravity specimens. The effects of low gravity on metallic solidification are discussed with particular emphasis on observations of spontaneous undercooling and evaporative segregation in uncontained melts.

Papazian, J. M.↗
NASA NTRS1975

Vapor-modulated heat pipe report. Flight data analysis and further development of variable-conductance heat pipes

The design and testing of a heat pipe for spacecraft application is presented. The application in mind calls for heat loads up to 20 watts, a set-point temperature of 294K, and a sink that varies from -220K to nearly as high as the set-point. The overall heat pipe length is 137 cm. Two basically different mechanisms of achieving variable conductance in the pipe by vapor-flow throttling were studied. In one, the thermal resistance between the heat source and sink is due to a saturation-temperature drop corresponding to the vapor-pressure drop developed across the valve. In the other, the pressure difference across the valve induces capillary groove and wick dry out in an evaporation region, and thus results in an increased thermal resistance. This mechanism was selected for fabrication and testing. The pipe is a stainless-steel/methanol two-heat-pipe system. Results are presented and discussed. Engineering drawings and specifications of the pipe are shown.

Eninger, J. E.↗
NASA NTRS1976

Investigation of Critical Burning of Fuel Droplets

An earlier analysis for the combustion response of a liquid monopropellant strand (hydrazine) was extended to consider individual droplets and sprays. While small drops gave low or negative response, large droplets provided response near unity at low frequencies, with the response declining at frequencies greater than the characteristic liquid phase frequency. Temperature gradients in the liquid phase resulted in response peaks greater than unity. A second response peak was found for large drops which corresponded to gas phase transient effects. Spray response was generally reduced from the response of the largest injected droplet, however, even a small percentage of large droplets can yield appreciable response. An apparatus was designed and fabricated to allow observation of bipropellant fuel spray combustion at elevated pressures. A locally homogeneous model was developed to describe this combustion process which allows for high pressure phenomena associated with the thermodynamic critical point.

Chanin, S. P.↗
NASA NTRS1975

The solidification under zero gravity conditions of binary alloys exhibiting solid state immiscibility

The solidification behavior of gold-silicon alloys containing up to 25 at. % silicon was studied, and a mathematical model of gravity segregation during solidification was developed. A background of knowledge is provided which can be used in the design of zero gravity solidification experiments to be carried out in the 300-ft drop tower, in Aerobee rockets and in future space missions. Such experiments are needed to develop the basic scientific knowledge required for the design of economically viable space manufacturing processes. Some preliminary zero gravity experiments were carried out on a gold-25 at. % silicon alloy using the drop tower facility.

Johnson, A. A.↗
NASA NTRS1975

Study of cryogenic propellant systems for loading the space shuttle. Part 2: Hydrogen systems

Computer simulation studies of liquid hydrogen fill and vent systems for the space shuttle are studied. The computer programs calculate maximum and minimum permissible flow rates during cooldown as limited by thermal stress considerations, fill line cooldown time, pressure drop, flow rates, vapor content, vent line pressure drop and vent line discharge temperature. The input data for these programs are selected through graphic displays which schematically depict the part of the system being analyzed. The computed output is also displayed in the form of printed messages and graphs. Digital readouts of graph coordinates may also be obtained. Procedures are given for operation of the graphic display unit and the associated minicomputer and timesharing computer.

Steward, W. G.↗
NASA NTRS1976

Difference thresholds for judgments of sink rate during the flare

Past studies have shown that touchdown rates of descent (sink rates) are higher in aircraft simulators than in aircraft under similar conditions. The objective of this paper was to use a psychophysical technique to investigate a pilot's ability to distinguish between two different sink rates close to the ground. The pilots observed a collimated computer graphics display of a typical runway with edge, zone, and centerline lights. The results showed that with a forward velocity of 120 knots, pilots could reliably distinguish between a sink rate of 0.5 m/sec (1.7 ft/sec) and 0.9 m/sec (2.9 ft/sec). The results also showed that the absolute rate of sink did not significantly affect the perception of sink rate. Time of sink and total height drop during the sink did affect the minimum detectable difference between sink rates (the differential threshold). The effects were such that a greater time of sink and greater height drop produced lower thresholds

Palmer, E.↗
NASA NTRS1976

Oscillatory combustion of monopropellant droplets

A theoretical study of combustion response to imposed pressure oscillations was conducted for monopropellant droplets and sprays. A first-order perturbation analysis was used, yielding the linear response. Transient gas phase phenomena were considered in some cases, but the bulk of the calculations assume a quasi-steady gas phase. The calculations employed properties representative of hydrazine decomposition. Calculated steady combustion results and response predictions for large hydrazine droplets agreed favorably with earlier measurements. Droplet and spray response factors in excess of unity were found. High response was associated with high pressures (1000-10,000 kN/sq m), large droplets, large mean liquid temperature gradients, and frequencies near the characteristic frequency of the liquid phase thermal wave. Spray response factors are lower than the response factor of the largest injected drop, however, a small percentage of large drops can still provide substantial response for the combustion process.

Chanin, S. P.↗
NASA NTRS1976

Development of technology for the fabrication of reliable laminar flow control panels on subsonic transports

The feasibility of using porous composite materials (Kevlar, Doweave, and Leno Weave) as lightweight, efficient laminar flow control (LFC) surface materials is compared to the metallic 319L stainless Dynapore surfaces and electron beam drilled composite surfaces. Areas investigated include: (1) selection of the LFC-suitable surface materials, structural materials, and fabrication techniques for the LFC aircraft skins; (2) aerodynamic static air flow test results in terms of pressure drop through the LFC panel and the corresponding effective porosity; (3) structural design definition and analyses of the panels, and (4) contamination effects on static drop and effective porosity. Conclusions are presented and discussed.

Source record↗
NASA NTRS1977

Behavior of fluids in a weightless environment

Fluid behavior in a low-g environment is controlled primarily by surface tension forces. Certain fluid and system characteristics determine the magnitude of these forces for both a free liquid surface and liquid in contact with a solid. These characteristics, including surface tension, wettability or contact angle, system geometry, and the relationships governing their interaction, are discussed. Various aspects of fluid behavior in a low-g environment are then presented. This includes the formation of static interface shapes, oscillation and rotation of drops, coalescence, the formation of foams, tendency for cavitation, and diffusion in liquids which were observed during the Skylab fluid mechanics science demonstrations. Liquid reorientation and capillary pumping to establish equilibrium configurations for various system geometries, observed during various free-fall (drop-tower) low-g tests, are also presented. Several passive low-g fluid storage and transfer systems are discussed. These systems use surface tension forces to control the liquid/vapor interface and provide gas-free liquid transfer and liquid-free vapor venting.

Fester, D. A.↗
NASA NTRS1977

Catalytic combustion for the automotive gas turbine engine

Fuel injectors to provide a premixed prevaporized fuel-air mixture are studied. An evaluation of commercial catalysts was performed as part of a program leading to the demonstration of a low emissions combustor for an automotive gas turbine engine. At an inlet temperature of 800 K, a pressure of 500,000 Pa and a velocity of 20 m/s a multiple-jet injector produced less than + or - 10 percent variation in Jet-A fuel-air ratio and 100 percent varporization with less than 0.5 percent pressure drop. Fifteen catalytic reactors were tested with propane fuel at an inlet temperature of 800 K, a pressure of 300,000 Pa and inlet velocities of 10 to 25 m/s. Seven of the reactors had less than 2 percent pressure drop while meeting emissions goals of 13.6 gCO/kg fuel and 1.64 gHC/kg fuel at the velocities and exit temperatures required for operation in an automotive gas turbine engine. NO sub x emissions at all conditions were less than 0.5 ppm. All tests were performed with steady state conditions.

Anderson, D. N.↗
NASA NTRS1977

Engine Hydraulic Stability

An analytical injector model was developed specifically to analyze combustion instability coupling between the injector hydraulics and the combustion process. This digital computer dynamic injector model will, for any imposed chamber of inlet pressure profile with a frequency ranging from 100 to 3000 Hz (minimum) accurately predict/calculate the instantaneous injector flowrates. The injector system is described in terms of which flow segments enter and leave each pressure node. For each flow segment, a resistance, line lengths, and areas are required as inputs (the line lengths and areas are used in determining inertance). For each pressure node, volume and acoustic velocity are required as inputs (volume and acoustic velocity determine capacitance). The geometric criteria for determining inertances of flow segments and capacitance of pressure nodes was set. Also, a technique was developed for analytically determining time averaged steady-state pressure drops and flowrates for every flow segment in an injector when such data is not known. These pressure drops and flowrates are then used in determining the linearized flow resistance for each line segment of flow.

Kesselring, R. C.↗
NASA NTRS1978

Calibration target for temperature radiometer

Technique measures temperature/voltage drop characteristics of very thin filament. With constant current running through filament, voltage drop is recorded at various temperatures, as measured by calibrated thermocouple.

Edwards, S. F.↗
NASA NTRS1977

Development and evaluation of die materials for use in the growth of silicon ribbons by the inverted ribbon growth process, task 2, LSSA project

Silicon sessile drop experiments were performed on a variety of commercially available refractory carbides, nitrides, oxides, and borides to examine the potential of these materials for applications involving either direct contact with molten silicon or as substrates for CVD coatings in the fabrication of dies and crucibles for containing molten silicon. Simultaneous experiments were also conducted with CVD layers of SiC, Si3N4, and SiOxNy. Silicon nitride layers, deposited with NH3:SiH4 ratios ranging from 100:1 down to 5:1, were examined in sessile drop experiments to determine if the layers are degraded as a result of using lower reagent ratios. Preliminary experiments were undertaken on the stability of CVD Si3N4 near the melting point of silicon. Silicon ribbon segments were grown from vitreous carbon dies which had been coated with CVD Si3N4. Depending upon the purity of the die materials, ribbon resistivity values up to 40 Omega cm were obtained.

Duffy, M. T.↗
NASA NTRS1978

Experimental study of the effects of flameholder geometry on emissions and performance of lean premixed combustors

Emissions of NOx, CO, and unburned hydrocarbons (UHC) are reported for a lean premixed propane-air system at inlet conditions of 800K and 1MPa using twelve flameholder designs. The flameholders tested represent six design concepts with two values of blockage for each concept. Data were obtained at reference velocities of 35 m/s, 25 m/s and 20 m/s at combustor stations 10 cm and 30 cm downstream of the flameholders. Flameholder pressure drop was found to be a principal determinant of emissions performance. Designs producing larger pressure drops also produced less NOx, CO, and UHC emissions. The lean stability limit equivalence ratio was found to be approximately 0.35 for all designs. Flashback velocities (axial components in the flameholder passages) varied between 30 m/s and 40 m/s. A perforated plate flameholder was operated with a velocity as low as 23 m/s through the perforations at equivalence ratio 0.7 without producing flashback.

Roffe, G.↗