SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The rolling moment induced on aircraft models in the wake of a model of a subsonic transport and of a supersonic transport was measured as a function of angle of attack for several configurations. The tests are described and an analysis of the data is given in this memorandum.
A force test of a scale model of the Space Shuttle Solid Rocket Booster was conducted in a trisonic wind tunnel. The model was tested with such protuberances as a camera capsule, electrical tunnel, attach rings, aft separation rockets, ET attachment structure, and hold-down struts. The model was also tested with the nozzle at gimbal angles of 0, 2.5, and 5 degrees. The influence of a unique heat shield configuration was also determined. Some photographs of model installations in the tunnel were taken and are included. Schlieren photography was utilized for several angles of attack.
An investigation was conducted in the Langley V/STOL tunnel to determine the performance, stability and control, and rotor-wake interaction effects of a powered tilt-proprotor aircraft model with gimbal-hub rotors. Tests were conducted at representative flight conditions for hover, helicopter, transition, and airplane flight. Force and moment data were obtained for the complete model and for each of the two rotors. In addition to wind-speed variation, the angle of attack, angle of sideslip, rotor speed, rotor collective pitch, longitudinal cyclic pitch, rotor pylon angle, and configuration geometry were varied. The results, presented in graphical form, are available in tabular form to facilitate the validation of analytical methods of defining the aerodynamic characteristics of tilt-proprotor configurations.
An investigation has been conducted in the Langley 16-foot transonic tunnel to verify analytically predicted benefits in climb and cruise performance due to blowing the jet exhaust over the wing for a transport configuration. A wing-body model - powered-nacelle rig combination was tested at Mach numbers of 0.5 and 0.8 at angles of attack from -2 to 4 deg and jet total pressure ratios from jet off to 3 or 4 (depending on Mach number) for a variety of nacelle locations relative to the wing. Results from this investigation show that the induced drag for the wing-body (nacelles were nonmetric) was reduced for virtually all configurations. In addition to the experimental results, comparisons of the data with available prediction methods are included to show their validity and capabilities.
Experimental results on the Reynolds number influence on the leeside flowfield of planar delta wings at supersonic speeds are presented. Wind tunnel experiments on two delta wing models with straight and sharp leading edges at freestream Mach number of 2.5 and 3.5 and angle of attack between 1 deg and 12.5 deg were carried out. The cross-sectional shape was triangular and the relative height was 0.25. The flow types investigated were to the left and right of the Stanbrook-Squire boundary. Under leading-edge separation conditions, the vortex position and intensity, and thus the suction pressure, vary with Re while the flow type remains nearly unchanged. In the region of separation with embedded shock, Re affects not only the shape of the separation bubble and pressure level near the leading edge but also the type of flow. At sufficiently high Re the flow type of separation with shock changes to one with shock-induced separation.
An empirical method is presented for computing top centerline heating on the Space Shuttle Orbiter at simulated reentry conditions. It is shown that the Shuttle's top centerline can be thought of as being under the influence of a swept cylinder flow field. The effective geometry of the flow field, as well as top centerline heating, are directly related to oil-flow patterns on the upper surface of the fuselage. An empirical turbulent swept cylinder heating method was developed based on these considerations. The method takes into account the effects of the vortex-dominated leeside flow field without actually having to compute the detailed properties of such a complex flow. The heating method closely predicts experimental heat-transfer values on the top centerline of a Shuttle model at Mach numbers of 6 and 10 over a wide range in Reynolds number and angle of attack.
An investigation of the subsonic longitudinal aerodynamic characteristics of a modified arrow-wing model was conducted in the Langley 4- by 7-Meter Tunnel. This investigation addressed the effectiveness of the leading and trailing edge flap deflections of this model. The arrow wing was tested at a Mach number of 0.02 and at an angle-of-attack range from -4 deg to 24 deg. The results of the investigation showed that deflecting the leading edge and trailing edge in combination could promote an attached-flow condition at the wing leading edge. Also, the leading edge suction could be maximized over the complete lift-coefficient range by scheduling a combination of leading and trailing edge flap deflections.
The phase change paint technique was used to make heat transfer measurements on the windward wing/elevons area of Space Shuttle Orbiter models with differentially deflected elevons. Outboard elevons were deflected windward at angles from 0 to 20 deg. The inboard elevons were deflected leeward. The models were tested in air at Mach 6 and 10 with two flow conditions and three angles of attack for both Mach numbers. Heat transfer coefficient contour maps of the wing/elevon area were obtained for all test conditions. The maximum heat transfer coefficient on the outboard elevon and on certain areas of the wing that were obtained when the elevons were deflected are compared to values obtained when the elevons were undeflected.
Static pressure coefficient distributions on the forebody, afterbody, and nozzles of a 1/12 scale F-15 propulsion model was determined in the 16 foot transonic tunnel for Mach numbers from 0.60 to 1.20, angles of attack from -2 deg to 7 deg and ratio of jet total pressure to free stream static pressure from 1 up to about 7, depending on Mach number. The effects of nozzle geometry and horizontal tail deflection on the pressure distributions were investigated. Boundary layer total pressure profiles were determined at two locations ahead of the nozzles on the top nacelle surface. Reynolds number varied from about 1.0 x 10 to the 7th power per meter, depending on Mach number.
Vortex flow modeling is used to calculate the steady inviscid incompressible flow past one, two and three delta wing configurations. The wings are modeled with vortex lattices and the leading and trailing-edge sheets are modeled by segmented straight vortex filaments. Aerodynamic characteristics are obtained for a range of geometry and angle of attack.
This program concentrates on analyzing a limited number of hot corroded components from the field and the carrying out of a series of controlled laboratory experiments to establish the effects of oxide scale and coating chemistry on hot corrosion life. This is to be determined principally from the length of the incubation period, the investigation of the mechanisms of hot corrosion attack, and the fitting of the data generated from the test exposure experiments to an empirical life prediction model.
Heating distributions were measured on a 1.9-percent-scale model of a generic aeroassisted vehicle proposed for missions to a number of planets and for use as a moderate lift-drag ratio Earth orbital transfer vehicle. This vehicle is spherically blunted, 12.84 deg/7 deg biconic with the fore-cone bent upward 7 deg to provide self-trim capability. A straight biconic with the same nose radius and the same half-angles was also tested. The free-stream Reynolds numbers based on model length were equal to about 2 x 10(5) or 9 x 10 (5). The angle of attack, referenced to the aft-cone, was varied from 0 deg to 20 deg. Heating distributions predicted with a parabolized Navier-Stokes (PNS) code are compared with the measurements for the present Reynolds numbers and range of angles of attack. Leeward heating was greatly affected by Reynolds number, with the heating increasing with decreasing Reynolds number for attached flow (low incidence). The opposite was true for separated flow, which occurred when the fore-cone angle of attack exceeded 0.8 times the fore-cone half-angle. Windward heating distributions were predicted to within 10 percent with the PNS code. Leeward heating distributions were predicted qualitatively for both Reynolds numbers, but quantitative agreement was poorer than on the windward side.
A procedure for estimating relative sensitivities in Space Shuttle Orbiter entry heating due to variations from nominal flight parameters is presented. Ballpark values are provided for assessing heating changes caused by off-nominal variations in anglle of attack and Reynolds number for laminar flow conditions. Also, a procedure for scaling heating data obtained on subscale models tested at low-enthalpy wind-tunnel test conditions to high-enthalpy flight conditions using simplified flow analysis techniques is presented and verified with flight and wind-tunnel data. In addition, data are presented illustrating that a significant increase in heating was experienced on the fifth Orbiter flight. The increase was possibly caused by changes in the catalytic properties of the Orbiter thermal protection system surface.
An investigation was conducted in the Langley 16-Foot Transonic Tunnel to determine the effect of a boattail angle and wedge-size trade on the performance of nonaxisymmetric wedge nozzles installed on a generic twin-engine fighter aircraft model. Test data were obtained at static conditions and at Mach numbers from 0.60 to 1.25. Angle of attack was held constant at 0 deg. High-pressure air was used to simulate jet exhaust, and the nozzle pressure ratio was varied from 1.0 (jet off) to slightly over 15.0. For the configurations studied, the results indicate that wedge size can be reduced without affecting aeropropulsive performance.
An analytical study was conducted to predict the effect of an oscillating stream on the time dependent sectional pressure and lift coefficients of a model propeller blade. The assumption is that as the blade sections encounter a wake, the actual angles of attack vary in a sinusoidal manner through the wake, thus each blade is exposed to an unsteady stream oscillating about a mean value at a certain reduced frequency. On the other hand, an isolated propeller at some angle of attack can experience periodic changes in the value of the flow angle causing unsteady loads on the blades. Such a flow condition requires the inclusion of new expressions in the formulation of the unsteady potential flow around the blade sections. These expressions account for time variation of angle of attack and total shed vortices in the wake of each airfoil section. It was found that the final expressions for the unsteady pressure distribution on each blade section are periodic and that the unsteady circulation and lift coefficients exhibit a hysteresis loop.
An axisymmetric panel code was used to evaluate a series of ducted propeller inlets. The inlets were tested in the Lewis 9 by 15 Foot Low Speed Wind Tunnel. Three basic inlets having ratios of shroud length to propeller diameter of 0.2, 0.4, and 0.5 were tested with the Pratt and Whitney ducted prop/fan simulator. A fourth hybrid inlet consisting of the shroud from the shortest basic inlet coupled with the spinner from the largest basic inlet was also tested. This later configuration represented the shortest overall inlet. The simulator duct diameter at the propeller face was 17.25 inches. The short and long spinners provided hub-to-tip ratios of 0.44 at the propeller face. The four inlets were tested at a nominal free stream Mach number of 0.2 and at angles of attack from 0 degrees to 35 degrees. The panel code method incorporated a simple two-part separation model which yielded conservative estimates of inlet separation.
A large scale model of a generic three-dimensional sidewall compression scramjet inlet has been designed based on the results of a computational parametric study for testing in the 31-inch Mach 10 Hypersonic Wind Tunnel at the NASA Langley Research Center. In order to increase the instrumentation density in interaction regions for a highly instrumented model, it is desirable to make the model as large as possible. When the cross-sectional area of a model becomes large relative to the inviscid core size of the tunnel, the effects of blockage must be considered. In order to assess these effects, a blockage model (an inexpensive, much less densely instrumented version of the configuration) was fabricated for preliminary testing. Since it was desired to determine both the effect of the model on the performance of the wind tunnel and also to determine if the inlet would start, the model possessed a total of 32 static pressure orifices distributed on the forebody plane and sidewalls; seventeen static pressure orifices on the tunnel wall and 3 pitot probes on the model monitored the tunnel performance. This paper presents the design considerations in the development of the wind tunnel model and the blockage aspects of the effects of contraction ratio, cowl location, Reynolds number, and angle of attack.
The aerodynamics of small amplitude pitching motions near stall have been studied experimentally in order to improve understanding of the torsional stall flutter problem for propeller blades. A model wing was oscillated in pitch at several small amplitudes over a wide and representative range of conditions. Unsteady surface pressures were measured and integrated to determine the aerodynamic damping at five spanwise stations. Strong negative damping was found for motions centered near static stall for all studied reduced frequencies, Mach numbers, and sweep angles. The 30-deg sweptback configuration was found to become negatively damped over the entire span nearly simultaneously, while the unswept model exhibited local regions of negative damping that moved toward the wing tip as the mean angle of attack was increased.