Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Yield function”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74

Wetting behaviors of fluoroterpolymer fiber films

Various aspects of electrospun fibers prepared from terpolymer of tetrafluoroethylene (TFE), hexafluoropropylene (HFP), and vinylidene fluoride (VDF) (THV)/acetone solutions at two applied voltages, THV/acetone solutions having Texas montmorillonite with two ratios, and THV/ethyl acetate solutions using two needle sizes are described. Fibers from THV/acetone and THV/ethyl acetate solutions showed shallow indentations and pores, respectively. The clay, functioning as electrospinning agent, did not influence the fiber morphology, but yielded narrower fiber diameter distribution and the thinnest fibers. Heterogeneous fiber diameter distribution and increase in the fiber diameters were observed by lowering the voltage for fibers of THV/acetone solutions. Fibers from THV/ethyl acetate solutions had the largest diameter and the broadest diameter distribution. Electrospun THV fibers having both hydrophobic characteristics with nearly 140° water contact angles and oleophilic properties with oil contact angles less than 45° might have applications in areas such as water/oil separation.

02 PETROLEUM↗

Scalable, Economical Fabrication Processes for Ultra-Compact Warm-White LEDs

Conventional warm-white LED component fabrication consists of a large number of sequential steps which are required to incorporate electrical, mechanical, and optical functionality into the component. Each of these steps presents cost and yield challenges which multiply throughout the entire process. Although there has been significant progress in LED fabrication over the last decade, significant advances are needed to enable further reductions in cost per lumen while not sacrificing efficacy or color quality. Cree conducted a focused 18-month program to develop a new low-cost, high-efficiency light emitting diode (LED) architecture enabled by novel large-area parallel processing technologies, reduced number of fabrication steps, and minimized raw materials use. This new scheme is expected to enable ultra-compact LED components exhibiting simultaneously high efficacy and high color quality. By the end of the program, Cree fabricated warm-white LEDs with a room-temperature “instant on” efficacy of >135 lm/W at ~3500K and 90 CRI (when driven at the DOE baseline current density of 35 A/cm2). Cree modified the conventional LED fabrication process flow in a manner that is expected to translate into simultaneously high throughput and yield for ultra-compact packages. Building on its deep expertise in LED wafer fabrication, Cree developed these ultra-compact LEDs to have no compromises in color quality or efficacy compared to their conventional counterparts. Despite their very small size, the LEDs will also be robustly electrically integrated into luminaire systems with the same attach yield as conventional packages. The versatility of the prototype high-efficacy LED architecture will likely benefit solid-state lighting (SSL) luminaire platforms ranging from bulbs to troffers. We anticipate that the prototype LEDs will particularly benefit luminaires with large numbers of distributed compact packages, such as linear and area luminaires (e.g. troffers). The fraction of total SSL luminaire cost made up by the LEDs themselves has steadily fallen over the past several years, but can still make up 30% or more of the bill of materials; the new LED design will radically lower this proportion. Ultra-compact, highly efficient LEDs with optimal distribution in the system will further benefit luminaire materials and assembly costs by reducing the complexity and volume of thermal management and optical subsystems.

42 ENGINEERING↗

A Thin Lens Model for Charged-Particle RF Accelerating Gaps

Presented is a thin-lens model for an RF accelerating gap that considers general axial fields without energy dependence or other a priori assumptions. Both the cosine and sine transit time factors (i.e., Fourier transforms) are required plus two additional functions; the Hilbert transforms the transit-time factors. The combination yields a complex-valued Hamiltonian rotating in the complex plane with synchronous phase. Using Hamiltonians the phase and energy gains are computed independently in the pre-gap and post-gap regions then aligned using the asymptotic values of wave number. Derivations of these results are outlined, examples are shown, and simulations with the model are presented.

43 PARTICLE ACCELERATORS↗

Linear and Nonlinear Constitutive Model for Piezoelectricity in ALEGRA-FE

This report develops and documents linear and nonlinear constitutive relations implemented in ALEGRA-FE (ferroelectric). A thermodynamic framework is created to describe the electromechanical system in the form of a free energy functional. Constitutive relations are derived by taking series expansions of the free energy functional with respect to the independent fields. First order expansion terms yield linear constitutive relations and higher order expansion terms yield non-linear constitutive relations. This document serves as supplement to Section 4 of Sandia Report SAND2013-7363, Rev 3. Methods for implementation of kinematic relations of piezoelectric models and rotation of material principal axes are covered in the supplemented report. Additional discussion on phase velocity calculation is also presented.

30 DIRECT ENERGY CONVERSION↗

Transforming our understanding of chloroplast-associated genes through comprehensive characterization of protein localizations and protein-protein interactions

Bioenergy crops are a renewable source of fuels and are a critical base for building a carbon-neutral economy. Rational engineering of bioenergy crops has the potential to enhance the yields. However, our ability to engineer plants is limited because the functions of most genes remain unknown. Systematic characterization of gene function in plants thus has the potential to greatly accelerate bioenergy research. Here, we focus on the chloroplast, an underexplored energy-producing organelle that is a hallmark of plants. The chloroplast is one of the promising targets of biofuel crop engineering efforts because of its central role in photosynthesis, metabolism, and intracellular signaling. However, the protein composition of the chloroplast and the functions of most of its proteins remain poorly characterized. At the core of this project, we sought to comprehensively determine the localization of chloroplast-associated proteins and generate a spatially defined protein-protein interaction network for chloroplast. For this purpose, we used the leading model alga Chlamydomonas reinhardtii, which greatly increased experimental speed and throughput. We illustrated the value of our findings to land plants by determining the localization of Arabidopsis thaliana land plant homologs of the Chlamydomonas proteins. Altogether, we were successful in determining the localization of 1,034 chloroplast-associated proteins in Chlamydomonas. The localizations provide numerous insights into the spatial organization of chloroplasts and how they function to support photosynthesis. The localization patterns of distinct proteins revealed new chloroplast structures and revealed new spatial organization inside the chloroplast. We also identified new components of known chloroplast structures, such as the chloroplast envelope, nucleoid, plastoglobuli, and pyrenoid. We identified these new components by investigating the interacting partners of known proteins. Many proteins localized in both the chloroplast and other cellular structures, thereby hinting at new functions and communication between cellular structures. We also applied machine learning on the atlas to generate predictions for the location of all of the proteins in Chlamydomonas. This enabled us to assign putative functions to many uncharacterized proteins based on their cellular location. Altogether, this research establishes a rich resource that opens new avenues of investigation and guides future work in deciphering and manipulating chloroplast function. Next, we developed an extensive protein-protein interaction network for the chloroplast by performing affinity purification-mass spectrometry on ~1,150 tagged chloroplast-associated proteins, the first such large-scale study in any photosynthetic organism. This dataset reveals 4,694 high-confidence protein-protein interactions, offering insights into the functions of thousands of conserved poorly-characterized chloroplast proteins. This systematic identification of protein-protein interactions in the chloroplast also provides multiple exciting new research directions and a detailed blueprint of the chloroplast's operation. This research lays the groundwork to decipher the inner workings of the chloroplast, the cell structure at the heart of photosynthesis. The spatial atlas and protein-protein interactions reveal chloroplast organizational features that would not have been accessible with traditional approaches. The localization mapping, insights into the function, and research materials generated further provide a rich resource for the research community to advance the understanding of how the chloroplast is organized to enable engineering of enhanced photosynthetic organisms.

59 BASIC BIOLOGICAL SCIENCES↗

Photo-stability of super-hydrogenated PAHs determined by action spectroscopy experiments

We have investigated the photo-stability of pristine and super-hydrogenated pyrene cations (C{sub 16}H{sub 10+m}{sup +},m=0,6, or 16) by means of gas-phase action spectroscopy. Optical absorption spectra and photo-induced dissociation mass spectra are presented. By measuring the yield of mass-selected photo-fragment ions as a function of laser pulse intensity, the number of photons (and hence the energy) needed for fragmentation of the carbon backbone was determined. Backbone fragmentation of pristine pyrene ions (C{sub 16}H{sub 10}{sup +}) requires absorption of three photons of energy just below 3 eV, whereas super-hydrogenated hexahydropyrene (C{sub 16}H{sub 16}{sup +}) must absorb two such photons and fully hydrogenated hexadecahydropyrene (C{sub 16}H{sub 26}{sup +}) only a single photon. These results are consistent with previously reported dissociation energies for these ions. Our experiments clearly demonstrate that the increased heat capacity from the additional hydrogen atoms does not compensate for the weakening of the carbon backbone when pyrene is hydrogenated. In photodissociation regions, super-hydrogenated Polycyclic Aromatic Hydrocarbons (PAHs) have been proposed to serve as catalysts for H{sub 2} formation. Our results indicate that carbon backbone fragmentation may be a serious competitor to H{sub 2} formation at least for small hydrogenated PAHs like pyrene.

79 ASTRONOMY AND ASTROPHYSICS↗

Slicing of silicon into sheet material: Silicon sheet growth development for the large area silicon sheet task of the Low Cost Silicon Solar Array project

The limits of blade tolerance were defined. The standard blades are T-2 thickness tolerance. Good results were obtained by using a slurry fluid consisting of mineral oil and a lubricity additive. Adjustments of the formulation and fine tuning of the cutting process with the new fluid are necessary. Test results and consultation indicate that the blade breakage encountered with water based slurries is unavoidable. Two full capacity (974 wafer) runs were made on the large prototype saw. Both runs resulted in extremely low yield. However, the reasons for the low yield were lack of proper technique rather than problems with machine function. The test on the effect of amount of material etched off of an as-sawn wafer on solar cell efficiency were completed. The results agree with previous work at JPL in that the minimum material removed per side that gives maximum efficiency is on the order of 10 microns.

Fleming, J. R.↗

Proposed method for determining the thickness of glass in solar collector panels

An analytical method was developed for determining the minimum thickness for simply supported, rectangular glass plates subjected to uniform normal pressure environmental loads such as wind, earthquake, snow, and deadweight. The method consists of comparing an analytical prediction of the stress in the glass panel to a glass breakage stress determined from fracture mechanics considerations. Based on extensive analysis using the nonlinear finite element structural analysis program ARGUS, design curves for the structural analysis of simply supported rectangular plates were developed. These curves yield the center deflection, center stress and corner stress as a function of a dimensionless parameter describing the load intensity. A method of estimating the glass breakage stress as a function of a specified failure rate, degree of glass temper, design life, load duration time, and panel size is also presented.

Moore, D. M.↗

Fermi-Compton scattering due to magnetopause surface fluctuations in Jupiter's magnetospheric cavity

The effects of boundary surface fluctuations on a spectrum of electromagnetic radiation trapped in a high Q (quality) cavity are considered. Undulating walls introduce small frequency shifts at reflection to the radiation, and it is argued that the process is entirely analogous to both Fermi (particle) acceleration and inverse Compton scattering. A Fokker-Planck formalism is pursued; it yields a diffusion equation in frequency for which the Green's function and steady-state solutions are found. Applying this analysis to the Jovian continuum radiation discovered by Voyager spacecraft, it is suggested that characteristic diffusion times are greater than 1 year, and that in order to account for the steep frequency spectra observed, an unidentified loss mechanism must operate in the cavity with a decay time constant approximately equal to the characteristic diffusion time divided by 28. A radiator-reactor model of the cavity is investigated to provide an estimate for the intrinsic luminosity of the low frequency (approximately 100 Hz) continuum source whose power is approximately 7 x 10 to the 6th W.

Barbosa, D. D.↗

Formal convergence characteristics of elliptically constrained incremental Newton-Raphson algorithms

Various aspects of the convergence, uniqueness, and existence properties associated with solutions generated via the elliptically constrained incremental Newton-Raphson (ECINR) algorithm are analyzed. Several theorems are developed, and the formal behavior of the elliptically constrained scheme developed by Padovan (1981) is discussed in detail. Consideration is given to global and local rates of convergence, to the determination of the occurrence of safety zones wherein the algorithm yields inherently convergent results, to formal limitations on the class of functions which the scheme can be applied to solve, and to single and multidimensional formalisms on existence uniqueness and convergence. Special attention is given to functions whose Jacobian matrix exhibit positive, negative, semi and indefinite properties. Several significant advantages of ECINR over the classical INR are mentioned.

Padovan, J.↗

Impact cratering and spall failure at gabbro

Both hypervelocity impact and dynamic spall experiments were carried out on a series of well-indurated samples of gabbro. The impact experiments carried out with 0.04 to 0.2g, 5-6 km/sec projectiles produced deci-centimeter-sized craters and demonstrated crater efficiencies of 6/10 to the - 9 g/erg, and order of magnitude greater than in metal and some two to three times that of previous experiments on less strong igneous rocks. Most of the crater volume (some 60 to 80%) is due to spall failure. Distribution of cumulative fragment number, as a function of mass of fragments with masses greater than 0.1 gram yield values of b = d(log10N sub f)dlog10(m)of -0.5 to -0.6, where N sub f is the cumulate number of fragments and m is the mass of fragments. These values are in agreement or slightly higher than those obtained for less strong rocks and indicate that a large fraction of the ejectra resides in a few large fragments.

Lange, M. A.↗

Impact cratering and spall failure of gabbro

Both hypervelocity impact and dynamic spall experiments were carried out on a series of well-indurated samples of gabbro. The impact experiments carried out with 0.04 to 0.2 g, 5-6 km/sec projectiles produced deci-centimeter-sized craters and demonstrated crater efficiencies of 6/10 to the -9 g/erg, and order of magnitude greater than in metal and some two to three times that of previous experiments on less strong igneous rocks. Most of the crater volume (some 60 to 80 percent) is due to spall failure. Distribution of cumulative fragment number, as a function of mass of fragments with masses greater than 0.1 gram yield values of b = d(log10N sub f)dlog10(m) of -0.5 to -0.6, where N sub f is the cumulate number of fragments and m is the mass of fragments. These values are in agreement or slightly higher than those obtained for less strong rocks and indicate that a large fraction of the ejecta resides in a few large fragments.

Lange, M. A.↗

Solar-cell interconnect design for terrestrial photovoltaic modules

Useful solar cell interconnect reliability design and life prediction algorithms are presented, together with experimental data indicating that the classical strain cycle (fatigue) curve for the interconnect material does not account for the statistical scatter that is required in reliability predictions. This shortcoming is presently addressed by fitting a functional form to experimental cumulative interconnect failure rate data, which thereby yields statistical fatigue curves enabling not only the prediction of cumulative interconnect failures during the design life of an array field, but also the quantitative interpretation of data from accelerated thermal cycling tests. Optimal interconnect cost reliability design algorithms are also derived which may allow the minimization of energy cost over the design life of the array field.

Mon, G. R.↗

SASS wind ambiguity removal by direct minimization. II - Use of smoothness and dynamical constraints

A variational analysis method (VAM) is used to remove the ambiguity of the Seasat-A Satellite Scatterometer (SASS) winds. The VAM yields the best fit to the data by minimizing an objective function S which is a measure of the lack of fit. The SASS data are described and the function S and the analysis procedure are defined. Analyses of a single ship report which are analogous to Green's functions are presented. The analysis procedure is tuned and its sensitivity is described using the QE II storm. The procedure is then applied to a case study of September 6, 1978, south of Japan.

Hoffman, R. N.↗

Lorentz-covariant dissipative Lagrangian systems

The concept of dissipative Hamiltonian system is converted to Lorentz-covariant form, with evolution generated jointly by two scalar functionals, the Lagrangian action and the global entropy. A bracket formulation yields the local covariant laws of energy-momentum conservation and of entropy production. The formalism is illustrated by a derivation of the covariant Landau kinetic equation.

Kaufman, A. N.↗

Application of shock wave data to earth and planetary science

It is pointed out that shock wave data for: (1) low temperature condensable gases H2 and He, (2) H2O, CH4, NH3, CO, CO2, and N2 ices, and (3) silicates, metals, oxides and sulfides have many applications in geophysics and planetary science. The present paper is concerned with such applications. The composition of planetary interiors is discussed, taking into account the division of the major constituent of the planets in three groups on the basis of 'cosmic abundance' arguments, the H-He mixtures in the case of Jupiter and Saturn, shock wave data for hydrogen, and constraints on the internal structure of Uranus and Neptune. Attention is also given to the earth's mantle, shock wave data for mantle materials, the earth's core, impacts on planetary surfaces, elastic wave velocities as a function of pressure along the Hugoniot of iron, and reactions which yield the CO2 bearing atmospheres for Venus, earth, and Mars.

Ahrens, T. J.↗

A low-cost optical data acquisition system for vibration measurement

A low cost optical data acquisition system was designed to measure deflection of vibrating rotor blade tips. The basic principle of the new design is to record raw data, which is a set of blade arrival times, in memory and to perform all processing by software following a run. This approach yields a simple and inexpensive system with the least possible hardware. Functional elements of the system were breadboarded and operated satisfactorily during rotor simulations on the bench, and during a data collection run with a two-bladed rotor in the Lewis Research Center Spin Rig. Software was written to demonstrate the sorting and processing of data stored in the system control computer, after retrieval from the data acquisition system. The demonstration produced an accurate graphical display of deflection versus time.

Posta, S. J.↗

Simulation of double layers in a model auroral circuit with nonlinear impedance

A reduced circuit description of the U-shaped potential structure of a discrete auroral arc, consisting of the flank transmission line plus parallel-electric-field region, is used to provide the boundary condition for one-dimensional simulations of the double-layer evolution. The model yields asymptotic scalings of the double-layer potential, as a function of an anomalous transport coefficient alpha and of the perpendicular length scale l(a) of the arc. The arc potential phi(DL) scales approximately linearly with alpha, and for alpha fixed phi (DL) about l(a) to the z power. Using parameters appropriate to the auroral zone acceleration region, potentials of phi (DPL) 10 kV scale to projected ionospheric dimensions of about 1 km, with power flows of the order of magnitude of substorm dissipation rates.

Smith, R. A.↗