Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Vehicles”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Heavy Lift Launch Vehicles for 1995 and Beyond

A Heavy Lift Launch Vehicle (HLLV) designed to deliver 300,000 lb to a 540 n mi circular polar orbit may be required to meet national needs for 1995 and beyond. The vehicle described herein can accommodate payload envelopes up to 50 ft diameter by 200 ft in length. Design requirements include reusability for the more expensive components such as avionics and propulsion systems, rapid launch turnaround time, minimum hardware inventory, stage and component flexibility and commonality, and low operational costs. All ascent propulsion systems utilize liquid propellants, and overall launch vehicle stack height is minimized while maintaining a reasonable vehicle diameter. The ascent propulsion systems are based on the development of a new liquid oxygen/hydrocarbon booster engine and liquid oxygen/liquid hydrogen upper stage engine derived from today's SSME technology. Wherever possible, propulsion and avionics systems are contained in reusable propulsion/avionics modules that are recovered after each launch.

Toelle, R.↗
NASA NTRS1981

Aerodynamic drag reduction tests on a box-shaped vehicle

The intent of the present experiment is to define a near optimum value of drag coefficient for a high volume type of vehicle through the use of a boattail, on a vehicle already having rounded front corners and an underbody seal, or fairing. The results of these tests will constitute a baseline for later follow-on studies to evaluate candidate methods of obtaining afterbody drag coefficients approaching the boattail values, but without resorting to such impractical afterbody extensions. The current modifications to the box-shaped vehicle consisted of a full and truncated boattail in conjunction with the faired and sealed underbody. Drag results from these configurations are compared with corresponding wind tunnel results of a 1/10 scale model. Test velocities ranged up to 96.6 km/h (60 mph) and the corresponding Reynolds numbers ranged up to 1.3 x 10 to the 7th power based on the vehicles length which includes the boattail. A simple coast-down technique was used to define drag.

Peterson, R. L.↗
NASA NTRS1985

Manrating orbital transfer vehicle propulsion

The expended capabilities for Orbital Transfer Vehicles (OTV) which will be needed to meet increased payload requirements for transporting materials and men to geosynchronous orbit are discussed. The requirement to provide manrating offers challenges and opportunities to the propulsion system designers. The propulsion approaches utilized in previous manned space vehicles of the United States are reviewed. The principals of reliability analysis are applied to the Orbit Transfer Vehicle. Propulsion system options are characterized in terms of the test requirements to demonstrate reliability goals and are compared to earlier vehicle approaches.

Cooper, L. P.↗
NASA NTRS1986

Aerothermodynamics of transatmospheric vehicles

A transatmospheric vehicle (TAV) using airbreathing propulsion requires a long acceleration period within the denser part of the atmosphere to reach orbital speed. The long flight time, coupled with the need for a low-drag configuration, results in severe heating of parts of the vehicle. The ascent peak stagnation point and wing leading edge equilibrium wall temperatures are about 3500 K and 2500 K, respectively, likely requiring some form of mass addition cooling. The corresponding temperatures during entry are 1000 K lower. The vehicle windward centerline temperatures are more moderate, with values peaking around 1300 K during both ascent and entry. Therefore, radiative cooling should be effective over large areas of the vehicle. The windward centerline heat loads during entry are comparable to those for low acceleration ascent trajectories. However, ascent heat loads for the stagnation point and the wing leading edge are about three times higher than those during entry. For comparison, the entry heat load for the TAV's stagnation point is about three times higher than the value for Shuttle. Therefore the ascent heat load at the TAV's stagnation point exceeds the Shuttle's entry value by an order of magnitude.

Tauber, M. E.↗
NASA NTRS1985

An Orbital Maneuvering Vehicle simulator

The Orbital Maneuvering Vehicle (OMV) is a teleoperated vehicle designed to dock with a target vehicle in space to peform certain tasks. This vehicle is not yet in production, but a simulator of the OMV is located at Marshall Space Flight Center (MSFC). The MSFC facility provides a realistic simulation of the OMV. Various docking maneuvers can be studied in some detail. A special robot has been constructed that provides a moving target for the simulator to dock with. This facility is valuable for conducting studies on the OMV; it also is excellent for personnel training.

Teoh, W.↗
NASA NTRS1986

Thrust vectoring for single-stage-to-orbit, horizontal takeoff, horizontal landing, space vehicles

The preliminary design of a horizontal takeoff, horizontal landing, single-stage-to-orbit, rocket-powered space vehicle was performed. The purpose was to examine technology requirements for future small payload launch vehicles. The distinguishing aspect of the design was the utilization of thrust vectoring to provide half of the lift at takeoff. The inclusion of a canard was necessary to provide additional lift at takeoff and to balance the moments produced with thrust vectoring. A weights estimation, an aerodynamic assessment, a trajectory analysis, and a gear weight analysis were performed. The takeoff weight of the resulting vehicle was approximately 1.26 million pounds, based on advanced technology structures and subsystems. The vehicle was designed to deliver a 5000-pound payload to a polar orbit.

Cunningham, M. J.↗
NASA NTRS1986

Orbital transfer vehicle launch operations study. Volume 1: Executive summary

The purpose was to use the operational experience at the launch site to identify, describe and quantify the operational impacts of the various configurations on the Kennedy Space Center (KSC) and/or space station launch sites. Orbital Transfer Vehicle (OTV) configurations are being developed/defined by contractor teams. Lacking an approved configuration, the KSC Study Team defined a Reference Configuration to be used for this study. This configuration then become the baseline for the identification of the facilities, personnel and crew skills required for processing the OTV in a realistic manner that would help NASA achieve the lowest possible OTV life cycle costs. As the study progressed, researchers' initial apraisal that the vehicle, when delivered, would be a sophisticated, state-of-the-art vehicle was reinforced. It would be recovered and reused many times so the primary savings to be gained would be in the recurring-cycle of the vehicle operations--even to the point where it would be beneficial to break from tradition and make a significant expenditure in the development of processing facilities at the beginning of the program.

Source record↗
NASA NTRS1986

Status of advanced propulsion for space based orbital transfer vehicle

A new Orbital Transfer Vehicle (OTV) propulsion system will be required to meet the needs of space missions beyond the mid-1990's. As envisioned, the advanced OTV will be used in conjunction with Earth-to-orbit vehicles, Space Station, and Orbit Maneuvering Vehicle. The OTV will transfer men, large space structures, and conventional payloads between low Earth and higher energy orbits. Space probes carried by the OTV will continue the exploration of the solar system. When lunar bases are established, the OTV will be their transportation link to Earth. NASA is currently funding the development of technology for advanced propulsion concepts for future Orbital Transfer Vehicles. Progress in key areas during 1986 is presented.

Cooper, L. P.↗
NASA NTRS1986

Earth-to-orbit launch for vehicles for manned Mars mission application

Manned Mars missions (MMMs) will require payloads to low Earth orbit (LEO) much heavier and larger than can be accommodated with the Shuttle. Three typical launch vehicles are described that could possibly satisfy the MMM needs. The vehicle concepts include Shuttle Derived Vehicles (SDVs), which are composed essentially of Shuttle components, and Heavy Lift Launch Vehicles (HLLVs), which utilize new and improved technologies and require additional development.

M Page↗
NASA NTRS1987

Aeroelastic effects in multirotor vehicles. Part 2: Methods of solution and results illustrating coupled rotor/body aeromechanical stability

This report is a sequel to the earlier report titled, Aeroelastic Effects in Multi-Rotor Vehicles with Application to Hybrid Heavy Lift System, Part 1: Formulation of Equations of Motion (NASA CR-3822). The trim and stability equations are presented for a twin rotor system with a buoyant envelope and an underslung load attached to a flexible supporting structure. These equations are specialized for the case of hovering flight. A stability analysis, for such a vehicle with 31 degrees of freedom, yields a total of 62 eigenvalues. A careful parametric study is performed to identify the various blade and vehicle modes, as well as the coupling between various modes. Finally, it is shown that the coupled rotor/vehicle stability analysis provides information on both the aeroelastic stability as well as complete vehicle dynamic stability. Also presented are the results of an analytical study aimed at predicting the aeromechanical stability of a single rotor helicopter in ground resonance. The theoretical results are found to be in good agreement with the experimental results, thereby validating the analytical model for the dynamics of the coupled rotor/support system.

Venkatesan, C.↗
NASA NTRS1987

An evaluation of metallized propellants based on vehicle performance

An analytical study was conducted to determine the improvements in vehicle performance possible by burning metals with conventional liquid bipropellants. These metallized propellants theoretically offer higher specific impulse, increased propellant density and improved vehicle performance compared with conventional liquid bipropellants. Metals considered were beryllium, lithium, aluminum and iron. Liquid bipropellants were H2/O2, N2H4/N2O4, RP-1/O2 and H2/F2. A mission with a delta V = 4267.2 m/sec (14,000 ft/sec) and vehicle with propellant volume fixed at 56.63 cu m (2000 cu ft) and dry mass fixed at 2761.6 kg (6000 lb) was used, roughly representing the transfer of a chemically propelled upper-stage vehicle from a low-Earth orbit to a geosynchronous orbit. The results of thermochemical calculations and mission analysis calculations for bipropellants metallized with beryllium, lithium, aluminum and iron are presented. Technology issues pertinent to metallized propellants are discussed.

Zurawski, Robert L.↗
NASA NTRS1987

Geometric description and grid generation for space vehicles

The understanding and analysis of three dimensional fluid behavior around reentry vehicles, like the Space Shuttle Orbiter, is of considerable importance for flight applications. Vehicle designers need pressure, heat transfer, and shear distributions to support design activities. Traditionally these have been obtained by experimental data. Significant reduction in design costs can be obtained if the calculated results based on finite difference procedures are used to verify and supplement experimental results. Computing the flow field over Space Shuttle Orbiter, which has complex cross sectional geometries is a major problem. A first step in this direction is development of body definition and grid generation procedure. In this project a digitized body definition and grid generation procedure, developed earlier at JSC, is modified and applied to the Shuttle Orbiter X24C-10D. Two dimensional grid and body definition for various sections of the space vehicle is obtained using the differential equation method. This study demonstrates that this geometry and grid generation procedure can be applied to other aerospace vehicles such as aerospaceplanes.

Krishna, Madakasira G.↗
NASA NTRS1985

System technology analysis of aeroassisted orbital transfer vehicles: Moderate lift/drag (0.75-1.5), Volume 1B, part 2, study results

A complete compilation of the results from Phase 2 of a study to identify and prioritize the technology payoffs of representative space based mid lift/drag ratio (L/D) aeroassisted orbit transfer vehicles (AOTV) and the cryofueled propulsion subsystem - configuration interactions is presented. Several combinations of basing and launch vehicle options, staging scenarios, missions (delivery, servicing, or manned round trip), and target orbits were considered. Space basing of an AOTV opens up numerous configuration opportunities. The size can exceed the launch vehicle cargo bay envelope by resorting to orbital assembly and the AOTV weight can exceed the launch vehicle capability. With the absence of fully fueled tanks during a ground based launch much lighter gossamer type structures are possible that may result in performance gains. At the Space Station, payload rearranging or manifesting may prove attractive. Several major conclusions regarding aerothermodynamics, aerodynamics, payload manifesting, the propulsion subsystem, and systems issues are discussed.

Source record↗
NASA NTRS1987

An Adaptive Numeric Predictor-corrector Guidance Algorithm for Atmospheric Entry Vehicles

An adaptive numeric predictor-corrector guidance is developed for atmospheric entry vehicles which utilize lift to achieve maximum footprint capability. Applicability of the guidance design to vehicles with a wide range of performance capabilities is desired so as to reduce the need for algorithm redesign with each new vehicle. Adaptability is desired to minimize mission-specific analysis and planning. The guidance algorithm motivation and design are presented. Performance is assessed for application of the algorithm to the NASA Entry Research Vehicle (ERV). The dispersions the guidance must be designed to handle are presented. The achievable operational footprint for expected worst-case dispersions is presented. The algorithm performs excellently for the expected dispersions and captures most of the achievable footprint.

Spratlin, Kenneth Milton↗
NASA NTRS1986

A review of shock waves around aeroassisted orbital transfer vehicles

Aeroassisted orbital transfer vehicles (AOTVs) are a proposed type of reusable spacecraft that would be used to transport cargoes from one earth-bound orbit to another. Such vehicles could be based on the proposed space station and used to transport commercial satellites from the space station to geostationary orbits or to polar orbits and return. During a mission, AOTVs would fly through earth's atmosphere, thus generating aerodynamic forces that could be used for decelerating the vehicles or changing their direction. AOTV research findings were concerned with the shock-wave-induced, high-temperature airflows that would be produced around these vehicles during atmospheric flight. Special emphasis was placed on the problems of: (1) the chemical physics of multitemperature, ionizing, nonequilibrium air flows, and (2) the dynamics of the flows in the base region of a blunt body with complex afterbody geometry.

Park, C.↗
NASA NTRS1986

Prospects for advanced rocket-powered launch vehicles

The potential for advanced rocket-powered launch vehicles to meet the challenging cost, operational, and performance demands of space transportation in the early 21st century is examined. Space transportation requirements from recent studies underscoring the need for growth in capacity in support of an increasing diversity of space activities and the need for significant reductions in operational and life-cycle costs are reviewed. Fully reusable rocket powered concepts based on moderate levels of evolutionary advanced technology are described. These vehicles provide a broad range of attractive concept alternatives with the potential to meet demanding operational and cost goals and the flexibility to satisfy a variety of vehicle architecture, mission, vehicle concept, and technology options.

Eldred, C. H.↗
NASA NTRS1986

Status of advanced propulsion for space based orbital transfer vehicle

A new Orbital Transfer Vehicle (OTV) propulsion system will be required to meet the needs of space missions beyond the mid-1990's. As envisioned, the advanced OTV will be used in conjunction with earth-to-orbit vehicles, Space Station, and Orbit Maneuvering Vehicle. The OTV will transfer men, large space structures, and conventional payloads between low earth and higher energy orbits. Space probes carried by the OTV will continue the exploration of the solar system. When lunar bases are established, the OTV will be their transportation link to earth. NASA is currently funding the development of technology for advanced propulsion concepts for future Orbital Transfer Vehicles. Progress in key areas during 1986 is presented.

Cooper, Larry P.↗
NASA NTRS1987

Results from the vehicle charging and potential experiment on STS-3

The Vehicle Charging and Potential Experiment formed part of the scientific experiments comprising the NASA Office of Space Sciences-1 pallet flown at an altitude of 250 km and an orbital inclination of 40 deg on the third flight of the Space Shuttle Orbiter in March 1982. Details of the objectives, the instrumentation of the experiment, and some preliminary results from the individual instruments are presented. The experiment studied passive vehicle charging using thermal plasma probes, and it is concluded that apart from moderate v x B (L)-induced electrical potential resulting from the large size and restricted plasma contact area, the Space Shuttle Orbiter behaved similarly to smaller spacecraft orbiting in the same ionospheric region. However, an unexpected passive orbital result was the detection of enhanced plasma density in the vicinity of the Orbiter under restricted orbital conditions, apparently composed of contaminant molecular species and with an electron component having a temperature considerably higher than the ambient ionosphere electrons. The active vehicle charging experiments were performed by using a 100 mA/1 keV electron beam emitted out of the payload bay. Charging measurements made during short electron beam pulse emissions provide an upper limit of about 1 mF for the Orbiter capacitance. Steady-state charging measurements showed that for the vehicle attitudes covered by the mission, the induced electrical potential was normally only a few volts, except during some nighttime conditions when it rose above 40 V.

Banks, P. M.↗