Results for “Validated Models” — Page 74

DOE OSTI2021

Propagation of Input Uncertainties in Numerical Simulations of Laser Powder Bed Fusion

Laser powder bed fusion has the potential of redefining state-of-the-art processing and production methods, but defect formation and inconsistent build quality have limited the implementation of this process. Numerical models are widely used to study this process and predict the formation of these defects. Presently, the uncertainties of model input parameters and thermophysical properties used by these numerical simulations have not been investigated. In the present study, the uncertainty in these input parameters and material properties are quantified for laser powder bed fusion, with and without a simulated powder bed, to determine their influence on the predictive accuracy of an experimentally validated numerical model. Accounting for all possible sources of uncertainty quickly becomes computationally expensive on account of the curse of dimensionality. Uncertainty in laser absorption, solid, and liquid specific heat of the metal were found to have the largest effect on model prediction reliability with or without the use of a powder bed. Results also illustrate that accounting for these three uncertain parameters still captures the majority of model prediction uncertainty. Furthermore, the methodology of this study may be used to understand the uncertainty in as-built microstructure through propagation to microstructure prediction models, or applied under processing conditions where high Péclet numbers are observed and the thermal convection and fluid flow within the molten pool are substantial.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

QUIC-URB and QUIC-fire extension to complex terrain: Development of a terrain-following coordinate system

Ensemble-based approaches to prescribed fire planning cannot be supported by CFD-based models like FIRETEC and WFDS because they are too computationally expensive and cannot leverage LES approaches like CAWFE and WRF-SFIRE because too coarse of resolution. QUIC-Fire was developed to fill this gap but it cannot currently address complex terrain, typical for instance of the Western United States. In this paper, we describe the extension of the diagnostic wind model QUIC-URB, the wind engine of QUIC-Fire, to a terrain-following coordinate system. In particular, the paper presents the mathematical derivation of the wind solver leading to a linear system of equations that are solved through the successive over-relaxation method. The model is validated against a standard test used in previous works (the Askervein Hill) and against a new dataset from measurements in the Socorro Mountains, New Mexico. The terrain-following implementation captured the correct phenomenology for the isolated Askervein Hill, with a wind speed up at the top of the hill. We report the model agreed well with measurements on the upwind side of the peak, but overestimated speed-up on the downwind side of the hill. This is due to the inability of the model to generate flow separation and wake-eddy dynamics. On a common laptop, the divergence-free wind field was obtained in 6 s, making the solver appealing for coupled fire–atmosphere simulations. The Socorro Mountain was highly complex, with many cliff faces, peaks, and valleys. Although the model captures the magnitude and direction of inlet and outlet areas of the domain, it performs rather poorly in the valley region and in the regions near the steep cliffs. Hence, the model shows good agreement with data in areas of open sloped terrain but lacks in areas where flow separation and thermally driven effects may be present (neither effect was addressed in this work). Results highlight that future work should focus on the implementation of parameterizations of wake-eddies, similar to QUIC-URB’s building parameterizations, and on thermodynamic-driven flow.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2023

Modeling of plasma beta effects on the island divertor transport in the standard configuration of W7-X

The influence of plasma beta effects on the edge plasma transport in the Wendelstein 7-X standard configuration is studied systematically by using EMC3-EIRENE combined with a 3D equilibrium code named HINT. The magnetic topology changes induced by plasma beta effects are significantly reflected in plasma transport behaviors and heat flux patterns on divertor targets. After validating the modeling strategy by comparisons with experimental data, the extended simulations for high performance plasmas show that the threshold separatrix density for accessing the power detachment is reduced in higher beta plasmas. Compared with the vacuum field case, the impurity radiation distributions with finite beta effects are modified in the magnetic island region. The divertor heat flux is distributed more evenly along the toroidal direction on the strike line at the vertical target. The strike line on the horizontal target moves towards the pumping gap with an increase in the plasma beta. In addition, the different pressure profiles with the same central beta also result in a modified heat flux pattern on the divertor targets.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Performance evaluation of a wrapped around condenser for heat pump water heater applications

In this report, accurate performance evaluation of a wrapped-around condenser for heat pump water heaters (WHPWH) is critical since the COP of the system depends heavily on thermal stratification and condenser design. An analytical, quasi-steady state heat balance method has been developed to determine the optimal spacing between adjacent channels, tube diameter, tube shape, and total refrigerant charge amount for the condenser. The heat transfer rate is compared among three approaches: the refrigerant thermodynamic model, the condenser-wrap fin model, and the analytical natural convection model on the inside of the tank for the three regions based on the refrigerant phase (e.g., super-heated, saturated, or subcooled). The heat transfer rate was predicted by a combination of slug-plug and annular flow for a D-shaped helical tube. Experimental data were used as boundary conditions for validating the model. The rate of heat transfer based on tube shape and tank wall temperatures was compared by CFD analysis. Parametric analysis indicates a tradeoff between refrigerant mass, pressure drop, tube diameter, and tube length to maximize the heat transfer rate. The model suggests the saturated region length can be extended by 400%, and the condenser pressure drop can be reduced by 23% with an optimal spacing pattern.

42 ENGINEERING↗

DOE OSTI2025

Reconstructing f ( T ) gravity and exploring the torsion driven warm inflationary cosmology

The current paper reports an investigation of a warm inflationary scenario in the context of f(T) gravity for a spatially flat FLRW universe. In our model, inflation is driven purely by the torsional sector of f(T) gravity, without introducing any additional scalar fields. We focus on the high dissipative regime (R >> 1), reconstruct the Hubble parameter as a function of the e-folding number N, and derive the slow-roll parameters ε 1 (N) and ε 2 (N). The study has encapsulated the dynamics of inflation and its duration under strong dissipation. The dissipative coefficient Γ is modeled with a temperature-dependent power-law form, linking the inflationary dynamics to thermal corrections and the particle content of the early universe. The analysis has affirmed that the torsion-induced energy density ρ T successfully transitions to radiation energy density ρ rad , facilitating a graceful exit from inflation. Finally, we have validated our model by comparing the scalar spectral index and tensor-to-scalar ratio with Planck 2018 results, demonstrating consistency within observational bounds. Additionally, it is verified that the thermal domination condition T * /H > 1 and the torsion dominance condition ρ T /ρ rad > 1 are satisfied.

Ghosh, Moli [Amity University, Kolkata (India); Mr↗

DOE OSTI2021

Resolving Anodic Current and Temperature Distributions in a Polymer Electrolyte Membrane Water Electrolysis Cell Using a Pseudo-Two-Phase Computational Fluid Dynamics Model

Expanding upon our prior experimental work, we constructed a three-dimensional model of a polymer electrolyte membrane water electrolyzer using computational fluid dynamics. We applied the assumption of pseudo-two-phase flow, the flow of two phases with equal velocity. Experimental data were used to obtain parameters and to determine the conditions under which this model was valid. Anodic distributions of current density, temperature, liquid saturation, and relative humidity were obtained at various flow rates. The overall current density and temperature difference from inlet to outlet at the anode agreed strongly with experimental measurements under most circumstances. This verification allowed us to further examine the apparent gas coverage calculated from experimental and model temperature data. Results suggested a low liquid saturation and low relative humidity at the anode due to the consumption of liquid water and water vapor. However, we questioned the accuracy of the pseudo-two-phase assumption at low water feed rates. We concluded that the model was applicable to systems with liquid water feed rates greater than 0.6 ml min -1 cm -2 . Therefore, it is a fair screening method that can advise which operating conditions lead to excessive temperatures or drying at the anode, thereby promoting the longevity of the membrane and catalyst.

25 ENERGY STORAGE↗

DOE OSTI2023

Neural network model of neutral beam injection in the EAST tokamak to enable fast transport simulations

The neutral beam injection (NBI) system in EAST produces energetic neutral particles, which collide with electrons and ions in tokamak plasmas and heat the plasmas through Coulomb collisions. Moreover, it drives a non-inductive source of current, due to the charge-exchange collision between neutral particles and ions, and injects toroidal torque, which generates a toroidal rotation of the plasma. The effect caused by the NBI system, such as plasma heating, current drive, total neutron rate, momentum transfer, and shine-through, are modeled by a comprehensive module called NUBEAM. However, NUBEAM is computationally intensive since it relies on Monte Carlo methods. In this work, a neural network model has been developed as a surrogate model for NUBEAM in EAST. The database for neural-network model training, validation and testing is generated by running TRANSP for experimental discharges from recent EAST campaigns (after the latest NBI upgrade) while using the NUBEAM module. Simulation results illustrate that the trained neural network has the capability of replicating the predictions made by NUBEAM while demanding a significantly shorter execution time. Finally, these results indicate that surrogate models like the one proposed in this work could enable fast transport simulations for EAST after integrating them into a control-oriented predictive code such as COTSIM.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

A hybrid analytical and numerical model for cross-over and performance decay in a unit cell vanadium redox flow battery

Developing an accurate and efficient model for cross-over is critical for improving the long-term performance of redox flow batteries (RFBs). Here, this work presents a hybrid analytical and numerical model that combines a two-dimensional analytical solution to the active species, a one-dimensional analytical model for cross-over mechanisms, and a zero-dimensional numerical model for outlet concentrations of reactants. By comparing with experiment over 41 cycles (ca. 144 h), the model reported a mean voltage difference of 0.0089 V, mean time difference of 14 s per cycle (of 3.5 h), maximum relative difference for capacity and energy of 1.34% and 1.63%, respectively. The predicted mean concentrations for V 2+ , V 3+ , and VO$_{2}^{+}$ in membrane are 65%~77% of measured values from the literature. Upon validation, the model reproduced behaviors in electrolyte imbalance similar to those observed in experiments and numerical models, and revealed the control of cross-over, self-discharge, stoichiometry of side reactions, and Coulombic efficiency on electrolyte imbalance. The model also demonstrates excellent computational efficiency for simulating 41 cycles (around 37,000 points) within 3~4 s. The demonstrated efficiency and accuracy for predicting cross-over and its impacts on voltage, capacity&energy decay, membrane concentrations, and electrolyte imbalance makes it a reliable tool for optimizing RFBs’ long-term performance.

25 ENERGY STORAGE↗

DOE OSTI2021

Nitromethane Decomposition via Automated Reaction Discovery and an Ab Initio Corrected Kinetic Model

In the explore the systematic construction of kinetic models from in silico reaction data for the decomposition of nitromethane. Our models are constructed in a computationally affordable manner by using reactions discovered through accelerated molecular dynamics simulations using the ReaxFF reactive force field. The reaction paths are then optimized to determine reaction rate parameters. We introduce a reaction barrier correction scheme that combines accurate thermochemical data from density functional theory with ReaxFF minimal energy paths. We validate our models across different thermodynamic regimes, showing predictions of gas phase CO and NO concentrations and high-pressure induction times that are similar to experimental data. The kinetic models are analyzed to find fundamental decomposition reactions in different thermodynamic regimes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Numerical Investigation of Fuel Property Effects on Mixed-Mode Combustion in a Spark-Ignition Engine

In this research, lean mixed-mode combustion is numerically investigated using computational fluid dynamics (CFD) in a spark-ignition engine. A new E30 fuel surrogate is developed using a neural network model with matched octane numbers. A skeletal mechanism is also developed by automated mechanism reduction and by incorporating a NO x submechanism. A hybrid approach that couples the G-equation model and the well-stirred reactor model is employed for turbulent combustion modeling. The developed CFD model is shown to well predict pressure and apparent heat release rate (AHRR) traces compared with experiment. Two types of combustion cycles (deflagration-only and mixed-mode cycles) are observed. The mixed-mode cycles feature early flame propagation and subsequent end-gas auto-ignition, leading to two distinctive AHRR peaks. The validated CFD model is then employed to investigate the effects of NO x chemistry. The NO x chemistry is found to promote auto-ignition through the residual gas, while the deflagration phase remains largely unaffected. Sensitivity analysis is finally performed to understand effects of fuel properties, including heat of vaporization (HoV) and laminar flame speed (S L ). An increased HoV tends to suppress auto-ignition through charge cooling, while the impact of HoV on flame propagation is insignificant. In contrast, an increased S L is found to significantly promote both flame propagation and end-gas auto-ignition. The promoting effect of S L on auto-ignition is not a direct chemical effect; it is rather caused by an advancement of the combustion phasing, which increases compression heating of the end-gas.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

State of the Art Gap Analysis of PV Models [Slides]

This report identifies the needed parameters and dynamic characteristics that will determine the test plan.

14 SOLAR ENERGY↗

DOE OSTI2025

Insights Into Thermal Runaway Mechanisms: Fast Tomography Analysis of Metal Agglomerates in Lithium-Ion Batteries

Thermal Runaway (TR) in lithium-ion batteries (LIB) is a critical technological and social concern. Whilst such events are rare, TR is characterized by uncontrollable heating leading to catastrophic failures. To deepen the understanding of the failure process and subsequently develop more accurate TR prediction models and as a result safer battery systems, we present in this work high-speed X-ray tomography for in-depth investigations of the copper current collector melting and agglomeration during TR. The melting process presents valuable real-time internal information about heat evolution during TR, previously challenging to access but crucially important for validating TR models. In this work, controlled failure studies combined with high-speed X-ray tomography were performed on two different commercial LIB models, subjecting them to both external heating and nail penetration to induce TR. Through real-time observation via high-speed tomography, followed by segmentation, rendering, and analysis, the formation of copper agglomerates was qualitatively and quantitatively characterized and visualized for the first time. Agglomerates tended to form either from the battery's outermost layers or centrally, depending on the method of TR initiation, and gives an indirect insight into the internal temperature evolution and distribution. Moreover, an initial comparative analysis between the battery models also revealed differences in agglomerate size, which has been linked to the thicker copper current collectors of one of the cell models. We further discuss the impact of larger copper agglomerates on heat distribution and safety. This study not only sheds light on the intricate dynamics of TR in LIBs but also underscores the pivotal role of 'gold-standard' imaging techniques in advancing battery safety, crucial for the robust modeling of TR and the future design of electric vehicle safety systems.

25 ENERGY STORAGE↗

DOE OSTI2020

Geometric Scale-up Experiments on Fluidization of Geldart B Glass Beads

The objective of this work is to provide a valuable database from controlled experiments for validating computational models. Recently, coarse-grained techniques such as particle-in-cell (PIC) or coarse-grained discrete element modeling (DEM) have gained popularity due to their computational efficiency while modeling large-scale systems; however, the influence of model parameters and their sensitivities at different geometric scales and flow conditions remain to be analyzed. These datasets are critical for the multiphase flow research community to assess predictive capability of modeling techniques as well as elucidate the hydrodynamic behavior in these systems. This study performed fluidization experiments using three different test sections with internal diameters of 2.5, 4, and 6 in. The operating conditions, bed material, and range of flow velocities at the inlet were constant in all the units, which were not hydrodynamically scaled. Glass beads having a Sauter Mean Diameter of 332 μm were used. Superficial velocity was varied from 2.97 to 5.35 times the minimum fluidization velocity and the initial static bed height was 0.1524 m. The order in which the experiments were performed was randomized and replicates were included to provide uncertainty in measurements. Statistics of differential pressure and bed height from these tests were reported. Future plans include validating PIC methodology in the open-source software, MFiX (Multiphase Flow with Interphase Exchanges) using results from this study. This could further be extended to determine optimal model parameters using inverse techniques such as deterministic calibration or Bayesian inference.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2020

Geometric Scale-up Experiments on Fluidization of Geldart B Glass Beads

The objective of this work is to provide a valuable database from controlled experiments for validating computational models. Recently, coarse-grained techniques such as particle-in-cell (PIC) or coarse-grained discrete element modeling (DEM) have gained popularity due to their computational efficiency while modeling large-scale systems; however, the influence of model parameters and their sensitivities at different geometric scales and flow conditions remain to be analyzed. These datasets are critical for the multiphase flow research community to assess predictive capability of modeling techniques as well as elucidate the hydrodynamic behavior in these systems. This study performed fluidization experiments using three different test sections with internal diameters of 2.5, 4, and 6 in. The operating conditions, bed material, and range of flow velocities at the inlet were constant in all the units, which were not hydrodynamically scaled. Glass beads having a Sauter Mean Diameter of 332 μm were used. Superficial velocity was varied from 2.97 to 5.35 times the minimum fluidization velocity and the initial static bed height was 0.1524 m. The order in which the experiments were performed was randomized and replicates were included to provide uncertainty in measurements. Statistics of differential pressure and bed height from these tests were reported. Future plans include validating PIC methodology in the open-source software, MFiX (Multiphase Flow with Interphase Exchanges) using results from this study. This could further be extended to determine optimal model parameters using inverse techniques such as deterministic calibration or Bayesian inference.

42 ENGINEERING↗

DOE OSTI2020

Linking metabolic phenotypes to pathogenic traits among “ Candidatus Liberibacter asiaticus” and its hosts

Candidatus Liberibacter asiaticus (CLas) has been associated with Huanglongbing, a lethal vector-borne disease affecting citrus crops worldwide. While comparative genomics has provided preliminary insights into the metabolic capabilities of this uncultured microorganism, a comprehensive functional characterization is currently lacking. Here, we reconstructed and manually curated genome-scale metabolic models for the six CLas strains A4, FL17, gxpsy, Ishi-1, psy62, and YCPsy, in addition to a model of the closest related culturable microorganism, L. crescens BT-1. Predictions about nutrient requirements and changes in growth phenotypes of CLas were confirmed using in vitro hairy root-based assays, while the L. crescens BT-1 model was validated using cultivation assays. Host-dependent metabolic phenotypes were revealed using expression data obtained from CLas-infected citrus trees and from the CLas-harboring psyllid Diaphorina citri Kuwayama. These results identified conserved and unique metabolic traits, as well as strain-specific interactions between CLas and its hosts, laying the foundation for the development of model-driven Huanglongbing management strategies.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2025

Development of a data-driven neural network model for electron thermal transport in NSTX

A data-driven electron thermal transport neural network (ETT-NN) model, trained on TRANSP interpretative analysis results of National Spherical Torus Experiment (NSTX), was developed to enable faster and more accurate ETT computation for spherical tokamaks (STs). The model incorporates both convolutional NNs and recurrent NNs, allowing it to simultaneously account for the spatial and temporal non-localities and multi-scale features of turbulent transport, which have been considered only in a limited manner in conventional models. The model was validated through interpretative analysis and predictive simulations using Tokamak Reactor Integrated Automated Suite for Simulation and Computation, demonstrating relatively high accuracy. Additionally, parameter scans were performed on test discharges known to exhibit specific turbulent modes, such as microtearing mode, trapped electron mode, kinetic ballooning mode, and electron temperature gradient mode. The scanning results revealed that the ETT-NN model exhibits the same trends as those observed in conventional gyrokinetic simulations or theories, while also capturing the global nature of turbulent transport, indicating that the data-driven model accurately reflects the underlying physical characteristics. Furthermore, due to the dimensionless nature of the model, we can feasibly expand its applicability by incorporating data from other devices and uncovering the characteristics of ETT in STs in the future.

NSTX↗

DOE OSTI2026

Data for Soil Oxygen Dynamics: A Key Mediator of Tile Drainage Impacts on Coupled Hydrological, Biogeochemical, and Crop Systems

Tile drainage removes excess water and is an essential, widely adopted management practice to enhance crop productivity in the US Midwest and throughout the world. Tile drainage has been shown to significantly change hydrological and biogeochemical cycles by lowering the water table and reducing the residence time of soil water, although examining the complex interactions and feedbacks in an integrated hydrology–biogeochemistry–crop system remains elusive. Oxygen dynamics are critical to unraveling these interactions and have been ignored or oversimplified in existing models. Understanding these impacts is essential, particularly so because tile drainage has been highlighted as an adaptation under projected wetter springs and drier summers in the changing climate in the US Midwest. We used the ecosys model that uniquely incorporates first-principle soil oxygen dynamics and crop oxygen uptake mechanisms to quantify the impacts of tile drainage on hydrological and biogeochemical cycles and crop growth in corn–soybean rotation fields. The model was validated with data from a multi-treatment, multi-year experiment in Washington, IA. The relative root mean square error (rRMSE) for the corn and soybean yield in validation is 5.66 % and 12.57 %, respectively. The Pearson coefficient (r) of the monthly tile flow during the growing season is 0.78. Plant oxygen stress turns out as an emergent property of the equilibrium between the soil oxygen supply and biological demand. The impact of tile drainage on the system is achieved through a series of coupled feedback mechanisms. The model results show that tile drainage reduces the soil water content and enhances soil oxygenation. It additionally increases the subsurface discharge and elevates inorganic nitrogen leaching, with seasonal variations influenced by climate and crop phenology. The improved aerobic condition alleviates crop oxygen stress during wet springs, thereby promoting crop root growth during the early growth stage. The development of greater root density, in turn, mitigates water stress during dry summers, leading to an overall increase in the crop yield by ∼6 %. These functions indicate the potential of tile drainage in bolstering crop resilience to climate change and the use of this modeling tool for large-scale assessments of tile drainage. The model reveals the underlying causal mechanisms that drive the agroecosystem response to drainage on the coupled hydrology, biogeochemistry, and crop system dynamics.

Modeling↗

DOE OSTI2025

Soil oxygen dynamics: a key mediator of tile drainage impacts on coupled hydrological, biogeochemical, and crop systems

Tile drainage removes excess water and is an essential, widely adopted management practice to enhance crop productivity in the US Midwest and throughout the world. Tile drainage has been shown to significantly change hydrological and biogeochemical cycles by lowering the water table and reducing the residence time of soil water, although examining the complex interactions and feedbacks in an integrated hydrology–biogeochemistry–crop system remains elusive. Oxygen dynamics are critical to unraveling these interactions and have been ignored or oversimplified in existing models. Understanding these impacts is essential, particularly so because tile drainage has been highlighted as an adaptation under projected wetter springs and drier summers in the changing climate in the US Midwest. We used the ecosys model that uniquely incorporates first-principle soil oxygen dynamics and crop oxygen uptake mechanisms to quantify the impacts of tile drainage on hydrological and biogeochemical cycles and crop growth in corn–soybean rotation fields. The model was validated with data from a multi-treatment, multi-year experiment in Washington, IA. The relative root mean square error (rRMSE) for the corn and soybean yield in validation is 5.66 % and 12.57 %, respectively. The Pearson coefficient (r) of the monthly tile flow during the growing season is 0.78. Plant oxygen stress turns out as an emergent property of the equilibrium between the soil oxygen supply and biological demand. The impact of tile drainage on the system is achieved through a series of coupled feedback mechanisms. The model results show that tile drainage reduces the soil water content and enhances soil oxygenation. It additionally increases the subsurface discharge and elevates inorganic nitrogen leaching, with seasonal variations influenced by climate and crop phenology. The improved aerobic condition alleviates crop oxygen stress during wet springs, thereby promoting crop root growth during the early growth stage. The development of greater root density, in turn, mitigates water stress during dry summers, leading to an overall increase in the crop yield by ∼6 %. These functions indicate the potential of tile drainage in bolstering crop resilience to climate change and the use of this modeling tool for large-scale assessments of tile drainage. The model reveals the underlying causal mechanisms that drive the agroecosystem response to drainage on the coupled hydrology, biogeochemistry, and crop system dynamics.

60 APPLIED LIFE SCIENCES↗