Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Transportation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74

Colloidal metal transport in soils developing on historic coal mine spoil

Chemical weathering of pyrite via oxidative dissolution is well-known for generating Fe(III)-bearing colloids at acid mine drainage (AMD) sites; however, the potential for physical weathering of pyrite-bearing materials and subsequent release and transport of colloidal pyrite and associated trace metals has not been studied. Here, we monitored the colloidal metal transport in soil developing on abandoned coal mine spoil with a history of AMD generation to systematically study the contribution of colloids to base and trace metal transport and determine the elemental and mineralogical composition of colloids. Additionally, we collected soil pore water using lysimeters with a pore size of approximately 1.3 μm and centrifugation was used to separate the colloids from aqueous fractions. Metal concentrations of Na, Ca, Mg, K, Si, Al, Mn, Fe, Cu, and Zn were analyzed. Our results show only 14% of the total Al and Cu were present in colloidal fractions whereas 23%, 43%, and 54% of Fe, Mn, and Zn were transported in the colloidal phase, respectively. In contrast, all base metals were primarily present in the aqueous concentration with a small fraction (<10%) present in the colloidal phase. The colloidal fractions of the base metals were inferred to be associated with the concentration of clay colloids. The release of colloids exhibited possible sensitivity toward weather conditions such as alternating high temperatures and rainfall during summer (May–July) compared to fall (August–November). The morphology, elemental, and mineral composition of colloids were determined by a scanning electron microscopy equipped with energy dispersive spectroscopy (SEM-EDS) and X-ray diffraction (XRD). Colloids were dominated by phyllosilicates (biotite, muscovite, and kaolinite) with minor quartz and feldspars. Other minerals phases identified in colloidal fractions were hematite, goethite, arsenopyrite, and chalcopyrite. Colloids consisting of Fe, S, and O with structures resembling framboidal pyrite were identified, which is consistent with the non-silicates minerals identified by XRD. Our study suggests that the physical weathering of pyrite in the mine spoil can generate colloidal pyrite, which is mobilized and transported by soil pore water. Our results also indicate that these pyritic colloids are associated with toxic trace metals including Cu, Mn, and Zn. Colloid mobilization is also impacted by changes in temperature and precipitation, where clay mobilization afer rain events is favored. Further, sudden spikes in aqueous and/or colloidal concentrations may be the result of local heterogeneity within soils developing on mine spoil, indicating that further field-based work is necessary to better characterize pore-scale processes that control aqueous and colloid transport at similar sites to have a better understanding of potential contaminant transport from mine spoil systems.

58 GEOSCIENCES↗

Influence of physical and chemical hydrology on bioremediation of a U-contaminated aquifer informed by reactive transport modeling incorporating 238 U/ 235 U ratios

Microbially-catalyzed reductive immobilization of aqueous uranium (U) as a solid phase has been proposed as a U remediation technique. Both laboratory and field experiments have demonstrated that this reduction reaction alters the 238 U/ 235 U ratio, producing a 238 U-enriched U(IV) solid. In contrast, other major U reactive transport processes fractionate these isotopes much less. This suggests the potential to quantify the extent of bioreduction occurring in groundwater containing U using the 238 U/ 235 U ratio, which would substantially improve upon current practices largely relying on U concentration measurements alone. Current reactive transport models for uranium dynamics include only concentration measurements, which are strongly influenced by highly coupled reactive transformation and aqueous transport processes. The complex physical and chemical behavior of U potentially compromises such quantitative analysis of U storage and release. Here we report the first numerical reactive transport model which explicitly incorporates variations in the 238 U/ 235 U ratio of U and demonstrates improved interpretation of the principal chemical reactions and groundwater transport processes affecting the subsurface mobility and distribution of this widespread contaminant. Recent U bioreduction studies performed in a contaminated aquifer in Rifle, Colorado, USA applied Rayleigh distillation models to interpret U stable isotope fractionation observed as a result of acetate amendment. These simplified models were unable to resolve the spatiotemporal pattern of U isotope fractionation recorded in the aqueous solutes. Here, we employ the multi-component, isotope-enabled CrunchTope reactive transport software to interpret these measured U isotope ratios, and demonstrate accurate reproduction of observed trends in both geochemistry and 238 U/ 235 U ratios for two consecutive years of field experiments. Overall, our results indicate that accurately modeling both the U concentration and isotope ratio distributions greatly constrains the parameter space of the model. We find that the transport properties of U in the Rifle aquifer are governed by the presence of low-permeability regions, which the isotopes are uniquely sensitive to. When U reduction is spatially constrained by these low-permeability regions, the shift in the 238 U/ 235 U ratio becomes more muted. Accurate modeling of observed U isotope ratios thus provides a powerful means to better understand bioremediation, and the current study serves to advance the application of this novel method.

238U/235U↗

Dimensionality effects on multicomponent ionic transport and surface complexation in porous media

Coulombic interactions between charged species in pore water and at surface/solution interfaces are of pivotal importance for multicomponent reactive transport in porous media. In this study, we investigate the impact of domain dimensionality on electrostatically coupled dispersion and surface-solution reactions during transport of acidic plumes and major ions in porous media. Column and quasi two-dimensional flow-through experiments were performed, with identical silica porous media and under the same advection-dominated conditions. Equal mass fluxes of different electrolyte solutions (i.e., HCl - pH ~ 2.8, NaBr - 100 mM, HCl - pH ~ 2.8 plus NaBr - 100 mM) were continuously injected in the 1-D and 2-D experiments and breakthrough curves of pH and major ions were measured at the outlet of the domains. The presence of pronounced ionic strength gradients in the transverse direction in the 2-D setup caused distinct retardation and transport behaviors of protons and major ions which were not observed in the one-dimensional column experiments. Furthermore, in the cases of salt electrolytes injection, considerably enhanced release of H + (>61%) from the quartz surface was observed in the multidimensional system compared to the one-dimensional setup. Reactive transport modeling was performed to reproduce the experimental outcomes and to analyse the coupling between transport processes, based on the Nernst-Planck formulation of diffusive/dispersive fluxes and on surface complexation reactions at the solid-solution interface. Electrostatic interactions between Na + , B – , and H + , and deprotonation of the quartz surface upon the formation of sodium outer-sphere complexes, are the primary controllers of the spatial and temporal features displayed by the pH and major ions measurements. The reactive transport simulations allowed us to interpret the experimental observations, to visualize the distribution and spatio-temporal evolution of dissolved and solid species, to identify a spatially heterogeneous zonation of Coulombic interactions with distinct behavior at the fringe and core of the injected plumes in the multidimensional setup, and to quantify the different components of the Nerst-Planck fluxes of the charged solutes. This study demonstrates that the domain dimensionality directly affects electrostatic interactions between charged aqueous species in the pore water and surface complexation reactions at the solid-solution interface. The non-trivial effects of dimensionality on multicomponent ionic transport result in a significantly different behavior in 1-D and 2-D systems.

58 GEOSCIENCES↗

Techno-economic analysis of conventional and advanced high-pressure tube trailer configurations for compressed hydrogen gas transportation and refueling

Transporting compressed gaseous hydrogen in tube trailers to hydrogen refueling stations (HRSs) is an attractive economic option in early fuel cell electric vehicle (FCEV) markets. This study examines conventional (Type I, steel) and advanced (Type IV, composite) high-pressure tube trailer configurations to identify those that offer maximum payload and lowest cost per unit of deliverable payload under United States Department of Transportation (DOT) size and weight constraints. The study also evaluates the impacts of various tube trailer configurations and payloads on the transportation and refueling cost of hydrogen under various transportation distance and HRS capacity scenarios. Composite tube trailers can transport large hydrogen payloads, up to 1100 kg at 7300 psi (500 bar) working pressure, while steel tube trailer configurations are limited by DOT weight regulations and may transport a maximum hydrogen payload of approximately 270 kg. Using steel pressure vessels to transport hydrogen at high pressure is counterproductive because of the rapid increase in vessel weight with wall thickness. The most economic composite tube trailer configuration includes 30-inch-diameter vessels packed in a 3 x 3 array. A linear relationship between the deliverable payload and the capital cost of a composite tube trailer has been developed for configurations with the lowest cost-per-unit payload. The capital cost is approximately $1100 per kg of deliverable hydrogen payload. Considering the entire delivery pathway (including refueling), tube trailer configurations with smaller vessels packed in greater numbers enable higher payload delivery and lower delivery cost in terms of $/kg H-2, when delivering hydrogen over longer distances to large stations. Selection of the appropriate tube trailer configuration and corresponding hydrogen payload can reduce hydrogen delivery cost by up to 16%. (C) 2018 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.

composite tubes↗

Large language models for transportation research: Methodologies, state of the art, and future opportunities

The rapid rise of large language models (LLMs) is transforming transportation research, with significant advancements emerging between 2023 and 2025, a period marked by the inception and swift growth of adopting and adapting LLMs for various transportation applications. Despite these significant advancements, however, a systematic review and synthesis of the existing literature remains lacking. This paper aims to fill this gap by providing a comprehensive review of the methodologies and applications of LLMs in transportation. We explore key applications, including autonomous driving, travel behavior prediction, and general transportation-related queries, alongside LLM methodologies such as zero- or few-shot learning, prompt engineering, and fine-tuning. From the review, critical research gaps are identified. From the methodological perspective, many of the research limitations can be addressed by integrating LLMs with existing tools and refining LLM architectures. From the application perspective, research opportunities for LLMs to address various transportation challenges are also explored. By synthesizing these findings, this review not only presents the state-of-the-art LLM adoption and adaptation in transportation, but also proposes future research directions as well as insights and recommendations for policymakers and practitioners, paving the way for greater LLM-driven research innovations in transportation in the future.

42 ENGINEERING↗

Fate and transport of uranium (VI) in weathered saprolite

We conducted batch and column experiments to investigate sorption and transport of uranium (U) in the presence of saprolite derived from interbedded shale, limestone, and sandstone sequences. Sorption kinetics were measured at two initial concentrations (C0; 1, 10 mM) and three soil:solution ratios (Rs/w; 0.005, 0.25, 2 kg/L) at pH 4.5 (pH of the saprolite). The rate of U loss from solution (mmole/L/h) increased with increasing Rs/w. Uranium sorption exhibited a fast phase with 80% sorption in the first eight hours for all C0 and Rs/w values and a slow phase during which the reaction slowly approached (pseudo) equilibrium over the next seven days. The pH-dependency of U sorption was apparent in pH sorption edges. U(VI) sorption increased over the pH range 4e6, then decreased sharply at pH > 7.5. U(VI) sorption edges were well described by a surface complexation model using calibrated parameters and the reaction network proposed by Waite et al. (1994). Sorption isotherms measured using the same Rs/w and pH values showed a solids concentration effect where U(VI) sorption capacity and affinity decreased with increasing solids concentration. Moreover, this effect may have been due to either particle aggregation or competition between U(VI) and exchangeable cations for sorption sites. The surface complexation model with calibrated parameters was able to predict the general sorption behavior relatively well, but failed to reproduce solid concentration effects, implying the importance of appropriate design if batch experiments are to be utilized for dynamic systems. Transport of U(VI) through the packed column was significantly retarded. We also conducted transport simulations using the reactive transport model HydroGeoChem (HGC) v5.0 that incorporated the surface complexation reaction network used to model the batch data. Model parameters reported by Waite et al. (1994) provided a better prediction of U transport than optimized parameters derived from our sorption edges. The results presented in this study highlight the challenges in defining appropriate conditions for batch-type experiments used to extrapolate parameters for transport models, and also underline a gap in our ability to transfer batch results to transport simulations.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Sugar transporters in grasses: Function and modulation in source and storage tissues

Carbohydrate partitioning, the process of transporting carbohydrates from photosynthetic (source) tissues, such as leaves, to non-photosynthetic (sink) tissues, such as stems, roots, and reproductive structures, is vital not only for the growth and development of plants but also for withstanding biotic and abiotic stress. In many plants, sucrose is the primary form of carbohydrate loaded into the phloem for long-distance transport and unloaded into the sink tissues for utilization or storage. Here, we highlight recent findings about 1) phloem loading in grasses, 2) the principal families of sugar transporters involved in sucrose transport, and 3) novel mechanisms by which the activities of sugar transporters are modulated. We discuss exciting discoveries from eudicot species that provide valuable insights regarding the regulation of these sugar transporters, which may be translatable to monocot species. As we better understand the intricate pathways that control the activities of various sugar transporters, we can utilize this knowledge for developing improved crop varieties.

59 BASIC BIOLOGICAL SCIENCES↗

Evaluation of the accuracy of an offline seasonally-varying matrix transport model for simulating ideal age

Newton-Krylov solvers for ocean tracers have the potential to greatly decrease the computational costs of spinning up deep-ocean tracers, which can take several thousand model years to reach equilibrium with surface processes. One version of the algorithm uses offline tracer transport matrices to simulate an annual cycle of tracer concentrations and applies Newton’s method to find concentrations that are periodic in time. Here we present the impact of time-averaging the transport matrices on the equilibrium values of an ideal-age tracer. We compared annually-averaged, monthly-averaged, and 5-day-averaged transport matrices to an online simulation using the ocean component of the Community Earth System Model (CESM) with a nominal horizontal resolution of 1° × 1° and 60 vertical levels. We found that increasing the time resolution of the offline transport model reduced a low age bias from 12% for the annually-averaged transport matrices, to 4% for the monthly-averaged transport matrices, and to less than 2% for the transport matrices constructed from 5-day averages. The largest differences were in areas with strong seasonal changes in the circulation, such as the Northern Indian Ocean. As a result, for many applications the relatively small bias obtained using the offline model makes the offline approach attractive because it uses significantly less computer resources and is simpler to set up and run.

54 ENVIRONMENTAL SCIENCES↗

Validation of the single-event method for low-energy electron transport via stopping power calculations with $\mathrm{MCNP}$

Monte Carlo simulations of low-energy ( <50 keV) electron transport in matter are essential for a broad range of application fields. Several Monte Carlo codes have developed specialized treatments for this case, but a comprehensive validation of low-energy electron transport for general-purpose simulations remains lacking in the literature. One approach to accomplish this validation is calculation of stopping power using low-energy electron transport physics, as stopping power is a fundamental radiation transport quantity which must be simulated accurately for nearly any application. Here in this work, we use the Monte Carlo N-Particle (MCNP) radiation transport code with the single-event method for electron transport to calculate stopping powers of low-energy electrons (50 eV to 30 keV) in 41 elemental solids, 14 compound solids, and five rare gas solids, comparing simulation results to published semi-empirical stopping power calculations from optical measurements. In general, the simulations give good agreement (typically within ±10%) with semi-empirical stopping power values at higher energies: 300 eV and above for most elemental solids, 1 keV and above for compound solids, and 400 eV and above for rare gas solids. Agreement between MCNP and semi-empirical values is worse below these energies. The most significant source of error is the EPRDATA14 cross section data, which does not account for changes in electronic structure due to solid-state bonding, particularly in compound materials. The simplistic model of atomic excitation used to generate the EPRDATA14 cross sections is another key source of error. Additionally, the breakdown of the continuous slowing-down approximation introduces significant uncertainty at low energies, although this is a limitation of the calculation method and not of the simulation procedure. Accounting for these and other uncertainty sources, the single event method in MCNP is robust and able to give good accuracy for a variety of low-energy electron transport problems through diverse kinds of materials.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Improvement and modification of the routing system for the health-care waste collection and transportation in Istanbul

Handling of health-care wastes is among the most important environmental problems in Turkey as it is in the whole world. Approximately 25-30 tons of health-care wastes, in addition to the domestic and recyclable wastes, are generated from hospitals, clinics and other small health-care institutions daily on the European and the Asian sides of Istanbul [Kocasoy, G., Topkaya, B., Zeren, B.A., Kilic, M., et al., 2004. Integrated Health-care Waste Management in Istanbul, Final Report of the LIFE00 TCY/TR/054 Project, Turkish National Committee on Solid Wastes, Istanbul, Turkey; Zeren, B.A., 2004. The Health-care Waste Management of the Hospitals in the European Side of Istanbul, M.S. Thesis, Bogazici University, Istanbul, Turkey; Kilic, M., 2004. Determination of the Health-care Waste Handling and Final Disposal of the Infected Waste of Hospital-Medical Centers in the Anatolian Side of Istanbul. M.S. Thesis, Bogazici University, Istanbul, Turkey]. Unfortunately, these wastes are not handled, collected or temporarily stored at the institutions properly according to the published Turkish Medical Waste Control Regulation [Ministry of Environment and Forestry, 2005. Medical Waste Control Regulation. Official Gazette No. 25883, Ankara, Turkey]. Besides the inappropriate handling at the institutions, there is no systematic program for the transportation of the health-care wastes to the final disposal sites. The transportation of these wastes is realized by the vehicles of the municipalities in an uncontrolled, very primitive way. As a consequence, these improperly managed health-care wastes cause many risks to the public health and people who handle them. This study has been conducted to develop a health-care waste collection and transportation system for the city of Istanbul, Turkey. Within the scope of the study, the collection of health-care wastes from the temporary storage rooms of the health-care institutions, transportation of these wastes to the final disposal areas and the cost-benefit analyses of the existing and the proposed optimum transportation routes are investigated and the most feasible routes from the point of view of efficiency and economy have been determined. In order to solve the scheduling and route optimization problem, special software programs called MapInfo and Roadnet were used. For the program, the geocodes of hospital locations, data about the amount of the health-care wastes generated, the loading and unloading process times, and the capacity of the collecting vehicles were taken into account. The new systems developed aim at the daily collection of the health-care wastes from the institutions and their transportation directly to the final disposal area/facility by using the shortest and the most efficient routes to resolve the routing and scheduling problem and to reduce the cost arising from the transportation.

54 ENVIRONMENTAL SCIENCES↗

Water-Assisted Proton Transport in Confined Nanochannels

Hydrated excess protons under hydrophobic confinement are a critical component of charge transport behavior and reactivity in nanoporous materials and biomolecular systems. In this study, excess proton confinement effects are computationally investigated for sub-2 nm hydrophobic nanopores by varying the diameters (d = 0.81, 0.95, 1.09, 1.22, 1.36, 1.63, and 1.90 nm), lengths (l ~3 and ~5 nm), curvature, and chirality of cylindrical carbon nanotube (CNT) nanopores. CNTs with a combination of different diameter segments are also explored. The spatial distribution of water molecules under confinement is diameter-dependent; however, proton solvation and transport are consistently found to occur in the water layer adjacent to the pore wall, showing an “amphiphilic” character of the hydrated excess proton hydronium-like structure. The proton transport free energy barrier also decreases significantly as the nanopore diameter increases and proton transport becomes almost barrierless in the d > 1 nm nanopores. Among the nanopores studied, the Zundel cation (H 5 O 2 + ) is populated only in the d = 0.95 nm CNT (7,7) nanopore. The presence of the hydrated excess proton and K + inside the CNT (7,7) nanopore induces a water density increase by 40 and 20%, respectively. The K + transport through CNT nanopores is also consistently higher in the free energy barrier than proton transport. Interestingly, the evolution of excess protonic charge defect distribution reveals a “frozen” single water wire configuration in the d = 0.81 nm CNT (6,6) nanopore (or segment), through which hydrated excess protons can only shuttle via the Grotthuss mechanism. Vehicular diffusion becomes relevant to proton transport in the “flat” free energy regions and in the wider nanopores, where protons do not primarily shuttle in the axial direction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Probing the Fine Symmetry Breaking in High-Temperature Superconductor Bi 2 Sr 2 CaCu 2 O 8+δ with Angle-Resolved Nonreciprocal Transport

After decades of research, symmetry breaking in high-temperature cuprate superconductors remains a key issue to resolve and is relevant to understanding their exotic quantum phases. In the prototypical cuprate superconductor, Bi 2 Sr 2 CaCu 2 O 8+δ (Bi2212), the possible symmetry breaking has been mostly examined microscopically with scanning tunneling microscopy and photoemission spectroscopy. However, macroscopic evidence and the direct implications for electronic transport have remained elusive. Using superconductivity-enhanced nonreciprocal transport, we report macroscopic evidence of inversion symmetry breaking in Bi2212. While the inversion symmetry breaking is subtle, its effect on nonreciprocal transport is significantly enhanced by the vortex motion during the superconducting transition, leading to a robust manifestation of inversion symmetry breaking in macroscopic transport. Combining angle-resolved nonreciprocal transport and 3D tight-binding model calculations, we derive that the inversion symmetry breaking is due to subtle crystal distortions that give rise to both in-plane and out-of-plane polar axes. Our work not only establishes nonreciprocal transport as a sensitive macroscopic probe to provide electrical transport-based evidence of fine symmetry breaking in Bi2212, but also paves the way for novel device applications such as high-temperature superconducting diodes and superconducting spintronics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Polaron Delocalization and Transport in Doped Graphene Nanoribbon Thin Films

Graphene nanoribbons (GNRs) are quantum-confined π-conjugated monolayer semiconductors with attractive properties for optoelectronic applications. However, the ground- and excited-state properties of charge carriers in GNRs are still poorly understood, particularly with regards to the coupling between charges and the GNR lattice and the degree to which this coupling impacts local and macroscopic charge transport. To address this issue, we systematically correlate carrier density-dependent charge transport with spectroscopic modulations in chemically doped thin films of armchair graphene nanoribbons (9-aGNRs). This study combines Fourier transform infrared (FTIR) and ultraviolet−visible−near-infrared (UV−vis−NIR) spectroscopy with both local and macroscopic conductivity measurements to arrive at a full and self-consistent picture of transport in doped GNR thin films. Using three different molecular p-type dopants (i.e., oxidants), we demonstrate that hole polarons are the dominant quasi-particle determining charge transport in GNRs and that the degree of polaron delocalization depends sensitively on the dopant and the hole density. For all three dopants, the local conductivity probed by microwave spectroscopy substantially exceeds the long-range conductivity obtained by four-point probe measurements. Interestingly, the dopant size substantially influences charge transport at high hole densities. We ascribe this effect to different propensities for forming bipolarons with lower mobilities than polarons. Comparison of GNR transport and spectral properties to other prototypical π-conjugated semiconductors (e.g., semiconducting polymers or carbon nanotubes) benchmark the charge transport properties of GNR thin films for optoelectronic devices and applications.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Does Water Content or Flow Rate Control Colloid Transport in Unsaturated Porous Media?

Mobile colloids can play an important role in contaminant transport in soils: many contaminants exist in colloidal form, and colloids can facilitate transport of otherwise immobile contaminants. In unsaturated soils, colloid transport is, among other factors, affected by water content and flow rate. Our objective was to determine whether water content or flow rate is more important for colloid transport. We passed negatively charged polystyrene colloids (220 nm diameter) through unsaturated sand-filled columns under steady-state flow at different water contents (effective water saturations Se ranging from 0.1 to 1.0, with Se = (? – ?r)/(?s – ?r)) and flow rates (pore water velocities v of 5 and 10 cm/min). Water content was the dominant factor in our experiments. Colloid transport decreased with decreasing water content, and below a critical water content (Se < 0.1), colloid transport was inhibited, and colloids were strained in water films. Pendular ring and water film thickness calculations indicated that colloids can move only when pendular rings are interconnected. The flow rate affected retention of colloids in the secondary energy minimum, with less colloids being trapped when the flow rate increased. These results confirm the importance of both water content and flow rate for colloid transport in unsaturated porous media and highlight the dominant role of water content.

99 GENERAL AND MISCELLANEOUS↗

Continuous time random walk analysis of solute transport in fractured porous media

The objective of this work is to discuss solute transport phenomena in fractured porous media, where the macroscopic transport of contaminants in the highly permeable interconnected fractures can be strongly affected by solute exchange with the porous rock matrix. We are interested in a wide range of rock types, with matrix hydraulic conductivities varying from almost impermeable (e.g., granites) to somewhat permeable (e.g., porous sandstones). In the first case, molecular diffusion is the only transport process causing the transfer of contaminants between the fractures and the matrix blocks. In the second case, additional solute transfer occurs as a result of a combination of advective and dispersive transport mechanisms, with considerable impact on the macroscopic transport behavior. We start our study by conducting numerical tracer experiments employing a discrete (microscopic) representation of fractures and matrix. Using the discrete simulations as a surrogate for the 'correct' transport behavior, we then evaluate the accuracy of macroscopic (continuum) approaches in comparison with the discrete results. However, instead of using dual-continuum models, which are quite often used to account for this type of heterogeneity, we develop a macroscopic model based on the Continuous Time Random Walk (CTRW) framework, which characterizes the interaction between the fractured and porous rock domains by using a probability distribution function of residence times. A parametric study of how CTRW parameters evolve is presented, describing transport as a function of the hydraulic conductivity ratio between fractured and porous domains.

54 ENVIRONMENTAL SCIENCES↗

Characterizing the Influence of Fracture Density on Network Scale Transport

The topology of natural fracture networks is inherently linked to the structure of the fluid velocity field and transport therein. Here we study the impact of network density on flow and transport behaviors. We stochastically generate fracture networks of varying density and simulate flow and transport with a discrete fracture network model, which fully resolves network topology at the fracture scale. We study conservative solute trajectories with Lagrangian particle tracking and find that as fracture density decreases, solute channelization to large local fractures increases, thereby reducing plume spreading. Furthermore, in sparse networks mean particle travel distance increases and local network features, such as velocity zones where flow is counter to the primary pressure gradient, become increasingly important for transport. As the network density increases, network statistics homogenize and such local features have a reduced impact. We quantify local topological influence on transport behavior with an effective tortuosity parameter, which measures the ratio of total advective distance to linear distance at the fracture scale; large tortuosity values are correlated to slow-velocity regions. Additionally, these large tortuosity, slow-velocity regions delay downstream transport and enhance tailing on particle breakthrough curves. Finally, we predict transport with an upscaled, Bernoulli spatial Markov random walk model and parameterize local topological influences with a novel tortuosity parameter. Furthermore, Bernoulli model predictions improve when sampling from a tortuosity distribution, as opposed to a fixed value as has previously been done, suggesting that local network topological features must be carefully considered in upscaled modeling efforts of fracture network systems.

58 GEOSCIENCES↗

A Multicomponent Reactive Transport Model for Integrated Surface‐Subsurface Hydrology Problems

Abstract Despite the widespread use of integrated hydrology models in a variety of applications, consideration of multicomponent reactive transport is still not common. The implementation of these processes requires coupling transport at the surface‐subsurface interface and efficient solution of the non‐linear geochemical model that is consistent with the integrated hydrology solution. The Advanced Terrestrial Simulator provides a flexible multiphysics framework that facilitated this process. In this work, the integrated reactive transport process kernel (PK) was weakly coupled to the integrated hydrology PK. In turn, integrated transport and reactions were coupled using an operator splitting approach. This splitting enabled an explicit solution of the integrated transport problem, including a novel algorithm to calculate exchange fluxes across the surface‐subsurface interface and a point‐by‐point solution of the geochemical problem. Geochemical capabilities were added using well‐established external codes, but rather than using a custom interface to each, a generic interface was used that clearly specifies the variables and operations used by the chemistry PK. The implementation is demonstrated with two example simulations: transport of a tracer in a soil column as it saturates over time and water ponds on the surface and reactive transport in a hillslope driven by successive wet‐dry cycles that result in infiltration, runoff and exfiltration processes.

54 ENVIRONMENTAL SCIENCES↗

Molecular transport enhancement in pure metallic carbon nanotube porins

Nanofluidic channels impose extreme confinement on water and ions, giving rise to unusual transport phenomena strongly dependent on the interactions at the channel–wall interface. Yet how the electronic properties of the nanofluidic channels influence transport efficiency remains largely unexplored. Here we measure transport through the inner pores of sub-1 nm metallic and semiconducting carbon nanotube porins. We find that water and proton transport are enhanced in metallic nanotubes over semiconducting nanotubes, whereas ion transport is largely insensitive to the nanotube bandgap value. Molecular simulations using polarizable force fields highlight the contributions of the anisotropic polarizability tensor of the carbon nanotubes to the ion–nanotube interactions and the water friction coefficient. We also describe the origin of the proton transport enhancement in metallic nanotubes using deep neural network molecular dynamics simulations. Finally, these results emphasize the complex role of the electronic properties of nanofluidic channels in modulating transport under extreme nanoscale confinement.

77 NANOSCIENCE AND NANOTECHNOLOGY↗