Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STRESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74

Comparison of Multi-Scale Nonlinear and Conventional Linear Methods for Stress Analysis of Nb 3 Sn Superconducting Magnets

Here this is an extension of the work on a multi-scale nonlinear procedure that demonstrated how to conduct nonlinear stress analysis of Nb 3 Sn superconducting accelerator magnets. The nonlinear procedure uses measured stress-strain curves of annealed copper, Nb 3 Sn strands and coil samples as inputs, which reduces the number of assumptions made for material properties—key uncertainties of any engineering analysis. The results from nonlinear analysis, semi-nonlinear analysis, and linear analysis of the same QFFB2 Nb 3 Sn quadrupole magnet under the same temperature and loads, were compared and discussed. The comparison illustrates that nonlinear stress analysis is significantly more accurate than other methods. As the superconducting coil block is a complex, composite material, it would be inadequate to assume the whole coil block to be linear, either isotropic or orthotropic. It is imperative to conduct nonlinear analysis by simulating the superconducting coil to the level of detail of the individual cables and individual strands. The nonlinear stress analysis procedure can be used to simulate not only Nb 3 Sn magnets, but also NbTi and HTS magnets.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Pore-scale investigation on stress-dependent characteristics of granular packs and the impact of pore deformation on fluid distribution

Understanding the effect of changing stress conditions on multiphase flow in porous media is of fundamental importance for many subsurface activities including enhanced oil recovery, water drawdown from aquifers, soil confinement, and geologic carbon storage. Geomechanical properties of complex porous systems are dynamically linked to flow conditions, but their feedback relationship is often oversimplified due to the difficulty of representing pore-scale stress deformation and multiphase flow characteristics in high fidelity. In this work, we performed pore-scale experiments of single- and multiphase flow through bead packs at different confining pressure conditions to elucidate compaction-dependent characteristics of granular packs and their impact on fluid flow. A series of drainage and imbibition cycles were conducted on a water-wet, soda-lime glass bead pack under varying confining stress conditions. Simultaneously, X-ray micro-CT was used to visualize and quantify the degree of deformation and fluid distribution corresponding with each stress condition and injection cycle. Micro-CT images were segmented using a gradient-based method to identify fluids (e.g., oil and water), and solid phase redistribution throughout the different experimental stages. Changes in porosity, tortuosity, and specific surface area were quantified as a function of applied confining pressure. Results demonstrate varying degrees of sensitivity of these properties to confining pressure, which suggests that caution must be taken when considering scalability of these properties for practical modeling purposes. Changes in capillary number with confining pressure are attributed to the increase in pore velocity as a result of pore contraction. Furthermore, this increase in pore velocity was found to have a marginal impact on average phase trapping at different confining pressures.

58 GEOSCIENCES↗

Experimental determination of the stress evolution in a prebent steel very high-performance concrete beam by means of an active stressmeter

ConclusionsThis experimental research allowed to emphasize two main factors for the quality of the measurements by active stress-meters: on one hand, the accuracy of the location and the orientation of the jacks considering the severe conditions during the casting and in contrast, and the reliability with time of the embedded strain gages considering the possible presence of important electric disturbances in the environment. However, during 4 months, the quality of the strain signals used for the control turned out satisfactory and the obtained values are close to the theoretical computation. The evolution of the pressure during the same period shows a good regularity and a good agreement between the measurements and the values computed by the two-function method using the CEB-MC90 model code in its 1999 version for the prediction of concrete creep and shrinkage{sup 11} and the model of Yue and Taerwe{sup 10} for the creep recovery law (maximal difference of only 0.6 MPa after 4 months of recording). The aim of the direct measurement of stresses can be considered as reached, the prediction of the stress state in the beam according to the two-function method being validated with a precision of ±1.5% (uncertainty of about 1 MPa for a devise designed for a stress range up to 35 MPa).

42 ENGINEERING↗

Core-drilling technique for in-situ stress evaluation in concrete structures

SummaryFor assessing the existing stresses in distressed reinforced concrete/prestressed concrete structures, the concrete core-drilling technique can be used. This core-drilling technique is a stress measurement technique in which a small core is drilled on the structure and the strain perturbations around the core are measured by instrumenting strain gages aligned in the same direction. Laboratory studies were conducted to evaluate the reliability of this concrete core-drilling technique. Calibration coefficients were evaluated experimentally for the used gage length, location, and configuration. Comparison was also made with coefficients evaluated theoretically. This technique is suitable for prestressed concrete girders where girders are prestressed in one direction (longitudinally). Also in reinforced concrete members like columns, compression zones of beams on the major bending axis (along the span) can be evaluated for their in-situ stresses. This concrete core-drilling technique can be used to determine the in-situ stress with enhanced sensitivity in “in-service” prestressed concrete structures.

36 MATERIALS SCIENCE↗

Grayscale Digital Light Processing Gradient Printing for Stress Concentration Reduction and Material Toughness Enhancement

Avoiding stress concentrations is essential to achieve robust parts since failure tends to originate at such concentrations. With recent advances in multimaterial additive manufacturing, it is possible to alter the stress (or strain) distribution by adjusting the material properties in selected locations. Here, we investigate the use of grayscale digital light processing (g-DLP) 3D printing to create modulus gradients around areas of high stress. These gradients prevent failure by redistributing high stresses (or strains) to the neighboring material. The improved material distributions are calculated using finite element analysis. The much-enhanced properties are demonstrated experimentally for thin plates with circular, triangular, and elliptical holes. In conclusion, this work suggests that multimaterial additive manufacturing techniques like g-DLP printing provide a unique opportunity to create tougher engineering materials and parts.

36 MATERIALS SCIENCE↗

Thermomechanical Stress and Creep-Fatigue Analysis of a High-Temperature Prototype Receiver for Heating Particles

This work presents a three-dimensional (3D) thermomechanical model of a prototype-scale enclosed light trapping solar receiver for heating particles. Results of the thermoelastic model are used to estimate receiver lifetime under maximum flux conditions. A computational fluid dynamics (CFD) model is first developed to predict the temperature fields in a multi-panel assembly under steady operating conditions. Solar flux distributions on the receiver are obtained from the software package SolTrace and applied to the 3D thermal model. The subsequent particle heating is captured through a simplified 1D energy balance. Panel reradiation is considered through a surface-to-surface radiation model and natural convection loss to the surrounding air is captured in a representative fluid domain surrounding the receiver. The resulting temperature fields from the CFD analysis are used as inputs for a thermoelastic mechanical model with representative boundary conditions. With the resultant temperature and stress fields, a creep-fatigue damage and lifetime analysis is performed using the linear damage accumulation (LDA) theory. The Manson-Coffin formula and Larson Miller correlation are used to calculate the fatigue and creep, respectively. A maximum damage (corresponding to a 30-year service life) is defined for design assessment. The model was first developed and verified in detail by comparing with published results in the literature (temperature and stress profiles and distributions, and creep/fatigue damage fractions) for tubular solar receivers with supercritical carbon dioxide as the working fluid. It was then implemented to model a planar-cavity receiver with various design parameters. Specifically, three different design geometries are considered, and the results show that a maximum temperature of approximately 1200 K could be reached for each design with the given incident solar flux, with the main difference being the distribution of these temperatures. Preliminary resulting stresses for the small-scale prototype without design optimization vary from 20 MPa to 250 MPa for each design, with the maximum stresses occurring on the front face and concave geometry on the side of the panel. In future work, the developed methodology shown here will be applied to analyze a full-scale (50-150 MWth) receiver.

concentrated solar power↗

Critical Shear Stress for Erosion Under Laminar Jet Flow

Particle erosion is an important process in both natural and manmade environments. For example, in natural environments particle or sediment erosion rates determine the course of rivers, depth of streams, and fate of deltas. The interplay between erosion rates and flow patterns can have dramatic impact on shorelines. Where hydrodynamic jet flows or rip currents change direction, sediments may accumulate or disperse altering the shape of coastlines and the ecosystems and economies that rely on them. In man-made systems, jet flows may be used to mobilize particles from surfaces or within industrial scale mixing tanks. For example, in the nuclear industry, impinging jet mixers may be used to mobilize and suspend sludges at the bottom of waste tanks. In each of these examples, the Shields diagram is useful to determine the conditions under which erosion occurs. This diagram plots the scaled critical shear stress for erosion as a function of the particle size as embedded in particle Reynolds numbers, Archimedes numbers, or their equivalents. Although the data, that carries a large spread, is largely in agreement with mathematical models, for the smallest particles, model predictions diverge from each other and from experimental data. Indeed, there is substantial uncertainty about the Shields diagrams at relatively small particle sizes and flow rates. Here we evaluate critical shear stresses for erosion under laminar jet flow. To date critical shear stresses for erosion, as embodied in Shields diagrams, have largely been developed for turbulent flow both experimental and mathematically. However, curves on the Shields diagrams diverge among various models at lower particle Reynolds numbers. Indeed, how critical shear stresses for erosion develop under fully laminar jet flow conditions (not simply laminar boundary layers under turbulent flow) remains unclear. Here we address this gap, which is particularly important for mobilization of the smallest particles. We find the Shields parameter to be inversely proportional to the particle Reynolds numbers under laminar jet flow conditions similar to turbulent conditions.

critical shear stresses, erosion rates, effective ↗

TECHNICAL BACKGROUND FOR THE UPDATE AND EXTENSION OF THE TIME-DEPENDENT ALLOWABLE STRESSES OF TYPE 304H AND 316H STAINLESS STEELS

Type 304H and 316H stainless steels are codified in the ASME Boiler and Pressure Vessel Code for Section III, Division 5, Class A construction for up to 1500F (816C) and 300,000 hours. Extension of the design lifetimes to 500,000 hours has been undertaken by various research projects and by the ASME Section III, Division 5 Code Committees. Due to a long-standing issue related to non-classical creep behavior on the use of the time to the onset of tertiary creep as one of the time-dependent allowable stress criteria, little progress was made in the extension of the time-dependent allowable stresses for Type 304H and 316H stainless steels. A recent effort by Dabrow and Nestell (Impact of Tertiary Creep on Time Dependent Allowable Stresses for Type 304H and 316H Stainless Steels, Report 0300-0003-RPT-001, MPR Associates, Alexandria, VA, 2020) has provided a rational method for the treatment of the highly variable data for the time to onset of tertiary creep. In this paper, the background formulas for determining the time-dependent allowable stress values of Type 304H and 316H stainless steels, as assembled from relevant project work, are presented. These updates and extensions are being recommended to the ASME Code committees for approval, and are subject to change upon feedback from ASME Section III Code committees.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Novel strategy for low-temperature, high-rate growth of dense, hard, and stress-free refractory ceramic thin films

Growth of fully dense refractory thin films by means of physical vapor deposition (PVD) requires elevated temperatures T{sub s} to ensure sufficient adatom mobilities. Films grown with no external heating are underdense, as demonstrated by the open voids visible in cross-sectional transmission electron microscopy images and by x-ray reflectivity results; thus, the layers exhibit low nanoindentation hardness and elastic modulus values. Ion bombardment of the growing film surface is often used to enhance densification; however, the required ion energies typically extract a steep price in the form of residual rare-gas-ion-induced compressive stress. Here, the authors propose a PVD strategy for the growth of dense, hard, and stress-free refractory thin films at low temperatures; that is, with no external heating. The authors use TiN as a model ceramic materials system and employ hybrid high-power pulsed and dc magnetron co-sputtering (HIPIMS and DCMS) in Ar/N{sub 2} mixtures to grow dilute Ti{sub 1−x}Ta{sub x}N alloys on Si(001) substrates. The Ta target driven by HIPIMS serves as a pulsed source of energetic Ta{sup +}/Ta{sup 2+} metal–ions, characterized by in-situ mass and energy spectroscopy, while the Ti target operates in DCMS mode (Ta-HIPIMS/Ti-DCMS) providing a continuous flux of metal atoms to sustain a high deposition rate. Substrate bias V{sub s} is applied in synchronous with the Ta-ion portion of each HIPIMS pulse in order to provide film densification by heavy-ion irradiation (m{sub Ta} = 180.95 amu versus m{sub Ti} = 47.88 amu) while minimizing Ar{sup +} bombardment and subsequent trapping in interstitial sites. Since Ta is a film constituent, primarily residing on cation sublattice sites, film stress remains low. Dense Ti{sub 0.92}Ta{sub 0.08}N alloy films, 1.8 μm thick, grown with T{sub s} ≤ 120 °C (due to plasma heating) and synchronized bias, V{sub s} = 160 V, exhibit nanoindentation hardness H = 25.9 GPa and elastic modulus E = 497 GPa compared to 13.8 and 318 GPa for underdense Ti-HIPIMS/Ti-DCMS TiN reference layers (T{sub s} < 120 °C) grown with the same V{sub s}, and 7.8 and 248 GPa for DCMS TiN films grown with no applied bias (T{sub s} < 120 °C). Ti{sub 0.92}Ta{sub 0.08}N residual stress is low, σ = −0.7 GPa, and essentially equal to that of Ti-HIPIMS/Ti-DCMS TiN films grown with the same substrate bias.

36 MATERIALS SCIENCE↗

OxyR regulates the oxidative stress response in Zymomonas mobilis during oxic growth and anoxic biofuel fermentation

The bacterium Zymomonas mobilis is widely studied for its potential as an industrial biofuel producer. Anoxic fermentation by Z. mobilis in lignocellulosic hydrolysate can generate bioethanol from renewable plant biomass. In this study, we deleted a gene from the Z. mobilis genome encoding a homolog of OxyR, a transcription factor that activates an oxidative stress response in bacteria to reduce reactive oxygen species (ROS). Deletion of this transcription factor inhibited growth of Z. mobilis in oxic, but not anoxic, conditions in laboratory media. A ROS probe revealed that the oxyR response is required to reduce intracellular ROS during oxic growth. Importantly for biofuel production, the absence of oxyR inhibited growth and delayed ethanol production during anoxic hydrolysate fermentation. To determine the source of oxidative stress in hydrolysates, we grew ΔoxyR in a synthetic hydrolysate containing known inhibitors found in hydrolysates. There was no growth defect in ΔoxyR in the synthetic hydrolysate, indicating that known inhibitory compounds are not the source of anoxic oxidative stress. We determined that ammonia-fiber expansion switchgrass hydrolysate contains significant peroxide concentrations. Addition of catalase to hydrolysate improves growth of both ΔoxyR and wild-type Z. mobilis in hydrolysate. This study uncovers an important source of stress to Z. mobilis during biofuel fermentation.

OxyR↗

Shallow-donor lasers in uniaxially stressed silicon

The effects of the terahertz-stimulated emission of Group-V donors (phosphorus, antimony, arsenic, bismuth) in uniaxially stressed silicon, excited by CO{sub 2} laser radiation are experimentally studied. It is shown that uniaxial compressive stress of the crystal along the [100] direction increases the gain and efficiency of stimulated radiation, significantly decreasing the threshold pump intensity. The donor frequencies are measured and active transitions are identified in stressed silicon. The dependence of the residual population of active donor states on the uniaxial compressive stress along the [100] direction is theoretically estimated.

36 MATERIALS SCIENCE↗

Terahertz absorption and emission upon the photoionization of acceptors in uniaxially stressed silicon

Experimental data on the spontaneous emission and absorption modulation in boron-doped silicon under CO{sub 2} laser excitation depending on the uniaxial stress applied along the [001] and [011] crystallographic directions are presented. Room-temperature radiation is used as the probe radiation. Low stress (less than 0.5 kbar) is shown to reduce losses in the terahertz region by 20%. The main contribution to absorption modulation at zero and low stress is made by A{sup +} centers. Intersubband free hole transitions additionally contribute to terahertz absorption at higher stress. These contributions can be minimized by compensation.

36 MATERIALS SCIENCE↗

Energy Expenditure Upon the Formation of the Elastically Stressed State in the Layers of a Step-Graded Metamorphic Buffer in a Heterostructure Grown on a (001) GaAs Substrate

On the basis of data on X-ray structural analysis performed by the method of reciprocal-space mapping and investigations using secondary-ion mass spectrometry and transmission electron microscopy, it is shown that vertical compressive stresses also arise in a multilayer epitaxial heterostructure comprised of a step-graded metamorphic buffer along with lateral compressive stresses. The cause of the appearance of vertical stresses is the effect of interlayer hardening, which arises due to the deceleration of fragments of glide dislocations by interphase boundaries. Analysis performed within the framework of the linear theory of elasticity shows that the elastically stressed state of the buffer steps is similar to the state that can be achieved as a result of a two-stage deformation process: bulk and biaxial compression. Bulk compression leads to large energy expenditures in the formation of the structure of the buffer steps, which is reflected, in particular, in violation of the coherence between the dislocation-free and the underlying layers.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Identification of stress biomarkers for drought and increased soil temperature in seedlings of European beech ( Fagus sylvatica )

Drought is an environmental stress that impacts plant productivity. Projections show both an increase in intense rain events and a reduction in the number of rain days, conditions that leads to increased risk of drought. Consequently, the identification of molecular biomarkers suitable for evaluating the impact of water deprivation conditions on forest plant seedlings is of significant value for monitoring purposes and forest management. In this study, we evaluated a biochemical methodology for the assessment of drought stress coupled with variable soil temperature in European beech (Fagus sylvatica L.) seedlings by analyzing a set of metabolites and enzymes involved in free radical scavenging and cell wall synthesis. The results indicate that the specific activities and isoform profile of superoxide dismutases and glutathione peroxidases together with the variation of phenolic compounds enable discrimination between seedlings with different degrees of photosynthetic activity. This approach represents a promising platform for the assessment of drought stress in forest trees and could serve for enhancing selection and breeding practices, allowing for plants that are more tolerant of abiotic stress.

beach↗

Numerical Solution of Moving Phase Boundary and Diffusion-Induced Stress of Sn Anode in the Lithium-Ion Battery

Here, we have previously observed a large transient stress in Sn film anodes at the beginning of the Sn-Li 2 Sn 5 phase transformation. To understand this behavior, we use numerical modeling to simulate the kinetics of the 1-D moving boundary and Li diffusion in the Sn anodes. A mixture of diffusion-controlled and interface-controlled kinetics is found. The Li concentration in the Li 2 Sn 5 phase remains near a steady-state profile as the phase boundary propagates, whereas the Li diffusion in Sn is more complicated. Li continuously diffuses into the Sn layer and produces a supersaturation; the Li can then diffuse toward the Sn/Li 2 Sn 5 interface and contribute to further phase transformation. Finally, the evolution of Li concentration in the Sn induces strain which involves rate-dependent plasticity and elastic unloading, resulting in the complex stress evolution that is observed. In the long term, the measured stress is dominated by the stress in the growing Li 2 Sn 5 phase.

25 ENERGY STORAGE↗

The Role of Back Pressure in the Atmospheric Response to Surface Stress Induced by the Kuroshio

Abstract The effect of ocean current drag on the atmosphere is of interest as a test case for the role of back pressure, because the response is independent of the thermally induced modulation of the boundary layer stability and hydrostatic pressure. The authors use a regional atmospheric model to investigate the impact of drag induced by the Kuroshio in the East China Sea on the overlying winter atmosphere. Ocean currents dominate the wind stress curl compared to the impacts of sea surface temperature (SST) fronts. Wind stress convergences and divergences are weakly enhanced even though the ocean current is almost geostrophic. These modifications change the linear relationships (coupling coefficients) between the wind stress curl/divergence and the SST Laplacian, crosswind, and downwind gradients. Clear signatures of the ocean current impacts are found beyond the sea surface: sea surface pressure (back pressure) decreases near the current axis, and precipitation increases over the downwind region. However, these responses are very small despite strong Ekman pumping due to the current. A linear reduced gravity model is used to explain the boundary layer dynamics. The linear vorticity equation shows that the oceanic influence on wind stress curl is balanced by horizontal advection decoupling the boundary layer from the interior atmosphere. Spectral transfer functions are used to explain the general response of back pressure to geostrophic ocean currents and sea surface height.

54 ENVIRONMENTAL SCIENCES↗

Determination of residual stress in a microtextured α titanium component using high-energy synchrotron X-rays

A shrink-fit sample is manufactured with a Ti-8Al-1Mo-1V alloy to introduce a multiaxial residual stress field in the disk of the sample. A set of strain and orientation pole figures are measured at various locations across the disk using synchrotron high-energy X-ray diffraction. Two approaches—the traditional sin 2 Ψ method and the bi-scale optimization method—are taken to determine the stresses in the disk based on the measured strain and orientation pole figures, to explore the range of solutions that are possible for the stress field within the disk. While the stress components computed using the sin 2 Ψ method and the bi-scale optimization method have similar trends, their magnitudes are significantly different. Lastly, it is suspected that the local texture variation in the material is the cause of this discrepancy.

42 ENGINEERING↗

Reduced yield stress for zirconium exposed to iodine: Reactive force field simulation

Iodine-induced stress-corrosion cracking (ISCC), a known failure mode for nuclear fuel cladding, occurs when iodine generated during the irradiation of a nuclear fuel pellet escapes the pellet through diffusion or thermal cracking and chemically interacts with the inner surface of the clad material, inducing a subsequent effect on the cladding’s resistance to mechanical stress. To complement experimental investigations of ISCC, a reactive force field (ReaxFF) compatible with the Zr-I chemical and materials systems has been developed and applied to simulate the impact of iodine exposure on the mechanical strength of the material. The study shows that the material’s resistance to stress (as captured by the yield stress of a high-energy grain boundary) is related to the surface coverage of iodine, with the implication that ISCC is the result of adsorption-enhanced decohesion.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗