Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STALLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74

A performance application study of a jet-flap helicopter rotor

A performance study was made of the application of a jet-flap to a reaction-drive rotor for a heavy-lift helicopter mission and for a high-speed-helicopter maneuverability (200 knots, 2g) mission. The results of the study are as follows: As a result of the increase in maximum airfoil lift coefficient achieved by the jet-flap, rotor solidity is reduced with the jet-flap to approximately 59% of a nonjet-flap rotor. As a result of the saving in rotor solidity, and hence in rotor weight, the jet-flap configuration had a 21% higher productivity than a nonjet-flap configuration. Of the three propulsion systems studied utilizing a jet-flap (hot cycle, warm cycle, cold cycle) the hot cycle gave the largest increase in productivity. The 200 knot 2g mission is performed best with a warm cycle propulsion system. The jet-flap permits designing for a rotor blade loading coefficient C sub T/sigma = .170 at 2g without encountering blade stall. The jet-flap rotor permits a 200 knot 2g maneuver without suffering the penalty of an unreasonable rotor solidity that would be required by a nonjet-flap rotor.

Sullivan, R. J.↗

Performance of a single-stage transonic compressor with a blade-tip solidity of 1.3

The design and experimental performance of a 50-centimeter-diameter, single stage, axial flow, transonic compressor with a blade tip solidity of 1.3 are presented. Radial surveys were made of the flow conditions for both the rotor and stator. At design speed, peak efficiencies for both rotor and stage were 0.87 and 0.82, respectively, and occurred at an equivalent weight flow of 29.6 kilograms per second (202 kg/sec/sq m of annulus area). At peak efficiency, the total pressure ratios for both rotor and stage were 1.79 and 1.73, respectively. Stall margin for the stage was 17 percent.

Urasek, D. C.↗

Performance of a single-stage axial-flow transonic compressor stage with a blade tip solidity of 1.7

The overall and blade-element performance of a transonic compressor stage is presented over the stable operating range at rotative speeds from 50 to 100 percent of design speed. Stage peak efficiency of 0.784 was obtained at a weight flow of 28.6 kilograms per second and a pressure ratio of 1.706. Stall margin at design speed was 11.4 percent. The peak efficiency being significantly less than design efficiency was attributed to: (1) the stator loss and the radial gradient of losses being much higher than design, (2) the losses and blockages associated with the rotor part-span dampers not being incorporated into the design, and (3) mismatch of the rotor and stator badle elements.

Moore, R. D.↗

An airline study of advanced technology requirements for advanced high speed commercial transport engines. 1: Engine design study assessment

The advanced technology requirements for an advanced high speed commercial tranport engine are presented. The results of the phase 1 study effort cover the following areas: (1) statement of an airline's major objectives for future transport engines, (2) airline's method of evaluating engine proposals, (3) description of an optimum engine for a long range subsonic commercial transport including installation and critical design features, (4) discussion of engine performance problems and experience with performance degradation, (5) trends in engine and pod prices with increasing technology and objectives for the future, (6) discussion of the research objectives for composites, reversers, advanced components, engine control systems, and devices to reduce the impact of engine stall, and (7) discussion of the airline objectives for noise and pollution reduction.

Sallee, G. P.↗

Instantaneous distortion investigation

The results obtained in an inlet-engine compatibility test run in the 10x10 SWT of the NASA-Lewis Research Center are reviewed. This program was run to measure the time-variant distortions produced in a supersonic inlet and to relate a unique distortion peak, occurring in an instant of time, to the origin of stall in a compressor. The major stumbling block in this type of effort is the determination of a proper increment of time over which to average pressures before computing distortions. It is reasonable to expect that the proper averaging time is related to the particular compressor in question. The most significant point reported is that the proper averaging time may not be solely dependent on a particular compressor, and, in fact, may vary with operating conditions, even for the same inlet-engine combination.

Calogeras, J. E.↗

A summary of current research in rotor unsteady aerodynamics with emphasis on work at Langley Research Center

The basic unsteady aerodynamic environment of the rotary wing is summarized. Some of the observed trends in the state of the art are discussed. Some of the research needs that will require attention are reported. A review of a number of research investigations as a part of a joint NASA/Army rotorcraft project is presented. The research is directed toward achieving a better understanding of rotor unsteady airfoils. The investigations include: (1) rotor maneuver loads; (2) level flight and maneuver wake prediction; (3) tip-vortex flow; (4) blade-vortex interactions; (5) dynamic stall; (6) transient Mach number air loads; and (7) development of variable geometry rotors.

Ward, J. F.↗

Analysis of inlet flow distortion and turbulence effects on compressor stability

The effect of steady state circumferential total pressure distortion on the loss in compressor stall pressure ratio has been established by analytical techniques. Full scale engine and compressor/fan component test data were used to provide direct evaluation of the analysis. Specifically, since a circumferential total pressure distortion in an inlet system will result in unsteady flow in the coordinate system of the rotor blades, analysis of this type distortion must be performed from an unsteady aerodynamic point of view. By application of the fundamental aerothermodynamic laws to the inlet/compressor system, parameters important in the design of such a system for compatible operation have been identified. A time constant, directly related to the compressor rotor chord, was found to be significant, indicating compressor sensitivity to circumferential distortion is directly dependent on the rotor chord.

Melick, H. C., Jr.↗

Aerodynamic characteristics of a swept augmentor wing

A brief outline of augmentor wing research is presented and is followed by a discussion of large scale wind tunnel test results for a swept augmentor wing configuration. The results show that the augmentor wing can be applied to high speed swept wing designs with little adverse effect on either the basic performance of the augmentor or the longitudinal characteristics, including maximum lift and stall. Three lateral control devices were shown to be effective and ground effect was measured for several complete aircraft configurations.

Koenig, D. G.↗

Aerodynamic effects of five lift-fan pod arrangements on an unpowered V/STOL transport model

An investigation was conducted in the Langley V/STOL tunnel to determine the effect of longitudinally oriented wing-mounted pods on the longitudinal and lateral aerodynamic characteristics in the cruise flight condition of a high-wing V/STOL transport model. Five pod arrangements were tested - three configurations with in-line pods at 20, 40, or 60 percent semispan and two split pod configurations with rear pods at 20 percent semispan and front pods at 40 or 60 percent semispan. In general, addition of the pods to the model decreased the stability, increased the lift-curve slope, and alleviated the abrupt stall of the basic model. The configuration with pods at 20 percent semispan had an abrupt instability at 10 deg angle of attack, All the configurations had lateral stability at sideslip angles from 5 to -5 deg. Very little difference in results existed between the configurations with pods at 40 and 60 percent semispan. Of the split pod configurations, the configuration with front pods at 40 percent semispan offered the best trimmed lift and lift-induced drag characteristics at high angles of attack. The configuration with in-line pods at 40 or 60 percent semispan provided the best cruise characteristics of all the pod configurations.

Thomas, J. L.↗

Single stage evaluation of highly loaded high Mach number compressor stages. 6: Data and performance of cantilevered stator

A compressor stage with a rotor tip speed of 1600 ft/sec was tested to evaluate its performance with a cantilevered stator and a rotating inner shroud beneath the stator. Both the rotor blades and the stator vanes were composed of multiple circular arc airfoil sections. Comparison of data taken during this test of the cantilevered stator and previous tests with the same compressor and airfoil geometry in a shroud stator configuration showed only slight differences in stage performance with no significant effect on overall efficiency. However, the severity of the stator wake near the rotating hub was decreased at all flows including the near surge condition. Stall and wise open discharge corrected weight flows were the same as for the shrouded stator configuration.

Merrow, A. S.↗

Aerodynamic characteristics of a vectored-thrust V/STOL fighter in the transition speed range

A wind-tunnel investigation was conducted with a vectored-thrust V/STOL fighter configuration. The model was equipped with two nacelle-mounted vectored-thrust jet simulators and one lift-jet simulator. The vectored-thrust jet could be tested at two alternate longitudinal positions and three nozzle deflection angles. The vectored-thrust configuration with the rear nozzles showed an increase in lift and a decrease in pitching moment when compared with the forward nozzles. The rear nozzles also improve stall characteristics.

Mineck, R. E.↗

The effects on cruise drag of installing refan-engine nacelles on the McDonnell-Douglas DC-9

A high speed wind tunnel test has been conducted to determine the effect on cruise drag for installing larger JT8D Refan engine nacelles on the Douglas DC-9. Drag data and wing- and nacelle/pylon/fuselage-channel pressure data are presented. Reduced pylon spares, required to minimize effects of the nacelle installation on low-speed deep stall, were investigated. The reduce span pylons resulted in no adverse interference effects. At typical cruise Mach numbers the measured penalty for the Refan installation was less than estimated due to a favorable effect of the larger entering engine stream tube suppressing the wing upper-surface velocities with subsequent wing compressibility drag reduction. Channel pressures show no shock waves or boundary layer separations.

Callaghan, J. T.↗

Simulator evaluation of the low-speed flying qualities of an experimental STOL configuration with an externally blown flap wing or an augmentor wing

The low-speed flying qualities of an experimental STOL configuration were evaluated by using a fixed-base six-degree-of-freedom simulation. The configuration had either an externally blown flap (EBF) wing or an augmentor wing (AW). The AW configuration was investigated with two tails, one sized for the AW configuration and a larger one sized for the EBF configuration. The emphasis of the study was on the 70-knot approach task. The stability and control characteristics were compared with existing criteria. Several control systems were investigated for the normal four-engine condition and for the engine-out transient condition. Minimum control and stall speeds were determined for both the three- and four-engine operation.

Powers, B. G.↗

Aerodynamic characteristics of a swept augmentor wing

A brief outline of augmentor wing research sponsored by Ames Research Center is presented and is followed by a discussion of large-scale wind-tunnel test results for a swept augmentor wing configuration. The results showed that the augmentor wing could be applied to high-speed swept wing designs with little adverse effect on either the basic performance of the augmentor or the longitudinal characteristics, including maximum lift and stall. Three lateral control devices were shown to be effective and ground effect was measured for several complete aircraft configurations.

Koenig, D. G.↗

Performance of a single-stage transonic compressor with a blade-tip solidity of 1.5 and comparison with 1.3 and 1.7 solidity stages

The overall and blade-element performance of a transonic compressor stage with a tip solidity of 1.5 is presented over the stable operating range at rotative speeds from 50 to 100 percent of design speed. State peak efficiency of 0.82 was obtained at a weight flow of 29.4 kg.sec (200.4 (kg/sec)/m2 of annulus area) and a pressure ratio of 1.71. Stall margin at design speed was 14 percent. A comparison of three stages in a solidity study showed that the performance of the 1.5 solidity stage and the 1.3 solidity stage were nearly identical but that the performance of the 1.7 solidity stage was significantly lower.

Osborn, W. M.↗

The results of low-speed wind tunnel tests to investigate the effects of the NASA refan JT8D engine nacelles on the stability and control characteristics of the Boeing 727-200

The results from two low-speed wind tunnel tests of the Boeing 727-200 airplane as configured with the NASA refan JT8D-109 turbofan engines are presented. The objective of these tests was to determine the effects of the refan installation on the low-speed stability and control characteristics of the 727 airplane. Four side nacelle locations were tested to insure that aerodynamic interactions of the nacelles and empennage would be optimized. The optimum location was judged to be the same as that of the production JT8D-9 engines; the current production engine mounts can be used for this location. Some small changes in the basic airplane characteristics are attributable to the refan nacelles. The flaps up longitudinal and lateral-directional stability are both slightly increased for low angles of attack and sideslip respectively. The longitudinal stability at stall is improved for both the flaps up and landing flap configurations. The high attitude characteristics of the basic airplane are not significantly altered by the refan nacelle installation. Directional control capability is not affected by the refan nacelles.

Shirkey, M. D.↗

Canard-wing lift interference related to maneuvering aircraft at subsonic speeds

An investigation was conducted at Mach numbers of 0.7 and 0.9 to determine the lift interference effect of canard location on wing planforms typical of maneuvering fighter configurations. The canard had an exposed area of 16.0 percent of the wing reference area and was located in the plane of the wing or in a position 18.5 percent of the wing mean geometric chord above the wing plane. In addition, the canard could be located at two longitudinal stations. Two different wing planforms were tested: one with a leading-edge sweep angle of 60 deg and the other with a leading-edge sweep angle of 44 deg. The results indicated that although downwash from the canard reduced the wing lift at angles of attack up to approximately 16 deg, the total lift was substantially greater with the canard on than with the canard off. At angles of attack above 16 deg, the canard delayed the wing stall. Changing canard deflection had essentially no effect on the total lift, since the additional lift generated by the canard deflection was lost on the wing due to an increased downwash at the wing from the canard.

Gloss, B. B.↗

Wind tunnel tests of a full-scale model of a light twin-engine airplane with fixed auxiliary airfoil or leading-edge slot

An investigation has been conducted by means of wind-tunnel tests of a full-scale mockup of a light twin-engine airplane configuration to determine the effects of outboard partial-span slots and of auxiliary airfoils ahead of the leading edge of the wing in improving aerodynamic characteristics at high angles of attack. Both of the stall-control devices gave considerable improvement in high angle-of-attack characteristics with the auxiliary airfoil giving the more favorable results, but neither device performed as well as might have been expected.

Fink, M. P.↗