Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PERMANENT MAGNETS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74

Hurricane Resilient Wind Plant Concept Study Final Report

Hurricanes occur over much of the U.S. Atlantic and Gulf coasts, from Long Island to the U.S.-Mexico border, encompassing much of the nation's primary offshore wind resource. Category 5 hurricanes have made landfall as far north as North Carolina, with Category 3 hurricanes reaching New York with some frequency. Along the US West coast, typhoons strike with similar frequency and severity. At present, offshore wind turbine design practices do not fully consider the severe operating conditions imposed by hurricanes. Although universally applied to most turbine designs, International Electrotechnical Commission (IEC) standards do not sufficiently address the duration, directionality, magnitude, or character of hurricanes. To assess advanced design features that could mitigate hurricane loading in various ways, this Hurricane-Resilient Wind Plant Concept Study considered a concept design study of a 500-megawatt (MW) wind power plant consisting of 10-MW wind turbines deployed in 25-meter (m) water depths in the Western Gulf of Mexico. This location was selected because hurricane frequency and severity provided a unique set of design challenges that would enable assessment of hurricane risk and projection of cost of energy (COE) changes, all in response to specific U.S. Department of Energy (DOE) objectives. Notably, the concept study pursued a holistic approach that incorporated multiple advanced system elements at the wind turbine and wind power plant levels to meet objectives for system performance and reduced COE. Principal turbine system elements included a 10-MW rotor with structurally efficient, low-solidity blades; a lightweight, permanent-magnet, direct-drive generator, and an innovative fixed substructure. At the wind power plant level, turbines were arrayed in a large-scale wind power plant in a manner aimed at balancing energy production against capital, installation, and operation and maintenance (O&M) costs to achieve significant overall reductions in COE.

17 WIND ENERGY↗

A Physicochemical Method for Separating Rare Earths: Addressing an Impending Shortfall

There are currently zero operating suppliers of critical rare earth elements La–Lu, Sc, Y (REs), in the western hemisphere. REs are critical materials due to their importance in clean energy and defense applications, including permanent magnets in wind turbines and phosphors in energy efficient lighting. It is not economically viable to produce pure REs in the U.S. given current separations technology. REs production is dominated by suppliers in the People’s Republic of China (PRC) because of their capacity in liquid­liquid solvent extraction (SX) used to purify mixtures. Weak environmental regulations in the PRC also contribute to a competitive advantage. SX is a cost, time, solvent and waste intensive process but is highly optimized and scalable. The low efficiency of SX derives from the small thermodynamic differences in solvation enthalpy between the RE3+ cations. To foster stable domestic RE production there is a critical need for fundamentally new REs chemistry that contributes to disruptive technologies in RE separations. The overall goal of this project was to develop new thermodynamic bases, and apply them, for the solution separation of rare earth metals. We have developed the chemistry of rare earth metals: La–Lu, Sc and Y, with redox active ligands. Our hypothesis for the project was that electron­hole coupling in complexes of certain lanthanide metals with redox active ligands can be used to manifest chemical distinctiveness and affect separations. We also developed separations based on unique solution equilibria from tailored ligands.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Hydrogen and He Isotope Nanoprobe

Materials that incorporate hydrogen and helium isotopes are of great interest at Sandia and throughout the NNSA and DOE. The Ion Beam Lab at SNL-NM has invented techniques using micron to mm-size MeV ion beams to recoil these light isotopes (Elastic Recoil Detection or ERD) that can very accurately make such measurements. However, there are many measurements that would benefit NW and DOE that require much better resolution, such as the distribution of H isotopes (and 3He) in individual grains of materials relevant to TPBARs, H and He-embrittlement of weapon components important to Tritium Sustainment Programs, issues with GTSs, batteries… Higher resolution would also benefit the field of materials science in general. To address these and many other issues, nm-scale lateral resolution is required. This LDRD demonstrated that neutral H atoms could be recoiled through a thin film by 70 keV electrons and detected with a Channeltron electron multiplier (CEM). The electrons were steered away from the CEM by strong permanent magnets. This proved the feasibility that the high energy electrons from a transmissionelectron- microscope-TEM can potentially be used to recoil and subsequently detect (e-ERD), quantify and map the concentration of H and He isotopes with nm resolution. This discovery could lead to a TEM-based H/He-isotope nanoprobe with 1000x higher resolution than currently available.

36 MATERIALS SCIENCE↗

Beam dynamics validation of the Halbach Technology FFAG Cell for Cornell-BNL Energy Recovery Linac

The Cornell-BNL Electron Test Accelerator (CBETA), a 150 MeV energy recovery linac (ERL) now in construction at Cornell, employs a fixedfield alternating gradient (FFAG) optics return loop: a single beam line comprised of quadrupole doublet cells, which accepts four recirculated energies. CBETA FFAG cell uses Halbach permanent magnet technology, its design studies have covered an extended period of time supported all the way by extensive particle dynamics simulations using computed 3-D field map models. This approach, which supported the choice of Halbach technology for CBETA FFAG ERL in 2016, is discussed and illustrated here based on the final stage in these beam dynamics studies, namely the validation of a ultimate, optimized design of the cell.

43 PARTICLE ACCELERATORS↗

Unique Lanthanide-Free Motor Construction

This project pursued the development of a non-rare-earth permanent magnet motor architecture. It incorporated a novel rotor geometry that allowed the use of lower energy Al-Ni-Co high flux, low coercivity magnet material. This material was not readily adopted at the start of the project, due to demagnetization within existing magnetic circuit designs, a problem that was overcome with the final design produced in the project. The result of the research and testing showed that it is feasible to produce an AlNiCo motor, meeting the DOE performance targets, while exceeding DOE 2015 cost targets and nearly meeting 2020 cost targets.

33 ADVANCED PROPULSION SYSTEMS↗

System Levelized Cost of Energy Analysis for Floating Offshore Vertical-Axis Wind Turbines

The levelized cost of energy for an offshore wind plant consisting of floating vertical-axis wind turbines is studied in this report. A 5 MW Darrieus vertical-axis wind turbine rotor is used as the study turbine as this architecture was determined to have the greatest ability to reduce the system cost. The rotor structural design was used with blade manufacturing cost model studies to estimate its cost. A two-bladed, carbon fiber rotor was selected in this analysis since the lower topside mass resulted in a reduction of the platform costs which exceeded the increased rotor cost. A direct-drive, medium efficiency drivetrain was designed which represents 25% of the costs and 45% of the mass of the combined rotor/drivetrain system. A direct-drive, permanent magnet generator drivetrain was selected due to the improved reliability of this type of system, while the cost was not significantly higher than for geared drivetrains. A platform was designed by first identifying the optimal architecture for the vertical-axis wind turbine at a water depth of 150 m. A survey was performed of floating platform types, and six characteristic designs were analyzed which span the range of stability mechanisms available to floating systems. A multi-cellular tension-leg platform was identified as the lowest cost platform which additionally provided some interesting performance benefits. The small motions of the tension-leg platform benefit the system energy capture while limiting inertial loads placed on the rotor’s tower and blades. A final design was produced for the multi-cellular tension-leg platform considering operational fatigue, storm wind and wave conditions, and tow-out design cases. The driving design load was stability during tow-out while ballasting the platform. System levelized cost of energy was calculated, including operational expenses and balance of system costs estimated for the wind plant. Opportunities for reduction in the component costs are predicted and used to make projections of the system levelized cost of energy for future developments. The opportunities and challenges for floating vertical-axis wind turbines are identified by the system design and levelized cost of energy analysis.

17 WIND ENERGY↗

TM 6: Fractional Arc Test - beam through MLC & girder

On April 18 2018, the CBETA project achieved technical milestone 6, “Fractional Arc Test: beam through the Main Linac Cryomodule and prototype girder ”, which is also a major funding milestone. For this test the electron beam was accelerated to a final energy of 42 MeV in the Main Linac Cryomodule (MLC), before being passed through the first splitter beam line S-1 and through the first permanent magnet arc girder (PMA). The MLC contains six superconducting accelerating cavities; for this test only five of the six were powered due to a temporary fault in cavity number 5.

43 PARTICLE ACCELERATORS↗

North Slope of Alaska ARM Facilities Monthly Status Report- January 2019

During the month of January 2019, the TBS crew made progress revamping the equipment to prepare for upcoming 2019 flights. Both winches were upgraded using a SE encore E43 59.3:1 gearbox coupled with a Leeson Permanent magnet motor. This increased the torque capability by approximately 3x and the rotational speed by ~30%. The existing electronics system on one winch was repurposed to power four 3,500 lb ATV winches. These winches will automate the retrieval of the balloons allowing for retrieval during faster winds, and thus increasing potential operating conditions, while also improving crew safety. The ATV winches are expected to be added to the second winch in February. Finally, a new electronics box was designed which will be used to power the new winch motor. The new winch motors are variable speed, meaning they accept 0-180V and the speed correlates to the input voltage. The new electronics boxes will be mounted directly to the winches to allow the winches to be removed from the trailers in case of size/weight operating limitations. The winches will instead be powered directly by 220V generators vs the lead acid battery banks used by the previous systems.

42 ENGINEERING↗

HTurbine Generator, 1.5-6 MW, Manufacturing

This unit process tracks materials and energy needed to manufacture high-speed and medium-speed permanent-magnet generators for horizontal 1.5 to 6 MW wind turbines, and manufacturing of direct drive with negligible amounts of other materials. To access the model referenced in the report, please visit https://www.netl.doe.gov/energy-analysis/details?id=BA87A065-6A2E-40C0-AFB5-A9CED16ED1D6

17 WIND ENERGY↗

The CBETA Fractional Arc Test

As part of this development effort, the Cornell-BNL Energy recovery linac Test Accelerator (CBETA) [3], a 4-pass, 150 MeV energy recovery linac (ERL), utilizing a Non-scaling Fixed Field Alternating-gradient (NS-FFA) permanent magnet return loop, is currently under design and construction at Cornell University through the joint collaboration of Brookhaven National Lab (BNL) and the Cornell Laboratory for Accelerator based Sciences and Education (CLASSE). Building on the significant advancements in high-brightness photoelectron sources and SRF technology at Cornell, as well as the FFA magnet and lattice design expertise from BNL, CBETA will establish the operation of a multi-turn SRF based ERL utilizing a compact FFA return loop with large energy acceptance (a factor of roughly 3.6 in energy), and thus demonstrate one possible cost-reduction technology under consideration for the eRHIC design. Moreover, successful completion of the CBETA project requires the study and measurement of many critical phenomena relevant to designing the EIC: the Beam-Breakup (BBU) instability, halo-development and collimation, growth in energy spread from Coherent Synchrotron Radiation (CSR), and CSR micro bunching, and thus should provide valuable insight to the EIC and ERL communities. In order to demonstrate the viability of the CBETA design, the Fractional Arc Test (FAT) was added to the CBETA commissioning sequence.

43 PARTICLE ACCELERATORS↗

Beam Commissioning Results from the CBETA Fractional Arc Test (CBETA Note 030)

This work describes first commissioning results from the Cornell Brookhaven ERL Test Accelerator fractional arc test. These include the recommissioning of the Cornell photoinjector, the first full energy operation of the main linac with beam, as well as commissioning of the lowest energy matching beamline (splitter) and a partial section of the Fixed Field Alternating gradient (FFA) return loop featuring first production Halbach style permanent magnets. Achieving these tasks required characterization of the injection beam, calibration and phasing of the main linac cavities, demonstration of the required 36 MeV energy gain, and measurement of the splitter line horizontal dispersion and R 56 at the nominal 42 MeV. In addition, a procedure for determining the BPM offsets, as well as the tune per cell in the FFA section via scanning the linac energy and inducing betatron oscillations around the periodic orbit in the fractional arc was developed and tested. A detailed comparison of these measurements to simulation is discussed.

43 PARTICLE ACCELERATORS↗

Ultra High Temperature Anode Recycle Blower for Solid Oxide Fuel Cell (Phase I Final Report)

Under funding from DOE Award DE-FE0031148, Mohawk Innovative Technology, Inc. (MITI) has successfully developed, integrated and tested a prototype ultrahigh speed oil-free blower for use as an Ultra High Temperature Anode Recycle Blower (UHT-ARCB) in a 100 kWe Solid Oxide Fuel Cell (SOFC). MITI’s recycle blower design is hermetically sealed, and features a completely encapsulated permanent magnet motor, which allows it to handle the steam-rich anode recycle gas mixture. At the SOFC’s nominal operating condition, the MITI ARCB rotates at approximately 55000 rpm, raises the pressure of the incoming 621 °C gas from 104 to 112 kPa, and uses less than 1.2 kWe at a rate of approximately 30 g/s. The UHT-ARCB’s thermal management uses the incoming natural gas supply for the SOFC as cooling medium for bearings, seals and motor magnet, along with a water jacket for motor housing cooling to prevent the high temperature gas from affecting the bearing/motor assembly. MITI’s development of this UHT-ARCB will contribute to a reduction of cost and overall balance of plant (BOP) of SOFC systems. The UHT-ARCB recirculates a fraction of the depleted anode exhaust to the fuel-cell inlet. Direct recycling of anode off-gas takes advantage of the water already present in the stream to assist the methane reforming process and inhibit carbon deposition, without the need for an external water supply.

30 DIRECT ENERGY CONVERSION↗

Application of the Kramers-Kronig Relations in the Field Integral Measurements

This technical note describes the interdependence between the vertical (Iy) and horizontal (Ix) component of the first field integral generated by permanent magnets (or magnetic module). The analytical expression is derived making use of the Kramers-Krönig relations [1]. It is only valid when all magnetic sources are in the same side of the line of measure. A detail explanation of these equations is presented.

36 MATERIALS SCIENCE↗

Development and Operation of a High Throughput Computer Hard Disk Drive Recycling Enterprise (CRADA NFE-16-05989)

The aim of this collaborative effort is to develop, construct and operate a high throughput computer hard disc drive (HDD) recycling system. Research conducted as part of the Critical Materials Institute (CMI), a Department of Energy (DOE) Energy Innovation Hub, has revealed the economic rationale and the necessary technology for a potentially viable HDD recycling enterprise. Moreover, the very notion of CMI is the development of replacement sources of rare earth critical materials that enable the U.S. to become less dependent on single source supplies. Focused on end-of-life (EOL) consumer products containing rare earth permanent magnets, this cooperative endeavor will develop, construct and operate a highly automated recycling process. Demonstrating economically viable recycling of high value products is largely an untapped resource in the U.S. Recycling HDDs to recover rare earth magnets and other valuable materials (e.g. aluminum, steel, printed circuit boards, copper, etc.) presents a new opportunity to satisfy U.S. demand for highly desirable commodities. The goal of this cooperative research and development agreement (CRADA) project is to create a commercial HDD recycling enterprise that changes the landscape of rare earth magnet material and magnet availability for U.S. manufacturers. Underpinning this primary goal is the development and demonstration of an economic HDD recycling process that provides a significant and alternative supply of rare earth magnets that is not dependent upon foreign sourcing. Oak Ridge National Laboratory (ORNL) has researched the technology options and down selected specific sub-process technologies based upon throughput and economic potential. The participant, however, brings significant process design, development and operational experience that may result in process improvement or optimization strategies that will be explored in collaboration with the contractor. The final outcome of this CRADA is a system/process for recycling large quantities of HDDs. The technology is available for commercial scale-up.

42 ENGINEERING↗

Optimization of DARHT Axis 1 Injector Voltage

The Dual-Axis Radiographic Hydrodynamic Test (DARHT) facility provides flash radiography capabilities using two electron Linear Induction Accelerators (LIA’s). Axis-1 of DARHT produces a 20- MeV, 2-kA, 80-ns-FWHM electron beam. The strict requirements for flash radiography require a detailed understanding of the LIA’s performance, including precision measurements of the injector electron beam energy. The technique for time resolved measurement of the electron beam energy using electron Permanent Magnet Spectrometer (ePMSpec) has been developed. The electron energy then is used to infer the voltage produced by the injector pulsed power. The injector pulsed power of DARHT I consists of a 1.5-MV, glycol-insulated Blumlein that is pulsecharged by a step-up transformer and switched by four, laser-triggered spark gaps. A series of increasing impedance transmission lines are used to transform the output voltage of the Blumlein to a maximum of 3.8MV at the diode. Figure 1a shows a graphic of the Axis-1 prime power tank, Blumlein and downstream transmission lines. The injector pulse power is designed to produce voltage on a velvet cathode located in the vacuum vessel. The specifications of the voltage-pulse flat-top over 60ns is +/-1%. A key element in the high-voltage circuit is the ethylene glycol Blumlein. The outer volume, adjacent to the laser triggered switches of the Blumlein, is a peaking capacitor. This is an independent volume that contains a mixture of ethylene glycol and water to make it an adjustable capacitor of 380 to 750 pF.

43 PARTICLE ACCELERATORS↗

A Hydrogen and Helium Isotope Nanoprobe

Materials that incorporate hydrogen and helium isotopes are of great interest at Sandia. The Ion Beam Lab at SNL-NM has invented techniques using micron to mm-size MeV ion beams to recoil these light isotopes (Elastic Recoil Detection or ERD) that can very accurately make such measurements. However, there are many measurements that would benefit NW and DOE that require much better resolution. To address these and many other issues, this LDRD demonstrated that neutral H atoms could be recoiled through a thin film by 70 keV electrons and detected with a Channeltron electron multiplier (CEM). The electrons were steered away from the CEM by strong permanent magnets. This proved the feasibility that the high energy electrons from a transmission-electron-microscope-TEM can potentially be used to recoil and subsequently detect (e-ERD), quantify and map the concentration of H and He isotopes with nm resolution.

36 MATERIALS SCIENCE↗

Thermal Hydraulic Experimental Test Article (FY21 Final Report)

The Thermal Hydraulic Experimental Test Article (THETA) is a facility that will be used to develop sodium components and instrumentation as well as acquire experimental data for validation of reactor thermal hydraulic and safety analysis codes. The facility will simulate nominal conditions as well as protected/unprotected loss of flow accidents in a sodium-cooled fast reactor (SFR). High fidelity distributed temperature profiles of the developed flow field will be acquired with Rayleigh backscatter based optical fiber temperature sensors. The facility is being designed in partnership with systems code experts to tailor the experiment to ensure the most relevant and highest quality data for code validation. THETA is comprised of a traditional primary and secondary system. The primary system is submerged in the pool of sodium and consists of a pump, electrically heated core, intermediate heat exchanger, and connected piping and thermal barriers (redan). The secondary system, located outside of the sodium pool, consists of a pump, sodium to air heat exchanger, and connected piping and valves. Figure 1 illustrates the main components of the primary system. THETA has been installed in the Mechanisms Engineering Test Loop (METL) with the primary system in the 28 inch Test Vessel #4, Figure 2 and Figure 3. Since the FY20 THETA status report, further water shakedown testing was performed, some final welding modifications were performed, all system components were sanitized, dry assembled, and commissioned. The THETA submersible electromagnetic flowmeter was welded closed to hermetically seal internal components from sodium followed by a helium leak check for the final time. Following installation of THETA into vessel #4, all data acquisition and control systems were brought online and commissioned at room temperature in the argon gas space of the empty vessel. The vessel zone 1 heaters were reinstalled and the flange was then insulated. The vessel 4 heaters were brought to a temperature of 100 °C and the THETA pump was jogged at 600 RPM to ensure it was functioning correctly. The secondary, AC Conduction based electromagnetic pump from CMI Novacast (product number CA-15) was ordered and will be delivered in late calendar year 2021. The custom designed permanent magnet based secondary flowmeter was designed, a drawing package and manufacturing specification created and quote requested from a machine shop. The intermediate heat exchanger design was completed and a drawing package is currently in progress. During the middle of calendar year 2021 the Building 308 sodium scrubber system was shut down in order to replaced some corroded piping and facilitate improvements on the system, thus requiring the sodium in METL to remain frozen. This has imposed a delay in filling vessel 4 with sodium to begin THETA testing. Sodium testing is expected to begin in early fiscal year 2022 as all THETA primary systems are operational.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Sodium Hydrogen Sensor and Acoustic Flow Sensor Development

This report documents the development of diffusion-type hydrogen meters (DTHMs) as part of a steam generator leak detection system (SGLDS) of sodium-cooled fast reactors (SFR) and the demonstration of the capabilities of acoustic flowmeters, including a commercial UTFM (Flexim FLUXUS F721) and an Argonne HT acoustic flowmeter running on shear-to-longitudinal mode. It also evaluates two Argonne permanent magnet flowmeters (PMFMs).

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗