Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Materials Compatibility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74

Bench-Scale Dense Phase Biomass Feed Insertion Tests

The objective of this work is to provide the technical data needed to understand whether representative agriculture, woody, and energy crops could be inserted with the established conveyance, grinding, and transport lines in an existing power plant. This report considers the material properties and processing steps necessary to render biomass compatible with conventional coal fired boilers in a cofiring scenario.

09 BIOMASS FUELS↗

High pressure oxygen utilization by NASA

Although NASA is not one of the country's major oxygen consumers, it uses oxygen under severe conditions including very high flow rates and pressure. Materials for such applications must be carefully selected for compatibility, because susceptibility to ignition increases as operating pressure is raised. Much work is needed, however to define the selection criteria. Some of the work in this area that is being performed under sponsorship of NASA's Aerospace Safety Research and Data Institute (ASRDI) is described.

Belles, F. E.↗

FSA field test report, 1980 - 1982

Photovoltaic modules made of new and developing materials were tested in a continuing study of weatherability, compatibility, and corrosion protection. Over a two-year period, 365 two-cell submodules have been exposed for various intervals at three outdoor sites in Southern California or subjected to laboratory acceptance tests. Results to date show little loss of maximum power output, except in two types of modules. In the first of these, failure is due to cell fracture from the stresses that arise as water is regained from the surrounding air by a hardboard substrate, which shrank as it dried during its encapsulation in plastic film at 150 C in vacuo. In the second, the glass superstrate is sensitive to cracking, which also damages the cells electrostatically bonded to it; inadequate bonding of interconnects to the cells is also a problem in these modules. In a third type of module, a polyurethane pottant has begun to yellow, though as yet without significant effect on maximum power output.

Maxwell, H. G.↗

Channel electron multiplier compatibility with Viton and Apiezon-L vacuum grease

Clean Viton and Viton coated with Apiezon-L vacuum grease were tested for their noncontaminating compatibility with channel electron multipliers (CEMs). The test setup and procedure were the same as those used previously in conjunction with CEM compatibility tests of certain epoxies, solder, and fluorocarbon polymer materials useful for construction of spaceflight sensors. While some CEM gain degradation was noted during exposure to Viton and Apiezon-L, the present tests indicate that, at least over instrument lifetimes of about 2 x 10 to the 12th counts, these materials should be suitable for (1) preflight space sensor testing systems, (2) hermetic seals for CEM-based space sensors, and (3) terrestrial CEM-based instrumentation.

Mccomas, D. J.↗

Manufacturing development of pultruded composite panels

The weight savings potential, of graphite-epoxy composites for secondary and medium primary aircraft structures, was demonstrated. One of the greatest challenges facing the aircraft industry is to reduce the acquisition costs for composite structures to a level below that of metal structures. The pultrusion process, wherein reinforcing fibers, after being passed through a resin bath are drawn through a die to form and cure the desired cross-section, is an automated low cost manufacturing process for composite structures. The Lockheed Aeronautical Systems Company (LASC) Composites Development Center designed, characterizated materials for, fabricated and tested a stiffened cover concept compatible with the continuous pultrusion process. The procedures used and the results obtained are presented.

Meade, L. E.↗

Precision aqueous cleaner for RSRM

Chlorinated solvents such as freon and 1,1,1 trichloroethane (TCA) are both environmental and physiological hazards which deplete stratospheric ozone. These chemicals are the primary degreasing solvents (vapor, vat, and hand operations) in redesigned solid rocket motor (RSRM) manufacturing. Due to the mandates of the Clean Air Act, substitutes must be identified for RSRM cleaning processes. The initial phase of laboratory testing identified candidate cleaners to replace 1,1,1 trichloroethane for cleaning, potentially reducing annual TCA consumption by 800,000 lbs. This paper describes RSRM testing which elucidated the effects of several interdependent variable including: definition of surface cleanliness criteria, validation of cleaning power of new candidates, the effect of immersion cleaning versus spray cleaning on cleaning, any effect of the cleaner and/or inhibitor upon bondline aging, and compatibility of the cleaners with nonmetallic tooling and processing materials.

Hutchens, D. E.↗

Microelectromechanical Systems for Aerodynamics Applications

Microelectromechanical systems (MEMS) embody the integration of sensors, actuators, and electronics on a single substrate using integrated circuit fabrication techniques and compatible micromachining processes. Silicon and its derivatives form the material base for the MEMS technology. MEMS devices, including micro-sensors and micro-actuators, are attractive because they can be made small (characteristic dimension about microns), be produced in large numbers with uniform performance, include electronics for high performance and sophisticated functionality, and be inexpensive. MEMS pressure sensors, wall-shear-stress sensors, and micromachined hot-wires are nearing application in aeronautics. MEMS actuators face a tougher challenge since they have to be scaled (up) to the physical phenomena that are being controlled. MEMS actuators are proposed, for example, for controlling the small structures in a turbulent boundary layer, for aircraft control, for cooling, and for mixing enhancement. Data acquisition or control logistics require integration of electronics along with the transducer elements with appropriate consideration of analog-to-digital conversion, multiplexing, and telemetry. Altogether, MEMS technology offers exciting opportunities for aerodynamics applications both in wind tunnels and in flight

Mehregany, Mehran↗

Characteristics of Elastomer Seals Exposed to Space Environments

A universal docking and berthing system is being developed by the National Aeronautics and Space Administration (NASA) to support all future space exploration missions to low-Earth orbit (LEO), to the Moon, and to Mars. The Low Impact Docking System (LIDS) is being designed to operate using a seal-on-seal configuration in numerous space environments, each having unique exposures to temperature, solar radiation, reactive elements, debris, and mission duration. As the LIDS seal is likely to be manufactured from an elastomeric material, performance evaluation of elastomers after exposure to atomic oxygen (AO) and ultraviolet radiation (UV) was conducted, of which the work presented herein was a part. Each of the three candidate silicone elastomer compounds investigated, including Esterline ELA-SA-401, and Parker Hannifin S0383-70 and S0899-50, was characterized as a low outgassing compound, per ASTM E595, having percent total mass loss (TML) less than 1.0 percent and collected volatile condensable materials (CVCM) less than 0.1 percent. Each compound was compatible with the LIDS operating environment of -50 to 50 C. The seal characteristics presented include compression set, elastomer-to-elastomer adhesion, and o-ring leakage rate. The ELA-SA-401 compound had the lowest variation in compression set with temperature. The S0383-70 compound exhibited the lowest compression set after exposure to AO and UV. The adhesion for all of the compounds was significantly reduced after exposure to AO and was further decreased after exposure to AO and UV. The leakage rates of o-ring specimens showed modest increases after exposure to AO. The leakage rates after exposure to AO and UV were increased by factors of up to 600 when compared to specimens in the as-received condition.

Daniels, Christopher C.↗

Frontiers of Life Sciences: The Human Exploration of the Moon and Mars

The rapid development of the productive processes after World War II extended human settlements into new ecological niches. Advances in Life Sciences played a decisive role supporting the establishment of human presence in areas of the planet where human life could have not existed otherwise. The evolution of life support systems, and the fabrication of new materials and technologies has enabled humans to inhabit Polar Regions, ocean surfaces and depths; and to leave Earth and occupy Low Earth Orbit. By the end of the 20 th Century, stations in the Antarctic and Arctic, off shore oil platforms, submarines, and space stations had become the ultimate demonstration of human ability to engineer habitats at Earth extreme environments and outer space. As we enter the 21st Century, the next development of human settlements will occur through the exploration of the Moon, Mars, and beyond. The major risks of space exploration derive from long exposure of humans and other life systems to radiation, microgravity, isolation and confinement, dependence on artificial life support systems, and unknown effects (e.g., altered magnetic fields, ultrahigh vacuum on bacteria, fungi, etc.). Countermeasures will require a complete characterization of human and other biological systems adaptation processes. To sustain life in transit and on the surface of the Moon and Mars will require a balance of spacecraft, cargo, astronaut crews, and the use of in situ resources. Limitations on the number of crewmembers, payloads, and the barrenness of the terrain require a novel design for the capabilities needed in transit and at exploration outpost sites. The planned destinations have resources that may be accessed to produce materials, food, shelter, power, and to provide an environment compatible with successful occupation of longterm exploration sites. Once more, the advancements of Life Sciences will be essential for the design of interplanetary voyages and planetary surface operations. This presentation delineates the role of Life Sciences and its frontiers, especially Cell Science, in the context of human exploration. Life support systems, food production, and medical equipment encompass many of vital aspects related to the new vision for NASA.

North, Regina M.↗

Design and Specifications for the Highland Regolith Prototype Simulants NU-LHT-1M and -2M

The first two prototype lunar regolith simulants were to replicate characteristics of the lunar highlands. A major change from initial plans was to use an estimate of typical Apollo 16 highland material rather than a specific core. This change was compatible with project objectives and necessitated by the lack of adequate data from a single core. To make the initial simulant, a crystalline component and a glass component were deemed necessary. Lithic feedstocks were obtained with the assistance of the Stillwater Mining Company. The mixing of the rock constituents was done based on normative mineralogy rather than modal mineralogy. This was done to simplify development. A major design decision was not to attempt simulation of the range of glass chemistries observed in Apollo samples. A single glass was assumed to be adequate for engineering purposes for which the simulant would be used. Glass was made in a process developed at Zybek Advanced Products of Boulder, Colorado. Mill sand was used as the feedstock for this process. A second generation of the simulant was made that incorporated the additional minerals apatite, synthetic whitlockite, and pyrite. The olivine source was changed to the commercially produced Twin Sisters Dunite, and a pseudo-agglutinate product was invented and added to the -2M product. The pseudo-agglutinate captures all of the lunar agglutinate features but does not attempt to incorporate nanophase Fe.

Stoeser, D.↗

Li-Ion Electrolytes with Improved Safety and Tolerance to High-Voltage Systems

Given that lithium-ion (Li-ion) technology is the most viable rechargeable energy storage device for near-term applications, effort has been devoted to improving the safety characteristics of this system. Therefore, extensive effort has been devoted to developing nonflammable electrolytes to reduce the flammability of the cells/battery. A number of promising electrolytes have been developed incorporating flame-retardant additives, and have been shown to have good performance in a number of systems. However, these electrolyte formulations did not perform well when utilizing carbonaceous anodes with the high-voltage materials. Thus, further development was required to improve the compatibility. A number of Li-ion battery electrolyte formulations containing a flame-retardant additive [i.e., triphenyl phosphate (TPP)] were developed and demonstrated in high-voltage systems. These electrolytes include: (1) formulations that incorporate varying concentrations of the flame-retardant additive (from 5 to 15%), (2) the use of mono-fluoroethylene carbonate (FEC) as a co-solvent, and (3) the use of LiBOB as an electrolyte additive intended to improve the compatibility with high-voltage systems. Thus, improved safety has been provided without loss of performance in the high-voltage, high-energy system.

Smart, Marshall C.↗

Material Usage in High Pressure Oxygen Systems for the International Space Station

The Nitrogen/Oxygen Recharge System (NORS) for the International Space Station (ISS) Program was required as part of the Space Shuttle retirement efforts to sustain the ISS life support systems. The system is designed around a 7000 psia Oxygen or Nitrogen Recharge Tank Assembly which is able to be utilized both internally and externally to the ISS. Material selection and usage were critical to ensure oxygen compatibility for the design, while taking into consideration toxicity, weldability, brazability and general fabrication and assembly techniques. The system uses unique hardware items such a composite overwrap pressure vessel (COPV), high pressure mechanical gauges, compact regulators and valves, quick disconnects, metal tubing and flexhoses. Numerous challenges and anomalies were encountered due to the exotic nature of this project which will be discussed in detail. The knowledge gained from these anomalies and failure resolutions can be applied to more than space applications, but can also be applicable to industry pressurized systems.

Kravchenko, Michael↗

Creating a Universal PV Plug and Socket Standard

Photovoltaic connectors are designed to be quick and easy to install. Current connector qualification standards, such as UL 6703 and IEC 62852, are only intended to evaluate connectors from the same manufacturer and were recently changed to explicitly proscribe the mating of connectors from different manufacturers. Unfortunately, the industry has chosen to design connectors that will commonly connect together with those from other manufacturers. This is done to simplify installation avoiding the situations such as when the connectors on a microinverter, or other module level power electronics, do not match the connectors on the modules in the system. This rampant violation of electrical codes worldwide indicates that there is a strong desire and need to develop a universal connector standard. Here we present the initial approach and philosophy behind the formation of an IEC subgroup under TC82 WG2 looking at this problem. We intend to develop a standard where the materials and geometry of construction are specified to ensure compatibility and the design is intended to be of the highest quality. We expect that this connector will be more costly but especially in rooftop installations where power electronics requires matching components from several manufacturers, that this may still result in a net cost savings. These connectors must be of the highest quality because we wouldn’t want to develop a connector that precluded the manufacturing of a higher quality product, and because these will most commonly be used on rooftop installations where safety is more of a concern. Additionally, because we do not know which brands of connectors will be used together, we cannot simply rely on test results to ensure safety but must create a design that is as inherently safe as possible.

connectors↗

Morphology and properties of recycled polypropylene/bamboo fibers composites

Polypropylene (PP) is among the most widely used thermoplastics in many industrial fields. However, like other recycled polymers, its properties usually decrease after recycling process and sometimes are degraded to poor properties level for direct re-employment. The recycled products, in general, need to be reinforced to have competitive properties. Short bamboo fibers (BF) have been added in a recycled PP (RPP) with and without compatibilizer type maleic anhydride polypropylene (MAPP). Several properties of composite materials, such as helium gas permeability and mechanical properties before and after ageing in water, were examined. The effects of bamboo fiber content and fiber chemical treatment have been also investigated. We showed that the helium permeability increases if fiber content is higher than 30% because of a poor adhesion between untreated bamboo fiber and polymer matrix. The composites reinforced by acetylated bamboo fibers show better helium permeability due to grafting of acetyl groups onto cellulose fibers surface and thus improves compatibility between bamboo fibers and matrix, which has been shown by microscopic observations. Besides, mechanical properties of composite decrease with ageing in water but the effect is less pronounced with low bamboo fiber content.

36 MATERIALS SCIENCE↗

Recent Progress in Solid‐State Lithium Batteries through Cathode Microstructure Engineering

A high‐performance cathode is necessary to realize the great potentials of solid‐state batteries such as high energy density and long cycle life. It is also needed to validate electrolyte performance, which is lacking. Currently, cathodes for solid‐state batteries are thinner and have lower cathode active material content than their lithium‐ion battery counterpart, resulting from insufficient conductivity and limiting the battery energy density. This review article provides an overview of recent development in cathode microstructures and their impact on battery properties, including compatibility between cathode and electrolyte, cathode architecture design, interface engineering, correlation between material properties, cathode processing approaches, and performance, as well as the advanced characterization methods used to understand the above correlations . Some perspectives on future development are shared including utilizing in situ and operando characterization tools to better understand dynamic evolution of the cathode/electrolyte interface, adapting artificial intelligence and machine learning to design and optimize cathode structures. The article is aimed to promote research interest on cathode development and advance solid‐state battery technologies.

cathode engineering↗

Alternative Crucibles for U-Mo Microwave Melting

The crucibles used currently for microwave melting of U-Mo alloy at the Y-12 Complex contain silicon carbide (SiC) in a mullite (3Al 2 O 3 -2SiO 2 ) matrix with an erbia coating in contact with the melt. Due to observed silicon contamination, Pacific Northwest National Laboratory has investigated alternative crucible materials that are susceptible to microwave radiation and are chemically compatible with molten U-Mo at 1400 1500C. Recommended crucibles for further testing are: 1) high-purity alumina (Al 2 O 3 ); 2) yttria-stabilized zirconia (ZrO 2 ); 3) a composite of alumina and yttria-stabilized zirconia; 4) aluminum nitride (AlN). Only AlN does not require an erbia coating. The recommended secondary susceptor, for heating at low temperature, is SiC in a “picket fence” arrangement.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of sputtered techniques for thrust chambers, task 1

Filler materials proposed for use in the sputter fabrication regeneratively cooled thrust chambers were evaluated. Low melting castable alloys, CERROBEND. CERROCAST, and CERROTRU, slurry applied SERMETEL 481 and flame-sprayed aluminum were investigated as filler materials. Sputter deposition from a cylindrical cathode inverted magnestron was used to apply an OFHC copper closeout layer to filled OFHC copper ribbed-wall cylindrical substrates. The sputtered closeout layer structure was evaluated with respect to filler material contamination, predeposition machining and finishing operations, and deposition parameters. The application of aluminum by flame-spraying resulted in excessiver filler porosity. Though the outgassing from this porosity was found to be detrimental to the closeout layer structure, bond strengths in excess of 10,500 psi were achieved. Removal of the aluminum from the grooves was readily accomplished by leaching in a 7.0 molar solution of sodium hydroxide at 353 K. Of the other filler materials evaluated, CERROTRU was found to be the most suitable material with respect to completely filling the ribbed-wall cylinders and vacuum system compatibility. However, bond contamination resulted in low closeout layer bond strength with the CERROTRU filler. CERROBEND, CERROCAST, and SERMETEL 481 were found to be unacceptable as filler materials.

Mullaly, J. R.↗