SEARCH · Engineering Papers

Results for “Manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74

All sources NASA NTRS DOE OSTI

DOE OSTI2026

An Overview of Manufacturing Controls for Production of High-Consequence, Single-Use Systems

Extended Testing (Crowder, et al. (2025) ) is a reliability demonstration technique that can be used to dramatically reduce sample size requirements. Manufacturing controls are needed to supplement extended testing by identifying production issues that a reduced sample sizes might overlook, especially built-in, or latent, manufacturing defects. This report focuses on some of the most commonly used, yet most impactful, manufacturing control tools that are used to limit production-related defects and efficiently screen any remaining defects at final inspection. These tools include statistical process control (SPC), acceptance sampling, environmental stress screening (HASS and ESS), and mistake proofing. The goal is to minimize the probability that built-in defects ever reach the customer. In terms of nuclear weapons (NW), the goal is to prevent defective units from ever entering the nation’s NW stockpile. Examples of each of the techniques are illustrated with case studies.

42 ENGINEERING↗

DOE OSTI2025

High Throughput Solvent-free Manufacturing of Battery Electrodes

The project goal is to develop and demonstrate an advanced solvent-free lithium-ion battery electrode process through proposed Advanced Dry Electrode Process (ADEP) equipment, which is expected to exhibit a better binder fibrillization and high throughput and suitable for high performance electrode manufacturing, and commonize the anode and cathode dry processing equipment, supply chain and operation for lithium-ion battery OEMs for replacing the solvent-based slurry casting. Our proposed approach will facilitate low-cost battery production by addressing the following gaps in present dry electrode processing: • Extend the dry electrode fabrication process to lithium-ion battery anode manufacturing • Increase the active material content for anodes and cathodes • Intensify the process through improved mixing, powder rheology and surface modifications • Enable processing of next-generation electrode materials that are not stable to solvent or ambient air exposure. The project objectives include the development of anode-compatible binder and binder fibrillization promoter for low irreversible capacity loss, low electrode binder content yet higher film mechanical strength, and the optimization of solvent-free anode and cathode process for low cost (>60% electrode cost reduction), high performance (10% increase in energy density without sacrificing cycle life) and high throughput to enable next generation lithium-ion battery electrode production. Solvent-free electrode manufacturing will also enable next-generation cell designs based on prelithiated anodes or solid-state electrolytes.

25 ENERGY STORAGE↗

DOE OSTI2025

The Effects of Manufacturing Techniques on Neutron-Irradiated C26M Mechanical Properties

Nuclear energy provides 13% of the total energy produced globally. To further improve the safety and reliability of nuclear reactors material challenges need to be successfully resolved. C26M/FeCrAl alloy systems can improve the safety and reliability of current Generation III reactors due to the potential benefits of a stable passivation layer from the Al, which can protect against corrosion, and promising mechanical performance at boiling- and light-water reactor temperatures. However, information is limited on how manufacturing techniques affect the mechanical performance of C26M in neutron-irradiated environments. In this research, C26M specimens were manufactured using three techniques and then irradiated at the Advanced Test Reactor at Idaho National Laboratory. This research aims to bridge this gap by investigating how the manufacturing techniques affects the mechanical performance of irradiated C26M at Generation III reactor relevant temperatures.

36 - MATERIALS SCIENCE↗

DOE OSTI2026

Novel additive manufacturing for plasma facing materials ‐ creating a research pathway for minority students

This project addresses two critical and intertwined challenges in fusion energy, namely the shortage of a broadly trained scientific workforce and the lack of scalable manufacturing solutions for plasma-facing components (PFCs). Through a collaboration among Florida International University (FIU), Miami Dade College (MDC), and Purdue University, the project established structured, reproducible educational and research pathways that recruit and advance students from institutions historically outside the fusion energy enterprise, building the human capital that this field urgently needs. The project integrates the complementary research strengths of FIU and Purdue to investigate flash sintering as a transformative processing route for tungsten-based PFCs. Unlike conventional sintering approaches, flash sintering offers rapid densification at significantly reduced thermal budgets, making it a compelling candidate for fabricating complex tungsten geometries that must withstand extreme plasma-facing environments. Systematic experimental and modeling efforts will elucidate the fundamental mechanisms governing microstructure evolution, grain boundary chemistry, and thermomechanical response during flash sintering — knowledge that is presently lacking but essential for translating this technology into reliable manufacturing practice. The convergence of workforce development and cutting-edge manufacturing research positions this project to deliver measurable, durable impact: a pipeline of fusion-ready researchers cultivated through expanded institutional partnerships, and a validated materials processing framework that accelerates domestic readiness for next-generation fusion reactor construction.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2026

Low-Cost Highly Recyclable Structural Composites Utilizing Vitrimers and Natural Fibers (Basalt) Manufactured via a Novel Pultrusion Method for High-Volume Applications

The project’s overall goal is to explore and demonstrate as proof-of-concept that a highly recyclable and repairable composite material system, that is reinforced with natural fibers, can be used to produce lightweight structural components using a low-cost manufacturing process for high-volume automotive applications. More specifically, the project’s objectives will focus on vitrimer resins (which are a hybrid polymeric system of thermoplastics and thermosets) reinforced with basalt fibers and manufactured using pultrusion technologies. Pultrusion, as a method, is well-known to be one of the lowest-cost manufacturing processes for high-volume applications. However, to date, the validity and viability of such attractive objectives have not been demonstrated in support of the automotive industry.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Advanced Manufacturing of Cathode Materials for Lithium-ion Batteries

Original objectives (per the Statement of Project Objectives) centered on developing and translating a continuous pilot process for cathode materials production while targeting (i) a 29% manufacturing cost reduction, (ii) an 82% energy consumption reduction for cathode production, and (iii) a doubling of manufacturing productivity. Planned validation included characterization at appropriate analytical facilities and electrochemical performance evaluation progressing from half-cells to pouch-cell formats, with a pathway to kilogram-scale production of finished cathode materials for representative testing. Scope evolution: During execution, the project team identified that the surfactant-enabled chemistry offered high selectivity for lithium precipitation from brine sources. A formal scope revision shifted the final project year from cathode manufacturing development to direct lithium extraction/lithium recovery, while maintaining the overarching intent of cost reduction and process simplification relevant to the battery supply chain.

25 ENERGY STORAGE↗

DOE OSTI2019

Effect of surface treatment of microfiberlated cellulose fibers on biocomposite properties and additive manufacturing process

Polymer additive manufacturing (AM) is a rapidly growing technology and it is transitioning to become an advanced manufacturing technique with the introduction of fiberlar reinforcing materials such as carbon and glass fibers into polymer feedstock. As a result of increasing environmental and long-term sustainability concerns, there is an increasing interest in using bio-derived cellulose fibers to reinforce composites instead of carbon and glass fibers. Melt extrusion/fused filament fabrication method is the most commonly used polymer AM technique which enables direct digital manufacturing of parts with complex geometry with a controlled anisotropic distribution of reinforcing phase. However, there are multiple factors that affect the mechanical performance of the final part such as the dispersion and orientation of the reinforcing fibers, the adhesion between the fibers and the polymer matrix, and the porosity/defects present in the part. Chemical modification of the surface of the reinforcing fibers is an effective way of improving the fiber-polymer interaction. Furthermore, the improved adhesion between the fibers and the polymer can also enhance the fiber dispersion, improve the rheological behavior of the molten feedstock and minimize the formation of porosity during the printing process, which is one of the major issues in AM. In this study, we are investigating the effect of silane surface treatment of micro-cellulose fibers on the thermal, rheological and mechanical properties of cellulose-PLA biocomposites and on the 3D-printing process. X-ray photoelectron spectroscopy results confirmed the increase in amine and silane groups on the surface of modified fibers, indicating successful functionalization. Thermal and mechanical characterization of modified fiber-PLA composites showed significant increases in storage modulus, glass transition temperature, and complex viscosity compared to neat PLA.

Tekinalp, Halil↗

DOE OSTI2026

HYBRID COMPOSITES VIA CO-EXTRUSION ADDITIVE MANUFACTURING-COMPRESSION MOLDING FOR PERFORMANCE OPTIMIZATION

The growing demand for hybrid polymer composites with multifunctional properties has led to the development of various hybridization techniques, such as multi-material compounding and controlled laminate stacking sequence. In this study, a novel hybrid manufacturing approach was used by integrating a multiplexing extrusion system (MExS) based on additive manufacturing with subsequent compression molding process. This technique enabled the co-extrusion of different materials during the additive manufacturing process to fabricate composites with tailored performance. The developed hybrid composite featured a skin layer of glass fiberreinforced polycarbonate (PC/GF) encapsulating a carbon fiber-reinforced acrylonitrile butadiene styrene (CF/ABS) core. The structure was engineered to promote improved thermal and impact resistance at the surface, supported by a stiff core for enhanced overall mechanical integrity. Mechanical, thermal and morphological properties of the hybrid composites were investigated to understand trade-offs in performance compared to a single-material system. The results demonstrate that this approach enables the production of multifunctional composites suitable for applications such as automotive body panels and protective housings, where a balance of weight, mechanical strength, and thermal performance is essential.

Wasti, Sanjita [ORNL]↗

DOE OSTI2021

Perspectives of Open-Air Processing to Enable Perovskite Solar Cell Manufacturing

We report high throughput open-air processing techniques for the scalable production of all device and barrier layers for perovskite photovoltaics (PV). This work discusses and resolves some of the most formidable barriers to module-level scaling that the perovskite community has been facing. Our advanced technoeconomic manufacturing analysis indicates that vacuum-based processes with high capital expenditures (CapEx) and low throughputs dominate the cost of production. Open-air fabrication methods offer low CapEx routes to manufacturing, but achieving reproducibility in ambient conditions with varying relative humidity has been a persistent challenge. The use of rapid processing methods with plasma curing to convert films from the solution-state enables reproducibility, moisture immunity, and the highest perovskite PV efficiency produced in open-air. These methods are readily translatable to in-line processing where layers are sequentially deposited without the need for lengthy post-annealing steps that reduce throughput and involve additional equipment. Significant progress is demonstrated in reduced manufacturing costs as perovskites contend as a commercially viable next-generation thin film PV technology.

14 SOLAR ENERGY↗

DOE OSTI2025

Hygrothermal Aging and Thermomechanical Characterization of As-Manufactured Tidal Turbine Blade Composites

This study investigates the hygrothermal aging behavior and thermomechanical properties of as-manufactured glass fiber-reinforced epoxy and thermoplastic composite tidal turbine blades. The blades were previously deployed in a marine environment and subsequently analyzed through a comprehensive suite of material characterization techniques, including hygrothermal aging, dynamic mechanical analysis (DMA), tensile testing and X-ray computed tomography (XCT). Hygrothermal aging experiments revealed that while thermoplastic composites exhibited lower overall water absorption (0.78% vs. 0.47%), they had significantly higher diffusion coefficients than epoxy (2.1 vs. 12.1 × 10 −13 m 2 s −1 ), suggesting faster saturation in operational environments. DMA results demonstrated that water ingress caused plasticization in epoxy matrices, reducing the glass transition temperature and increasing damping (112 °C to 104 °C), while thermoplastic composites showed more stable thermal behavior (87 °C glass transition temperature). Tensile testing revealed substantial reductions in ultimate strength (>40%) for both materials after prolonged water exposure, with minimal change in elastic modulus, highlighting the role of matrix degradation over fiber reinforcement. XCT image analysis showed that both composites were manufactured with high quality: no large voids or cracks were present, and the degree of misalignment was low. These findings inform future marine renewable energy composite designs by emphasizing the critical influence of moisture on long-term structural integrity and the need for optimized material systems in harsh marine environments. This work provides a rare real-world comparison of epoxy and recyclable thermoplastic tidal turbine blades, showing how laboratory aging tests and advanced imaging reveal the influence of material and manufacturing choices on long-term marine durability.

16 TIDAL AND WAVE POWER↗

DOE OSTI2020

A Novel Laser 3D Printing Method for the Advanced Manufacturing of Protonic Ceramics

Protonic ceramics (PCs) with high proton conductivity at intermediate temperatures (300–600 °C) have attracted many applications in energy conversion and storage devices such as PC fuel/electrolysis cells, PC membrane reactors, hydrogen pump, hydrogen or water-permeable membranes, and gas sensors. One of the essential steps for fulfilling the practical utilization of these intermediate-temperature PC energy devices is the successful development of advanced manufacturing methods for cost-effectively and rapidly fabricating them with high energy density and efficiency in a customized demand. In this work, we developed a new laser 3D printing (L3DP) technique by integrating digital microextrusion-based 3D printing and precise and rapid laser processing (sintering, drying, cutting, and polishing), which showed the capability of manufacturing PCs with desired complex geometries, crystal structures, and microstructures. The L3DP method allowed the fabrication of PC parts such as pellets, cylinders, cones, films, straight/lobed tubes with sealed endings, microchannel membranes, and half cells for assembling PC energy devices. The preliminary measurement of the L3DP electrolyte film showed a high proton conductivity of ≈7 × 10−3 S/cm. This L3DP technique not only demonstrated the potential to bring the PCs into practical use but also made it possible for the rapid direct digital manufacturing of ceramic-based devices.

08 HYDROGEN↗

DOE OSTI2022

Determination of Location-Specific Solidification Cracking Susceptibility for a Mixed Dissimilar Alloy Processed by Wire-Arc Additive Manufacturing

Solidification cracking is a major obstacle when joining dissimilar alloys using additive manufacturing. In this work, location-specific solidification cracking susceptibility has been investigated using an integrated computational materials engineering (ICME) approach for a graded alloy formed by mixing P91 steel and Inconel 740H superalloy. An alloy mixture of 26 wt.% P91 and 74 wt.% Inconel 740H, with high configurational and total entropy, was fabricated using wire arc additive manufacturing. Microstructure characterization revealed intergranular solidification cracks in the FCC matrix, which increased in length along with the enrichment of Nb (~27 to 56 wt.%) and Cu (~87 wt.%) in the middle and top regions. DICTRA simulations to model location-specific solidification cracking susceptibility showed that the top region with the highest cooling rate (270 K/s) has the highest solidification cracking susceptibility in comparison with the middle and bottom regions. This is in good agreement with the experimentally observed varying crack length. From Scheil simulations, it was deduced that enrichment of Nb and Cu affected the solidification range as high as ~77%, in comparison with the matrix composition. The overall solidification cracking susceptibility and freezing range was highest for the 26 wt.% P91 alloy amongst the mixed compositions between P91 steel and 740H superalloy, proving that solidification characteristics play a major role in alloy design for additive manufacturing.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2025

Optimizing Solar PV Deployment in Manufacturing: A Morphological Matrix and Fuzzy TOPSIS Approach

The growing energy demand of the industrial sector and the need for sustainable solutions highlight the importance of efficient decision making in solar photovoltaic (PV) implementation. Selecting optimal PV configuration is complex due to the interdependent technical, economic, environmental, and social factors involved. This study introduces an integrated decision-making method combining a morphological matrix and fuzzy TOPSIS to systematically select and rank optimal PV system configurations for manufacturing firms. While the morphological matrix exhaustively examines possible design solutions based on sensing, smart, sustainable, and social (S4) attributes, the fuzzy TOPSIS method ranks the alternatives by handling uncertainty in decision making. A case study conducted in a Mexican manufacturing company validates the methodology’s effectiveness. The optimal PV configuration identified comprehensively addresses operational and sustainability criteria, covering all lifecycle stages. This approach demonstrates quantitative superiority and greater robustness compared to existing fuzzy TOPSIS-based methods for solar PV applications. The findings highlight the practical value of data-driven, multi-criteria decision making for industrial solar energy adoption, enhancing project feasibility, cost efficiency, and environmental compliance. Future research will incorporate discrete event simulation (DES) to further refine energy consumption strategies in manufacturing.

Briceño, Citlaly Pérez↗

DOE OSTI2023

Di-CNN: Domain-Knowledge-Informed Convolutional Neural Network for Manufacturing Quality Prediction

In manufacturing, convolutional neural networks (CNNs) are widely used on image sensor data for data-driven process monitoring and quality prediction. However, as purely data-driven models, CNNs do not integrate physical measures or practical considerations into the model structure or training procedure. Consequently, CNNs’ prediction accuracy can be limited, and model outputs may be hard to interpret practically. This study aims to leverage manufacturing domain knowledge to improve the accuracy and interpretability of CNNs in quality prediction. A novel CNN model, named Di-CNN, was developed that learns from both design-stage information (such as working condition and operational mode) and real-time sensor data, and adaptively weighs these data sources during model training. It exploits domain knowledge to guide model training, thus improving prediction accuracy and model interpretability. A case study on resistance spot welding, a popular lightweight metal-joining process for automotive manufacturing, compared the performance of (1) a Di-CNN with adaptive weights (the proposed model), (2) a Di-CNN without adaptive weights, and (3) a conventional CNN. The quality prediction results were measured with the mean squared error (MSE) over sixfold cross-validation. Model (1) achieved a mean MSE of 6.8866 and a median MSE of 6.1916, Model (2) achieved 13.6171 and 13.1343, and Model (3) achieved 27.2935 and 25.6117, demonstrating the superior performance of the proposed model.

47 OTHER INSTRUMENTATION↗

DOE OSTI2022

Advancing flexible electronics and additive manufacturing

There is high interest in the synergism of thin-film and flexible electronics with additive manufacturing. This review primarily focuses on the prospective developments in convergence with flexible electronics manufacturing technologies. Specifically, this paper covers the latest 3D printing and hybrid manufacturing technologies, the utility of specific types of materials, their functionalization and characterization, post-processing and testing strategies toward fabricating robust and application-specific flexible electronics. Besides exploring the advances in this area of research—it also highlights the limitations and gaps that have been observed in the previous years that will challenge and offer opportunities for advancing research and development. Lastly, the future of 3D-printed flexible electronics is discussed in the aspects of customizability, scalability, and its game-changing and state-of-the-art potential for intelligent sensing, instrumentation, and wearables for various medical, engineering, and industrial applications.

36 MATERIALS SCIENCE↗

DOE OSTI2026

AMVOS: Additive Manufacturing Video Object Segmentation Dataset

This dataset provides labeled video frames from four additive manufacturing (AM) processes for video object segmentation (VOS) tasks. It contains 90 video segments comprising 900 individually annotated frames across five AM datasets: laser hot-wire directed energy deposition (LHW-DED), tungsten inert gas wire arc additive manufacturing (TIG-WAAM), plasma arc welding (PAW), visible-light polymer extrusion (visPolymer), and near-infrared polymer extrusion (irPolymer). Each video segment consists of 10 contiguous frames with corresponding pixel-level object instance annotations. Depending on the process, two of four object classes are labeled per frame: Melt Pool, Feed Wire, Nozzle, or Material. Raw frames are provided as .jpg files and annotations as palettized .png files. The dataset follows the directory structure of established VOS benchmarks (DAVIS, YouTube-VOS, MOSE), enabling direct integration into VOS model training and evaluation pipelines for foundation model fine-tuning, domain adaptation, or zero-shot performance benchmarking. Data was collected at Oak Ridge National Laboratory's Manufacturing Demonstration Facility.

Wetzel, Jon [ORNL]↗

NASA NTRS1971

Pyrotechnic hazards classification and evaluation program. Phase 2, segment 3: Test plan for determining hazards associated with pyrotechnic manufacturing processes

A comprehensive test plan for determining the hazards associated with pyrotechnic manufacturing processes is presented. The rationale for each test is based on a systematic analysis of historical accounts of accidents and a detailed study of the characteristics of each manufacturing process. The most hazardous manufacturing operations have been determined to be pressing, mixing, reaming, and filling. The hazard potential of a given situation is evaluated in terms of the probabilities of initiation, communication, and transition to detonation (ICT). The characteristics which affect the ICT probabilities include the ignition mechanisms which are present either in normal or abnormal operation, the condition and properties of the pyrotechnic material, and the configuration of the processing equipment. Analytic expressions are derived which describe the physical conditions of the system, thus permitting a variety of processes to be evaluated in terms of a small number of experiments.

Source record↗

NASA NTRS1972

Ablator manufacturing

Studies are being conducted to determine how manufacturing-induced defects affect the performance of ablative heat shields. If commonly occurring defects do not affect material performance, simpler manufacturing techniques can be used, quality control requirements can be relaxed, repair and rework operations can be held to a minimum, and thus the total manufacturing cost can be reduced.

Pittman, C. M.↗