Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MATING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74

Tungsten Incorporation into Gallium Oxide: Crystal Structure, Surface and Interface Chemistry, Thermal Stability and Interdiffusion

Tungsten (W) incorporated gallium oxide (Ga2O3) (GWO) thin films were deposited by radio-frequency magnetron co-sputtering of W-metal and Ga2O3-ceramic targets. Films were produced by varying sputtering power applied to the W-target in order to achieve variable W-content (0-12 at%) into Ga2O3 while substrate temperature was kept constant at 500 °C. Chemical composition, chemical valence states, microstructure and crystal structure of as-deposited and annealed GWO films were evaluated as a function of W-content. The structural and chemical analyses indicate that the samples deposited without any W-incorporation are stoichiometric, nanocrystalline Ga2O3 films, which crystallize in β-phase monoclinic structure. While GWO films also crystallize in monoclinic β-Ga2O3 phase, W-incorporation induces surface amorphization as revealed by structural studies. The chemical valence state of Ga ions probed by X-ray photoelectron spectroscopic (XPS) analyses is characterized by the highest oxidation state i.e., Ga3+. No changes in Ga chemical state are noted for variable W-incorporation in the range of 0-12 at%. Rutherford backscattering spectrometry (RBS) analyses indicate the uniform distribution of W-content in the GWO films. However, XPS analyses indicate the formation of mixed valence states for W ions, which may be responsible for surface amorphization in GWO films. GWO films were stable up to 900 oC, at which point thermally induced secondary phase (W-oxide) formation was observed. A transition to mesoporous structure coupled with W interdiffusion occurs due to thermal annealing as derived from the chemical analyses at the GWO films’ surface as well as depth-profiling towards the GWO-Si interface. A model has been formulated to account for the mechanism of W-incorporation, thermal stability and interdiffusion via pore formation in GWO films.

Chemical composition↗

Moiré-Assisted Strain Transfer in Vertical van der Waals Heterostructures

Strain provides a powerful method to study 2D monolayers and to tune their properties. The same approach also has great potential for van-der-Waals (vdW) heterostructures. However, we need to understand how strain can be applied to vertically stacked vdW structures, for which strain transfer from one layer to the next remains little explored. In our experiment, we fabricated vertical heterostructures consisting of transition metal dichalcogenides (TMDCs) monolayers that were deposited on a flexible substrate. These TMDC heterostructures allowed us to read out separately the strain in each monolayer by photoluminescence measurements. We find that, in TMDC heterostructures with large twist angles (>5°), strain transfer is limited. However, for aligned heterostructures with small twist angles (≤5°), near unity strain transfer efficiency is observed. Here, we correlate this finding with the moiré domains formed in the aligned heterostructures by reconstruction.

2D materials↗

Selective ion transport through hydrated micropores in polymer membranes

Abstract Ion-conducting polymer membranes are essential in many separation processes and electrochemical devices, including electrodialysis 1 , redox flow batteries 2 , fuel cells 3 and electrolysers 4,5 . Controlling ion transport and selectivity in these membranes largely hinges on the manipulation of pore size. Although membrane pore structures can be designed in the dry state 6 , they are redefined upon hydration owing to swelling in electrolyte solutions. Strategies to control pore hydration and a deeper understanding of pore structure evolution are vital for accurate pore size tuning. Here we report polymer membranes containing pendant groups of varying hydrophobicity, strategically positioned near charged groups to regulate their hydration capacity and pore swelling. Modulation of the hydrated micropore size (less than two nanometres) enables direct control over water and ion transport across broad length scales, as quantified by spectroscopic and computational methods. Ion selectivity improves in hydration-restrained pores created by more hydrophobic pendant groups. These highly interconnected ion transport channels, with tuned pore gate sizes, show higher ionic conductivity and orders-of-magnitude lower permeation rates of redox-active species compared with conventional membranes, enabling stable cycling of energy-dense aqueous organic redox flow batteries. This pore size tailoring approach provides a promising avenue to membranes with precisely controlled ionic and molecular transport functions.

Science & Technology - Other Topics↗

Combined experimental-theoretical study of electron mobility-limiting mechanisms in SrSnO 3

The discovery and development of ultra-wide bandgap (UWBG) semiconductors is crucial to accelerate the adoption of renewable power sources. This necessitates an UWBG semiconductor that exhibits robust doping with high carrier mobility over a wide range of carrier concentrations. Here we demonstrate that epitaxial thin films of the perovskite oxide Nd x Sr 1 – x SnO 3 (SSO) do exactly this. Nd is used as a donor to successfully modulate the carrier concentration over nearly two orders of magnitude, from 3.7 × 10 18 cm –3 to 2.0 × 10 20 cm –3 . Despite being grown on lattice-mismatched substrates and thus having relatively high structural disorder, SSO films exhibited the highest room-temperature mobility, ~70 cm 2 V –1 s –1 , among all known UWBG semiconductors in the range of carrier concentrations studied. The phonon-limited mobility is calculated from first principles and supplemented with a model to treat ionized impurity and Kondo scattering. This produces excellent agreement with experiment over a wide range of temperatures and carrier concentrations, and predicts the room-temperature phonon-limited mobility to be 76–99 cm 2 V –1 s –1 depending on carrier concentration. This work establishes a perovskite oxide as an emerging UWBG semiconductor candidate with potential for applications in power electronics

36 MATERIALS SCIENCE↗

Tethered tertiary amines as solid-state n-type dopants for solution-processable organic semiconductors

A scarcity of stable n-type doping strategies compatible with facile processing has been a major impediment to the advancement of organic electronic devices. Localizing dopants near the cores of conductive molecules can lead to improved efficacy of doping. We and others recently showed the effectiveness of tethering dopants covalently to an electron-deficient aromatic molecule using trimethylammonium functionalization with hydroxide counterions linked to a perylene diimide core by alkyl spacers. In this work, we demonstrate that, contrary to previous hypotheses, the main driver responsible for the highly effective doping observed in thin films is the formation of tethered tertiary amine moieties during thin film processing. Furthermore, we demonstrate that tethered tertiary amine groups are powerful and general n-doping motifs for the successful generation of free electron carriers in the solid-state, not only when coupled to the perylene diimide molecular core, but also when linked with other small molecule systems including naphthalene diimide, diketopyrrolopyrrole, and fullerene derivatives. Our findings help expand a promising molecular design strategy for future enhancements of n-type organic electronic materials.

36 MATERIALS SCIENCE↗

Diffusion of Brønsted acidic dopants in conjugated polymers

Many semiconductor devices (e.g., light emitting diodes and photovoltaics) utilize heterojunctions of doped and undoped layers or depend on gradients of electronic doping to control charge transport. Understanding of the formation and stability of gradients in doping requires an understanding of diffusion of dopants and the complex changes in polymer properties that arise during doping. Conjugated polymers can be electrically doped by strong acids, but the details of the reaction mechanism and subsequent stability are not understood. Here, we show a clear kinetic isotope effect in the doping of thin films of poly(3-hexylthiophene) (P3HT) by bis(trifluoromethane)sulfonimide (HTFSI) from solution indicating that this doping process is limited by proton transfer to the polymer. Complementary X-ray photoelectron spectroscopy and dynamic secondary ion mass spectrometry (DSIMS) depth profiling of dopant concentrations show definitive evidence of dopant enrichment at the P3HT surface. These surface-limited concentration profiles suggest that diffusivity of dopants vary inversely with dopant concentration due to doping-induced changes to the structure of the conjugated polymer.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High electron mobility GaN grown under N-rich conditions by plasma-assisted molecular beam epitaxy

An alternative approach is presented for the plasma-assisted molecular beam epitaxy of high-quality GaN. Under N-rich growth conditions, an unexpected layer-by-layer growth mode was found for a wide range of growth temperatures in the GaN thermal decomposition regime (>750 deg. C). Consequently, superior surface morphologies with roughness of less than 1 nm (rms) have been achieved. For lightly Si-doped GaN films, room-temperature electron mobilities exceeding 1100 cm{sup 2}/V s were measured, surpassing the commonly insulating nature of GaN grown under N-rich conditions at low temperature.

36 MATERIALS SCIENCE↗

Polarity inversion of N-face GaN by plasma-assisted molecular beam epitaxy

The polarity of GaN grown by plasma-assisted molecular beam epitaxy was inverted from N-face to Ga-face by simultaneously exposing the surface to Mg and activated N fluxes during a growth interruption at a reduced substrate temperature. Growth studies suggested that a Mg{sub x}N{sub y} compound was responsible for inverting the crystal. The change in polarity was verified in situ by reflection high energy electron diffraction via GaN surface reconstructions, and ex situ by convergent beam electron diffraction and KOH etch studies. The surface of the inverted material showed smooth step flow features. Ga-face high electron mobility transistors with good dc and small signal performance were fabricated on the inverted epilayers. A drain-source current of 0.84 A/mm was measured at a gate-source voltage of +1 V. Current-gain cutoff and maximum oscillation frequencies of 22 and 53 GHz, respectively, were measured in these devices. The device performance is similar to that of Ga-face transistors with comparable dimensions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Static and Dynamic Viscosity of a Single Layer Dusty Plasma

We measured the static and dynamic (complex) shear viscosity of a single layer complex plasma by applying, respectively, a stationary and a periodically modulated shear stress induced by the light pressure of manipulating laser beams. Under static conditions the shear viscosity reproduced the numerically predicted shear rate dependence, the so called shear-thinning effect. Under oscillating shear both the magnitude and the ratio of the dissipative and elastic contributions to the complex viscosity show strong frequency dependence. Accompanying molecular dynamics simulations explain and support the experimental observations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A high resolution gamma-ray spectrometer based on superconducting microcalorimeters

Improvements in superconductor device fabrication, detector hybridization techniques, and superconducting quantum interference device readout have made square-centimeter-sized arrays of gamma-ray microcalorimeters, based on transition-edge sensors (TESs), possible. At these collecting areas, gamma microcalorimeters can utilize their unprecedented energy resolution to perform spectroscopy in a number of applications that are limited by closely-spaced spectral peaks, for example, the nondestructive analysis of nuclear materials. We have built a 256 pixel spectrometer with an average full-width-at-half-maximum energy resolution of 53 eV at 97 keV, a useable dynamic range above 400 keV, and a collecting area of 5 cm{sup 2}. We have demonstrated multiplexed readout of the full 256 pixel array with 236 of the pixels (91%) giving spectroscopic data. This is the largest multiplexed array of TES microcalorimeters to date. This paper will review the spectrometer, highlighting the instrument design, detector fabrication, readout, operation of the instrument, and data processing. Further, we describe the characterization and performance of the newest 256 pixel array.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Influence of plasma-based in-situ surface cleaning procedures on HfO{sub 2}/In{sub 0.53}Ga{sub 0.47}As gate stack properties

We report on the influence of variations in the process parameters of an in-situ surface cleaning procedure, consisting of alternating cycles of nitrogen plasma and trimethylaluminum dosing, on the interface trap density of highly scaled HfO{sub 2} gate dielectrics deposited on n-In{sub 0.53}Ga{sub 0.47}As by atomic layer deposition. We discuss the interface chemistry of stacks resulting from the pre-deposition exposure to nitrogen plasma/trimethylaluminum cycles. Measurements of interface trap densities, interface chemistry, and surface morphology show that variations in the cleaning process have a large effect on nucleation and surface coverage, which in turn are crucial for achieving low interface state densities.

36 MATERIALS SCIENCE↗

High-resolution gamma-ray spectroscopy with a microwave-multiplexed transition-edge sensor array

We demonstrate very high resolution photon spectroscopy with a microwave-multiplexed two-pixel transition-edge sensor (TES) array. We measured a {sup 153}Gd photon source and achieved an energy resolution of 63 eV full-width-at-half-maximum at 97 keV and an equivalent readout system noise of 86 pA/√(Hz) at the TES. The readout circuit consists of superconducting microwave resonators coupled to radio-frequency superconducting-quantum-interference-devices and transduces changes in input current to changes in phase of a microwave signal. We use flux-ramp modulation to linearize the response and evade low-frequency noise. This demonstration establishes one path for the readout of cryogenic X-ray and gamma-ray sensor arrays with more than 10{sup 3} elements and spectral resolving powers R=λ/Δλ>10{sup 3}.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Scaled ZrO{sub 2} dielectrics for In{sub 0.53}Ga{sub 0.47}As gate stacks with low interface trap densities

ZrO{sub 2} dielectrics were grown on n-In{sub 0.53}Ga{sub 0.47}As channels by atomic layer deposition, after employing an in-situ cyclic nitrogen plasma/trimethylaluminum surface cleaning procedure. By scaling the ZrO{sub 2} thickness, accumulation capacitance densities of 3.5 μF/cm{sup 2} at 1 MHz are achieved. The midgap interface trap density is estimated to be in the 10{sup 12} cm{sup −2} eV{sup −1} range. Using x-ray photoelectron spectroscopy, it was shown that the interface contained the oxides of In, Ga, and Al, but no As-oxides or As-As bonds within the detection limit. The results allow for insights into the effective passivation of these interfaces.

36 MATERIALS SCIENCE↗

Extremely scaled high-k/In₀.₅₃Ga₀.₄₇As gate stacks with low leakage and low interface trap densities

Highly scaled gate dielectric stacks with low leakage and low interface trap densities are required for complementary metal-oxide-semiconductor technology with III-V semiconductor channels. Here, we show that a novel pre-deposition technique, consisting of alternating cycles of nitrogen plasma and tetrakis(dimethylamino)titanium, allows for HfO₂ and ZrO₂ gate stacks with extremely high accumulation capacitance densities of more than 5 μF/cm₂ at 1 MHz, low leakage current, low frequency dispersion, and low midgap interface trap densities (10¹²cm⁻²eV⁻¹range). Using x-ray photoelectron spectroscopy, we show that the interface contains TiO₂ and small quantities of In₂O₃, but no detectable Ga- or As-oxides, or As-As bonding. The results allow for insights into the microscopic mechanisms that control leakage and frequency dispersion in high-k/III-V gate stacks.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The electrochemical impact on electrostatic modulation of the metal-insulator transition in nickelates

For physical studies of correlated electron systems and for realizing novel device concepts, electrostatic modulation of metal-insulator transitions (MITs) is desired. The inherently high charge densities needed to modulate MITs make this difficult to achieve. The high capacitance of ionic liquids are attractive but, voltages are needed that can be in excess of the electrochemical stability of the system. Here, we show temperature/resistivity data that suggest electrostatic modulation of the MIT temperature of NdNiO{sub 3} in a wide regime. However, additional voltammetric and x-ray photoelectron spectroscopy measurements demonstrate the electrochemical impact of the electrostatic doping approach with ionic liquids.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Calcium impurity as a source of non-radiative recombination in (In,Ga)N layers grown by molecular beam epitaxy

Ca as an unintentional impurity has been investigated in III-nitride layers grown by molecular beam epitaxy (MBE). It has been found that Ca originates from the substrate surface, even if careful cleaning and rinsing procedures are applied. The initial Ca surface coverage is ~10 12 cm -2 , which is consistent with previous reports on GaAs and silicon wafers. At the onset of growth, the Ca species segregates at the growth front while incorporating at low levels. The incorporation rate is strongly temperature dependent. It is about 0.03% at 820 °C and increases by two orders of magnitude when the temperature is reduced to 600 °C, which is the typical growth temperature for InGaN alloy. Consequently, [Ca] is as high as 10 18 cm -3 in InGaN/GaN quantum well structures. Such a huge concentration might be detrimental for the efficiency of light emitting diodes (LEDs) if one considers that Ca is potentially a source of Shockley-Read-Hall (SRH) defects. We thus developed a specific growth strategy to reduce [Ca] in the MBE grown LEDs, which consisted of burying Ca in a low temperature InGaN/GaN superlattice (SL) before the growth of the active region. Finally, two LED samples with and without an SL were fabricated. An increase in the output power by one order of magnitude was achieved when Ca was reduced in the LED active region, providing evidence for the role of Ca in the SRH recombination.

36 MATERIALS SCIENCE↗