Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Gas Separation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74
All sourcesNASA NTRSDOE OSTI
NASA NTRS2002

Parametric Time-Dependent Navier-Stokes Computations for a YAV-8B Harrier in Ground Effect

The Harrier Jump Jet has the distinction of being the only powered-lift aircraft in the free world to achieve operational status and to have flown in combat. This V/STOL aircraft can take-off and land vertically or utilize very short runways by directing its four exhaust nozzles towards the ground. Transition to forward flight is achieved by rotating these nozzles into a horizontal position. Powered-lift vehicles have certain advantages over conventional strike fighters. Their V/STOL capabilities allow for safer carrier operations, smaller carrier size, and quick reaction time for troop support. Moreover, they are not dependent on vulnerable land-based runways. The AV-8A Harrier first entered service in the British Royal Air Force (RAF) during 1969, and the U.S. Marine Corps (USMC) in 1971. The AV-8B was a redesign to achieve improved payload capacity, range, and accuracy. This modified design first entered service with the USMC and RAF in 1985. The success and unique capabilities of the Harrier has prompted the design of a powered-lift version of the Joint Strike Fighter (JSF). The flowfield for the Harrier near the ground during low-speed or hover flight operations is very complex and time-dependent. A sketch of this flowfield is shown. Warm air from the fan is exhausted from the front nozzles, while a hot air/fuel mixture from the engine is exhausted from the rear nozzles. These jets strike the ground and move out radially forming a ground jet-flow. The ambient freestream, due to low-speed forward flight or - headwind during hover, opposes the jet-flow. This interaction causes the flow to separate and form a ground vortex. The multiple jets also interact with each other near the ground and form an upwash or jet fountain, which strikes the underside of the fuselage. If the aircraft is sufficiently close to the ground, the inlet can ingest ground debris and hot gases from the fountain and ground vortex. This Hot Gas Ingestion (HGI) can cause a sudden loss of thrust (powered lift), and the vehicle may crash. The high-speed jet flow along the ground can also entrain the ambient flow, resulting in a low pressure region underneath the vehicle. The accompanied loss of lift is referred to as the suckdown effect. The ground vortex may also be highly unsteady, dramatically changing its size and position with time at low frequencies, e.g., 1 Hz.

Chaderjian, Neal M.↗
NASA NTRS2010

NASA Tech Briefs, April 2010

Topics covered include: Active and Passive Hybrid Sensor; Quick-Response Thermal Actuator for Use as a Heat Switch; System for Hydrogen Sensing; Method for Detecting Perlite Compaction in Large Cryogenic Tanks; Using Thin-Film Thermometers as Heaters in Thermal Control Applications; Directional Spherical Cherenkov Detector; AlGaN Ultraviolet Detectors for Dual-Band UV Detection; K-Band Traveling-Wave Tube Amplifier; Simplified Load-Following Control for a Fuel Cell System; Modified Phase-meter for a Heterodyne Laser Interferometer; Loosely Coupled GPS-Aided Inertial Navigation System for Range Safety; Sideband-Separating, Millimeter-Wave Heterodyne Receiver; Coaxial Propellant Injectors With Faceplate Annulus Control; Adaptable Diffraction Gratings With Wavefront Transformation; Optimizing a Laser Process for Making Carbon Nanotubes; Thermogravimetric Analysis of Single-Wall Carbon Nanotubes; Robotic Arm Comprising Two Bending Segments; Magnetostrictive Brake; Low-Friction, Low-Profile, High-Moment Two-Axis Joint; Foil Gas Thrust Bearings for High-Speed Turbomachinery; Miniature Multi-Axis Mechanism for Hand Controllers; Digitally Enhanced Heterodyne Interferometry; Focusing Light Beams To Improve Atomic-Vapor Optical Buffers; Landmark Detection in Orbital Images Using Salience Histograms; Efficient Bit-to-Symbol Likelihood Mappings; Capacity Maximizing Constellations; Natural-Language Parser for PBEM; Policy Process Editor for P(sup 3)BM Software; A Quality System Database; Trajectory Optimization: OTIS 4; and Computer Software Configuration Item-Specific Flight Software Image Transfer Script Generator.

Source record↗
NASA NTRS2012

A Computational Study for the Utilization of Jet Pulsations in Gas Turbine Film Cooling and Flow Control

This report is the second part of a three-part final report of research performed under an NRA cooperative Agreement contract. The first part is NASA/CR-2012-217415. The third part is NASA/CR-2012-217417. Jets have been utilized in various turbomachinery applications in order to improve gas turbines performance. Jet pulsation is a promising technique because of the reduction in the amount of air removed from compressor. In this work two areas of pulsed jets applications were computationally investigated using the commercial code Fluent (ANSYS, Inc.); the first one is film cooling of High Pressure Turbine (HPT) blades and second one is flow separation control over Low Pressure Turbine (LPT) airfoil using Vortex Generator Jets (VGJ). Using pulsed jets for film cooling purposes can help to improve the effectiveness and thus allow higher turbine inlet temperature. Effects of the film hole geometry, blowing ratio and density ratio of the jet, pulsation frequency and duty cycle of blowing on the film cooling effectiveness were investigated. As for the low-pressure turbine (LPT) stages, the boundary layer separation on the suction side of airfoils can occur due to strong adverse pressure gradients. The problem is exacerbated as airfoil loading is increased. Active flow control could provide a means for minimizing separation under conditions where it is most severe (low Reynolds number), without causing additional losses under other conditions (high Reynolds number). The effects of the jet geometry, blowing ratio, density ratio, pulsation frequency and duty cycle on the size of the separated region were examined in this work. The results from Reynolds Averaged Navier-Stokes and Large Eddy Simulation computational approaches were compared with the experimental data.

Kartuzova, Olga V.↗
NASA NTRS2018

Extraction of Water from Martian Regolith Simulant via Open Reactor Concept

To demonstrate proof of concept water extraction from simulated Martian regolith, an open reactor design is presented along with experimental results. The open reactor concept avoids sealing surfaces and complex moving parts. In an abrasive environment like the Martian surface, those reactor elements would be difficult to maintain and present a high probability of failure. A general lunar geotechnical simulant was modified by adding borax decahydrate (Na2B4O7·10H2O) (BDH) to mimic the ~ 3 percent water content of hydrated salts in near surface soils on Mars. A rotating bucket wheel excavated the regolith from a source bin and deposited the material onto an inclined copper tray, which was fitted with heaters and a simple vibration system. The combination of vibration, tilt angle and heat was used to separate and expose as much regolith surface area as possible to liberate the water contained in the hydrated minerals, thereby increasing the efficiency of the system. The experiment was conducted in a vacuum system capable of maintaining a Martian like atmosphere. Evolved water vapor was directed to a condensing system using the ambient atmosphere as a sweep gas. The water vapor was condensed and measured. Processed simulant was captured in a collection bin and weighed in real time. The efficiency of the system was determined by comparing pre- and post-processing soil mass along with the volume of water captured.

Trunek, Andrew J.↗
NASA NTRS2019

Cosmic Pathways for Compact Groups in the Milli-Millennium Simulation

We detected 10 compact galaxy groups (CGs) at z=0 in the semianalytic galaxy catalog of Guo et al. for themilli-Millennium Cosmological Simulation (sCGs in mGuo2010a). We aimed to identify potential canonicalpathways for compact group evolution and thus illuminate the history of observed nearby CGs. By constructingmerger trees for z=0 sCG galaxies, we studied the cosmological evolution of key properties and compared themwith z=0 Hickson CGs (HCGs). We found that, once sCG galaxies come within 1 (0.5) Mpc of their mostmassive galaxy, they remain within that distance until z=0, suggesting sCG "birth redshifts." At z=0 stellarmasses of sCG most massive galaxies are within 1010M*/Me1011. In several cases, especially in the twofour- and five-member systems, the amount of cold gas mass anticorrelates with stellar mass, which in turncorrelates with hot gas mass. We define the angular difference between group members' 3D velocity vectors,vel, and note that many of the groups are long-lived because their small values of vel indicate a significantparallel component. For triplets in particular, vel values range between 20° and 40° so that galaxies are comingtogether along roughly parallel paths, and pairwise separations do not show large pronounced changes after closeencounters. The best agreement between sCG and HCG physical properties is for M* galaxy values, but HCGvalues are higher overall, including for star formation rates (SFRs). Unlike HCGs, due to a tail at low SFR and M*and a lack of M*1011Me galaxies, only a few sCG galaxies are on the star-forming main sequence

Tzanavaris, Panayiotis↗
NASA NTRS2020

Multibody Simulation of REMORA CubeSat Docking to and Pushing a Spent Rocket Booster

This paper details the multibody simulation of three phases of critical importance to the feasibility of the REMORA CubeSat space debris mitigation concept: the final approach of the CubeSat to a spent rocket booster; the grappling of the spent rocket booster using a robotic arm; and the pushing of the spent rocket booster to divert its course from another on-orbit asset. The extension of a robotic mobility and manipulation modeling toolkit (M3TK) from multibody dynamics simulation of manipulators and ground vehicles to simulation of orbital robotics is outlined. This includes the identification of the appropriate parameters required to concisely and generically describe thruster loads, thruster mixing, spacecraft control, and spacecraft navigation for the purpose of on-orbit robotics simulation. A high-level spacecraft navigator commands maneuvers to target spacecraft states. A PID spacecraft controller takes the target states and calculates desired forces and torques. A thruster mixer solves a quadratic program to determine the optimal thruster firing times for the propulsion system. Pulse width modulated actuation of eight canted cold gas thrusters is used in the simulated approach to a rocket nozzle from a distance of 200 m. A five degree of freedom robotic arm is controlled to position a pair of pincers to grasp the rocket nozzle. Contact dynamics are used to accurately simulate the grasping of the rocket nozzle by the pincers. A similar, but separate simulation is performed to assess the ability of the REMORA CubeSat to push the large spent rocket booster. This diversion maneuver makes use of an additional, larger thruster, and pushes the rocket booster in excess of 400 m. Appropriate motor control gains on the robotic arm are found to be higher during the pushing phase than those which are appropriate during free motion; this increase promotes rigidity of the arm and allows it to properly direct the pushing force. Challenges encountered in time step selection for numerical stability of the simulation are also discussed.

Mukherjee, Rudranarayan↗
NASA NTRSDate not supplied

X-Ray Computed Tomography During Preliminary Examination of Apollo Drive Tube 73001

Introduction: Starting in 2019, the Apollo Next Generation Sample Analysis (ANGSA) Program has enabled consortium studies of specially curated Apollo samples that were previously unstudied (or under studied). This began with unsealed core tube 73002 [1,2] that is the upper part of a station 3 double drive tube. More recently the pro-gram extended to the study of a variety of frozen Apollo 17 samples [3], as well as the gas extraction [4] and dis-section [5] of 73001, the lower half of the station 3 double drive tube, that was sealed under vacuum on the Moon. In this abstract we will examine the role of X-ray Computed Tomography (XCT) during the preliminary examination process for sealed core 73001, including: (1) engineering scans to aid in understanding the gas extraction process, whole-core scanning prior to opening to inform extrusion and dissection work, and (3) individual particle scanning to characterize rock fragment lithologies for follow on studies. Methodology: Sample 73001 is a 33 cm long, 4 cm diameter regolith sample collected inside a drive tube (~1 mm aluminum walls). That drive tube was sealed inside a 0.5 mm thick stainless steel (SS) Core Sample Vacuum Container (CSVC). XCT scans for engineering purposes were done on the Nikon XTH 320 system at Johnson Space Center using the 225 kV multi-metal reflection source at 215 kV, 179 A, and a 38.49 m voxel size. Individual >4 mm particles separated from the core during processing (then triply sealed in Teflon bags) were also scanned at JSC using the 180 kV source at 90 kV, 33 A, and a 2.98 – 10.65 m voxel size. Whole-core scans were done at the University of Texas High-Resolution X-ray Computed Tomography Facility (UTCT) on the 225 kV reflection source on the North Star Imaging cabinet XCT system. These scans included: (1) a series of 9 overlapping super-resolution scans each covering a ~4 cm length of the tube at 190 kV, 180 µA, and a 12.9 µm voxel size and (2) a lower resolution continuous helical scan of the entire core at 190 kV, 180 µA, and a 51.8 µm voxel size. Progress and Results: Before piercing and extracting the gas from sample 73001, an XCT scan of the bottom portion of the CSVC was used to confirm the location of the Teflon cap on the inner drive tube, to ensure it was not accidentally pierced during gas extraction. Similarly, after piercing, the bottom and top portions of the CSVC were scanned in order to capture engineering knowledge about the results of the piercing process, as well as the metal knife edge vacuum seal (SS into In-Ag alloy). Both scans will provide constraints on future work of this type, particularly for samples collected during the Artemis mission. Another finding from these "engineering" scans was that the device in the drive tube that immobilizes the regolith (the keeper) was not seated in the tube properly. This meant that (1) the drive tube could not be removed from the CSVC for the trip to UTCT, and (2) the procedure for opening and extruding the drive tube had to be modified. Had either of these things not been known prior to opening the CSVC, it could have led to an inability to XCT scan the whole core at high resolution and/or potential disruption of the core stratigraphy during extrusion. At UTCT, the entire length of the core was scanned at high resolution (12.9 microns per voxel). This scan serves multiple purposes: (1) A lower resolution (and uncorrected) version of these scans stitched together was used to help inform the processors of potential pitfalls during extrusion and dissection; and (2) the full resolution corrected data will serve as the permanent in situ record of the stratigraphy of the sample and will enable future researchers to perform a variety of analyses. So far, 92 of the 121 >4 mm particles separated during dissection pass 1 of sample 73001 have been individually scanned. These scans clearly show the lithology of each particle while keeping the particles in pristine condition. Because of the dust adhering to particle exteriors it would otherwise be impossible to determine lithologies in a non-contaminating way. Thus far the types of lithologies seen in sample 73001 (e.g., regolith breccias, impact-melt breccias, agglutinates, and basalts) are similar to those previously identified in sample 73002 [2]. By the time of the meeting, all particles from all 3 dissection passes will have been scanned and statistics on the different lithologies in 73001 compiled. References: [1] Shearer et al. (2020) 51st LPSC, abstract 1181. [2] Zeigler et al. (2020) 51st LPSC, abstract 3023. [3] Kent et al. (2022) This Volume. [4] McDonald et al. (2022) European Lunar Symposium. [5] Gross et al (2022) This volume.

Moon↗
NASA NTRS1973

A thick-thin approximation for radiative transfer.

First- and second-order formulations of a thick-thin approximate technique for application to the solution of energy transport when nongray radiation is important are presented. The virtue of the technique is that it eliminates the cumbersome integral terms which usually appear. It is shown that the temperature distributions calculated with the technique agree well with the results of more rigorous calculations if a proper value of the critical optical depth, which separates the thick and thin regions of the spectrum, is used. The proper value of the critical optical depth is less than one and may be less than 0.5. It is also shown that the jump boundary conditions which are frequently employed with the Rosseland, or diffusion, approximation should incorporate the Planck mean absorption coefficient for a nongray gas. This is in contradiction to suggestions appearing in the literature.

Olstad, W. B.↗
NASA NTRS1974

Flight Reynolds number effects on a contoured boattail nozzle at subsonic speeds

A contoured boattail nozzle typical of those used on a twin-engine fighter was tested on an underwing nacelle mounted on an F-106B aircraft. The gas generator was a J85-GE-13 turbojet engine. The effects of Reynolds number, Mach number, and angle of attack on boattail drag and boattail pressure profiles were investigated. Increasing Reynolds number caused a slight reduction in boattail drag at both Mach 0.7 and 0.9. The nozzle had relatively low boattail drag even though the flow was separated over a large portion of the boattail.

Chamberlin, R.↗
NASA NTRS1975

Study of a porous surface microphone sensor in an aerofoil

The porous microphone in an airfoil is described as a directional sensor which rejects flow noise. The airfoil allows the sensor to be rotated in the airflow over a wide range of yaw angles, 0 to 90 degrees, avoiding flow separation over the surface of the sensor and its associated additional flow noise. The microphone is discussed in terms of its acoustic properties, vibration sensitivity, effect of Mach number on the directivity function, and flow noise. Additional information on the acoustic calibration of the microphone, the acceleration sensitivity of the airfoil, stationary source and receiver in a moving gas, acoustic tests in airflow, and flow noise tests of the airfoil porous surface sensor is included.

Noiseux, D. U.↗
NASA NTRS1979

Nuclear-pumped CO2 laser

The He-3 (n,p)T reaction was examined as an energy source for a CO2 laser. For this purpose He-3 was added to a functioning CO2 electrically excited laser. Initially the laser was run electrically with 12 torr total pressure. The gas mixture was 1:1:8, CO2:N2:He. At zero reactor power, the laser was tested in place next to the core of the Georgia Tech. Research Reactor. After verification of laser action He-3 was added to the system. The He-3 partial pressures of 10 torr, 50 torr, and 300 torr were added in three separate reactor runs. Reactor power ranged from zero to 5 million watts, which corresponds to a peak flux of 10 to the 14th power/sq cm. At reactor powers greater than 10 kW, gain of up to 30 percent was shown. However, indications are this may be due to gamma excitation rather than caused by the He-3 (n,p)T reaction. These results do agree with the data of past CO2 nuclear pumped laser experiments.

Rowe, M.↗
NASA NTRS1984

Structure of nonevaporating sprays - Measurements and predictions

Structure measurements were completed within the dilute portion of axisymmetric nonevaporating sprays (SMD of 30 and 87 microns) injected into a still air environment, including: mean and fluctuating gas velocities and Reynolds stress using laser-Doppler anemometry; mean liquid fluxes using isokinetic sampling; drop sizes using slide impaction; and drop sizes and velocities using multiflash photography. The new measurements were used to evaluate three representative models of sprays: (1) a locally homogeneous flow (LHF) model, where slip between the phases was neglected; (2) a deterministic separated flow (DSF) model, where slip was considered but effects of drop interaction with turbulent fluctuations were ignored; and (3) a stochastic separated flow (SSF) model, where effects of both interphase slip and turbulent fluctuations were considered using random sampling for turbulence properties in conjunction with random-walk computations for drop motion. The LHF and DSF models were unsatisfactory for present test conditions-both underestimating flow widths and the rate of spread of drops. In contrast, the SSF model provided reasonably accurate predictions, including effects of enhanced spreading rates of sprays due to drop dispersion by turbulence, with all empirical parameters fixed from earlier work.

Solomon, A. S. P.↗
NASA NTRS1988

Slip effects associated with Knudsen transport phenomena in porous media

Porous media used in phase separators and thermomechanical pumps have been the subject of characterization efforts based on the Darcy permeability of laminar continuum flow. The latter is not always observed at low speed, in particular at permeabilities below 10 to the -9th/squared cm. The present experimental and theoretical studies address questions of slip effects associated with long mean free paths of gas flow at room temperature. Data obtained are in good agreement, within data uncertainty, with a simplified asymptotic Knudsen equation proposed for porous plugs on the basis of Knudsen's classical flow equation for long mean free paths.

Frederking, T. H. K.↗
NASA NTRS1993

The H + OCS hot atom reaction - CO state distributions and translational energy from time-resolved infrared absorption spectroscopy

Time-resolved infrared diode laser spectroscopy has been used to probe CO internal and translational excitation from the reaction of hot H atoms with OCS. Product distributions should be strongly biased toward the maximum 1.4 eV collision energy obtained from 278 nm pulsed photolysis of HI. Rotations and vibrations are both colder than predicted by statistical density of states theory, as evidenced by large positive surprisal parameters. The bias against rotation is stronger than that against vibration, with measurable population as high as v = 4. The average CO internal excitation is 1920/cm, accounting for only 13 percent of the available energy. Of the energy balance, time-resolved sub-Doppler line shape measurements show that more than 38 percent appears as relative translation of the separating CO and SH fragments. Studies of the relaxation kinetics indicate that some rotational energy transfer occurs on the time scale of our measurements, but the distributions do not relax sufficiently to alter our conclusions. Vibrational distributions are nascent, though vibrational relaxation of excited CO is unusually fast in the OCS bath, with rates approaching 3 percent of gas kinetic for v = 1.

Nickolaisen, Scott L.↗
NASA NTRS1996

Blowdown Wind Tunnels: Latest Citations from the Aerospace Database

The bibliography contains citations concerning the design, construction, operation, and performance of blowdown wind tunnels. The use of compressed gas, mechanical piston, or combustion exhaust to provide continuous or short-duration operation from transonic to hypersonic approach velocities is discussed. Also covered are invasive and non-invasive aerothermodynamic instrumentation, data acquisition and reduction techniques, and test reports on aerospace components. Comprehensive coverage of wind tunnel force balancing systems and supersonic wind tunnels are covered in separate bibliographies.

BIBLIOGRAPHIES↗
NASA NTRS2005

Critical Technologies for Hypersonic Vehicle Development

The objective of the present RTO/VKI Lecture Series is to focus attention on the technologies that play a critical role in hypersonic vehicle development. Owing to the demanding flight environment, successful development of hypersonic vehicles will require progress in understanding and surmounting specific technical problems in ground test, numerical simulation and flight test. Following the introductory remarks stating the objectives of the Lecture Series, a historical perspective on hypersonic vehicle development was given to establish the context and to highlight the emerging role of numerical simulation in vehicle design. A thorough review of ongoing vehicle development and flight-test programs completed the introductory portion. To provide sufficient background information, lectures were presented on compressible flows of perfect and imperfect gases, with special attention given to shock-wave boundary-layer interactions, laminar to turbulent transition, and high temperature gas properties. Advancements in computational modeling capabilities for hypersonic vehicle design were addressed, and the ongoing need for validation data, as well as a consistent validation methodology, where highlighted. Specific critical technology areas, including trajectory aerothermal environment definition, system trade studies, propulsion systems, aerodynamic control laws, flight instrumentation, thermal protection systems and flight experiments were all addressed in separate lectures given by international experts. Finally, the potential of plasma devices to ameliorate or avoid critical aerothermal phenomena was presented, providing a good example of the type of creative effort required for achieving progress. In all of the presentations the needs of future hypersonic flight vehicle development programs were addressed.

Research and Technology Organisation (RTO)↗
NASA NTRS2013

Evidence of a Discontinuous Disk Structure Around the Herbig Ae Star HD 139614

The formation and evolution of a planetary system are intrinsically linked to the evolution of the primordial accretion disk and its dust and gas content. A new class of pre-main sequence objects has been recently identified as pre-transitional disks. They present near-infrared excess coupled to a flux deficit at about 10 microns and a rising mid-infrared and far-infrared spectrum. These features suggest a disk structure with inner and outer dust components, separated by a dust-depleted region (or gap). This could be the result of particular planet formation mechanisms that occur during the disk evolution. We here report on the first interferometric observations of the disk around the Herbig Ae star HD 139614. Its infrared spectrum suggests a flared disk, and presents pre-transitional features, namely a substantial near-infrared excess accompanied by a dip around 6 microns and a rising mid-infrared part. In this framework, we performed a study of the spectral energy distribution (SED) and the mid-infrared VLTI/MIDI interferometric data to constrain the spatial structure of the inner dust disk region and assess its possibly multi-component structure. We based our work on a temperature-gradient disk model that includes dust opacity.While we could not reproduce the SED and interferometric visibilities with a one-component disk, a better agreement was obtained with a two-component disk model composed of an optically thin inner disk extending from 0.22 to 2.3 AU, a gap, and an outer temperature-gradient disk starting at 5.6 AU. Therefore, our modeling favors an extended and optically thin inner dust component and in principle rules out the possibility that the near-infrared excess originates only from a spatially confined region. Moreover, the outer disk is characterized by a very steep temperature profile and a temperature higher than 300 K at its inner edge. This suggests the existence of a warm component corresponding to a scenario where the inner edge of the outer disk is directly illuminated by the central star. This is an expected consequence of the presence of a gap, thus indicative of a "pre-transitional" structure.

primordial accretion disk↗
NASA NTRS1980

A hybrid water-splitting cycle using copper sulfate and mixed copper oxides

The Institute of Gas Technology has derived and developed a hybrid thermochemical water-splitting cycle based on mixed copper oxides and copper sulfate. Similar to other metal oxide-metal sulfate cycles that use a metal oxide to 'concentrate' electrolytically produced sulfuric acid, this cycle offers the advantage of producing oxygen (to be vented) and sulfur dioxide (to be recycled) in separate steps, thereby eliminating the need of another step to separate these gases. The conceptual process flow-sheet efficiency of the cycle promises to exceed 50%. It has been completely demonstrated in the laboratory with recycled materials. Research in the electrochemical oxidation of sulfur dioxide to produce sulfuric acid and hydrogen performed at IGT indicates that the cell performance goals of 200 mA/sq cm at 0.5 V will be attainable using relatively inexpensive electrode materials.

Schreiber, J. D.↗