SEARCH · Engineering Papers

Results for “Flow Conditions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74

All sources NASA NTRS DOE OSTI

NASA NTRS1977

Combustion of liquid sprays at high pressures

The combustion of pressure atomized fuel sprays in high pressure stagnant air was studied. Measurements were made of flame and spray boundaries at pressures in the range 0.1-9 MPa for methanol and n-pentane. At the higher test pressure levels, critical phenomena are important. The experiments are compared with theoretical predictions based on a locally homogeneous two-phase flow model. The theory correctly predicted the trends of the data, but underestimates flame and spray boundaries by 30-50 percent, indicating that slip is still important for the present experiments (Sauter mean diameters of 30 microns at atmospheric pressure under cold flow conditions). Since the sprays are shorter at high pressures, slip effects are still important even though the density ratio of the phases approach one another as the droplets heat up. The model indicates the presence of a region where condensed water is present within the spray and provides a convenient means of treating supercritical phenomena.

Shearer, A. J.↗

NASA NTRS1977

Load distribution on a closed-coupled wing canard at transonic speeds

A wind tunnel test where load distributions were obtained at transonic speeds on both the canard and wing surfaces of a closely coupled wing canard configuration is reported. Detailed component and configuration arrangement studies to provide insight into the various aerodynamic interference effects for the leading edge vortex flow conditions encountered are included. Data indicate that increasing the Mach number from 0.70 to 0.95 caused the wing leading edge vortex to burst over the wing when the wing was in the presence of the high canard.

Gloss, B. B.↗

NASA NTRS1977

Flow characteristics in an expansion tunnel as inferred from velocity measurements

A photoionization technique was used to study flow characteristics in an expansion tunnel. Vertical surveys of the axial component of flow velocity just downstream from the nozzle exit were obtained, and estimates of freestream density were inferred from the velocity measurement technique. The pitot pressure was measured and compared to the average axial component of velocity as a function of time for the two cases when air and CO2 were used as test gases. Vertical velocity and static density profiles at the nozzle exit are presented for the case when CO2 was used as test gas. Experimental results were used to determine the diameter and uniformity of the test core at the nozzle exit and the duration of the quasi-steady flow period. These data are relevant to evaluation of the suitability of operating an expansion tube as an expansion tunnel. The expansion tunnel is an expansion tube with a conical nozzle positioned at the exit of the acceleration section, so that nozzle entrance flow conditions are hypersonic and characterized by hypervelocity.

Miller, C. G.↗

NASA NTRS1977

Effect of coolant flow ejection on aerodynamic performance of low-aspect-ratio vanes. 2: Performance with coolant flow ejection at temperature ratios up to 2

The aerodynamic performance of a 0.5 aspect ratio turbine vane configuration with coolant flow ejection was experimentally determined in a full annular cascade. The vanes were tested at a nominal mean section ideal critical velocity ratio of 0.890 over a range of primary to coolant total temperature ratio from 1.0 to 2.08 and a range of coolant to primary total pressure ratio from 1.0 to 1.4 which corresponded to coolant flows from 3.0 to 10.7 percent of the primary flow. The variations in primary and thermodynamic efficiency and exit flow conditions with circumferential and radial position were obtained.

Hass, J. E.↗

NASA NTRS1977

Calibration of transonic and supersonic wind tunnels

State-of-the art instrumentation and procedures for calibrating transonic (0.6 less than M less than 1.4) and supersonic (M less than or equal to 3.5) wind tunnels were reviewed and evaluated. Major emphasis was given to transonic tunnels. Continuous, blowdown and intermittent tunnels were considered. The required measurements of pressure, temperature, flow angularity, noise and humidity were discussed, and the effects of measurement uncertainties were summarized. A comprehensive review of instrumentation currently used to calibrate empty tunnel flow conditions was included. The recent results of relevant research are noted and recommendations for achieving improved data accuracy are made where appropriate. It is concluded, for general testing purposes, that satisfactory calibration measurements can be achieved in both transonic and supersonic tunnels. The goal of calibrating transonic tunnels to within 0.001 in centerline Mach number appears to be feasible with existing instrumentation, provided correct calibration procedures are carefully followed. A comparable accuracy can be achieved off-centerline with carefully designed, conventional probes, except near Mach 1. In the range 0.95 less than M less than 1.05, the laser Doppler velocimeter appears to offer the most promise for improved calibration accuracy off-centerline.

Reed, T. D.↗

NASA NTRS1978

Theoretical analysis of aerodynamic characteristics of two helicopter rotor airfoils

An analytical study was conducted to predict the aerodynamic characteristics of two helicopter rotor airfoils. Documentation of the predictive process covers the development of empirical factors used in conjunction with computer programs for airfoil analysis. Tables of lift, drag, and pitching-moment coefficient for each airfoil were prepared for two dimensional, steady flow conditions at Mach numbers from 0.3 to 0.9 and Reynolds numbers of 7,700,000 to 23,000,000, respectively.

Morris, C. E. K., Jr.↗

NASA NTRS1978

Development of advanced stability theory suction prediction techniques for laminar flow control

The problem of obtaining accurate estimates of suction requirements on swept laminar flow control wings was discussed. A fast accurate computer code developed to predict suction requirements by integrating disturbance amplification rates was described. Assumptions and approximations used in the present computer code are examined in light of flow conditions on the swept wing which may limit their validity.

Srokowski, A. J.↗

NASA NTRS1978

Acoustic tests of duct-burning turbofan jet noise simulation

The results of a static acoustic and aerodynamic performance, model-scale test program on coannular unsuppressed and multielement fan suppressed nozzle configurations are summarized. The results of the static acoustic tests show a very beneficial interaction effect. When the measured noise levels were compared with the predicted noise levels of two independent but equivalent conical nozzle flow streams, noise reductions for the unsuppressed coannular nozzles were of the order of 10 PNdB; high levels of suppression (8 PNdB) were still maintained even when only a small amount of core stream flow was used. The multielement fan suppressed coannular nozzle tests showed 15 PNdB noise reductions and up to 18 PNdB noise reductions when a treated ejector was added. The static aerodynamic performance tests showed that the unsuppressed coannular plug nozzles obtained gross thrust coefficients of 0.972, with 1.2 to 1.7 percent lower levels for the multielement fan-suppressed coannular flow nozzles. For the first time anywhere, laser velocimeter velocity profile measurements were made on these types of nozzle configurations and with supersonic heated flow conditions. Measurements showed that a very rapid decay in the mean velocity occurs for the nozzle tested.

Knott, P. R.↗

NASA NTRS1978

Transonic wing analysis using advanced computational methods

This paper discusses the application of three-dimensional computational transonic flow methods to several different types of transport wing designs. The purpose of these applications is to evaluate the basic accuracy and limitations associated with such numerical methods. The use of such computational methods for practical engineering problems can only be justified after favorable evaluations are completed. The paper summarizes a study of both the small-disturbance and the full potential technique for computing three-dimensional transonic flows. Computed three-dimensional results are compared to both experimental measurements and theoretical results. Comparisons are made not only of pressure distributions but also of lift and drag forces. Transonic drag rise characteristics are compared. Three-dimensional pressure distributions and aerodynamic forces, computed from the full potential solution, compare reasonably well with experimental results for a wide range of configurations and flow conditions.

Henne, P. A.↗

NASA NTRS1978

Subsonic vortex-flow design study for slender wings

A theoretical study describing the effects of spanwise camber on the lift dependent drag of slender delta wings having leading-edge-vortex-flow is presented. The earlier work by Barsby, using conical flow, indicated that drag levels similar to those in attached flow could be obtained. This is reexamined and then extended to the more practical case of nonconical flow by application of the vortex-lattice method coupled with the suction-analogy and the recently developed Boeing free-vortex-sheet method. Lastly, a design code is introduced which employs the suction analogy in an attempt to define 'optimum' camber surfaces for minimum lift dependent drag for vortex flow conditions

Lamar, J. E.↗

NASA NTRS1978

An experimental map of the internal structure of a vortex breakdown

The flow field of an 'axisymmetric' vortex breakdown has been mapped using a laser-Doppler anemometer. The interior of the recirculation zone is dominated by energetic, non-axisymmetric, low frequency periodic fluctuations. Spectra for a number of points inside this zone, as well as time-averaged swirl and axial velocity profiles both inside and outside the recirculation zone, have been obtained. The time-averaged streamlines in the interior show an unexpected two-celled structure attributed to the action of the fluctuations. Although the present experiment deals with one particular breakdown, flow-visualization studies indicate that the case examined is typical of the 'axisymmetric' form of breakdown over a range of flow conditions.

Faler, J. H.↗

NASA NTRS1978

The impact of turbulence on a radiating shock layer with coupled ablation injection

This paper provides a description of the potential impact of turbulence on a radiating flow field with large surface blowing. This is accomplished by calculating the forebody flow field with coupled carbon-phenolic mass injection for a probe entering the Jupiter atmosphere. Both laminar and turbulent flow conditions are assumed. For the no blowing solutions, turbulence is shown to have no impact on the surface radiative heating. However, with ablation injection, turbulence significantly increases the surface radiative heating rate. This occurs because the turbulence brings the high temperature gases closer to the surface, thus thinning the cool molecular gases at the wall which are responsible for blocking much of the radiation.

Moss, J. N.↗

NASA NTRS1978

Research study: Thermal curtain permeability and thermal response test for SRB reentry

Nine inch diameter samples of the material which will provide thermal and acoustic protection between the nozzle and outer skirt on the space shuttle solid rocket boosters were subjected to heating tests to determine the porosity of the material and the thermal response to a step change in heating. For the porosity measurements a steady state flow of air at 70 F, 500 F, and 1000 F was passed through a sample of the curtain material and measurements of the flow rates were made at different pressure drops across the sample. For the transient measurements, a sample of the curtain material was subjected to a step change in temperature as air was passed through the sample. Measurements of the heat flow through the sample were made as a function of time after the input of the heat pulse. The sample consisted of three layers of curtain panels. Each panel was made of combinations of quartz and fiberglass cloth between which a fiberfrax filler material had been stitched. The hardware design and test procedures were described. Data are provided in engineering units for the flow conditions and and temperatures at which measurements were conducted.

Fuller, C. E.↗

NASA NTRS1978

Description and preliminary calibration results for the Langley hypersonic CF4 tunnel

A detailed description of the hypersonic CF4 tunnel is presented along with discussion of the basic components, instrumentation, and operating procedure. Operational experience with the CF4 reclaimer and lead-bath heater is discussed. Comparison of measured and predicted shock detachment distance on a sphere and pressure distributions measured on a sharp leading-edge flat plate revealed the absence of significant flow nonuniformity and lent creditability to predicted free stream flow conditions. The economic operation of this facility centers about the CF4 reclaimer, which was designed to operate at an efficiency of 90 to 95 percent. A number of modifications were made to the reclaimer system to improve its performance, and presently, the system reclaims approximately 75 percent of the test gas. Even with current budgetary constraints, this efficiency permits the CF4 tunnel to be operated as a viable research wind tunnel.

Midden, R. E.↗

NASA NTRS1978

Low cost silicon solar array project: Feasibility of low-cost, high-volume production of silane and pyrolysis of silane to semiconductor-grade silicon

Silicon epitaxy analysis of silane produced in the Process Development Unit operating in a completely integrated mode consuming only hydrogen and metallurgical silicon resulted in film resistivities of up to 120 ohms cm N type. Preliminary kinetic studies of dichlorosilane disproportionation in the liquid phase have shown that 11.59% SiH4 is formed at equilibrium after 12 minutes contact time at 56 C. The fluid-bed reactor was operated continuously for 48 hours with a mixture of one percent silane in helium as the fluidizing gas. A high silane pyrolysis efficiency was obtained without the generation of excessive fines. Gas flow conditions near the base of the reactor were unfavorable for maintaining a bubbling bed with good heat transfer characteristics. Consequently, a porous agglomerate formed in the lower portion of the reactor. Dense coherent plating was obtained on the silicon seed particles which had remained fluidizied throughout the experiment.

Breneman, W. C.↗

NASA NTRS1979

Experimental studies on the effects of a sting support on the pressure distribution around a spherical object

Experiments were conducted on a spherical object, 2.5 inches in diameter, to obtain the pressure distribution around its meridan plane. In most of the tests the sphere was provided with a tail consisting of a circular cylinder that was attached directly to the rear with its axis in alignment with the center of the sphere. In some tests the tail was removed and the sphere alone was tested for comparison purposes. The main object of the tests was to obtain information on tail interference with the pressure distribution. The results of the tests show that the pressure distribution was affected by the presence of the tail to a minor extent only, while major differences occurred with the variation of the Reynolds number. The experiments were performed both in an open as well as inside a closed wind tunnel under steady flow conditions at Reynolds numbers ranging from 0.91 to 2.6 x 100000.

Barna, P. S.↗

NASA NTRS1979

Low speed airfoil design and analysis

A low speed airfoil design and analysis program was developed which contains several unique features. In the design mode, the velocity distribution is not specified for one but many different angles of attack. Several iteration options are included which allow the trailing edge angle to be specified while other parameters are iterated. For airfoil analysis, a panel method is available which uses third-order panels having parabolic vorticity distributions. The flow condition is satisfied at the end points of the panels. Both sharp and blunt trailing edges can be analyzed. The integral boundary layer method with its laminar separation bubble analog, empirical transition criterion, and precise turbulent boundary layer equations compares very favorably with other methods, both integral and finite difference. Comparisons with experiment for several airfoils over a very wide Reynolds number range are discussed. Applications to high lift airfoil design are also demonstrated.

Eppler, R.↗

NASA NTRS1979

Inverse boundary-layer technique for airfoil design

A description is presented of a technique for the optimization of airfoil pressure distributions using an interactive inverse boundary-layer program. This program allows the user to determine quickly a near-optimum subsonic pressure distribution which meets his requirements for lift, drag, and pitching moment at the desired flow conditions. The method employs an inverse turbulent boundary-layer scheme for definition of the turbulent recovery portion of the pressure distribution. Two levels of pressure-distribution architecture are used - a simple roof top for preliminary studies and a more complex four-region architecture for a more refined design. A technique is employed to avoid the specification of pressure distributions which result in unrealistic airfoils, that is, those with negative thickness. The program allows rapid evaluation of a designed pressure distribution off-design in Reynolds number, transition location, and angle of attack, and will compute an airfoil contour for the designed pressure distribution using linear theory.

Henderson, M. L.↗