Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dislocation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74

Coalescence of GaP on V-Groove Si

In recent years, better understanding and control over the formation of crystalline defects during the direct epitaxy of III-V semiconductors on Si substrates via metal organic vapor phase epitaxy (MOVPE) has enabled large gains in III-V-on-Si solar cell efficiency, pointing to pathway to lower-cost, high-performance III-V solar cells. However, such results have only been achieved on costly chemo-mechanically-polished (CMP) Si wafers. The use of V-groove nanopatterned Si substrates has demonstrated similarly high-crystalline-quality III-V-on-Si epitaxy, but also can be combined with lower-cost polishing techniques. Although they offer a potential cost advantage, growth on V-groove substrates adds challenges not present for epitaxy on planar wafers (the III-V material must be coalesced into a thin film after an initial nucleation stage). MOVPE growth conditions that promote highly facet-selective lateral growth needed for coalescence are generally actively avoided for conventional thin fim growth, so growth conditions need to be re-developed for V-groove-based epitaxy. Additionally, coalescence add complexity to the dislocation dynamics related to lattice relaxation, so strategies used to keep threading dislocation density (TDD) low on planar substrates need to be re-tuned for V-grooves. We have studied the morphological evolution and dislocation dynamics of GaP grown on V-groove Si by MOVPE. Growth conditions of V/III=5,000 and Tg=800 degrees C were uniquely found to produce extremely smooth coalesced thin films, with an RMS roughness of 0.2 nm measured by AFM. Additionally, at this growth condition, we identified two regimes of growth determined by the width of the SiNx cap (a remnant of the nanopatterning process) at the top of the V-grooves. For narrow caps, the GaP coalesces into a thin film, and for wide caps, the GaP evolves into {1 1 1}-faceted diamonds that do not coalesce. We suggest the influence of Si from the sidewalls of the V-grooves on the surface reconstruction of the GaP as the mechanism for this effect, with reflection difference spectroscopy (RDS) and Si doping experiments supporting this theory. In addition to morphology, the dislocation dynamics of the system were studied with electron channeling contrast imaging (ECCI) and transmission electron microscopy (TEM). The TDD of the coalesced GaP films was found to be 5 x 10^7 cm^-2 after coalescence via ECCI, a level still too high for high-quality solar cells. However, misfit dislocations crossing multiple grooves greater than 20 micrometers long were observed in ECCI, suggesting that the V-grooves do not block dislocation glide. TEM prior to and after coalescence was used to distinguish between dislocation creation driven by growth conditions and coalescence. Finally, strategies to reduce the dislocation density to levels acceptable for solar cells will be discussed.

GaP↗

Defect Generation and Propagation in MC-Si Ingots: Influence on Cell-to-Cell Performance Variation

This paper describes results of our study aimed at understanding mechanism(s) of dislocation generation and propagation in multicrystalline silicon (mc-Si) ingots, and evaluating their influence on the solar cell performance. This work was done in two parts: (i) Measurement of dislocation distributions along various bricks, selected from strategic locations within several ingots; and (ii) Theoretical modeling of the cell performance corresponding to the measured dislocation distributions. Solar cells were fabricated on wafers of known dislocation distribution, and the results were compared with the theory. These results show that cell performance can be accurately predicted from the dislocation distribution, and the changes in the dislocation distribution are the primary cause for variations in the cell-to-cell performance. The dislocation generation and propagation mechanisms, suggested by our results, are described in this paper.

14 SOLAR ENERGY↗

Prismatic-to-basal plastic slip transition in zirconium

Here, we model three-dimensional dislocation ensembles in Zr pillars using newly developed mobility laws for dislocations on prismatic and basal planes. The effects of the loading orientation and temperature on the micro-scale mechanical response of single crystals are systematically explored. Easy dislocation glide is observed on prismatic planes, while hard glide occurs on basal planes. By selection of sample temperature and loading orientation, we show that the transition from prismatic to basal glide of dislocation ensembles can be controlled. We also show that the presence of dislocation cross-slip strongly promotes prismatic glide as a result of prismatic/basal cross-slip energy asymmetry. Cross-slip does not alter the occurrence of plastic slip transition but only induces a shift towards higher temperatures. The preponderance of plastic slip on basal or prismatic planes is found to be mediated by a transitional dislocation, which is composed of glissile segments on parallel prismatic planes connected by glissile super-jogs on basal planes. These findings provide a mechanistic understanding of experiments and highlight the significance of transitional prismatic-basal dislocations on the macroscopic characteristics of plasticity in HCP crystals.

36 MATERIALS SCIENCE↗

Reversing inverse Hall-Petch and direct computation of Hall-Petch coefficients

A 2D bicrystal atomistic model of dislocation transmission through a Σ11<101>{131} symmetric-tilt grain boundary reveals details of Hall-Petch breakdown in the single dislocation regime in Al, Ni, and Cu. Partly based on a previous study, this research determines the stress required for a single dislocation to be transmitted through the Σ11 boundary and finds that single dislocation transmission typically deviates from Hall-Petch behavior because the leading partial dislocation becomes trapped in the boundary and emits glissile grain boundary disconnections that cause boundary sliding deformation at stresses well below boundary transmission stresses. Thus, mechanisms of inverse Hall-Petch, namely grain boundary shear and sliding, are shown to operate in lieu of grain boundary transmission in the single dislocation regime. However, by controlling the applied stresses, inverse Hall-Petch can be reversed and typical Hall- Petch grain boundary transmission regained. This, in turn, allows the direct computation of Hall-Petch coefficients. Further, a second dislocation on the same slip plane preserves typical Hall-Petch behavior for Al and Ni and does not lead to boundary sliding events, thus implying a critical grain size for Hall-Petch breakdown based on the pileup model.

36 MATERIALS SCIENCE↗

Phase-field modeling of radiation-induced composition redistribution: An application to additively manufactured austenitic Fe–Cr–Ni

Multicomponent alloys undergoing irradiation damage develop radiation-induced composition redistribution at point defect sinks such as grain boundaries (GBs) and dislocations. Such redistribution results in undesired changes to their mechanical behavior and corrosion resistance. Additively manufactured alloys proposed for future nuclear applications are expected to demonstrate a distinct response to irradiation owing to their unique microstructure with as-solidified dislocation density and chemical microsegregation. To capture the composition redistribution in such systems, we develop a mesoscale model with coupled evolution of atomic and point defect components in the presence of dislocation density, dislocation heterogeneity, and thermodynamic interactions at the GB. The model is parameterized for an FCC Fe–Cr–Ni alloy as a representative system for austenitic stainless steels, and simulations are performed in 1D and 2D as a function of irradiation temperature, dose, dislocation density, and grain size. Radiation-induced segregation (RIS) characterized by Cr depletion and Ni enrichment is predicted at both the GB and the dislocation cell wall, with RIS being lower in magnitude but wider at the cell wall. Strongly biased absorption of self-interstitials by dislocations is found to suppress Ni enrichment but slightly enhance Cr depletion under certain conditions. Thermodynamic segregation at the GB is predicted to be narrower and opposite in sign to RIS for both Cr and Ni. Importantly, non-monotonic segregation is found to occur when both thermodynamic and RIS mechanisms are considered, providing a novel physical interpretation of experimental observations. The model is expected to serve as a key tool in accelerated qualification of irradiated materials.

additively manufactured microstructure↗

Characterizing the nano-structure and defect structure of nano-scaled non-ferrous structural alloys

The presence and interaction of nanotwins, geometrically necessary dislocations, and grain boundaries play a key role in the mechanical properties of nanostructured crystalline materials. Therefore, it is vital to determine the orientation, width and distance of nanotwins, the angle and axis of grain boundary misorientations as well as the type and the distributions of dislocations in an automatic and statistically meaningful fashion in a relatively large area. In this paper, such details are provided using a transmission electron microscope-based orientation microscopy technique called ASTAR™/precession electron diffraction. The remarkable spatial resolution of this technique (~ 2 nm) enables highly detailed characterization of nanotwins, grain boundaries and the configuration of dislocations. This orientation microscopy technique provides the raw data required for the determination of these parameters. The procedures to post-process the ASTAR™/PED datasets in order to obtain the important (and currently largely hidden) details of nanotwins as well as quantifications of dislocation density distributions are described in this study. - Highlights: • EBSD cannot characterize defects such as dislocations, grain boundaries and nanotwins in severely deformed metals. • TEM based orientation microscopy technique called ASTAR™/PED was used to resolve the problem. • Locations and orientations of nanotwins, dislocation density distribution and grain boundary characters can be resolved. • This work provides the bases for further studies on the interactions between dislocations, grain boundaries and nanotwins. • The computation part is explained sufficiently which helps the readers to post process their own data.

36 MATERIALS SCIENCE↗

Extended defects in GaAs/GaAs 1-x Sb x /GaAs (001) heterostructures

The atomic-scale structure of extended defects in GaAs/GaAs 1-x Sb x /GaAs (001) heterostructures has been characterized using aberration-corrected scanning transmission electron microscopy. The defect located at the tensile-strained GaAs(cap)/GaAs 0.34 Sb 0.66 interface had no edge component in the projection plane and is identified as either a dissociated screw dislocation or a partial dislocation dipole. The associated intrinsic stacking fault is bounded by two 30° Shockley partial dislocations of opposite sign. Another defect, located at the compressively-strained GaAs 0.91 Sb 0.09 /GaAs(substrate) interface, is identified as a dissociated 90° dislocation. The associated intrinsic stacking fault is bounded by a 30° Shockley partial dislocation and a partial dislocation with a Burgers vector of either or , where a is the lattice constant. Unpaired atomic columns observed at the cores of the 30° Shockley partial dislocations indicate that both defects belong primarily to the glide set.

36 MATERIALS SCIENCE↗

Anomalous thermal transport in Eshelby twisted van der Waals nanowires

Dislocations in van der Waals (vdW) layered nanomaterials induce strain and structural changes that substantially impact thermal transport. Understanding these effects could enable the manipulation of dislocations for improved thermoelectric and optoelectronic applications, but experimental insights remain limited. Here, in this study, we use synthetic Eshelby twisted vdW GeS nanowires (NWs) with single screw dislocations as a model system to explore the interplay between dislocation-induced structural modifications and lattice thermal conductivity. Our measurements reveal a monoclinic structure stabilized by the dislocation, leading to a substantial drop in thermal conductivity for larger-diameter NWs (70% at room temperature), supported by first-principles calculations. Interestingly, we also find an anomalous enhancement of thermal conductivity with decreasing diameter in twisted NWs, contrary to typical trends in non-twisted GeS NWs. This is attributed to increased conductivity near the NW cores due to compressive strain around the central dislocations, and aligns with a density-functional-theory-informed core–shell model. Our results highlight the critical role of dislocations in thermal conduction, providing fundamental insights for defect and strain engineering in advanced thermal applications.

36 MATERIALS SCIENCE↗

Defect reduction in Si-doped Al{sub 0.45}Ga{sub 0.55}N films by SiN{sub x} interlayer method

The dislocation density in AlGaN epitaxial layers with Al content as high as 45% grown on sapphire substrates has been effectively reduced by introducing an in-situ deposited SiN{sub x} nanomask layer in this study. By closely monitoring the evolution of numerous material properties, such as surface morphology, dislocation density, photoluminescence, strain states, and electron mobility of the Si-Al{sub 0.45}Ga{sub 0.55}N layers as the functions of SiN{sub x} interlayer growth time, the surface coverage fraction of SiN{sub x} is found to be a crucial factor determining the strain states and dislocation density. The dependence of the strain states and the dislocation density on the surface coverage fraction of SiN{sub x} nanomask supports the very different growth models of Al-rich AlGaN on SiN{sub x} interlayer due to the reduced nucleation selectivity compared with the GaN counterpart. Compared with GaN, which can only nucleate at open pores of SiN{sub x} nanomask, Al-rich AlGaN can simultaneously nucleate at both open pores and SiN{sub x} covered areas. Dislocations will annihilate at the openings due to the 3D growth initiated on the opening area, while 2D growth mode is preserved on SiN{sub x} and the threading dislocations are also preserved. During the following growth process, lateral overgrowth will proceed from the Al{sub 0.45}Ga{sub 0.55}N islands on the openings towards the regions covered by SiN{sub x}, relaxing the compressive strain and bending the dislocations at the same time.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Atomistic tensile deformation mechanisms of Fe with gradient nano-grained structure

Large-scale molecular dynamics (MD) simulations have been performed to investigate the tensile properties and the related atomistic deformation mechanisms of the gradient nano-grained (GNG) structure of bcc Fe (gradient grains with d from 25 nm to 105 nm), and comparisons were made with the uniform nano-grained (NG) structure of bcc Fe (grains with d = 25 nm). The grain size gradient in the nano-scale converts the applied uniaxial stress to multi-axial stresses and promotes the dislocation behaviors in the GNG structure, which results in extra hardening and flow strength. Thus, the GNG structure shows slightly higher flow stress at the early plastic deformation stage when compared to the uniform NG structure (even with smaller grain size). In the GNG structure, the dominant deformation mechanisms are closely related to the grain sizes. For grains with d = 25 nm, the deformation mechanisms are dominated by GB migration, grain rotation and grain coalescence although a few dislocations are observed. For grains with d = 54 nm, dislocation nucleation, propagation and formation of dislocation wall near GBs are observed. Moreover, formation of dislocation wall and dislocation pile-up near GBs are observed for grains with d = 105 nm, which is the first observation by MD simulations to our best knowledge. The strain compatibility among different layers with various grain sizes in the GNG structure should promote the dislocation behaviors and the flow stress of the whole structure, and the present results should provide insights to design the microstructures for developing strong-and-ductile metals.

36 MATERIALS SCIENCE↗

Structure of self-interstitial atom clusters in iron and copper

The dislocation core structure of self-interstitial atom (SIA) clusters in bcc iron and fcc copper is determined using the hybrid ab initio continuum method of Banerjee et al. [Philos. Mag. 87, 4131 (2007)]. To reduce reliance on empirical potentials and to facilitate predictions of the effects of local chemistry and stress on the structure of defects, we present here a hybrid extension of the Peierls-Nabarro continuum model, with lattice resistance to slip determined separately from ab initio calculations. A method is developed to reconstruct atomic arrangements and geometry of SIA clusters from the hybrid model. The results are shown to compare well with molecular-dynamics simulations. In iron, the core structure does not show dependence on the size of the self-interstitial cluster, and is nearly identical to that of a straight edge dislocation. However, the core structure of SIA clusters in Cu is shown to depend strongly on the cluster size. Small SIA clusters are found to have nondissociated compact dislocation cores, with a strong merging of Shockley partial dislocations and a relatively narrow stacking fault (SF) region. The compact nature of the SIA core in copper is attributed to the strong dependence of the self-energy on the cluster size. As the number of atoms in the SIA cluster increases, Shockley partial dislocations separate and the SF region widens, rendering the SIA core structure to that of an edge dislocation. The separation distance between the two partials widens as the cluster size increases, and tends to the value of a straight edge dislocation for cluster sizes above 400 atoms. The local stress is found to have a significant effect on the atomic arrangements within SIA clusters in copper and the width of the stacking faults. An applied external shear can delocalize the core of an SIA cluster in copper, with positive shear defined to be on the (111) plane along the [112] direction. For an SIA cluster containing 1600 atoms, a positive 1 GPa shear stress delocalizes the cluster and expands the SF to 30b, while a negative shear stress of 2 GPa contracts the core to less than 5b, where b is the Burgers vector magnitude.

36 MATERIALS SCIENCE↗

Deformed Materials: Towards a Theory of Materials Morphology Dynamics

This grant supported work on the response of crystals to external stress. Our primary work described how disordered structural materials break in two (statistical models of fracture in disordered materials), studied models of deformation bursts (avalanches) that mediate deformation on the microscale, and developed continuum dislocation dynamics models for plastic deformation (as when scooping ice cream bends a spoon, Fig. 9). Glass is brittle -- it breaks with almost atomically smooth fracture surfaces. Many metals are ductile -- when they break, the fracture surface is locally sheared and stretched, and it is this damage that makes them hard to break. Bone and seashells are made of brittle material, but they are strong because they are disordered -- lots of little cracks form as they are sheared and near the fracture surface, diluting the external force. We have studied materials like bone and seashells using simulations, mathematical tools, and statistical mechanics models from physics. In particular, we studied the extreme values of fracture strengths (how likely will a beam in a bridge break far below its design strength), and found that the traditional engineering tools could be improved greatly. We also studied fascinating crackling-noise precursors -- systems which formed microcracks of a broad range of sizes before they broke. Ductile metals under stress undergo irreversible plastic deformation -- the planes of atoms must slide across one another (through the motion of dislocations) to change the overall shape in response to the external force. Microscopically, the dislocations in crystals move in bursts of a broad range of sizes (termed 'avalanches' in the statistical mechanics community, whose motion is deemed 'crackling noise'). In this grant period, we resolved a longstanding mystery about the average shape of avalanches of fixed duration (using tools related to an emergent scale invariance), we developed the fundamental theory describing the shapes of avalanches and how they are affected by the edges of the microscope viewing window, we found that slow creep of dislocations can trigger an oscillating response explaining recent experiments, we explained avalanches under external voltage, and we have studied how avalanches in experiments on the microscale relate to deformation of large samples. Inside the crystals forming the metal, the dislocations arrange into mysterious cellular structures, usually ignored in theories of plasticity. Writing a natural continuum theory for dislocation dynamics, we found that it spontaneously formed walls -- much like models of traffic jams and sonic booms. These walls formed rather realistic cellular structures, which we examined in great detail -- our walls formed fractal structures with fascinating scaling properties, related to those found in turbulent fluids. We found, however, that the numerical and mathematical tools available to solve our equations were not flexible enough to incorporate materials-specific information, and our models did not show the dislocation avalanches seen experimentally. In the last year of this grant, we wrote an invited review article, explaining how plastic flow in metals shares features with other stressed materials, and how tools of statistical physics used in these other systems might be crucial for understanding plasticity.

36 MATERIALS SCIENCE↗

Correlation Between Irradiation Defects and Transition Dimension for TEM In Situ Mechanical Testing

The objective of this study is to establish a relationship between specimen size effect transition dimension and defect number density. Transmission electron microscopic (TEM) in situ mechanical testing enables one to directly observe fundamental plastic phenomena simultaneous to quantitative measurement of applied load and displacement, in specimens having dimensions on the order of nanometers to micrometers. Thus, these techniques hold great promise for enhancing our scientific understanding of deformation mechanisms in volume-limited materials, such as shallow ion irradiated layers. The 'specimen size effect' is a major detractor, however, of any miniaturized mechanical testing technique. This effect is the direct result of low-volume specimens containing too few dislocations, such that plasticity is governed by the stress required to introduce more dislocations to the specimen. The consequence is an inflated yield stress measurement relative to the 'bulk' yield stress. As the specimen size increases, so too does the number of dislocations present, and plasticity becomes controlled by the stress needed to move these dislocations. Yield stress measurements decrease to their bulk values. The minimum specimen dimension for which plastic yield is controlled by dislocation motion rather than dislocation introduction, is what we herein refer to as the 'transition dimension'. However, the overall yield stress is governed by the superposition of dislocations, grain boundaries, and dispersed obstacles of varying morphologies. It is theorized that the higher the number density of these dispersed obstacles, the lower the transition dimension. Since it is well known that irradiation introduces a high density of defects, we hypothesize that the transition dimension is sufficiently low in irradiated materials so as to enable meaningful quantitative values of yield stress through TEM in situ mechanical tests.

36 MATERIALS SCIENCE↗

Revisiting the Al/Al 2 O 3 Interface: Coherent Interfaces and Misfit Accommodation

We report the coherent and semi-coherent Al/α-Al 2 O 3 interfaces using molecular dynamics simulations with a mixed, metallic-ionic atomistic model. For the coherent interfaces, both Al-terminated and O-terminated nonstoichiometric interfaces have been studied and their relative stability has been established. To understand the misfit accommodation at the semi-coherent interface, a 1-dimensional (1D) misfit dislocation model and a 2-dimensional (2D) dislocation network model have been studied. For the latter case, our analysis reveals an interface dislocation structure with a network of three sets of parallel dislocations, each with pure-edge character, giving rise to a pattern of coherent and stacking-fault-like regions at the interface. Structural relaxation at elevated temperatures leads to a further change of the dislocation pattern, which can be understood in terms of a competition between the stacking fault energy and the dislocation interaction energy at the interface. In conclusion, our results are expected to serve as an input for the subsequent dislocation dynamics models to understand and predict the macroscopic mechanical behavior of Al/α-Al 2 O 3 composite heterostructures.

36 MATERIALS SCIENCE↗

Multiscale Modeling of Inclusions and Precipitation Hardening in Metal Matrix Composites: Application to Advanced High-Strength Steels

In this study, the strengthening effect of inclusions and precipitates in metals is investigated within a multiscale approach that utilizes models at various length scales, namely, Molecular Mechanics (MM), discrete Dislocation Dynamics (DD), and an Eigenstrain Inclusion Method (EIM). Particularly, precipitates are modeled as hardsoft particles whose stress fields interact with dislocations. The stress field resulting from the elastic mismatch between the particles and the matrix is accounted for through the EIM. While the MM method is employed for the purpose of developing rules for DD for short range interaction between a single dislocation and an inclusion, the DD method is used to predict the strength of the composite resulting from the interaction between ensembles of dislocations and particles. As an application to this method, the mechanical behavior of Advanced High Strength Steel (AHSS) is investigated and the results are then compared to the experimental data. The results show that the finely dispersive precipitates can strengthen the material by pinning the dislocations up to a certain shear stress and retarding the recovery, as well as annihilation of dislocations. The DD results show that strengthening due to nano sized particles is a function of the density and size of the precipitates. This size effect is then explained using a mechanistic model developed based on dislocation-particle interaction.

Environmental Molecular Sciences Laboratory↗

Sculpting crystals one Burgers vector at a time: Toward colloidal lattice robot swarms

Plastic deformation of crystalline materials with isotropic particle attractions proceeds by the creation and migration of dislocations under the influence of external forces. If dislocations are produced and migrated under the action of local forces, then material shape change can occur without the application of surface forces. We investigate how particles with variable diameters can be embedded in colloidal monolayers to produce dislocations on demand. Additionally, we find in simulation that when embedded clusters of variable diameter particles are taken through multiple cycles of swelling and shrinking, large cumulative plastic slip is produced by the creation and biased motion of dislocation pairs in the solid for embedded clusters of particular geometries. In this way, dislocations emitted by these clusters (biased “dislocation emitters”) can be used to reshape colloidal matter. Our results are also applicable to larger-scale swarms of robotic particles that organize into dense ordered two-dimensional (2D) arrangements. We conclude with a discussion of how dislocations fulfill for colloids the role sought by “metamodules” in lattice robotics research and show how successive applications of shear as a unit operation can produce shape change through slicing and swirling.

36 MATERIALS SCIENCE↗