Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Alternating minimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Investigation of long-term light stability of negative charge injected into oxide-nitride-oxide passivation stack of crystalline silicon solar cells

A negatively charged oxide-nitride-oxide stack for field-effect passivation of crystalline silicon solar cells is discussed. The negative charge was injected into the stack by a plasma charge injection technology. Charge stability was studied by exposing samples to AM1.5 simulation visible light and full-spectrum light at temperatures ranging from 55 to 78 °C for up to 300 h. Charge injection and loss were quantified based on shifts in the flatband voltage of capacitance–voltage curves measured with a mercury probe. The most probable mechanism of charge loss was found to be diffusion of negative charged hydrogen atoms through nitride and bottom oxide. The optimum recipe for each layer of the stack was investigated to minimize the loss of injected charge. The flatband voltage decay of the optimized stack was found to fit a power-law trend, suggesting the dispersive transport of hydrogen atoms with a dispersion parameter of ~0.06–0.07. The optimized stack is projected to maintain a negative charge density of about 3.6 × 10 12 cm –2 or more after 25 years of field operation in an environment such as Arizona, which would be sufficient for field-effect passivation under one-sun illumination. Furthermore, the high stability of the negative injected charge makes the plasma charging technology a safer and lower cost alternative to Al 2 O 3 -passivation technology commonly used to passivate p-type surfaces.

14 SOLAR ENERGY↗
DOE OSTI2014

Reconciling disparate views of template-directed nucleation through measurement of calcite nucleation kinetics and binding energies

The physical basis for how macromolecules regulate the onset of mineral formation in calcifying tissues is not well established. A popular conceptual model assumes the organic matrix provides a stereochemical match during cooperative organization of solute ions. In contrast, another uses simple binding assays to identify good promoters of nucleation. Here, we reconcile these two views and provide a mechanistic explanation for template-directed nucleation by correlating heterogeneous nucleation barriers with crystal–substrate-binding free energies. We first measure the kinetics of calcite nucleation onto model substrates that present different functional group chemistries (carboxyl, thiol, phosphate, and hydroxyl) and conformations (C11 and C16 chain lengths). We find rates are substrate-specific and obey predictions of classical nucleation theory at supersaturations that extend above the solubility of amorphous calcium carbonate. Analysis of the kinetic data shows the thermodynamic barrier to nucleation is reduced by minimizing the interfacial free energy of the system, ?. We then use dynamic force spectroscopy to independently measure calcite–substrate-binding free energies, ?Gb. Moreover, we show that within the classical theory of nucleation, ? and ?Gb should be linearly related. The results bear out this prediction and demonstrate that low-energy barriers to nucleation correlate with strong crystal–substrate binding. This relationship is general to all functional group chemistries and conformations. These findings provide a physical model that reconciles the long-standing concept of templated nucleation through stereochemical matching with the conventional wisdom that good binders are good nucleators. The alternative perspectives become internally consistent when viewed through the lens of crystal–substrate binding.

Hamm, Laura M.↗
DOE OSTI2020

Quarkyonic matter equation of state in beta-equilibrium

Quark matter may appear due to a hadronic-quark transition in the core of a hybrid star. Quarkyonic matter is an approach in which both quarks and nucleons appear as quasiparticles in a crossover transition, and provides an explicit realization of early ideas concerning quark matter (e.g., the MIT bag model). This description has recently been employed by McLerran and Reddy to model chargeless (pure neutron) matter with an approach that has the virtue that the speed of sound rises quickly at a neutron-quark transition so as to satisfy observational constraints on the neutron star maximum mass (≳ 2 $M_⊙$) and the radius of a 1.4 $M_⊙$ star ($R_{1.4}$ ≲ 13.5 km). Traditional models involving first-order transitions result in softer pressure-energy density relations that have difficulty satisfying these constraints except with very narrow choices of parameters. Here, we propose a variation of quarkyonic matter involving protons and leptons whose energy can be explicitly minimized to achieve both chemical and beta equilibrium, which cannot be done in the chargeless formulation. Quarkyonic stellar models are able to satisfy observed mass and radius constraints with a wide range of model parameters, avoiding the obligatory fine-tuning of conventional hybrid star models, including requiring the transition density to be very close to the nuclear saturation density. Our formulation fits experimental and theoretical properties of the nuclear symmetry energy and pure neutron matter, and contains as few as three free parameters. This makes it an ideal tool for the study of high-density matter that is an efficient alternative to piecewise polytrope or spectral decomposition methods.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2017

Cure Schedule for Stycast 2651/Catalyst 11.

The Henkel technical data sheet (TDS) for Stycast 2651/Catalyst 11 lists three alternate cure schedules for the material, each of which would result in a different state of reaction and different material properties. Here, a cure schedule that attains full reaction of the material is defined. The use of this cure schedule will eliminate variance in material properties due to changes in the cure state of the material, and the cure schedule will serve as the method to make material prior to characterizing properties. The following recommendation was motivated by (1) a desire to cure at a single temperature for ease of manufacture and (2) a desire to keep the cure temperature low (to minimize residual stress build-up associated with the cooldown from the cure temperature to room temperature) without excessively limiting the cure reaction due to vitrification (i.e., material glass transition temperature, T g , exceeding cure temperature).

36 MATERIALS SCIENCE↗
DOE OSTI2020

Improving Gas Reactor Design with Complex Non-Standard Reaction Mechanisms in a Reactive Flow Model

Fluorinated gases are critical to a number of high-technology industries including semiconductor manufacturing and related processes such as flat panel display, LED, and photovoltaic manufacturing. These fluorinated gases have very high global warming potentials (GWPs) and, unfortunately are chemically very stable, in some cases lasting for thousands of years in the atmosphere. For environmental reasons, it is imperative that the release of these gases be minimized, but existing methods to destroy them requires a significant amount of energy. The goal of this project was to develop a more energy efficient method of destroying these high GWP gases using computational fluid dynamics, but the computational requirements are significant. In this project, we bring together resources available at the national labs, including high-performance computing hardware and modern computational methods, in order to explore an industrially important problem with key environmental and economic impact. In this project, we examined the state-of-the-art models for the physical processes involved, and made subtle changes to arrive at alternative formulations considerably better suited for computation and study. We examined several representative scenarios and developed a set of analyses techniques and tools that could be used to explore the systems in much greater detail. This exploratory project has demonstrated to ALZETA that HPC can indeed provide a unique view into their complex engineering problem - one that is simply inaccessible by any other means. The tools allow us to explore the details of the chemical process, and allow one to construct "what-if" scenarios to address shortcomings of the physical device in its current operating modes. However, as with many sources of completely new information, many new questions are illuminated with this capability. It will take considerable time, effort and experience before we learn to probe the solutions, pose operating scenarios and confirm modifications to the device that lead to real engineering advances.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2010

Lightweight Heat Pipes Made from Magnesium

Magnesium has shown promise as a lighter-weight alternative to the aluminum alloys now used to make the main structural components of axially grooved heat pipes that contain ammonia as the working fluid. Magnesium heat-pipe structures can be fabricated by conventional processes that include extrusion, machining, welding, and bending. The thermal performances of magnesium heat pipes are the same as those of equal-sized aluminum heat pipes. However, by virtue of the lower mass density of magnesium, the magnesium heat pipes weigh 35 percent less. Conceived for use aboard spacecraft, magnesium heat pipes could also be attractive as heat-transfer devices in terrestrial applications in which minimization of weight is sought: examples include radio-communication equipment and laptop computers.

Rosenfeld, John N.↗
NASA NTRS2012

Microbial Monitoring of Pathogens by Comparing Multiple Real-Time PCR Platforms for Potential Space Applications

The International Space Station (ISS) is a closed environment wi~h rotations of crew and equipment each introducing their own microbial flora making it necessary to monitor the air, surfaces, and water for microbial contamination. Current microbial monitoring includes labor and time intensive methods to enumerate total bacterial and fungal cells with limited characterization during in-flight testing. Although this culture-based method has been sufficient for monitoring the ISS, future long duration missions will need to perform more comprehensive characterization in-flight, since sample return and ground characterization may not be available. A workshop was held in 2011 at the Johnson Space Center to discuss alternative methodologies and technologies suitable for microbial monitoring for these longterm exploration missions where molecular-based methodologies, such as polymerase chain reaction (PCR), were recommended. In response, a multi-center (Marshall Space Flight Center, Johnson Space Center, Jet Propulsion Laboratory, and Kennedy Space Center) collaborative research effort was initiated to explore novel commercial-off-the-shelf hardware options for spaceflight environmental monitoring. The goal was to evaluate quantitative/semi-quantitative PCR approaches to space applications for low cost in-flight rapid identification of microorganisms affecting crew safety. The initial phase of this project identified commercially available platforms that could be minimally modified to perform nominally in microgravity followed by proof-of-concept testing on the highest qualifying candidates with a universally available test organism, Salmonella enterica. The platforms evaluated during proof-of-concept testing included the iCubate 2.0(TradeMark) (iCubate, Huntsville, AL), RAZOR EX (BioFire Diagnostics; Salt Lake City, Utah) and SmartCycler(TradeMark) (Cepheid; Sunnyvale, CA). The analysis identified two potential technologies (iCubate 2.0 and RAZOR EX) that were able to perform sample-to-answer testing with cell sample concentrations between SO to 400 cells. In addition, the commercial systems were evaluated for initial flight safety and readiness, sample concentration needs were reviewed, and a competitive procurement of commercially available platforms was initiated.

Birmele, Michele↗
DOE OSTI2024

PWM for Simultaneous Minimization of Switching Losses and CM Voltage in Current Source Inverters

This article proposes a new pulsewidth modulation (PWM) scheme that reduces common-mode (CM) voltage and switching losses simultaneously in CSI. The proposed PWM [i.e., reduced voltages PWM (RVM)] reduces CM voltages and switching losses by selecting the optimal zero current vector and PWM sequence based on the CSI output voltage conditions. This article also proves the proposed RVM achieves both objectives (i.e., reduced CM voltage and switching losses) simultaneously for all CSI operating conditions without compromising the other objective. The proposed RVM inherently achieves zero-voltage switching (ZVS) conditions during the zero current vector transitions, further reducing the switching losses. Experimental results demonstrate significant reductions in CM voltage, reaching up to approximately 95%, accompanied by an increase of up to about 5.5% in CSI efficiency across a wide operating range compared to alternative PWM methods, confirming the predicted advantages of the proposed RVM.

42 ENGINEERING↗
DOE OSTI2017

Feasibility of Applying a Human Bio-signals Monitoring to Minimize Insider Threats

With the on-going global war on terror, a potential terrorist attack on a Nuclear Power Plant (NPP) is getting a lot of attention. In particular, the potential threat of an insider is a major concern as it could lead to the loss of a nationally critical asset and thus deserves serious consideration. The current approach to preventing an insider threat is the Insider Mitigation Program (IMP) based on periodic self-assessment or peer and manager review of specific employees. These are potentially biased and subjective assessments and are unreliable. Also, as the approach is reactive-based, identifying a problem employee could be too late to protect NPP assets (i.e., confidential information and nuclear materials). Thus, a new approach for detecting and predicting an insider is necessary. We propose a proactive approach based on using bio-signals as an alternative. To address the vulnerability of current insider detection systems, our studies investigated the possibility of insider detection and prediction by using biosignals (electroencephalogram (EEG), electrocardiogram (ECG), and galvanic skin response (GSR)). But one main question remained in the previous studies was: Is the method using key EEG indicators specific enough to discern the difference between a normal worker's motivation level change and being ready to commit a crime? This study examined the answer to the question.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Life cycle cost, energy, and carbon emissions of molds for precast concrete: Exploring the impacts of material choices and additive manufacturing

Molds for precast concrete are commonly used to create simple- to complex-shaped concrete products away from construction sites. These molds are often handmade from wood; however, additively manufacturing (AM, or 3D printing) fiber-reinforced polymer composites is an advantageous alternative, producing significantly more durable, highly complex molds faster, but likely at a higher cost. Here, this study explores the impact of material and production variables on the cost, energy, and carbon emissions of employing composite AM molds over the full lifecycle. The case study employed techno-economic and life cycle assessments to show that using wood flour–poly(lactic acid) or recycled carbon fiber–acrylonitrile butadiene styrene for AM molds can be less expensive than conventional wood molds, especially when considering use phase costs. While wood molds have the least environmental impacts due to wood's higher biogenic carbon sequestration and minimal processing, optimizing AM designs could reduce energy demand, carbon emissions, and cost.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Shadow energy functionals and potentials in Born–Oppenheimer molecular dynamics

In Born–Oppenheimer molecular dynamics (BOMD) simulations based on the density functional theory (DFT), the potential energy and the interatomic forces are calculated from an electronic ground state density that is determined by an iterative self-consistent field optimization procedure, which, in practice, never is fully converged. The calculated energies and forces are, therefore, only approximate, which may lead to an unphysical energy drift and instabilities. Here, we discuss an alternative shadow BOMD approach that is based on backward error analysis. Instead of calculating approximate solutions for an underlying exact regular Born–Oppenheimer potential, we do the opposite. Instead, we calculate the exact electron density, energies, and forces, but for an underlying approximate shadow Born–Oppenheimer potential energy surface. In this way, the calculated forces are conservative with respect to the approximate shadow potential and generate accurate molecular trajectories with long-term energy stabilities. We show how such shadow Born–Oppenheimer potentials can be constructed at different levels of accuracy as a function of the integration time step, δt, from the constrained minimization of a sequence of systematically improvable, but approximate, shadow energy density functionals. For each energy functional, there is a corresponding ground state Born–Oppenheimer potential. These pairs of shadow energy functionals and potentials are higher-level generalizations of the original “zeroth-level” shadow energy functionals and potentials used in extended Lagrangian BOMD. The proposed shadow energy functionals and potentials are useful only within this extended dynamical framework, where also the electronic degrees of freedom are propagated as dynamical field variables together with the atomic positions and velocities. The theory is quite general and can be applied to MD simulations using approximate DFT, Hartree–Fock, or semi-empirical methods, as well as to coarse-grained flexible charge models.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

All-Optical Cryogenic Thermometry Based on Nitrogen-Vacancy Centers in Nanodiamonds

The nitrogen-vacancy (N-V) center in diamond has been viewed as a high-sensitivity nanometer-scale metrology platform. Thermometry has been a current focus, with attention largely confined to room-temperature applications. Temperature sensing at low temperatures, yet, remains challenging as the sensitivity decreases for many commonly used techniques, which rely on a temperature-dependent frequency shift of the N-V center's spin resonance and its control with microwaves. Here we use an alternative method that does not require microwaves, ratiometric all-optical thermometry, and demonstrate that it may be utilized to liquid-nitrogen temperatures without deterioration of the sensitivity. The use of an array of nanodiamonds embedded within a portable polydimethylsiloxane sheet provides a versatile temperature-sensing platform that can probe a wide variety of systems without the configurational restrictions needed for applying microwaves. With this device, we observe a temperature gradient over tens of microns in a ferromagnetic-insulator substrate (yttrium iron garnet) under local heating by a resistive heater. This thermometry technique provides a cryogenically compatible, microwave-free, minimally invasive approach capable of probing local temperatures with few restrictions on the substrate materials.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1993

HL-20 subsystem design

The NASA Langley Research Center has been developing a lifting-body configuration called the HL-20 for potential application as a personnel launch system orbiter that will provide the crew changeout at the Space Station Freedom. The objectives have been to provide an alternate manned access to space with a more cost-effective, efficient, reliable, and safer system for the routine transportation of people to LEO. The detailed study of this concept includes the subsystem design, flight software sizing, and mass properties that are discussed in this paper. The goals were to develop a subsystem complement to maximize operational efficiency with minimum development costs while using current technology. Subsystem selection and trade studies showed that current technology components will provide the required performance and operational effectiveness. Many of the selected components have Shuttle flight histories or considerable development heritage from other programs that will help minimize development costs.

Stone, H. W.↗
NASA NTRS2003

Summary and Recommendations for Future Work

The safety of astronauts is the primary concern of all space missions. Space radiation has been identified as a major concern for ISS, and minimizing radiation risks during EVA is a principle component of NASA s radiation protection program. The space suit plays a critical role in shielding astronauts from EVA radiation exposures. In cooperation with the JSC Extravehicular Activity Project Office, and the Space Radiation Health Project Office, the NASA EMU and RSA Orlan space suits were taken to the LLUPTF for a series of measurements with proton and electron beams to simulate exposures during EVA operations. Additional tests with material layouts of the EMU suit sleeve were made in collaboration with NASA LaRC at the LBNL 88-inch cyclotron and at the Brookhaven National Laboratory Alternating Gradient Synchrotron.

Cucinotta, Francis A.↗
NASA NTRS2004

Status of the Landsat Data Continuity Mission

Efforts to begin implementing a successor mission to Landsat 7, called the Landsat Data Continuity Mission (LDCM), suffered a set back in 2003. NASA and the Department of Interior (DOI)/U.S. Geological Survey (USGS) currently manage the Landsat Program as an interagency partnership. The two agencies had planned to purchase data meeting LDCM specifications from a privately owned and commercially operated satellite system beginning in March, 2007. This approach represented a departure from the traditional procurement of a government owned and operated satellite system. NASA, however, cancelled a Request-for-Proposals (RFP) for providing the required data after an evaluation of proposals received from private industry. NASA concluded that the proposals failed to meet a key objective and expectation of the RFP, namely, to form a fair and equitable partnership between the Government and private industry. Alternative strategies for implementing an LDCM are now under consideration. The Executive Office of the President formed an interagency working group on the LDCM following the RFP cancellation. The working group is considering other options for implementing a successor system to Landsat 7 consistent with the Land Remote Sensing Policy Act of 1992 (Public Law 102-555). This Act lists four management options for consideration: 1) private sector funding and management; 2) an international consortium; 3) funding and management by the U.S. Government; and 4) a cooperative effort between the US. Government and the private sector. The working group is currently attempting to minimize the risk of a Landsat data gap through development of a strategy that leads to a Landsat 7 successor mission. The selected strategy and the status of the mission will be presented at the Symposium.

Irons, James R.↗