Results for “Advanced Manufacturing” — Page 74

NASA NTRS1984

Report of the Panel on Materials

Materials and manufacturing technology are critical to advanced aircraft and permeate all disciplines. Current aircraft systems employ a variety of materials, each selected to provide the best vehicle design in terms of performance, safety, reliability, manufacturability, and life cycle cost. However, a mistake in materials selection could bankrupt an airframe or engine manufacturer. Thus, the introduction of new materials is a slow process. Generally, new materials are used initially in noncritical components until their performance in service can be confirmed. Then, as confidence grows, they are used in more and more critical applications. Finally, if appropriate, new materials are used in critical, static elements and then in dynamic components. Thus, because the nominal time for development of a conventional monolithic material ranges from 5 to 10 years there is a 10- to 15- year lag between laboratory effort and introduction into service. Therefore, to assure the availability of materials suitable for production aircraft and engines in the year 2000, the concepts already must have been identified and must be progressing along evolutionary paths toward application. Trends, actual and projected, in the use of materials for commercial engines are shown in Figure 4-1. Related military applications are projected to follow similar paths. The new actor will be composites. The panel examined a wide range of materials important to all aspects of aircraft development, airframe structures, propulsion systems and for other important aircraft subsystems. These are addressed in the body of the report in terms of the current state of the art, opportunities for improvement, and barriers to achievement of projected benefits. This is followed by projections of the progress of technology that could be realized by the year 2000 with the application of appropriate resources.

Diefendorf, Russell J.↗

NASA NTRSDate not supplied

Manufacture of Hybrid Standard-Ply/Thin-Ply Carbon/Epoxy Panels for Notched Test Specimens

Weight is a critical metric for aerospace structures, and one possible way to reduce weight is to improve performance using hybrid standard-ply/thin-ply laminates from a single material system. Previous studies showed benefits for stiffness, strength, reduced damage after impact, and increased compression-after-impact strength for these hybrid laminates. Another study suggested that performance of compression-loaded notched hybrid laminate specimens performed better than standard-ply laminates under compression, but the standard-ply laminates performed better under tension loading. However, analysis predicted the failure load and mode better for the hybrid laminates. An analytical study determined several hybrid laminate designs to use in a follow-on testing regiment that is planned to further study the notched hybrid composite performance under compression and tension load. Described herein is a manufacturing method to efficiently manufacture hybrid laminates using automated fiber placement using a 16-tow head where 8 tows are standard-ply and 8 tows are thin-ply. The method saves time in that it eliminates the need to change spools of material when switching from standard-ply to thin-ply lamina, and reduces the waste associated with changing of spools. The method is ideal for small manufacturing operations or research facilities that have only a single head, and the method was successfully applied at the NASA Langley Research Center (LaRC) Integrated Structural Assembly of Advanced Composites (ISAAC) facility to manufacture nine panels that will be used for the follow-on notched specimen testing of hybrid and standard laminates.

composite↗

NASA NTRSDate not supplied

Manufacture of Hybrid Standard-Ply/Thin-Ply Carbon/Epoxy Panels for Notched Test Specimens

Weight is a critical metric for aerospace structures, and one possible way to reduce weight is to improve performance using hybrid standard-ply/thin-ply laminates from a single material system. Previous studies showed benefits for stiffness, strength, reduced damage after impact, and increased compression-after-impact strength for these hybrid laminates. Another study suggested that performance of compression-loaded notched hybrid laminate specimens performed better than standard-ply laminates under compression, but the standard-ply laminates performed better under tension loading. However, analysis predicted the failure load and mode better for the hybrid laminates. An analytical study determined several hybrid laminate designs to use in a follow-on testing regiment that is planned to further study the notched hybrid composite performance under compression and tension load. Described herein is a manufacturing method to efficiently manufacture hybrid laminates using automated fiber placement using a 16-tow head where 8 tows are standard-ply and 8 tows are thin-ply. The method saves time in that it eliminates the need to change spools of material when switching from standard-ply to thin-ply lamina, and reduces the waste associated with changing of spools. The method is ideal for small manufacturing operations or research facilities that have only a single head, and the method was successfully applied at the NASA Langley Research Center (LaRC) Integrated Structural Assembly of Advanced Composites (ISAAC) facility to manufacture nine panels that will be used for the follow-on notched specimen testing of hybrid and standard laminates.

composite↗

NASA NTRSDate not supplied

A Frank Discussion on Lessons Learned From Adopting and Applying NASA-STD-6030 for Spaceflight Systems

With the advancement and adoption of Additive Manufacturing (AM) for spaceflight systems, numerous lessons have been learned during the qualification and certification of AM components. The lessons learned covered in this presentation will provide an overview of the challenges faced by NASA centers and commercial partners working to design AM hardware that complies with NASA-STD-6030 Additive Manufacturing Requirements (AMR). Topics of interest include tailoring of requirements for specific projects, documentation requirements, and addressing conservative approaches towards mechanical property development and analysis. In addition to that, this presentation aims to impress that these lessons learned will influence the future revisions of the NASA technical standard to facilitate and advance AM technology adoption on NASA projects.

Additive Manufacturing↗

DOE OSTI2021

Performance Modeling of a Variable-Geometry Oscillating Surge Wave Energy Converter on a Raised Foundation

This paper analyzes the power capture potential, structural loadings, and costs associated with an oscillating surge wave energy converter (OSWEC) operating on a raised foundation. The raised OSWEC offers opportunities for reduced installation costs, improved energy production, and greater flexibility of deployment when compared with fixed-bottom models. In this investigation, we simulated several different foundation geometries using WEC-Sim to estimate power capture and structural loads. In an effort to maximize power capture, several cases in which flat plates of varying size were attached to the top of the foundation, under and parallel with the OSWEC, were also simulated. These plates were found to enhance power capture by preventing the wave-induced pressure from passing underneath the OSWEC, diverting this pressure toward the OSWEC instead. The OSWEC was simulated in the six Wave Energy Prize sea states, which were chosen as a representative sample of U.S. deployment sites. A first-order estimate of structural costs was calculated using the Wave Energy Prize ACE metric, with the foundation comprised predominantly of steel-reinforced concrete and the OSWEC comprised of A36 steel. Influence of foundation geometry on power capture, structural loadings, and ACE are topics of particular interest. This work has been inspired by advances in large-scale additive manufacturing techniques that have the potential to dramatically reduce the cost of subsea foundations. These advancements may enable cost-effective WEC systems to be deployed on raised foundations.

cost↗

DOE OSTI2024

Development and Evaluation of a Novel Fuel Injector Design Method using Hybrid-Additive Manufacturing (Final Report)

The widespread application of metal additive manufacturing (AM) technologies has enabled exploration of complex design spaces to achieve optimally performing components. Current optimization techniques make use of several advanced methods to provide designs that are superior to existing versions. However, they seldom discuss the manufacturability of the optimal designs. The objective of this project was to develop a design optimization tool that simultaneously optimizes fuel injector hardware and the combustor flow field with optimization functions and constraints that consider both combustor performance and manufacturability using advanced AM methods and post-processing. In this way, the resultant hardware design is inherently imbued with our most advanced knowledge of combustion physics and AM methods from its conception.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Evaluation of Hardware and Software Bill of Materials (HBOMs/SBOMs) Extraction Methods

Hardware and software bills of materials (HBOMs and SBOMs) provide important visibility into the components, dependencies, and supply chain relationships within programmable digital devices. This visibility is critical for advanced nuclear reactor applications, where use of common or shared hardware components, software libraries, suppliers, or manufacturing processes may create common cause failure (CCF) vulnerabilities despite apparent diversity. This paper evaluates current approaches for obtaining and analyzing HBOMs and SBOMs in support of CCF, diversity and defense-in-depth (D3) assessments, and begins to explore potential methods for artificial intelligence/machine learning-based analysis. The availability of BOM information from advanced reactor manufacturers and vendors, representative hardware and software categories found in advanced reactor systems continues to limit research [13]. This paper compares commonly used BOM formats, including CycloneDX, SPDX, and SWID. It also surveys publicly available tools for generating BOMs from source code, compiled binaries, and hardware-related information, noting limitations in language coverage, system age, and format interoperability. Finally, this paper evaluates methods for correlating BOM data with vulnerability and exploitability information, including VEX, CVE, and CWE resources. The findings indicate that publicly available nuclear-vendor BOMs are limited, making third-party extraction and research into novel analysis techniques necessary.

Cybersecurity↗

DOE OSTI2022

Progress and Prospects of Inorganic Solid-State Electrolyte-Based All-Solid-State Pouch Cells

Here, all-solid-state batteries have piqued global research interest because of their unprecedented safety and high energy density. Significant advances have been made in achieving high room-temperature ionic conductivity and good air stability of solid-state electrolytes (SSEs), mitigating the challenges at the electrode–electrolyte interface, and developing feasible manufacturing processes. Along with the advances in fundamental study, all-solid-state pouch cells using inorganic SSEs have been widely demonstrated, revealing their immense potential for industrialization. This review provides an overview of inorganic all-solid-state pouch cells, focusing on ultrathin SSE membranes, sheet-type thick solid-state electrodes, and bipolar stacking. Moreover, several critical parameters directly influencing the energy density of all-solid-state Li-ion and lithium–sulfur pouch cells are outlined. Finally, perspectives on all-solid-state pouch cells are provided and specific metrics to meet certain energy density targets are specified. This review looks to facilitate the development of inorganic all-solid-state pouch cells with high energy density and excellent safety.

25 ENERGY STORAGE↗

NASA NTRS1975

The NASA-Lewis/ERDA Solar Heating and Cooling Technology Program

The NASA Lewis Research Center plans to carry out a major role in the ERDA Solar Heating and Cooling Program. This role would be to create and test the enabling technology for future solar heating, cooling, and combined heating/cooling systems. The major objectives of the project are to achieve reduction in solar energy system costs, while maintaining adequate performance, reliability, life, and maintenance characteristics. The project approach is to move progressively through component, subsystem, and then system technology advancement phases in parallel with continuing manufacturing cost assessment studies. This approach will be accomplished principally by contract with industry to develop advanced components and subsystems. This advanced hardware will be tested to establish 'technology readiness' both under controlled laboratory conditions and under real sun conditions.

Couch, J. P.↗

NASA NTRSDate not supplied

Manufacturing Trials of Integrally Stiffened Composite Panels Using Automated Fiber Placement

Commercial aircraft structures are frequently manufactured from carbon-epoxy materials because of their weight and stiffness advantages compared to metallic materials. Wing cover panels are regularly manufactured using an automated fiber placement (AFP) process, but current design and manufacturing methodologies do not fully take advantage of the opportunities afforded by AFP. Design and manufacturing studies were undertaken at the NASA Langley Research Center at the Integrated Structural Assembly of Advanced Composites (ISAAC) facility to quantify manufacturing benefits and limitations associated with AFP to create structurally efficient integral stiffeners as an alternative to bonded or mechanically fastened stiffeners. This methodology could save weight and remove failure mechanisms by reducing the need for rivets and bonding materials since the stiffener plies are interleaved within the skin plies. The use of AFP with integral stiffeners can open the design space, but a fundamental, systematic evaluation of manufacturing limitations is necessary. Manufacturing trials are described herein, where considered manufacturing variables included stiffener location, stiffener course staggering, stiffener widths, stiffener intersections, and material thicknesses for both the skin and stiffener plies. The manufacturing process and lessons learned from each trial are described, including the most successful current design which contains staggered stiffeners, non-traditional laminate angles, and a combination of multiple material thicknesses within the same laminate.

Composite manufacturing↗

NASA NTRSDate not supplied

Manufacturing Trials of Integrally Stiffened Composite Panels Using Automated Fiber Placement

Commercial aircraft structures are frequently manufactured from carbon-epoxy materials because of their weight and stiffness advantages compared to metallic materials. Wing cover panels are regularly manufactured using an automated fiber placement (AFP) process, but current design and manufacturing methodologies do not fully take advantage of the opportunities afforded by AFP. Design and manufacturing studies were undertaken at the NASA Langley Research Center at the Integrated Structural Assembly of Advanced Composites (ISAAC) facility to quantify manufacturing benefits and limitations associated with AFP to create structurally efficient integral stiffeners as an alternative to bonded or mechanically fastened stiffeners. This methodology could save weight and remove failure mechanisms by reducing the need for rivets and bonding materials since the stiffener plies are interleaved within the skin plies. The use of AFP with integral stiffeners can open the design space, but a fundamental, systematic evaluation of manufacturing limitations is necessary. Manufacturing trials are described herein, where considered manufacturing variables included stiffener location, stiffener course staggering, stiffener widths, stiffener intersections, and material thicknesses for both the skin and stiffener plies. The manufacturing process and lessons learned from each trial are described, including the most successful current design which contains staggered stiffeners, non-traditional laminate angles, and a combination of multiple material thicknesses within the same laminate.

Automated Fiber Placement↗

NASA NTRSDate not supplied

PRIME ISS Ground Prototype

In Additive Manufacturing (AM) with metal powders, layers of material are deposited and fused to form metal 3D parts. However, in most cases, remnant powder still must be removed from interior cavities and channels to fully clean the part before use. Ground demonstrations such as ultrasonic cleaning have been proven to work during ground testing at MSFC and Florida State University. However, manufacturing in the low gravity environment of space introduces challenges to this powder removal. Therefore, if this concept could be demonstrated in microgravity, the ability to clean AM parts or contaminated parts can bring new advancements to in-space manufacturing (ISM). The goal of this work was to make significant progress on developing an ISS payload using the ultrasonic technology called Powder Removal in Microgravity Environments (PRIME). This would also create new opportunities for in-space manufacturing (ISM) and the additive manufacturing community to develop new standards and practices for powder removal and the cleaning of contaminated parts in space.

Microgravity↗

DOE OSTI2023

Advanced Module Architecture for Reduced Costs, High Durability and Significantly Improved Manufacturability (Final Report)

This project demonstrated a new module architecture (referred to herein as Glass/Glass) using silicone edge seals and an interlayer polymer that reduces manufacturing costs, significantly streamlines manufacturing processes, and reduces cap-ex costs while improving module reliability. A prototype manufacturing process to fabricate this new module architecture was demonstrated with a significantly improved process cycle time for the lamination step from the current industry standard of 13.5 minutes to approximately 30 seconds for each of the individual edge seal and internal polymer application steps. Samples are fabricated, strenuously stressed, and characterized to quantify the cost benefits, hardware capacities and accelerated stress performance of the new architecture. These results are being compared to a standard, laminated baseline architecture using a Glass/EVA/Glass or Glass/Thermoplastic/Glass design that traditionally has high moisture vapor transmission rates (MVTR).

14 SOLAR ENERGY↗

DOE OSTI2026

Demonstration and analysis of volumetric additive manufacturing via sub-orbital spaceflight testing

Computed Axial Lithography (CAL) represents a significant advancement in the emerging field of Volumetric Additive Manufacturing (VAM). CAL addresses key limitations of traditional photopolymer additive manufacturing technologies, by eliminating the need for layering and support structures. Unlike conventional methods, CAL prints components by illuminating all points within a desired geometry simultaneously, using tomographic reconstruction to form the object in a single step. This unique approach eliminates the relative motion between the object and the precursor material, enabling faster printing speeds and reducing the waste associated with support structures. However, CAL parts require post-processing steps before they can be utilized. CAL's core attributes make it particularly suited for In-Space Manufacturing (ISM), due to its fast fabrication times, wide breadth of materials it can use, and minimized footprint. CAL has been successfully demonstrated in microgravity during parabolic flight experiments. However to fully validate and understand CAL's behaviour in microgravity, all manufacturing and post-processing steps must be integrated. In June 2024, we conducted SpaceCAL Mission 3, testing this entire workflow on a suborbital flight aboard Virgin Galactic's SpaceShipTwo. During ~140 s of microgravity, the system autonomously manufactured and post-processed four parts using PEGDA700 resin. Post-flight analysis showed that 2/4 parts were recognisable, while others were distorted due to bubble formation from residual water droplets, off-axis optical aberrations, and non-uniform solvent rinsing. Despite these limitations, this study represents the first integrated CAL workflow in space, providing an initial experimental demonstration and analysis for closed-loop in-space manufacturing.

Waddell, Taylor [Department of Mechanical Engineer↗

NASA NTRS1995

An advanced arc track resistant airframe wire

Tensolite, a custom cable manufacturer specializing in high temperature materials as the dielectric medium, develops an advance arc track resistant airframe wire called Tufflite 2000. Tufflite 2000 has the following advantages over the other traditional wires: lighter weight and smaller in diameter; excellent wet and dry arc track resistance; superior dynamic cut-through performance even at elevated temperatures; flight proven performance on Boeing 737 and 757 airplanes; and true 260 C performance by utilizing Nickel plated copper conductors. This paper reports the different tests performed on Tufflite 2000: accelerated aging, arc resistance (wet and dry), dynamic cut through, humidity resistance, wire-to-wire abrasion, flammability, smoke, weight, notch sensitivity, flexibility, and markability. It particularly focuses on the BSI (British Standards Institute) dry arc resistance test and BSI wet arc tracking.

Beatty, J.↗

NASA NTRS1992

Planning for the semiconductor manufacturer of the future

Texas Instruments (TI) is currently contracted by the Air Force Wright Laboratory and the Defense Advanced Research Projects Agency (DARPA) to develop the next generation flexible semiconductor wafer fabrication system called Microelectronics Manufacturing Science & Technology (MMST). Several revolutionary concepts are being pioneered on MMST, including the following: new single-wafer rapid thermal processes, in-situ sensors, cluster equipment, and advanced Computer Integrated Manufacturing (CIM) software. The objective of the project is to develop a manufacturing system capable of achieving an order of magnitude improvement in almost all aspects of wafer fabrication. TI was awarded the contract in Oct., 1988, and will complete development with a fabrication facility demonstration in April, 1993. An important part of MMST is development of the CIM environment responsible for coordinating all parts of the system. The CIM architecture being developed is based on a distributed object oriented framework made of several cooperating subsystems. The software subsystems include the following: process control for dynamic control of factory processes; modular processing system for controlling the processing equipment; generic equipment model which provides an interface between processing equipment and the rest of the factory; specification system which maintains factory documents and product specifications; simulator for modelling the factory for analysis purposes; scheduler for scheduling work on the factory floor; and the planner for planning and monitoring of orders within the factory. This paper first outlines the division of responsibility between the planner, scheduler, and simulator subsystems. It then describes the approach to incremental planning and the way in which uncertainty is modelled within the plan representation. Finally, current status and initial results are described.

Fargher, Hugh E.↗

DOE OSTI2025

Myna: Connecting powder bed fusion build data to simulation tools for digital twin applications

Additive manufacturing (AM), as a digital process, can generate a detailed digital thread linking a part’s design and manufacturing to its operational performance. As AM systems advance, an increasing amount of process data is stored in manufacturing databases. In principle, this data can be utilized by simulation-based digital twin approaches, such as real-time process control and asynchronous post-processing guidance. However, few tools currently exist for systematically integrating digital thread data with computational tools. Here, in this study, we propose a software package, called Myna, for connecting data from powder bed fusion processes to simulation tools. The utility of such a platform is demonstrated using build data from the Oak Ridge National Laboratory Manufacturing Demonstration Facility “Peregrine v2023-10” public dataset to automatically configure and run 54 semi-analytical 3DThesis melt pool simulations, 78 numerical Additive FOAM melt pool simulations, and 3 ExaCA microstructure simulations. The simulated, spatially registered microstructures are then compared directly with electron backscatter diffraction characterization of the corresponding as-built part locations. The resulting simulated microstructure showed variation as a function of process parameters, particularly stripe width; however, the experimental data had little variation between the microstructure texture and grain size resulting from different processing conditions. Analysis of the discrepancies suggest that it is possible a two-phase ferritic-austenitic solidification model is needed to accurately predict grain size and texture for certain stainless steel 316L feedstock compositions under powder bed fusion conditions, providing direction for future research. As illustrated here, due to the number and complexity of the simulations involved in AM process-structure–property predictions, automated methods to connect process data and simulations will remain necessary tools for testing hypotheses and implementing digital twin applications.

Knapp, Gerald L. [Oak Ridge National Laboratory (O↗

DOE OSTI2024

Flexible Stellarator Physics Facility

We propose to build a Flexible Stellarator Physics Facility to explore promising regions of the vast parameter space of disruption-free stellarator solutions for Fusion Pilot Plants (FPPs). The FESAC Long Range Plan recognized the quasi-symmetric stellarator as “the leading US approach to developing disruption-free, low-recirculating-power fusion configurations”. To deliver the ambitious Decadal Vision for Commercial Fusion Energy, we must establish a persuasive stellarator program in parallel to the tokamak one: the stellarator will prove to be a better path to a reactor if theoretical predictions are confirmed and novel optimization techniques and strategies work as desired. Since the release of the Long Range Plan in 2020, stellarators have arguably made the most significant advances of all fusion concepts. Groundbreaking results from W7-X demonstrated low neoclassical transport and the successful operation of the island divertor. Advances in theory and modeling now allow us to minimize turbulent transport, to achieve equilibria with precise quasisymmetry, to reduce neoclassical transport and fast ion loss to levels far below what has been previously achieved, and to minimize the effect of coil manufacturing errors. If realized, these advances will lead to cost-effective stellarator designs with confinement comparable to tokamaks but without the fundamental challenges of disruptions and current drive.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗