Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ACOUSTIC TESTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,333 records · Page 74

Effect of inlet disturbances on fan inlet noise during a static test

Measurements of fan rotor inlet noise taken during static test situations are at variance with aircraft engine flight data. In particular, static tests generally yield a significantly higher tone at blade passage frequency than that measured during flight. To explain this discrepancy, the extent of the influence of inlet ground vortices and large-scale inlet turbulence on the forward-radiated fan noise measured at a static test facility was investigated. While such inlet disturbances were generated intentionally in an anechoic test chamber, far-field acoustic measurements and inlet flow-field hot-film mappings of a fan rotor were obtained. Experimental results indicate that the acoustic effect of such disturbances appears to be less severe for supersonic than for subsonic tip speeds. Further, a reverse flow that occurs on the exterior cowl in static test facilities appears to be an additional prime candidate for creating inlet disturbances and causing variance between flight and static acoustic data.

Bekofske, K. L.↗

Low speed wind tunnel investigation of the aerodynamic and acoustic performance of several sonic inlet takeoff and approach geometries

A series of tests was conducted to determine the aerodynamic and acoustic performance of several sonic inlet takeoff and approach geometries. The effects of inlet lip shape and diffuser length were also investigated. The tests were conducted in a low-speed wind tunnel at free-stream velocities of 0 and 45 meters per second. Inlet incidence angle was varied from 0 deg to 50 deg. The inlets were sized to fit a 13.97-centimeter-diameter fan. In terms of the highest level of inlet total pressure recovery for a given amount of noise suppression, a cylindrical centerbody takeoff geometry and a bulb-shaped centerbody approach geometry provided the best results over all conditions of free-stream velocity and incidence angle. Increasing inlet lip contraction ratio extended the maximum incidence angle for attached lip flow, while increasing inlet diffuser length resulted in a higher total pressure recovery for a given amount of noise suppression.

Abbott, J. M.↗

A Comparison of Impedance Eduction Test Rigs with Different Flow Profiles

The experimental characterization of acoustic liners applied for turbofan engines has been in the spotlight of the community for the last few decades. In general, such characterization is done by measurements of the liner acoustic impedance using different techniques in conditions as close as possible to those encountered in turbofan engines. Although a great amount of work has been published related to these techniques, few comparisons between different experimental setups using identical samples are available. The goal of the present study is to provide a comparison between educed acoustic impedances for two nominally identical liner samples in theUFSC Impedance Test Rig and the NASA Langley Research Center Grazing Flow ImpedanceTube (GFIT). Due to the geometrical differences between the test rigs, it is possible to consider the effect of different grazing flow profiles on the educed impedance. Impedance measurements between the two facilities show similar results in absence of grazing flow, while different ones when the grazing flow is present. Results are presented with both test rigs targeted to two different conditions: (i) same centerline Mach number and; (ii) same average Mach number.Both comparisons suggest a higher acoustic resistance obtained with the UFSC Impedance TestRig. A comparison using semi-empirical predictive models was also conducted. The results suggest that the main source for the observed difference is the grazing flow profile, represented by its boundary layer displacement thickness.

impedance↗

A Comparison of Impedance Eduction Test Rigs with Different Flow Profiles

The experimental characterization of acoustic liners applied for turbofan engines has been in the spotlight of the community for the last few decades. In general, such characterization is done by measurements of the liner acoustic impedance using different techniques in conditions as close as possible to those encountered in turbofan engines. Although a great amount of work has been published related to these techniques, few comparisons between different experimental setups using identical samples are available. The goal of the present study is to provide a comparison between educed acoustic impedances for two nominally identical liner samples in theUFSC Impedance Test Rig and the NASA Langley Research Center Grazing Flow ImpedanceTube (GFIT). Due to the geometrical differences between the test rigs, it is possible to consider the effect of different grazing flow profiles on the educed impedance. Impedance measurements between the two facilities show similar results in absence of grazing flow, while different ones when the grazing flow is present. Results are presented with both test rigs targeted to two different conditions: (i) same centerline Mach number and; (ii) same average Mach number.Both comparisons suggest a higher acoustic resistance obtained with the UFSC Impedance TestRig. A comparison using semi-empirical predictive models was also conducted. The results suggest that the main source for the observed difference is the grazing flow profile, represented by its boundary layer displacement thickness.

impedance↗

Experimental blade vortex interaction noise characteristics of a utility helicopter at 1/4 scale

Models of both the advanced main rotor system and the standard or "baseline" UH-1 main rotor system were tested at one-quarter scale in the Langley 4- by 7-Meter (V/STOL) Tunnel using the general rotor model system. Tests were conducted over a range of descent angles which bracketed the blade-vortex interaction phenomenon for a range of simulated forward speeds. The tunnel was operated in the open-throat configuration with acoustic treatment to improve the semi-anechoic characteristics of the test chamber. Acoustical data obtained for these two rotor systems operating at similar flight conditions are presented without analysis or discussion.

Conner, D. A.↗

Synergistic Development, Test, and Qualification Approaches for the Ares I and V Launch Vehicles

The U.S. National Aeronautics and Space Administration is designing and developing the Ares I and Ares V launch vehicles for access to the International Space Station (ISS) and human exploration of the Moon. The Ares I consists of a first stage reusable five-segment solid rocket booster, a upper stage using a J-2X engine derived from heritage experience (Saturn and Space Shuttle External Tank programs), and the Orion crew exploration vehicle (CEV). The Ares V is designed to minimize the development and overall life-cycle costs by leveraging off of the Ares I design. The Ares V consists of two boosters, a core stage, an earth departure stage (EDS), and a shroud. The core stage and EDS use LH2/LO2 propellants, metallic propellant tanks, and composite dry structures. The core stage has six RS-68B upgraded Delta IV engines while the EDS uses a J-2X engine for second stage ascent and trans-lunar injection (TLI) burn. System and propulsion tests and qualification approaches for Ares V elements are being considered as follow-on extensions of the Ares I development program. Following Ares I IOC, testing will be conducted to verify the J-2X engine's orbital restart and TLI burn capability. The Ares I upper stage operation will be demonstrated through integrated stage development and acceptance testing. The EDS will undergo similar development and acceptance testing with additional testing to verify aspects of cryogenic propellant management, operation of sub-systems in a space simulation environment, and orbital re-start of the main propulsion system. RS-68B certification testing will be conducted along with integrated core stage development and acceptance testing. Structural testing of the Ares V EDS and core stage propellant tanks will be conducted similar to the Ares I upper stage. The structural qualification testing may be accomplished with separate propellant tank test articles. Structural development and qualification testing of the dry structure will be pursued as part of the design and development process. Especially critical is the development test program for the composite structures. The Ares V payload shroud will undergo acoustic, vibration, structural qualification, and deployment testing in a space simulation environment. Similar to Ares I, requirements for full-scale structural dynamic testing are being studied. Both Ares I and Ares V include validation flight testing as part of the qualification programs.

Cockrell, Charles E.↗

Safety and Function Test Report for the Viryd CS8 Wind Turbine

This test was conducted as part of the U.S. Department of Energy's (DOE) Independent Testing project. This project was established to help reduce the barriers of wind energy expansion by providing independent testing results for small turbines. Several turbines were selected for testing at the National Wind Technology Center (NWTC) at the National Renewable Energy Laboratory (NREL) as a part of the Small Wind Turbine Independent Testing project. Safety and function testing is one of up to five tests that may be performed on the turbines. Other tests include duration, power performance, acoustic noise, and power quality. Viryd Technologies, Inc. of Austin, Texas, was the recipient of the DOE grant and provided the turbine for testing.

17 WIND ENERGY↗

Offshore Wind Turbines - Estimated Noise from Offshore Wind Turbine, Monhegan Island, Maine: Environmental Effects of Offshore Wind Energy Development

Deep C Wind, a consortium headed by the University of Maine will test the first U.S. offshore wind platforms in 2012. In advance of final siting and permitting of the test turbines off Monhegan Island, residents of the island off Maine require reassurance that the noise levels from the test turbines will not disturb them. Pacific Northwest National Laboratory, at the request of the University of Maine, and with the support of the U.S. Department of Energy Wind Program, modeled the acoustic output of the planned test turbines.

17 WIND ENERGY↗

Twin jet noise shielding for a supersonic cruise vehicle

An engine arrangement for a supersonic cruise vehicle (SCV) has been developed that shows promise for jet noise reduction without the performance penalties associated with mechanical suppressors and engine oversizing. This arrangement, wherein two engines are placed on top of the wing directly above two similarly-mounted engines below the wing, can produce 3 to 5 dB less noise below the aircraft flight path than when four engines are installed under the wing. This noise reduction is due to acoustic shielding of the upper jets by the lower jets. Test data are reviewed to verify this acoustical shielding phenomenon, and detailed takeoff trajectories are calculated to show the effects of sideline and flyover noise levels on constraining maximum range SCV configurations. Engine placement variation and differential throttling, wherein thrust is unloaded from the lower engine and added to the upper engine, are to be explored as means for maximizing the shielding effect.

Clauss, J. S., Jr.↗

Environmental Test Program for the Mars Exploration Rover Project

On June 10 and July 7, 2003 the National Aeronautics and Space Administration (NASA) launched two spacecraft from Cape Canaveral, Florida for a six (6) months flight to the Red Planet, Mars. The two Mars Exploration Rover spacecraft landed safely on the planet in January 2004. Prior to the successful launch, both of the spacecraft were involved in a comprehensive test campaign that included development, qualification, and protoflight test programs. Testing was performed to simulate the environments associated with launch, inter-planetary cruise, landing on the planet and Mars surface operations. Unique test requirements included operating the spacecraft while the chamber pressure was controlled to simulate the decent to the planet from deep space, high impact landing loads and rover operations on the surface of the planet at 8 Torr and -130 C. This paper will present an overview of the test program that included vibration, pyro-shock, landing loads, acoustic noise, thermal vacuum and solar simulation testing at the Jet Propulsion Laboratory (JPL) Environmental Test Laboratory facilities in Pasadena, California.

Fisher, Terry C.↗

Environmental test program for the Mars Exploration Rover Project

This paper will present an overview of the test campaign that included vibration, pyro-shock, landing loads, acoustic noise, thermal vacuum and solar simulation testing at the Jet Propulsion Laboratory Environmental Test Laboratory facilities in Pasadena, California.

Van Velzer, Paul L.↗

Validation of Noise Propagation for Lined Inlets

Commercial finite element modeling tools are validated for use on inlet radiated noise predictions for an acoustically lined subsonic aircraft inlet tested in the NASA Glenn 9-foot by 15-foot low-speed wind tunnel. An in-depth review and prediction of the acoustic liner properties on the Advanced Ducted Propulsor were conducted for use in the noise predictions. Agreement between the inlet radiated noise predictions to the measured tones at approach was used as the validation for the prediction tools. Similar follow-up predictions were conducted for an acoustically lined supersonic inlet. A follow-up investigation on the effect of the acoustic liner placement within the supersonic inlet was undertaken.

Acoustics↗

Study and development of acoustic treatment for jet engine tailpipes

A study and development program was accomplished to attenuate turbine noise generated in the JT3D turbofan engine. Analytical studies were used to design an acoustic liner for the tailpipe. Engine ground tests defined the tailpipe environmental factors and laboratory tests were used to support the analytical studies. Furnace-brazed, stainless steel, perforated sheet acoustic liners were designed, fabricated, installed, and ground tested in the tailpipe of a JT3D engine. Test results showed the turbine tones were suppressed below the level of the jet exhaust for most far field polar angles.

Nelson, M. D.↗

Quantification of air leakage paths: a comparison of airflow and acoustic measurements

Today, the fan pressurization method is the most frequently used method to evaluate a building's airtightness. However, the localization and quantification of leaks remain difficult. In this paper, an acoustic method is introduced to estimate the leakage size of single leaks. Acoustic and airflow measurements were conducted and compared in laboratory tests within the same boundary conditions. This work aims to investigate if various leak sizes can be predicted using acoustic measurement methods. The test apparatus consists of two chambers, separated by a test wall. This wall represents a single characteristic air leakage path. Various types of wall structures with different slit geometries, wall thicknesses, and insulation materials were investigated. The acoustic measurements were performed with a sound source placed in one chamber and ultrasonic microphones located in both chambers. These results were compared to measured airflows through the test wall to provide estimates of uncertainty in the acoustic approach, which indicate a linear trend. Finally, these laboratory measurements were compared to the same measurements at a real office building. Finally, although the acoustic measurement uncertainty is still significant (greater than +/- 50%), the acoustic method has the potential to give an order of magnitude of single leak sizes.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Acoustic Predictions of Manned and Unmanned Rotorcraft Using the Comprehensive Analytical Rotorcraft Model for Acoustics (CARMA) Code System

The Comprehensive Analytical Rotorcraft Model for Acoustics (CARMA) is being developed under the Quiet Aircraft Technology Project within the NASA Vehicle Systems Program. The purpose of CARMA is to provide analysis tools for the design and evaluation of efficient low-noise rotorcraft, as well as support the development of safe, low-noise flight operations. The baseline prediction system of CARMA is presented and current capabilities are illustrated for a model rotor in a wind tunnel, a rotorcraft in flight and for a notional coaxial rotor configuration; however, a complete validation of the CARMA system capabilities with respect to a variety of measured databases is beyond the scope of this work. For the model rotor illustration, predicted rotor airloads and acoustics for a BO-105 model rotor are compared to test data from HART-II. For the flight illustration, acoustic data from an MD-520N helicopter flight test, which was conducted at Eglin Air Force Base in September 2003, are compared with CARMA full vehicle flight predictions. Predicted acoustic metrics at three microphone locations are compared for limited level flight and descent conditions. Initial acoustic predictions using CARMA for a notional coaxial rotor system are made. The effect of increasing the vertical separation between the rotors on the predicted airloads and acoustic results are shown for both aerodynamically non-interacting and aerodynamically interacting rotors. The sensitivity of including the aerodynamic interaction effects of each rotor on the other, especially when the rotors are in close proximity to one another is initially examined. The predicted coaxial rotor noise is compared to that of a conventional single rotor system of equal thrust, where both are of reasonable size for an unmanned aerial vehicle (UAV).

Boyd, D. Douglas, Jr.↗

Ultrasonic emission method enables testing of adhesive bonds

Detection of acoustic energy emitted by adhesive bonds subjected to tensile stresses at frequencies above sixteen kilocycles per second is used as a method for determining bond strength. This method is used in measuring adhesive bond strengths on metal honeycomb core panels.

Frank, L.↗