Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wind engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,315 records · Page 73
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Comparison of ground and flight test results using a modified F106B aircraft

Two aft underwing nacelles housing afterburning J85 engines were added to an F106 to study exhaust nozzles in flight at Mach numbers up to 1.3. Installation effects were determined for several nozzles by comparing flight data to data from an isolated wind tunnel model. Reynolds number effects were studied at subsonic flight speeds for nozzles intended for use with afterburning turbofan engines. A wide range of Reynolds number was obtained by flying the F106 over a range of altitude and by using 5 and 22% wind tunnel models of the F106. A contoured nozzle had a boattail drag as low as that of a longer circular arc nozzle over the Reynolds number range studied.

Wilcox, F. A.↗
NASA NTRS1991

Comparison of heating rate calculations with experimental data on a modified Shuttle orbiter at Mach 6

Heating-rate calculations from an 'engineering' code and a 'benchmark' Navier-Stokes code are compared with experimental wind tunnel data obtained on a 'modified' 0.0075-scale Shuttle orbiter at a Mach number of 6 and a freestream Reynolds number of 1.9 x 10 to the 6th/m. Comparisons are presented along the windward symmetry plane, in a circumferential direction around the body, and along the wing leading edge at angles of attack of 30 and 40 deg. Both codes provide accurate predictions of the heating rate over most of the body, but because the run time for the engineering code is relatively short, it is an ideal tool for both parametric and design studies.

Hamilton, H. H., II↗
NASA NTRS1970

Hypersonic research engine project. Phase 2: Structures and cooling development

The structures assembly model (SAM) was installed, and wind tunnel systems were checked out. The first run, with hydrogen cooling and SAM inserted in the wind tunnel stream (M = 7.7, P sub TOTAL = 900 psia, T sub TOTAL = 2500 deg R), was accomplished. The condition of the SAM after the run was satisfactory, with no visible signs or data indications of overheating or overloading.

Jilly, L. F.↗
NASA NTRS1981

Full-scale aerodynamic characteristics of a propellar installed on a small twin-engine aircraft wing panel

Full-scale measurements of shaft thrust and torque were made. Wind-tunnel speeds and blade angles were set for full-scale flight conditions. Excellent quality measurements were obtained of the thrust coefficient, the power coefficient, and the propeller efficiency for various values of the advance ratio and the blade incidence angle at 3/4-blade radius. A conventional propeller theory found in the literature was applied to the present results. Although thrust, power, and efficiency were somewhat overpredicted, the advance ratio for maximum efficiency was predicted quite accurately. It was found that, for some conditions, spinner drag could be significant. A simple correction that was based on the spinner base pressure substantially accounted for the changes in efficiency that resulted from this cause.

Barlow, P. R.↗
NASA NTRSDate not supplied

Global Reference Atmospheric Model (GRAM) Advancements and Additions

Introduction:The Global Reference Atmospheric Model (GRAM) is one of the most widely used engineering models of the atmosphere. GRAM development and maintenance has been led by NASA Marshall Space Flight Center (MSFC). The NASA Science Mission Directorate (SMD) has provided funding support to upgrade the GRAMs since Fiscal Year 2018. NASA Langley Research Center has been working with MSFC on the upgrades.This presentation will provide details regarding the upgrades that have been made to the existing GRAMs, the development of new GRAMs, as well as the ongoing objectives, tasks, and milestones re-lated to the GRAM upgrades funded by NASA SMD. GRAM: The GRAMs are engineering-oriented atmospheric models that estimate mean values and statistical variations of the atmospheric properties for numerous planetary destinations.They provide mean values and variability for any point in the atmosphere as well as seasonal, geographic, and altitude variations. GRAM outputs include atmospheric density, temperature, pressure, winds, and chemical composition along a user-defined path.Theyhave been widely used by the engineering community because of their ability to create realistic dispersions. GRAMs have been integrated into high fidelity flight dynamic simulations of launch, entry, descent and landing (EDL), aerobraking and aerocapture. MSFC has been developing and updating GRAMs since 1974; GRAMs are currently available for Earth, Mars, Venus, Neptune, and Titan. GRAM Upgrade Status: Code Moderization.The planetary GRAMs are being rearchitected from Fortran to a common object-ori-entedC++ framework called the GRAM Suite. This new architecture creates a common GRAM library of data models and utilities. The first C++ releases of the existing planetary GRAMs (Mars, Venus, Neptune, and Titan-GRAM) in the GRAM Suite are straight conversions from the latest Fortran version. Model Upgrades.The focus of the model upgrade task is to improve the atmosphere models in the existing GRAMs and to establish a foundation for developing GRAMs for additional destinations. The GRAM ephemerishas been upgraded to the NASA Navigation and Ancillary Information Facility (NAIF) SPICE toolkit (version N0066). The calculation of the speed of sound has also been improved in the GRAMs. The GRAM team has received updated Mars General Circulation Model (MGCM) datasets from NASA Ames Research Center. Mars Global Ionosphere-Thermosphere Model (M-GITM) data is being obtained toreplace the Mars Thermospheric General Circulation Model (MTGCM) data in legacy Mars-GRAM. M-GITM and updated MGCM data will be incorporated into a future GRAM Suite release.Twoprojects that will improve the atmospheric model data in the GRAMs have been funded by the GRAM team since Fiscal Year 2020. Sanjay Limaye and Patrick Fry at the University of Wisconsin are reanalyzing the Venus Express radio occultation observations and analyzing the Akatsukiradio occultation observations.This will lead tothe calculation of number density, temperature, and pressure profiles for the 40-90 km altitude range. Kunio Sayanagi, Justin Garland, and Ryan McCabeat Hampton University are developing empirical global models for Venus,Jupiter, Saturn, Uranus, Neptune, and Titan that incorporates the latest data available for each of these planetary destinations. Upgraded GRAM Releases. GRAM Suite Version 1.0 was released in May 2020 and contains the rearchitected Neptune-GRAM, including the common GRAM framework and planet–specific code. GRAM Suite Version 1.1 was released in September 2020 and addedthe rearchitected Titan-GRAM to the GRAM Suite. A User Guide and Programmer’s Manualarereleased with all GRAMs. The rearchitected Mars and Venus-GRAMs will be released in upcomingversions of the GRAM Suite. New GRAM Releases. New GRAMs have been de-veloped for Uranus and Jupiter. Uranus-GRAM is based on an individual profile generated by Gary Allen (ARC) from Voyager 2 occultation data and will be released in GRAM Suite Version 1.2. Jupiter-GRAM is based on individual profile produced from Al Seiff’s Ju-piter model[1].Jupiter-GRAM will be released in GRAM Suite Version 1.3. Saturn-GRAM is currently under development and will be released in a future version of the GRAM Suite. Conclusions: GRAMs are vital and frequently used toolsets. Releases of the GRAM Suite, upgrades of the existing planetary GRAMs, and development of new planetary GRAMs are ongoing. NASA SMD funding has been essential to addressing current limitations and accomplishing GRAM developmental goals. Continua-tion ofSMD fundingwill ensure the development, up-grades, and maintenance of the GRAMs. References: [1] Seiff, A., et al. (1998) JGR, 103, 22,857-22,889. Acknowledgments: The authors gratefully acknowledge support from the NASA SMD

atmospheric models↗
DOE OSTI2022

Centrifuge modeling and numerical analysis on lateral performance of mono-bucket foundation for offshore wind turbines

The lateral loading performance of the mono-bucket foundation for offshore wind turbines is investigated in this study through a series of centrifuge tests and numerical analysis. Six mono-bucket models are considered to assess the influences of aspect ratio under the ultimate condition. The FE model is validated against the centrifuge test results, and the failure mechanism of the foundation is revealed. The parametric study and sensitivity analysis of the soil parameters are performed in the numerical simulations. A modified theoretical calculation method is proposed to estimate the ultimate lateral capacity of the suction bucket foundation by solving the limit equilibrium equations. A correction term is added in the calculation using the “m” method. The position of the rotation center is calculated, demonstrating a better accuracy compared to the previously reported geometric method. The modified calculation method is verified against the field test, the centrifuge test, and the laboratory test. The method is proved to be applicable in estimating the lateral performance of the mono-bucket foundation in a general form. Finally, this study aims to provide well-documented data and design references for practical engineers.

17 WIND ENERGY↗
NASA NTRS1986

Simulation investigation of the effect of the NASA Ames 80-by 120-foot wind tunnel exhaust flow on light aircraft operating in the Moffett field trafffic pattern

A preliminary study of the exhaust flow from the Ames Research Center 80 by 120 Foot Wind Tunnel indicated that the flow might pose a hazard to low-flying light aircraft operating in the Moffett Field traffic pattern. A more extensive evaluation of the potential hazard was undertaken using a fixed-base, piloted simulation of a light, twin-engine, general-aviation aircraft. The simulated aircraft was flown through a model of the wind tunnel exhaust by pilots of varying experience levels to develop a data base of aircraft and pilot reactions. It is shown that a light aircraft would be subjected to a severe disturbance which, depending upon entry condition and pilot reaction, could result in a low-altitude stall or cause damage to the aircraft tail structure.

Streeter, Barry G.↗
NASA NTRS2002

Global Reference Atmospheric Model and Trace Constituents

Global Reference Atmospheric Model (GRAM-99) is an engineering-level model of the Earth's atmosphere. It provides both mean values and perturbations for density, temperature, pressure, and winds, as well as monthly- and geographically-varying trace constituent concentrations. From 0-27 km, thermodynamics and winds are based on National Oceanic and Atmospheric Administration Global Upper Air Climatic Atlas (GUACA) climatology. Above 120 km, GRAM is based on the NASA Marshall Engineering Thermosphere (MET) model. In the intervening altitude region, GRAM is based on Middle Atmosphere Program (MAP) climatology that also forms the basis of the 1986 COSPAR Intemationa1 Reference Atmosphere (CIRA). MAP data in GRAM are augmented by a specially-derived longitude variation climatology. Atmospheric composition is represented in GRAM by concentrations of both major and minor species. Above 120 km, MET provides concentration values for N2, O2, Ar, O, He, and H. Below 120 km, species represented also include H2O, O3, N2O, CO, CH, and CO2. Water vapor in GRAM is based on a combination of GUACA, Air Force Geophysics Laboratory (AFGL), and NASA Langley Research Center climatologies. Other constituents below 120 km are based on a combination of AFGL and h4AP/CIRA climatologies. This report presents results of comparisons between GRAM Constituent concentrations and those provided by the Naval Research Laboratory (NRL) climatology of Summers (NRL,/MR/7641-93-7416, 1993). GRAM and NRL concentrations were compared for seven species (CH4, CO, CO2, H2O, N2O, O2, and O3) for months January, April, July, and October, over height range 0-115 km, and latitudes -90deg to + 90deg at 10deg increments. Average GRAM-NRL correlations range from 0.878 (for CO) to 0.975 (for O3), with an average over all seven species of 0.936 (standard deviation 0.049).

Justus, C.↗
NASA NTRS1988

Lewis Structures Technology, 1988. Volume 3: Structural Integrity Fatigue and Fracture Wind Turbines HOST

The charter of the Structures Division is to perform and disseminate results of research conducted in support of aerospace engine structures. These results have a wide range of applicability to practioners of structural engineering mechanics beyond the aerospace arena. The specific purpose of the symposium was to familiarize the engineering structures community with the depth and range of research performed by the division and its academic and industrial partners. Sessions covered vibration control, fracture mechanics, ceramic component reliability, parallel computing, nondestructive evaluation, constitutive models and experimental capabilities, dynamic systems, fatigue and damage, wind turbines, hot section technology (HOST), aeroelasticity, structural mechanics codes, computational methods for dynamics, structural optimization, and applications of structural dynamics, and structural mechanics computer codes.

Source record↗
NASA NTRS1954

Preliminary Data on the Effects of Inlet Pressure Distortions on the J57-P-1 Turbojet Engine

An investigation to determine the steady-state and surge characteristics of the J57-P-1 two-spool turbojet engine with various inlet air-flow distortions was conducted in the altitude wind tunnel at the NACA Lewis laboratory. Along with a uniform inlet total-pressure distribution, one circumferential and three radial pressure distortions were investigated. Data were obtained over a complete range of compressor speeds both with and without intercompressor air bleed at a flight Mach number of 0.8 and at altitudes of 35,000 and 50,000 feet. Total-pressure distortions of the magnitudes investigated had very little effect on the steady-state operating line for either the outer or inner compressor. The small radial distortions investigated also had engine over that obtained with the uniform inlet pressure distribution. The circumferential distortion, however, raised the minimum speed at which the engine could operate without encountering surge when the intercompressor bleeds were closed. This increase in minimum speed resulted in a substantial reduction in the operable speed range accompanied by a reduction in the altitude operating limit.

Wallner, Lewis E.↗
NASA NTRSDate not supplied

Computational Aerodynamic Analysis in Support of the CRM Tail Cone Thruster Configuration Wind Tunnel Test

NASA’s Advanced Air Transport Technology (AATT) project is breaching the boundaries of aircraft design in pursuit of eco-friendly solutions that are compatible with urban noise comfort levels. Boundary layer ingesting (BLI) propulsion systems promise to reduce fuel burn with additional potential benefits in noise reduction. Type-II BLI systems of the STARC-ABL type are the subject of a test campaign planned for fiscal year 2022 in the National Transonic Facility (NTF), for which a CRM-based model with a retrofitted tail cone thruster (TCT) has been designed. The present work is a precursor to the NTF test, where the 240 cases planned for the experiment were simulated using the Launch, Ascent and Vehicle Aerodynamics (LAVA)computational framework. Solution sensitivity to angle of attack, engine operating conditions, and the presence of the supporting structure (sting) in the wind tunnel test are analyzed in the extensive dataset. The main flow features contributing to the inlet distortion are identified as the vertical tail wake, wing downwash and fuselage upsweep vortices, with the latter two experiencing the greatest sensitivity to angle of attack. Finally, results from an inlet-guide-vane(IGV) design/integration study are presented. The LAVA team and the turbomachinery design team at NASA’s Ames and Glenn Research Centers are collaborating in an effort to reduce flow distortion upstream of the fan by means of integrating an IGV system into the CRM-TCT model. A significant improvement in flow distortion metrics has been achieved since the initial design iteration. Results employing an actuator zone model with realistic radially-varying thrust profiles to simulate first-order fan effects within LAVA are presented.

AATT↗
DOE OSTI2025

Gaussian FLOWERS: Wind-rose-based analytical integration of Gaussian wake model for extremely fast AEP estimation

A major cost in the study of wind farm layout optimization is the repeated evaluation of the annual energy production (AEP). The current approach to estimating AEP requires a large set of flow simulations to be performed that cover each discrete wind speed and direction combination contained within the wind rose, followed by a probability-weighted sum of the power production resulting from each simulation. Even with inexpensive engineering wake models, this numerical integration scheme can lead to high computational costs. In this paper, we derive an analytical formulation for estimating farm AEP across every wind direction, based on a Gaussian wake velocity model, which reduces the number of wind farm simulations to a single function evaluation. As a result, we find that the Gaussian-FLOWERS approach reduces the time for AEP calculations by more than two orders of magnitude with a small trade-off in accuracy when compared to a conventional approach. This massive reduction in computation cost is useful to reduce overall costs in wind farm layout optimization studies.

17 WIND ENERGY↗
NASA NTRS2012

A Turbine Based Combined Cycle Engine Inlet Model and Mode Transition Simulation Based on HiTECC Tool

An inlet system is being tested to evaluate methodologies for a turbine based combined cycle propulsion system to perform a controlled inlet mode transition. Prior to wind tunnel based hardware testing of controlled mode transitions, simulation models are used to test, debug, and validate potential control algorithms. One candidate simulation package for this purpose is the High Mach Transient Engine Cycle Code (HiTECC). The HiTECC simulation package models the inlet system, propulsion systems, thermal energy, geometry, nozzle, and fuel systems. This paper discusses the modification and redesign of the simulation package and control system to represent the NASA large-scale inlet model for Combined Cycle Engine mode transition studies, mounted in NASA Glenn s 10- by 10-Foot Supersonic Wind Tunnel. This model will be used for designing and testing candidate control algorithms before implementation.

Csank, Jeffrey T.↗
DOE OSTI2015

Final Report for Grant DOE DE-FG02-08ER64573 (Relating to Turbulence Modeling)

Turbulence enhances transport and mixing. Turbulent ocean currents can increase the encounter rate between fish larvae and their prey. Without turbulence, the fuel and air injected into the cylinder of an internal combustion engine would mix too slowly to be effective. Birds extract energy from turbulent winds to soar for great distances without flapping their wings. Turbulence can be detrimental as well. The efficiencies of vehicles, pipelines, and industrial equipment are all hindered by turbulence. Turbulence can also cause structural fatigue, generate unwanted noise, and distort the propagation of electromagnetic signals. These observations highlight the importance of turbulence research. Our ability to predict and control turbulence and, thus, to intensify or suppress its effects as circumstances warrant is contingent on our understanding of the underlying mechanisms. Turbulence is also immensely interesting from a purely scientific perspective and is a great source of fundamentally important, challenging problems for physicists, engineers, and mathematicians. Moreover, various methods and tools developed in the field have found applications in other fields, including nonlinear optics, nonlinear acoustics, pattern formation, image processing, data compression, and econophysics. It is possible, at least away from walls, to derive LES models of very high-order accuracy. However, these models also lead to correspondingly intense computational complexity for their numerical solution. Some also introduce yet more questions on the already difficult problem of specifying needed and sometimes artificial local boundary conditions for the inherently nonlocal flow averages. For these two (and other) reasons, there has been a resurgence of interest in basing simulations of turbulent flows on much simpler regularizations of the Navier–Stokes equations rather than on full models of local averages--i.e., LES models. Initially these were developed as pure theoretical tools. The influx of ideas from LES and the added constraint that the regularization be amenable to numerical simulation have breathed new perspective and thus new life into this thread of ideas.Over the past year, a significant portion of our research activity has focused on numerical studies of the Navier–Stokes-$αβ$ model and extensions thereof. Our results regarding these and other approaches to turbulence modeling are described below.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS2004

Analysis of Droplet Size during the Ice Accumulation Phase Of Flight Testing

There are numerous hazards associated with air travel. One of the most serious dangers to the pilot and passengers safety is the result of flying into conditions which are conducive to the formation of ice on the surface of an aircraft. Being a pilot myself I am very aware of the dangers that Icing can pose and the effects it can have on an airplane. A couple of the missions of the Icing branch is to make flying safer with more research to increase our knowledge of how ice effects the aerodynamics of an airfoil, and to increase are knowledge of the weather for better forecasting. The Icing Branch uses three different tools to determine the aerodynamic affects that icing has on a wing. The Icing research tunnel is an efficient way to test various airfoils in a controlled setting. To make sure the data received from the wind tunnel is accurate the Icing branch conducts real flight tests with the DHC-6 Twin Otter. This makes sure that the methods used in the wind tunnel accurately model what happens on the actual aircraft. These two tools are also compared to the LEWICE code which is a program that models the ice shape that would be formed on an airfoil in the particular weather conditions that are input by the user. One benefit of LEWICE is that it is a lot cheaper to run than the wind tunnel or flight tests which make it a nice tool for engineers designing aircraft that don t have the money to spend on icing research. Using all three of these tools is a way to cross check the data received from one and check it against the other two. industries, but it is also looked at by weather analysts who are trying to improve forecasting methods. The best way to avoid the troubles of icing encounters is to not go into it in the first place. By looking over the flight data the analyst can determine which conditions will most likely lead to an icing encounter and then this information will aid forecasters when briefing the pilots on the weather conditions. am looking at the weather data from certain flights and analyzing the type of precipitation that the plane is flying through. During flight tests there is a probe on the bottom of the aircraft that gathers information on the size and shape of the particles that it is flying through. The data can then be viewed on a computer. After grouping the weather into certain groups we can then pick certain groups which we think should be analyzed farther. The goal is to remove all the ice particles because they do not contribute to the icing on an aircraft. We use a 2D analyzer which measures the droplet size and categorizes the drops into bins of certain sizes. We can then look at what the characteristics of the weather that we were flying through such as the temperature and dew point and compare this with the size of the drops that the 2D analyzer measured. We can then look at what type and shape of ice that formed on the wing during this time period. Having this data will help us to reproduce these conditions using LEWICE and the wind tunnel. Having consistency among the tests will make things more accurate. With respect to weather forecasting we will be able to learn which conditions can lead to icing. Better accuracy in weather reporting will lead to fewer run-ins with icing which will also lead to fewer accidents.

Miller, Eric James↗
DOE OSTI2023

Forecasting for the Weather Driven Energy System - A New Task under IEA Wind

The energy system needs a range of forecast types for its operation in addition to the narrow wind power forecast that has been the focus of considerable recent attention. Therefore, the group behind the former IEA Wind Task 36 Forecasting for Wind Energy has initiated a new IEA Wind Task with a much broader perspective, which includes prospective interaction with other IEA Technology Collaboration Programmes such as the ones for PV, hydropower, system integration, hydrogen etc. In the new IEA Wind Task 51 (entitled "Foreacsting for the Weather Drive Energy System") the existing Work Packages (WPs) are complemented by work streams in a matrix structure. The Task is divided in three WPs according to the stakeholders: WP1 is mainly aimed at meteorologists, providing the weather forecast basis for the power forecasts. In WP2, the forecast service vendors are the main stakeholders, while the end users populate WP3. The new Task 51 started in January 2022. Planned activities include 4 workshops. The first will focus on the state of the art in forecasting for the energy system plus related research issues and be held during September 2022 in Dublin. The other three workshops will be held later during the 4-year Task period and address (1) seasonal forecasting with emphasis on Dunkelflaute, storage and hydro, (2) minute-scale forecasting, and (3) extreme power system events. The issues and conclusions of each of the workshops will be documented by a published paper. Additionally, the Recommended Practice on Forecast Solution Selection will be updated to reflect the broader perspective.

geophysics computing↗
NASA NTRS1974

Effects of the air breathing engine plumes on SSV orbiter subsonic wing pressure distributions (OA57A)

Experimental aerodynamic pressure investigations were conducted on a 0.0405 scale representation of the -89 space shuttle orbiter ferry configuration in the Rockwell International 7.75 x 11.00 foot Low Speed Wind Tunnel. The primary test objective was to investigate the orbiter wing pressure distribution resulting from five under-wing engine nacelle plumes. Two five engine nacelle configurations were tested at 3 ground plane heights with pressure bug measurements being made on the left upper and lower wing panel. In addition, base and balance cavity pressure measurements were made, with elevon normal and hinge moment measurements on the right panel.

Cameron, B. W., Jr.↗