Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wind data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,315 records · Page 73
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Estimation of peak winds from hourly observations

Two closely related methods to obtain estimates of the hourly peak wind at Cape Kennedy were compared by statistical tests. The methods evaluated the Monin-Obukhov stability length and the standard deviation of the hourly observed wind speed, so as to augment the latter quantity by F standard deviations. F is an optimized factor. A third method utilizing an optimized gust factor was also applied to the hourly wind. The latter procedure estimated 2952 peak winds with an rms error of 2.81 knots, an accuracy which was not surpassed by the other methods. Peak ground wind speed data were developed for use in space shuttle design operation analyses.

Graves, M. E.↗
NASA NTRS1974

Simulation of decelerating landing approaches on an externally blown flap STOL transport airplane

A fixed-base simulator program was conducted to define the problems and methods for solution associated with performing decelerating landing approaches on a representative STOL transport having a high wing and equipped with an external-flow jet flap in combination with four high-bypass-ratio fan-jet engines. Real-time digital simulation techniques were used. The computer was programed with equations of motion for six degrees of freedom and the aerodynamic inputs were based on measured wind-tunnel data. The pilot's task was to capture the localizer and the glide slope and to maintain them as closely as possible while decelerating from an initial airspeed of 140 knots to a final airspeed of 75 knots, while under IFR conditions.

Grantham, W. D.↗
NASA NTRS1974

Simulator study of minimum acceptable level of longitudinal stability for a representative STOL configuration during landing approach

A fixed-base simulator study was conducted to determine the minimum acceptable level of longitudinal stability for a representative turbofan STOL (short take-off and landing) transport airplane during the landing approach. Real-time digital simulation techniques were used. The computer was programed with equations of motion for six degrees of freedom, and the aerodynamic inputs were based on measured wind-tunnel data. The primary piloting task was an instrument approach to a breakout at a 60-m (200-ft) ceiling.

Grantham, W. D.↗
NASA NTRS1973

Comparison of ground and flight test results using a modified F106B aircraft

A F106 aircraft was modified by installing two additional underwing nacelles housing afterburning J85 engines to study exhaust nozzles in flight at Mach numbers up to 1.3. Installation effects were determined for several nozzles by comparing flight and wind-tunnel data. The effect is to decrease boattail drag and delay its drag rise Mach number to about 0.98. A study of Reynolds number effects, carried out at subsonic speeds with afterburning turbofan engines showed boattail drag to be sensitive to Reynolds number. In flight, drag was highest at the lowest Reynolds number, and decreased as the Re number was increased. Static and flyover noise measurements showed that, except for special cases, noise levels at takeoff (M = 0.4) were higher than predicted from static data.

Wilcox, F. A.↗
NASA NTRS1974

Evaluation of a new jet flap propulsive-lift system for turbofan-powered STOL transports

A large-scale STOL transport model with a new jet flap propulsive-lift system was subject to wind-tunnel testing. Aerodynamically, this IBF system combines the benefits of the jet flap and the mechanical flap with boundary layer control. Structurally, it creates its own spanwise air duct with the deflection of the mechanical flap. An additional short-chord control flap, located at the jet-flap exit, provides a powerful means for flight path and lateral controls. The results show that the overall effectiveness of this flap system compares well with other jet flap propulsive-lift systems. A preliminary study based on the wind-tunnel data was made on a medium-size IBF STOL jet transport configuration for a typical-military mission. This study showed that the IBF results in a configuration with a relatively low T/W ratio, making the system an attractive candidate for future designs.

Chin, Y. T.↗
NASA NTRS1974

The influence of surface waves on water circulation in a mid-Atlantic continental shelf region

The importance of wave-induced currents in different weather conditions and water depths (18.3 m and 36.6 m) is assessed in a mid-Atlantic continental-shelf region. A review of general circulation conditions is conducted. Factors which perturb the general circulation are examined using analytic techniques and limited experimental data. Actual wind and wave statistics for the region are examined. Relative magnitudes of the various currents are compared on a frequency of annual occurrence basis. Results indicated that wave-induced currents are often the same order of magnitude as other currents in the region and become more important at higher wind and wave conditions. Wind-wave and ocean-swell characteristics are among those parameters which must be monitored for the analytical computation of continental-shelf circulation.

Whitlock, C. H.↗
NASA NTRS1975

Moving-base visual simulation study of decoupled controls during approach and landing of a STOL transport aircraft

The simulation employed all six rigid-body degrees of freedom and incorporated aerodynamic characteristics based on wind-tunnel data. The flight instrumentation included a localizer and a flight director which was used to capture and to maintain a two-segment glide slope. A closed-circuit television display of a STOLport provided visual cues during simulations of the approach and landing. The decoupled longitudinal controls used constant prefilter and feedback gains to provide steady-state decoupling of flight-path angle, pitch angle, and forward velocity. The pilots were enthusiastic about the decoupled longitudinal controls and believed that the simulator motion was an aid in evaluating the decoupled controls, although a minimum turbulence level with root-mean-square gust intensity of 0.3 m/sec (1 ft/sec) was required to mask undesirable characteristics of the moving-base simulator.

Miller, G. K., Jr.↗
NASA NTRS1975

Phase change paint tests to investigate effects of TPS tiles on heating rates of the Rockwell space shuttle orbiter (test OH4C, model 21-0)

Information and data from wind tunnel tests conducted on 0.0175-scale models of the space shuttle orbiter are presented. The primary objective of the tests was to evaluate aerodynamic heating effects of the tiles in the thermal protection system (TPS). Tile gap depth and flow orientation effects on the TPS were investigated. Tile patterns were cut into the undersides of the orbiter models to simulate the gaps. One model was left smooth for comparison.

Quan, M.↗
NASA NTRS1975

Comparison of wind tunnel test results at free stream Mach 0.7 with results from the Boeing TEA-230 subsonic flow method

The use of the Boeing TEA-230 Subsonic Flow Analysis method as a primary design tool in the development of cruise overwing nacelle configurations is presented. Surface pressure characteristics at 0.7 Mach number were determined by the TEA-230 method for a selected overwing flow-through nacelle configuration. Results of this analysis show excellent overall agreement with corresponding wind tunnel data. Effects of the presence of the nacelle on the wing pressure field were predicted accurately by the theoretical method. Evidence is provided that differences between theoretical and experimental pressure distributions in the present study would not result in significant discrepancies in the nacelle lines or nacelle drag estimates.

Mohn, L. W.↗
NASA NTRS1975

Effects of spanwise blowing on the pressure field and vortex-lift characteristics of a 44 deg swept trapezoidal wing

Wind-tunnel data were obtained at a free-stream Mach number of 0.26 for a range of model angle of attack, jet thrust coefficient, and jet location. Results of this study show that the sectional effects to spanwise blowing are strongly dependent on angle of attack, jet thrust coefficient, and span location; the largest effects occur at the highest angles of attack and thrust coefficients and on the inboard portion of the wing. Full vortex lift was achieved at the inboard span station with a small blowing rate, but successively higher blowing rates were necessary to achieve full vortex lift at increased span distances. It is shown that spanwise blowing increases lift throughout the angle-of-attack range, delays wing stall to higher angles of attack, and improves the induced-drag polars. The leading-edge suction analogy can be used to estimate the section and total lifts resulting from spanwise blowing.

Campbell, J. F.↗
NASA NTRS1975

Inviscid supersonic/hypersonic body flowfields and aerodynamics from shock-capturing technique calculations

A shock-capturing, finite-difference computational procedure has been used to predict the body flowfields over a wide range of initial conditions, and these results have been compared with wind tunnel data. Two different studies have been performed. In the first, details of the shock layer surrounding space shuttle orbiter configurations have been calculated. In the second, the aerodynamic forces and moments on a parametrically varied set of blunt biconic bodies of revolution have been evaluated for angles of attack up to 20 degrees and Mach numbers from 5 to 20.

Chaussee, D. S.↗
NASA NTRS1975

Study to define unsteady flow fields and their statistical characteristics

Preliminary estimates of space shuttle fluctuating pressure environments were made based on analyses of wind tunnel data, and empirical prediction techniques. Particular emphasis was given to the external tank and solid rocket boosters for the transonic speed regime during launch of a parallel-burn space shuttle configuration. Predicted environments are presented as space-averaged zonal profiles with progressive shading from zone to zone to illustrate spatial variations in the magnitude of the fluctuating pressure coefficient over the surfaces of the external tank and solid rocket boosters. Predictions are provided for the transonic Mach number range from 0.8 equal to or less than M sub infinity equal to or less than 1.5, and for supersonic Mach numbers of 2.0 and 3.0.

Robertson, J. E.↗
NASA NTRS1975

Applications of Computer Graphics in Engineering

Various applications of interactive computer graphics to the following areas of science and engineering were described: design and analysis of structures, configuration geometry, animation, flutter analysis, design and manufacturing, aircraft design and integration, wind tunnel data analysis, architecture and construction, flight simulation, hydrodynamics, curve and surface fitting, gas turbine engine design, analysis, and manufacturing, packaging of printed circuit boards, spacecraft design.

Source record↗
NASA NTRS1976

Summary of flight tests to determine the spin and controllability characteristics of a remotely piloted, large-scale (3/8) fighter airplane model

An unpowered, large, dynamically scaled airplane model was test flown by remote pilot to investigate the stability and controllability of the configuration at high angles of attack. The configuration proved to be departure/spin resistant; however, spins were obtained by using techniques developed on a flight support simulator. Spin modes at high and medium high angles of attack were identified, and recovery techniques were investigated. A flight support simulation of the airplane model mechanized with low speed wind tunnel data over an angle of attack range of + or - 90 deg. and an angle of sideslip range of + or - 40 deg. provided insight into the effects of altitude, stability, aerodynamic damping, and the operation of the augmented flight control system on spins. Aerodynamic derivatives determined from flight maneuvers were used to correlate model controllability with two proposed departure/spin design criteria.

Holleman, E. C.↗
NASA NTRS1976

Results of tests in the AEDC VKF Tunnel B using the phase change paint technique on 0.04 scale 50 percent forebody models (82-0) of the Rockwell space shuttle orbiter (OH50A)

Model information and data from wind tunnel tests conducted on 0.04 scale 50 percent forebody models of the Space Shuttle Orbiter were presented. These tests were conducted using the phase change paint technique to determine aerodynamic heating rates due to various proturberances and recessions. Angles of attack from 20 deg through 45 deg were investigated at Mach 8.

Quan, M.↗
NASA NTRS1976

Unsteady aerodynamic flow field analysis of the space shuttle configuration. Part 4: 747/orbiter aeroelastic stability

A quasi-steady analysis of the aeroelastic stability of the lateral (antisymmetric) modes of the 747/orbiter vehicle was accomplished. The interference effect of the orbiter wake on the 747 tail furnishes an aerodynamic undamping contribution to the elastic modes. Likewise, the upstream influence of the 747 tail and aft fuselage on the orbiter beaver-tail rail fairing also is undamping. Fortunately these undamping effects cannot overpower the large damping contribution of the 747 tail and the modes are damped for the configurations analyzed. However, significant interference effects of the orbiter on the 747 tail have been observed in the pitch plane. The high response of the 747 vertical tail in the orbiter wave was also considered. Wind tunnel data points to flapping of the OMS pod wakes as the source of the wake resonance phenomenon.

Reding, J. P.↗
NASA NTRS1976

Utilization of the AEDC three-dimensional potential flow computer program

A potential flow computer program which has been in use for several years, was discussed. This program has been used primarily as a tool for flow-field analysis in support of test activities in transonic wind tunnels. Analyses have been made over a Mach number range from 0 to 0.9 for a variety of configurations from aircraft to wind tunnels, with excellent agreement between calculated flow fields and measured wind tunnel data. Analytical and experimental data for seven different flow analysis problems are presented in this paper.

Palko, R. L.↗
NASA NTRS1976

Development of an optimal automatic control law and filter algorithm for steep glideslope capture and glideslope tracking

A digital automatic control law to capture a steep glideslope and track the glideslope to a specified altitude is developed for the longitudinal/vertical dynamics of a CTOL aircraft using modern estimation and control techniques. The control law uses a constant gain Kalman filter to process guidance information from the microwave landing system, and acceleration from body mounted accelerometer data. The filter outputs navigation data and wind velocity estimates which are used in controlling the aircraft. Results from a digital simulation of the aircraft dynamics and the control law are presented for various wind conditions.

Halyo, N.↗