Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thrust”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,315 records · Page 73

Simulator evaluation of a perspective clipped-pole display and a thrust-vector controller for VTOL zero-zero landings

Five pilots participated in a simulator study to evaluate design features of a perspective clipped pole display and a side arm thrust vector controller for potential applications to VTOL zero visibility landings. Analyses of objective measures by a t test for related means showed significant learning effects, but did not show significant performance differences among display conditions. A mean longitudinal touchdown velocity of less than 4 knots, a mean vertical touchdown velocity of less than 1.22m/sec, and a mean longitudinal position error of approximately 15.24 m were attained during the final 10 trials of the experiment. The conclusion that adequate airspeed and altitude cues could be obtained from the glideslope and runway poles is supported by the absence of significant performance differences among display conditions.

Murphy, M. R.↗

Analysis of an all-metallic resilient pad gas-lubricated thrust bearing

A new type of resilient pad gas thrust bearing that does not contain any elastomers in the bearing assembly is described and analyzed. The bearing consists of sector-shaped pads mounted asymmetrically on resilient foil beams. The effects of bearing design parameters on performance are shown. Performance of a resilient pad bearing is compared with that of a pivoted pad bearing.

Anderson, W. J.↗

Nondestructive evaluation of electroformed outer shells for regeneratively cooled thrust chambers

Electroforming is presently a prime technique for producing the outer jackets of regeneratively cooled thrust chambers for rocket engines. Good bond integrity of the electroformed joints adjacent to the coolant passages is important to the useful service life of these aerospace systems. This investigation demonstrated that nondestructive evaluation techniques such as ultrasonic 'C' scan, holography, and acoustic emission are capable of detecting low integrity bonds which could lead to premature failures in the subject hardware.

Malone, G. A.↗

Statistical analysis of trim maneuvers in low thrust interplanetary navigation

An analytical technique for the statistical analysis of a low thrust trim maneuver in interplanetary navigation has been developed. The maneuver is treated rigorously as a nonlinear function of the trajectory errors to be removed, and the corresponding nongaussian statistics are developed. The method determines the statistical properties of the maneuver direction and duration, as well as the final state dispersion covariance. The analytical technique is applied to the terminal maneuver in a 1980 Encke slow flyby mission and is found to yield accurate statistical results with much less effort than Monte Carlo simulation. The method permits consideration of a shorter terminal maneuver than does linear analysis, with a consequent improvement in delivery accuracy.

Rinker, G. C.↗

Thrust vector control for the Space Shuttle Solid Rocket Motor

Thrust vector control (TVC) for the Space Shuttle Solid Rocket Motor (SRM) is obtained by omniaxis vectoring of the nozzle. The development and integration of the system are under the cognizance of Marshall Space Flight Center (MSFC). The nozzle and flexible bearing have been designed and will be built by Thiokol Corporation/Wasatch Division. The vector requirements of the system, the impact of multiple reuse on the components, and the unique problems associated with a large flexible bearing are discussed. The design details of each of the major TVC subcomponents are delineated. The subscale bearing development program and the overall development schedule also are presented.

Counter, D. N.↗

Flexible joints for thrust vector control

Flexible joints have been used to achieve thrust vector control over a wide range of sizes of nozzles and have been demonstrated successfully in bench tests and static firings, and are operational on two motors. From these many joints the problems of flexible joints have been defined as establishment of the movable nozzle envelope, definition of the actuation power requirements, definition of the mechanical properties of joint materials, adhesive bonding, test methods, and quality control. These data and problem solutions are contained in a large number of reports. Data relating to joint configuration, design requirements, materials selection, joint design, structural analysis, manufacture, and testing are summarized.

Woodberry, R. F. H.↗

Effects of upper-surface blowing and thrust vectoring on low-speed aerodynamic characteristics of a large-scale supersonic transport model

Tests were conducted in the Langley full-scale tunnel to determine the low-speed aerodynamic characteristics of a large-scale arrow-wing supersonic transport configured with engines mounted above the wing for upper surface blowing, and conventional lower surface engines with provisions for thrust vectoring. A limited number of tests were conducted for the upper surface engine configuration in the high lift condition for beta = 10 in order to evaluate lateral directional characteristics, and with the right engine inoperative to evaluate the engine out condition.

Coe, P. L., Jr.↗

Thrust and wing loading requirements for short haul aircraft constrained by engine noise and field length

Propulsion system and wing loading requirements are determined for a mechanical flap and an externally blown flap aircraft for various engine noise levels and two engine cycles. Both aircraft are sized to operate from a 914m (3000 ft) runway and perform the same mission. For each aircraft concept, propulsion system sizing is demonstrated for two different engine cycles - one having a fan pressure ratio of 1.5 and a bypass ratio of 9, and the other having a fan pressure ratio of 1.25 and a bypass ratio of 17.8. The results presented include the required thrust-to-weight ratio, wing loading, resulting gross weight, and direct operating costs, as functions of the engine noise level, for each combination of engine cycle and aircraft concept.

Bowles, J. V.↗

Longitudinal aerodynamic characteristics of a deflected-thrust propulsive-lift transport model

A wind-tunnel investigation was conducted to determine the effect of deflecting the engine exit of a four-engine double-slotted flap transport to provide STOL performance. Longitudinal aerodynamic data were obtained at various engine exit positions and deflections. The data were obtained at three flap deflections representing cruise, take-off, and landing conditions for a range of angles of attack and various thrust coefficients. Downwash angles at the location of the horizontal tail were measured. The data are presented without analysis or discussion. Photographs of the test configurations are shown.

Hoad, D. R.↗

Design and evaluation of a 3 million DN series-hybrid thrust bearing

The bearing, consisting of a 150-mm ball bearing and a centrifugally actuated, conical, fluid-film bearing, was fatigue tested. Test conditions were representative of a mainshaft ball bearing in a gas turbine engine operating at maximum thrust load to simulate aircraft takeoff conditions. Tests were conducted up to 16000 rpm and at this speed an axial load of 15568 newtons (3500 lb) was safely supported by the hybrid bearing system. Through the series-hybrid bearing principle, the effective ball bearing speed was reduced to approximately one-half of the shaft speed. It was concluded that a speed reduction of this magnitude results in a ten-fold increase in the ball bearing fatigue life. A successful evaluation of fluid-film bearing lubricant supply failure was performed repeatedly at an operating speed of 10,000 rpm. A complete and smooth changeover to full-scale ball bearing operation was effected when the oil supply to the fluid-film bearing was cut off. Reactivation of the fluid-film oil supply system resulted in a flawless return to the original mode of hybrid operation.

Scibbe, H. W.↗

Analysis and design of a cantilever-mounted resilient-pad gas-lubricated thrust bearing

A thrust bearing consisting of pads mounted on resilient, metallic, cantilever beams is described and analyzed. Compliance and stiffness of the bearing assembly are discussed, and the effects of bearing design parameters on performance are shown. After the general analysis, a design example is presented for a flat sector-shaped gas bearing. A special case where zero axial movement of the runner can be obtained is pointed out.

Etsion, I.↗

Amplitude effects on the dynamic performance of a hydrostatic gas thrust bearing

The Reynolds' equation is applied to a strip gas thrust bearing to analyze amplitude disturbance effects on its dynamic performance. The Reynolds' equation is numerically approximated using finite difference techniques. The time dependent load carrying capacity is represented by a Fourier series up to and including the third harmonics. Design curves for the load capacity and the linear stiffness and damping are presented as a function of inlet location, restrictor coefficient, supply pressure, amplitude of oscillation, and squeeze number. For the range of amplitudes investigated the dimensionless load capacity, stiffness and damping does not exhibit an appreciable change in magnitude; thus, only one design curve is needed to represent each relationship. A design methodology is presented.

Stiffler, A. K.↗

Dynamic control of SRB thrust tailoff for separation

The use of the difference in chamber pressure between solid rocket booster engines as a controlling signal to the flight control system during booster thrust tailoff was examined. In addition, the control capability of the Generalized Attitude Control System (GACS) was compared to that of the baseline. Results indicate that the difference in chamber pressure signal provided essentially no improvement. However, the GACS is considerably better than the baseline in controlling during tailoff disturbances.

Webb, W. W.↗

Estimation of unmodeled forces on a low-thrust space vehicle

The application of a sequential estimation algorithm, which compensates for random errors in the dynamic model, to the problem of estimating the state of a continuously thrusting solar electric propulsion space vehicle is investigated. The dynamic model errors, due to random anomalies in the propulsion system, are approximated successfully by both first order and second order Gauss-Markov processes to obtain a more accurate and stable orbit determination algorithm. The importance of correct dynamic and measurement modeling in achieving accurate estimates is demonstrated.

Tapley, B. D.↗

Noncatalytic hydrazine thruster development - 0.050 to 5.0 pounds thrust

Noncatalytic (thermal-decompositon) hydrazine thrusters can operate in both the pulsing and steady-state modes to meet the propulsive requirements of long-life spacecraft. The thermal decomposition mode yields higher specific impulse than is characteristic of catalytic thrusters at similar thrust levels. This performance gain is the result of higher temperature operation and a lower fraction of ammonia dissociation. Some life limiting factors of catalytic thrusters are eliminated.

Murch, C. K.↗

Design and evaluation of a 3 million DN series-hybrid thrust bearing

The design and experimental evaluation of a series-hybrid thrust bearing, consisting of a 150-mm ball bearing and a centrifugally actuated, conical, fluid-film bearing, is presented. Tests were conducted up to 16,000 rpm and at this speed an axial load of 15,600 N (3500 lb) was safely supported by the hybrid bearing system. Through the series-hybrid bearing principle, the effective ball bearing speed was reduced to approximately one-half of the shaft speed. A speed reduction of this magnitude would result in a tenfold increase in the ball bearing fatigue life. A successful evaluation of fluid-film bearing lubricant supply failure was performed repeatedly at an operating speed of 10,000 rpm. A complete and smooth changeover to full-scale ball bearing operation was effected when the oil supply to the fluid-film bearing was cut off. Reactivation of the fluid-film oil supply system produced a flawless return to the original mode of hybrid operation.

Scibbe, H. W.↗

A thrust-sheet propulsion concept using fissionable elements

A space propulsion concept is proposed and analyzed which consists of a thin sheet coated on one side with fissionable material, so that nuclear power is converted directly into propulsive power. Thrust is available both from ejected fission fragments and from thermal radiation. Optimum thicknesses are determined for the active and substrate layers. This concept is shown to have potential mission capability (in terms of velocity increments) superior to that of all other advanced propulsion concepts for which performance estimates are available. A suitable spontaneously fissioning material such as Cf254 could provide an extremely high-performance first stage beyond earth orbit. In contrast with some other advanced nuclear propulsion concepts, there is no minimum size below which this concept is infeasible.

Moeckel, W. E.↗

Effects of upper-surface blowing and thrust vectoring on low speed aerodynamic characteristics of a large-scale supersonic transport model

Tests were conducted in a full scale tunnel to determine the low speed aerodynamic characteristics of a large scale arrow wing supersonic transport configured with engines mounted above the wing for upper surface blowing and conventional lower surface engines having provisions for thrust vectoring. Tests were conducted over an angle of attack range of -10 deg to 34 deg and for Reynolds numbers (based on the mean aerodynamic chord) of 5.17 x 1 million and 3.89 x 1 million. A limited number of tests were also conducted for the upper surface engine configuration in the high lift condition at an angle of sideslip of 10 deg in order to evaluate lateral directional characteristics and with the right engine inoperative in order to evaluate the engine out condition.

Coe, P. L., Jr.↗