Results for “software differences” — Page 73

NASA NTRS2005

Foreign Object Damage Identification in Turbine Engines

This report summarizes the collective work of a five-person team from different organizations examining the problem of detecting foreign object damage (FOD) events in turbofan engines from gas path thermodynamic and bearing accelerometer sensors, and determining the severity of damage to each component (diagnosis). Several detection and diagnostic approaches were investigated and a software tool (FODID) was developed to assist researchers detect/diagnose FOD events. These approaches include (1) fan efficiency deviation computed from upstream and downstream temperature/ pressure measurements, (2) gas path weighted least squares estimation of component health parameter deficiencies, (3) Kalman filter estimation of component health parameters, and (4) use of structural vibration signal processing to detect both large and small FOD events. The last three of these approaches require a significant amount of computation in conjunction with a physics-based analytic model of the underlying phenomenon the NPSS thermodynamic cycle code for approaches 1 to 3 and the DyRoBeS reduced-order rotor dynamics code for approach 4. A potential application of the FODID software tool, in addition to its detection/diagnosis role, is using its sensitivity results to help identify the best types of sensors and their optimum locations within the gas path, and similarly for bearing accelerometers.

Strack, William↗

NASA NTRS2005

Beyond the Prototype: The Design Evolution of a Deployed AI System

Our previous experiences with deployed intelligent control agents for NASA advanced life support systems (Schreckenghost et al., 2002) inspired us to develop the Distributed Collaboration and Interaction (DCI) system to help humans and mostly-autonomous software agents work together. We discovered many unaddressed needs for human interaction with control agents that operate continuously over months to years to monitor and perform process control for regenerative life support systems. These systems recover usable water or air from the waste products created by biological systems over time. Through the DCI project, we have addressed the needs for interaction between humans and autonomous control systems. This paper describes the software engineering aspects of our experiences, first, in designing and developing a prototype of the DCI system, and later, in adjusting the implementation to make the leap from initial prototype to a system ready to be applied under varying circumstances to meet different needs. The details in the paper focus primarily on the second stage of development. The DCI system is currently deployed, operating 24/7, to assist humans to interact with an advanced Water Recovery System (WRS). In addition, we have demonstrated an application of DCI to support ground personnel in mission support roles.

Martin, C.↗

NASA NTRS2004

Beyond the Prototype: The Design Evolution of a Deployed AI System

Our previous experiences with deployed intelligent control agents for NASA advanced life support systems (Schreckenghost et al., 2002) inspired us to develop the Distributed Collaboration and Interaction (DCI) system to help humans and mostly-autonomous software agents work together. We discovered many unaddressed needs for human interaction with control agents that operate continuously over months to years to monitor and perform process control for regenerative life support systems. These systems recover usable water or air from the waste products created by biological systems over time. Through the DCI project, we have addressed the needs for interaction between humans and autonomous control systems. This paper describes the software engineering aspects of our experiences, first, in designing and developing a prototype of the DCI system, and later, in adjusting the implementation to make the leap from initial prototype to a system ready to be applied under varying circumstances to meet different needs. The details in the paper focus primarily on the second stage of development. The DCI system is currently deployed, operating 24/7, to assist humans to interact with an advanced Water Recovery System (WRS). In addition, we have demonstrated an application of DCI to support ground personnel in mission support roles.

Martin, Cheryl↗

NASA NTRS2009

Lossless Compression of Data into Fixed-Length Packets

A computer program effects lossless compression of data samples from a one-dimensional source into fixed-length data packets. The software makes use of adaptive prediction: it exploits the data structure in such a way as to increase the efficiency of compression beyond that otherwise achievable. Adaptive linear filtering is used to predict each sample value based on past sample values. The difference between predicted and actual sample values is encoded using a Golomb code.

Kiely, Aaron B.↗

NASA NTRS2018

Standardizing GPU Radiation Test Approaches

While some Graphical Processing Units (GPUs) are discrete components (i.e.GTX1050), others take the form of an IP block or embedded engine within a System on Chip (SoC) device such as the Qualcomm Snapdragon"TM" 820 which contains a Qualcomm Adreno"TM" 530 GPU. Within this device are various functional blocks which can be exercised with software payloads. NVidia's Jetson"TM" TX1 SoC is provided on a System on Module (SOM). Within it are Central Processing Unit (CPU) cores and an nVidia GPU which can be accessed similarly to a discrete GPU coprocessor. While the packaging is different, each one of these GPUs needs to be tested using the same standardized code.

Single Event Effects (SEE)↗

NASA NTRSDate not supplied

Optimization of a Solver for Computational Materials and Structures Problems on NVIDIA Volta and AMD Instinct GPUs

The Scalable Implementation of Finite Elements by NASA (ScIFEN) is a software package developed to solve complex computational materials and structures problems using the finite element method (FEM). In this paper, we describe optimization techniques to speed up the linear solver computation that occurs within the ScIFEN application. We consider GPUs from two different vendors, NVIDIA and AMD as our target platforms for optimization and highlight differences in performance and optimization techniques. The NVIDIA GPU Volta V100 is used in the Summit system deployed at Oak Ridge National Laboratory, and the new exascale system, Frontier, will be using AMD Radeon Instinct GPU. We evaluated the performance of various optimization techniques on test matrices, ranging in size from100K to 4M, that are representative of ScIFEN applications. The linear solver computation is memory-bound on both GPUs. Our experiments show that on the NVIDIA GPU we obtained up to79%of the theoretical peak bandwidth, while the AMD GPU achieved 59%. Overall, the NVIDIA V100 GPU outperforms the AMD MI 25 GPU1. We observed an overall speedup of up to37X on an NVIDIA V100 compared to an Intel Skylake 12-coremachine. The solver for a 4M degree of freedom system took under 2.5 seconds.

Mohammad Zubair↗

NASA NTRSDate not supplied

Pragmatic Stress Prediction on Additively Manufactured Coupons

Prediction of residual stresses from process parameters for additively manufactured large metal parts is computationally expensive. NASA is currently developing meter-scale parts with direct energy deposition. Practically, the predictive computational methods need to efficiently scale-up to meter-scale parts. Coupled thermal-mechanical multi-physics simulations have been developed with the pragmatic method using ABAQUS, COMSOL Multiphysics, ALE3D software. The residual stresses are a result of the manufacturing process which creates thermal cycling of the build layers. The pragmatic method uses lumped thermal layers for stress predictions to reduce computational costs. The stress predictions as well as deformations of the different codes are compared with each other and with ANSYS Additive using identical material models, boundary and initial conditions. The codes were used to simulate three different geometries: a thin wall, hollow cylinder and twin-cantilever part. The coupon parts were then manufactured with Inconel-625. The residual stresses in these parts were measured using X-ray diffraction as well as neutron beam diffraction at NIST. The stress measurements for the two technologies are compared. The pragmatic stress prediction method enabled predictions of the multi-centimeter scale parts using desktop computer workstations in only a few hours for each coupon. The results of the simulated stress predictions compared favorably with the measured stresses even though thermally lumped layers were employed. Finally, a two-meter scale nozzle was simulated using ANSYS Additive. The simulations were used to examine the build orientation trade-space with respect to resulting geometric deformation. The predicted deformations were compared to measurements of an actual subscale part manufactured with direct energy deposition.

Additive Manufacturing↗

NASA NTRSDate not supplied

Pragmatic Stress Prediction on Additively Manufactured Coupons

Prediction of residual stresses from process parameters for additively manufactured large metal parts is computationally expensive. NASA is currently developing meter-scale parts with direct energy deposition. Practically, the predictive computational methods need to efficiently scale-up to meter-scale parts. Coupled thermal-mechanical multi-physics simulations have been developed with the pragmatic method using ABAQUS, COMSOL Multiphysics, ALE3D software. The residual stresses are a result of the manufacturing process which creates thermal cycling of the build layers. The pragmatic method uses lumped thermal layers for stress predictions to reduce computational costs. The stress predictions as well as deformations of the different codes are compared with each other and with ANSYS Additive using identical material models, boundary and initial conditions. The codes were used to simulate three different geometries: a thin wall, hollow cylinder and twin-cantilever part. The coupon parts were then manufactured with Inconel-625. The residual stresses in these parts were measured using X-ray diffraction as well as neutron beam diffraction at NIST. The stress measurements for the two technologies are compared. The pragmatic stress prediction method enabled predictions of the multi-centimeter scale parts using desktop computer workstations in only a few hours for each coupon. The results of the simulated stress predictions compared favorably with the measured stresses even though thermally lumped layers were employed. Finally, a two-meter scale nozzle was simulated using ANSYS Additive. The simulations were used to examine the build orientation trade-space with respect to resulting geometric deformation. The predicted deformations were compared to measurements of an actual subscale part manufactured with direct energy deposition.

pragmatic method↗

NASA NTRSDate not supplied

The Path to Crew Autonomy - Situational Awareness in Scheduling and Rescheduling Tasks for Novice Schedulers

To increase crew autonomy for long duration exploration-class missions (LDEM), certain mission support tasks need to be completed by crew. Currently, crew activities are scheduled over the course of several weeks by ground-based experts with years of experience-based training. These experts display extensive amounts of situational awareness (SA) throughout task execution by maintaining a mental model of additional factors during scheduling such as constraints (e.g. physical space/layout), abilities and skills of the crew, and crew preferences allowing them to anticipate and mitigate potential issues. Thus, situational awareness is a key component for crews to manage their own schedules. In this paper, we examined situational awareness in novice schedulers in both a scheduling and rescheduling task. Our findings indicate that there is no significant difference between scheduling and rescheduling tasks for the development of SA in novice schedulers. Additionally, our experiment shows that novice schedulers are less able to develop sufficient SA for constraints that are dependent on one or more activities. Thus, we propose that software aids may be useful to support novice schedulers and increase SA in scheduling/rescheduling tasks. This work is vital to ensure the successful transfer of mission support tasks to the crew for future LDEM.

situation awareness↗

NASA NTRS2011

Kinematics and Kinetics of Squat and Deadlift Exercises with Varying Stance Widths

The primary motion of squat and deadlift exercise involves flexion and extension of the hips, knees, and ankles, but each exercise can be performed with variations in stance width. These variations may result in differing kinematics and ground reaction forces (GRF), which may in turn affect joint loading. PURPOSE: The purpose of this investigation was to compare ankle, knee, and hip kinematics and kinetics of normal squat (NS), wide-stance squat (WS), normal deadlift (ND), and sumo deadlift (SD). We hypothesized that hip joint kinematics and work at each joint would differ between exercise variations. METHODS: Six subjects (3 m/3 f; 70.0 plus or minus 13.7 kg; 168 plus or minus 9.9 cm) performed each lift in normal gravity on the ground-based version of the Advanced Resistive Exercise Device (ARED) used on the International Space Station. The ARED provided resistance with a combination vacuum tube/flywheel mechanism designed to replicate the gravitational and inertial forces of free weights. Subjects completed each lift with their 10-repetition maximum load. Kinematic data were collected at 250 Hz by a 12-camera motion-capture system (Smart-D, BTS Bioengineering, Milan, Italy), and GRF data were collected at 1000 Hz with independent force platforms for each leg (Model 9261, Kistler Instruments AG, Winterhur, Switzerland). All data were captured simultaneously on a single workstation. The right leg of a single lift for each motion was analyzed. Modeling software (OpenSim 2.2.0, Simbios, Palo Alto, CA) determined joint kinematics and net positive and negative work at each lower extremity joint. Total work was found as the sum of work across all joints and was normalized by system mass. Effect sizes and their 95% confidence intervals were computed between conditions. RESULTS: Peak GRF were similar for each lift. There were no differences between conditions in hip flexion range of motion (ROM). For hip adduction ROM, there were no differences between the NS, WS, and SD. However, hip adduction ROM was greater during the NS and SD than during the ND. Hip rotation ROM was greater during the WS than during the NS and SD, and was greater during the SD than during the ND. For knee and ankle flexion ROM, the ND, WS, and SD were not different, but ROM was greater during the NS than the ND and greater during the WS than the SD. Total eccentric work was greater during the WS than the SD. Otherwise, there were no differences in eccentric or concentric work between conditions. CONCLUSIONS: Although squat and deadlift exercises consist of similar motions, there are kinematic differences between them that depend on stance width. Total eccentric and concentric work are similar for different lifts, but differing kinematics may require activation of different musculature for each variation. With respect to each condition, in the ND the ROM of each joint tended to be less, and the WS tended to trade knee motion for hip motion. PRACTICAL APPLICATIONS: Knowledge of differences in kinematics and kinetics between different squat and deadlift variations is important for coaches and rehabilitation personnel to understand when prescribing exercise. Our results suggest that each variation of the squat and deadlift should be considered a separate exercise that may induce different long-term training effects.

DeWitt, John K.↗

NASA NTRS2011

MicroShell Minimalist Shell for Xilinx Microprocessors

MicroShell is a lightweight shell environment for engineers and software developers working with embedded microprocessors in Xilinx FPGAs. (MicroShell has also been successfully ported to run on ARM Cortex-M1 microprocessors in Actel ProASIC3 FPGAs, but without project-integration support.) Micro Shell decreases the time spent performing initial tests of field-programmable gate array (FPGA) designs, simplifies running customizable one-time-only experiments, and provides a familiar-feeling command-line interface. The program comes with a collection of useful functions and enables the designer to add an unlimited number of custom commands, which are callable from the command-line. The commands are parameterizable (using the C-based command-line parameter idiom), so the designer can use one function to exercise hardware with different values. Also, since many hardware peripherals instantiated in FPGAs have reasonably simple register-mapped I/O interfaces, the engineer can edit and view hardware parameter settings at any time without stopping the processor. MicroShell comes with a set of support scripts that interface seamlessly with Xilinx's EDK tool. Adding an instance of MicroShell to a project is as simple as marking a check box in a library configuration dialog box and specifying a software project directory. The support scripts then examine the hardware design, build design-specific functions, conditionally include processor-specific functions, and complete the compilation process. For code-size constrained designs, most of the stock functionality can be excluded from the compiled library. When all of the configurable options are removed from the binary, MicroShell has an unoptimized memory footprint of about 4.8 kB and a size-optimized footprint of about 2.3 kB. Since MicroShell allows unfettered access to all processor-accessible memory locations, it is possible to perform live patching on a running system. This can be useful, for instance, if a bug is discovered in a routine but the system cannot be rebooted: Shell allows a skilled operator to directly edit the binary executable in memory. With some forethought, MicroShell code can be located in a different memory location from custom code, permitting the custom functionality to be overwritten at any time without stopping the controlling shell.

Werne, Thomas A.↗

NASA NTRS1983

User alternatives in post-processing for raster-to-vector conversion

A number of Landsat-based coniferous forest stratum maps have been created of the Eldorado National Forest in California. These maps were produced in raster image format which is not directly usable by the U.S. Forest Service's vector-based Wildland Resource Information System (WRIS). As a solution, raster-to-vector conversion software has been developed for processing classified images into polygonal data structures. Before conversion, however, the digital classification images must be simplified to remove high spatial variance ('noise', 'speckle') and meet a USFS ten acre minimum requirement. A post-processing (simplification) strategy different from those commonly used in raster image processing may be desired for preparing maps for conversion to vector format, because simplification routines typically permit diagonal connections in the process of reclassifying pixels and forming new polygons. Diagonal connections are often undesirable when converting to vector format because they permit polygons to effectively cross over each other and occupy a common location. Three alternative methodologies are discussed for simplifying raster data for conversion to vector format.

Logan, T. L.↗

NASA NTRS1989

NCTM workshop splinter session, IR thermal measurement instruments

The splinter session dealing with commercial industrial thermal measurement state-of-the-hardware had a total attendance of 15. Two papers were presented in the splinter session as follows: (1) Development of an Infrared Imaging System for the Surface Tension Driven Convection Experiment, Alexander D. Pline, NASA LeRC; (2) A Space-qualified PtSi Thermal Imaging System, Robert W. Astheimer, Barnes Engineering Div., EDO Corp. In addition a brief description of SPRITE detector technology was presented by Richard F. Leftwich of Magnovox. As anticipated, the discussions were concerned mainly with thermal imaging figures of merit rather than those for point measurement instruments. The need for uniform guidelines whereby infrared thermal imaging instruments could be specified and evaluated was identified as most important, particularly where temperature measurements are required. Presently there are differences in the way different manufacturers present significant performance parameters in their instrument data sheets. Furthermore, the prospective user has difficulty relating these parameters to actual measurement needs, and procedures by which performance can be verified are poorly defined. The current availability of powerful thermal imaging diagnostic software was discussed.

Kaplan, Herbert↗

NASA NTRS1991

Issues associated with establishing control zones for international space operations

Cooperative missions in Earth orbit can be facilitated by developing a strategy to regulate the manner in which vehicles interact in orbit. One means of implementing such a strategy is to utilize a control zones technique that assigns different types of orbital operations to specific regions of space surrounding a vehicle. Considered here are issues associated with developing a control zones technique to regulate the interactions of spacecraft in proximity to a manned vehicle. Technical and planning issues, flight hardware and software issues, mission management parameter, and other constraints are discussed. Also covered are manned and unmanned vehicle operations, and manual versus automated flight control. A review of the strategies utilized by the Apollo Soyuz Test Project and the Space Station Freedom Program is also presented.

Nader, Blair A.↗

NASA NTRS1992

Issues in developing control zones for international space operations

Cooperative missions in earth orbit can be facilitated by developing a strategy to regulate the manner in which vehicles interact in orbit. One means of implementing such a strategy is to utilize a control zones technique that assigns different types of orbital operations to specific regions of space surrounding a vehicle. Considered here are issues associated with developing a control zones technique to regulate the interactions of spacecraft in proximity to a manned vehicle. Technical and planning issues, flight hardware and software issues, mission management parameter, and other constraints are discussed. Also covered are manned and unmanned vehicle operations, and manual versus automated flight control. A review of the strategies utilized by the Apollo Soyuz Test Project and the Space Station Freedom Program is also presented.

Nader, Blair A.↗

NASA NTRS1996

Micromechanics Analysis Code (MAC). User Guide: Version 2.0

The ability to accurately predict the thermomechanical deformation response of advanced composite materials continues to play an important role in the development of these strategic materials. Analytical models that predict the effective behavior of composites are used not only by engineers performing structural analysis of large-scale composite components but also by material scientists in developing new material systems. For an analytical model to fulfill these two distinct functions it must be based on a micromechanics approach which utilizes physically based deformation and life constitutive models and allows one to generate the average (macro) response of a composite material given the properties of the individual constituents and their geometric arrangement. Here the user guide for the recently developed, computationally efficient and comprehensive micromechanics analysis code's (MAC) who's predictive capability rests entirely upon the fully analytical generalized method of cells (GMC), micromechanics model is described. MAC is a versatile form of research software that 'drives' the double or triply periodic micromechanics constitutive models based upon GMC. MAC enhances the basic capabilities of GMC by providing a modular framework wherein (1) various thermal, mechanical (stress or strain control) and thermomechanical load histories can be imposed, (2) different integration algorithms may be selected, (3) a variety of constituent constitutive models may be utilized and/or implemented, and (4) a variety of fiber and laminate architectures may be easily accessed through their corresponding representative volume elements.

Wilt, T. E.↗

NASA NTRS1999

Micromechanics Analysis Code With Generalized Method of Cells (MAC/GMC): User Guide

The ability to accurately predict the thermomechanical deformation response of advanced composite materials continues to play an important role in the development of these strategic materials. Analytical models that predict the effective behavior of composites are used not only by engineers performing structural analysis of large-scale composite components but also by material scientists in developing new material systems. For an analytical model to fulfill these two distinct functions it must be based on a micromechanics approach which utilizes physically based deformation and life constitutive models and allows one to generate the average (macro) response of a composite material given the properties of the individual constituents and their geometric arrangement. Here the user guide for the recently developed, computationally efficient and comprehensive micromechanics analysis code, MAC, who's predictive capability rests entirely upon the fully analytical generalized method of cells, GMC, micromechanics model is described. MAC/ GMC is a versatile form of research software that "drives" the double or triply periodic micromechanics constitutive models based upon GMC. MAC/GMC enhances the basic capabilities of GMC by providing a modular framework wherein 1) various thermal, mechanical (stress or strain control) and thermomechanical load histories can be imposed, 2) different integration algorithms may be selected, 3) a variety of material constitutive models (both deformation and life) may be utilized and/or implemented, and 4) a variety of fiber architectures (both unidirectional, laminate and woven) may be easily accessed through their corresponding representative volume elements contained within the supplied library of RVEs or input directly by the user, and 5) graphical post processing of the macro and/or micro field quantities is made available.

Arnold, S. M.↗

NASA NTRS2001

Experimental and Computational Studies of the Control of Convection of Non-Conducting Liquids During solidification by Means of a Magnetic Field Gradient

The elimination of convection is essential in experimental investigations of diffusive transport (of heat and matter) during solidification. One classical approach to damping convection in a conducting liquid is the application of a magnetic field. The damping phenomenon is the induction, by the motion of a conductor in a magnetic field, of currents which interact with the field to produce Lorentz forces that oppose the flow. However, there are many liquids which are not sufficiently conducting to exploit this phenomenon; examples include the transparent liquids (such as succinonitrile-acetone) that are used as "model alloys" in fundamental solidification studies. There have been several investigations of the solidification of these liquids that have been carried out in orbiting laboratories to eliminate natural convection. The paper describes an investigation of an alternative approach whereby a magnetic field gradient is applied to the liquid. A magnetic body force then arises which is dependent on the susceptibility of the liquid and thereby on the temperature and or concentration. With the field gradient aligned vertically and of correct magnitude, the variation of gravitational body force due to temperature/concentration dependent density can be counterbalanced by a variation in magnetic body force. Experiments have been carried out in a super-conducting magnet at Marshall Space Flight Center to measure velocities in an aqueous manganese chloride solution. The solution was contained in a chamber with temperature controlled end walls and glass side walls. Velocities were measured by particle image velocimetry. Starting from zero current in the magnet (zero field gradient) flow driven by the temperature difference between the end walls was measured. At a critical current the flow was halted. At higher currents the normal convection was reversed. The experiments included ones where the solution was solidified and were accompanied by solution of the flow/transport equations using the software package FLUENT.

Seybert, C. D.↗