SEARCH · Engineering Papers

Results for “slots”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,315 records · Page 73

All sources NASA NTRS DOE OSTI

NASA NTRS1973

Cryogenic gyroscope housing

A cryogenic gyroscope housing having gas spin-up means provided in annular discs inserted between housing shells is described. A circumferential recess in the inner edges of the discs at their juncture serves as the gas spin-up channel, and recesses in the discs at their junctures with the shells form suction channels. The discs also have inlet and outlet ports communicating with the spin-up channel and exhaust slots communicating with the suction channels. Mating surfaces of the discs and housing shells are held in position by optical contact at the equational plane of the housing. Suspension electrodes and thin-film readout loops are disposed in shells. A centering band and clamp rings provide for proper alinement and placement of parts in formation of optical contact joints.

Angele, W.↗

NASA NTRS1974

Optical measurement of static temperature and hydroxyl radical profiles in a hydrogen-fueled supersonic combustor

Profiles of static temperature and hydroxyl radical concentration were measured in a two-dimensional supersonic combustor test section 22.8 cm downstream of hydrogen injection. A high-pressure gas generator supplied vitiated air to the test section at Mach 2.44, atmospheric pressure, and a total temperature of about 2240 K. Room-temperature hydrogen was injected through a 0.40-cm step slot at Mach 1 and matched pressure. The measurements utilized a noninterfering spectral line absorption technique in which narrow ultraviolet emission lines of the hydroxyl electronic transition are absorbed by the broader absorption lines in the combustion gas. Comparison of the measured temperature profiles with theoretical calculations showed good agreement.

Gaugler, R. E.↗

NASA NTRS1974

Wind tunnel investigation of a large-scale semispan model with an unswept wing and an upper-surface blown jet flat

An investigation of the static longitudinal aerodynamic characteristics of a large-scale semispan model with an unswept wing and an upper-surface blown jet flap for lift augmentation was conducted in the Langley full-scale tunnel. The wing had an aspect ratio of 7.8 (3.9 for the semispan) and a simulated turbofan engine mounted ahead of and above the wing in a nacelle with a rectangular-exit nozzle. The flap system had three spanwise flap segments: (1) an inboard plain flap located behind the engine and having a large radius of curvature to provide a smooth upper surface to enhance the turning of the jet sheet, (2) a double-slotted midspan flap, and (3) a drooped aileron equipped with blowing boundary-layer control. The wing was also equipped with a full-span leading-edge Krueger flap with blowing boundary-layer control. In addition to the aerodynamic measurements, noise measurements were also included in the investigation for positions above and below the wing.

Smith, C. C., Jr.↗

NASA NTRS1974

Effect of geometrical and flow parameters on high-effectiveness region of film cooling

Previous analyses for an inviscid jet injected into a stream and the turbulent mixing region which forms between jet and stream are used to find the extent of the core region in a cooling film by calculating the growth of the turbulent boundary layer on the downstream wall. The core is a region of nearly perfect effectiveness which ends at the intersection of the boundary layer and the mixing region. The calculations show that the most important geometrical factor bearing on the length of the core is the curvature of the wall. When the radius of curvature is large, the boundary layer remains thin and the core is long. The effects of Reynolds number, total-pressure difference between film and stream, and lateral position of the downstream wall are also investigated. The step configuration is shown to have a longer core than the slot for the same flow conditions.

Braum, W. H.↗

NASA NTRS1974

Acoustic loads on an externally blown flap system due to impingement of a TF-34 jet engine exhaust

One of the powered lift systems currently being considered for use on STOL vehicles obtains additional lift by impinging the flow of a jet exhaust on the flaps and turning it downward. This direct impingement subjects large areas of the flap to the fluctuating pressure loads of the turbulent jet flow; these loads have the potential for causing high vibration levels and sonic fatigue failures. A test was conducted on a full-scale mockup of an externally blown flap system, which consisted of a TF-34 engine and a section of a wing having a triple-slotted flap. Data were obtained and evaluated on the fluctuating pressures on the flaps and it is the purpose of this paper to present some of the results describing the loads.

Schoenster, J. A.↗

NASA NTRS1972

A Structural Design for an Externally Blown Flap (EBF) Medium STOL Research Aircraft

A computer program to predict, by reference to structural drawings, the dynamic response of a high lift STOL wing with externally blown flaps was developed. Structural data for the computer program are presented in the form of sketches, weight and dynamic loads information graphs, and tables for an external blown, triple-slotted flap, high lift STOL transport wing. Weight, mass distribution, and moment of inertia data are summarized in table form and presented pictorially by drawing layout. The methods used for obtaining weight data were: (1) actual know, weight of components, (2) preliminary stress sizing, and (3) statistical weight estimating methods.

Source record↗

NASA NTRS1974

Use of multiple discrete wall jets for delaying boundary layer separation

The effectiveness of a spanwise array of small discrete blowing nozzles in preventing separation of a turbulent boundary layer was investigated experimentally. The spacing, axial location, and momentum flux of the nozzles were varied in a systematic way, and overall performance was measured for each combination. Extensive mean velocity profiles were measured for one selected combination. Overall diffusion achieved before separation was correlated successfully with a momentum flux excess parameter, and in terms of this parameter discrete nozzles, when advantageously placed, were found to perform somewhat better than an optimally placed two-dimensional jet slot.

Mclean, J. D.↗

NASA NTRS1974

Computer analysis of aircraft and shuttle antennas

Progress on predicting the patterns of high-frequency antennas on aircraft and shuttles is reported. Patterns are presented for an axial slot antenna on a circular cylinder partially coated with a dielectric layer. Results are shown for Omega signal disturbance by a conducting vertical pole.

Burnside, W. D.↗

NASA NTRS1974

Parametric study of relaminarization of turbulent boundary layers on nozzle walls

By means of comparisons between theoretical predictions and experimental data, the accuracy of a boundary procedure to predict the effect of large streamwise accelerations upon initially turbulent boundary layers is assessed. The boundary layer procedure is based upon simultaneous solution of the boundary layer partial differential equations and the integral turbulence kinetic energy equation. The results of the present investigation show the ability of the procedure to accurately predict properties of boundary layers subjected to large streamwise accelerations. The procedure is used to conduct a parametric study of the effect of free stream turbulence, heat transfer, Reynolds number, acceleration, and Mach number on boundary layers in supersonic nozzles to assist in the design of a quiet tunnel. Results of the investigation show that, even in the presence of moderate free-stream turbulence levels, the boundary layer in the approach section of the quiet tunnel nozzle relaminarizes and becomes thin enough to be removed by a small slot in the nozzle wall. Furthermore, the calculations indicate that it should be possible to maintain a laminar boundary layer for the entire length of the supersonic portion of the quiet tunnel nozzle.

Kreskovsky, J. P.↗

NASA NTRS1974

Comparison of experimental and predicted performance of 150-millimeter-bore solid and drilled ball bearings to 3 million DN

Seven 150-millimeter-bore ball bearings were run under 8900-newton (2000-lbf) thrust load at speeds from 6670 to 20,000 rpm (1 million to 3 million DN). Four of the bearings had conventional solid balls, and three bearings had drilled (cylindrically hollow) balls with 50-percent mass reduction. The bearings were under-race cooled and slot lubricated with a type 2 ester oil at flow rates from 4.35 x 0.001 to 5.94 x 0.001 cubic meter/min (1.15 to 1.57 gal/min). Friction torque and temperature were measured on all bearings. While there was considerable spread in the temperature data, the drilled ball bearings tended to run slightly cooler than the solid ball bearings at higher speeds. No significant difference in torque was noted, however, between the solid and drilled ball bearings. One bearing of each type was rerun at 17,800-newton (4000-lbf) thrust load. The solid ball bearings performed satisfactorily at 3 million DN. However, at about 2 million DN the drilled ball bearing experienced a broken ball, and cracks appeared in other balls as a result of flexure fatigue. Metallurgical examination of the cracked balls indicated a brittle structure in the bore of the drilled balls.

Scibbe, H. W.↗

NASA NTRS1974

Performance of a short annular dump diffuser using wall trailing-edge suction

A short annular dump (abrupt flow area change) diffuser was tested with suction through wall trailing-edge slots at inlet Mach numbers of 0.19 and 0.27 and at near ambient inlet temperature and pressure, with suction flow varied from zero to 10 percent of the inlet air mass-flow rate. The overall ratio of diffuser exit area to inlet area was 4.0, and the ratio of length to inlet height was 2.0. By applying suction flow separately on either wall or to both walls simultaneously, the original annular jet profile could be altered to either a hub- or tip-biased profile. Diffuser effectiveness was increased from about 25 percent with no suction to 50 percent at 6 percent outer-wall suction and to 52 percent at a combined suction rate on both walls of 10.25 percent. At the same time, diffuser total pressure loss was reduced by one-fourth.

Juhasz, A. J.↗

NASA NTRS1974

Small scale model static acoustic investigation of hybrid high lift systems combining upper surface blowing with the internally blown flap

A static acoustic and propulsion test of a small radius Jacobs-Hurkamp and a large radius Flex Flap combined with four upper surface blowing (USB) nozzles was performed. Nozzle force and flow data, flap trailing edge total pressure survey data, and acoustic data were obtained. Jacobs-Hurkamp flap surface pressure data, flow visualization photographs, and spoiler acoustic data from the limited mid-year tests are reported. A pressure ratio range of 1.2 to 1.5 was investigated for the USB nozzles and for the auxiliary blowing slots. The acoustic data were scaled to a four-engine STOL airplane of roughly 110,000 kilograms or 50,000 pounds gross weight, corresponding to a model scale of approximately 0.2 for the nozzles without deflector. The model nozzle scale is actually reduced to about .17 with deflector although all results in this report assume 0.2 scale factor. Trailing edge pressure surveys indicated that poor flow attachment was obtained even at large flow impingement angles unless a nozzle deflector plate was used. Good attachment was obtained with the aspect ratio four nozzle with deflector, confirming the small scale wind tunnel tests.

Cole, T. W.↗

NASA NTRS1974

Heat-transfer and pressure distributions for laminar separated flows downstream of rearward-facing steps with and without mass suction

Heat-transfer and pressure distributions were measured for laminar separated flows downstream of rearward-facing steps with and without mass suction. The flow conditions were such that the boundary-layer thickness was comparable to or larger than the step height. For both suction and no-suction cases, an increase in the step height resulted in a sharp decrease in the initial heat-transfer rates behind the step. Downstream, however, the heat transfer gradually recovered back to less than or near attached-flow values. Mass suction from the step base area increased the local heat-transfer rates; however, this effect was relatively weak for the laminar flows considered. Even removal of the entire approaching boundary layer raised the post-step heat-transfer rates only about 10 percent above the flatplate values. Post-step pressure distributions were found to depend on the entrainment conditions at separation. In the case of the solid-faced step, a sharp pressure drop behind the step was followed by a very short plateau and relatively fast recompression. For the slotted-step connected to a large plenum but without suction, the pressure drop at the base was much smaller and the downstream recompression more gradual than that for solid-faced step.

Brown, R. D.↗

NASA NTRS1974

Gust alleviation for a STOL transport by using elevator, spoilers, and flaps

Control laws were developed to investigate methods of alleviating the response of a STOL transport to gusty air. The transport considered in the study had triple-slotted, externally blown jet flaps and a large T-tail. The control devices used were the elevator, spoilers, and flaps. A hybrid computing system was used to simulate linearized longitudinal dynamics of the aircraft and to implement a conjugate gradient optimal search algorithm. The aircraft was simulated in the low-speed approach condition only. Feedback control matrices were found which minimized the average of a quadratic functional involving passenger compartment accelerations, pitch angle and rate, flight path angle and speed variations. The optimization was performed for artificially designed gust inputs in the form of predetermined rectangular waveforms. Results were obtained for elevator, spoilers, and flaps acting singly and in combination. Additional results were obtained for unit sinusoidal gust inputs by using the gain matrices computed for the artificial test gusts. Various sensor configurations were also investigated.

Lallman, F. J.↗

NASA NTRS1974

Wind-tunnel investigation of an externally blown flap STOL transport model including and investigation of wall effects

A wind-tunnel investigation was conducted in the Langley V/STOL tunnel and in a scaled version of the Ames 40- by 80-foot tunnel test section installed as a liner in the Langley V/STOL tunnel to determine the effect of test-section size on aerodynamic characteristics of the model. The model investigated was a swept-wing, jet-powered, externally blown flap (EBF) STOL transport configuration with a leading-edge slat and triple-slotted flaps. The model was an 0.1645-scale model of a 11.58-meter (38.0-ft) span model designed for tests in a 40- by 80-foot tunnel. The data compare the aerodynamic characteristics of the model with and without the tunnel liner installed. Data are presented as a function of thrust coefficient over an angle-of-attack range of 0 deg to 25 deg. A thrust-coefficient range up to approximately 4.0 was simulated, most ot the tests being conducted at a free-stream dynamic pressure of 814 Newtons/sq m (17 lb sq ft). The data are presented with a minimum of analysis.

Gentry, G. L., Jr.↗

NASA NTRS1974

Calibration of the Langley 16-foot transonic tunnel with test section air removal

The Langley 16-foot transonic tunnel with test section air removal (plenum suction) was calibrated to a Mach number of 1.3. The results of the calibration, including the effects of slot shape modifications, test section wall divergence, and water vapor condensation, are presented. A complete description of the wind tunnel and its auxiliary equipment is included.

Corson, B. W., Jr.↗

NASA NTRS1974

Interim prediction method for jet noise

A method is provided for predicting jet noise for a wide range of nozzle geometries and operating conditions of interest for aircraft engines. Jet noise theory, data and existing prediction methods was reviewed, and based on this information a interim method of jet noise prediction is proposed. Problem areas are idenified where further research is needed to improve the prediction method. This method predicts only the noise generated by the exhaust jets mixing with the surrounding air and does not include other noises emanating from the engine exhaust, such as combustion and machinery noise generated inside the engine (i.e., core noise). It does, however, include thrust reverser noise. Prediction relations are provided for conical nozzles, plug nozzles, coaxial nozzles and slot nozzles.

Stone, J. R.↗

NASA NTRS1974

Conformal mapping technique for two-dimensional porous media and jet impingement heat transfer

Transpiration cooling and liquid metals both provide highly effective heat transfer. Using Darcy's law in porous media and the inviscid approximation for liquid metals, the local fluid velocity in these flows equals the gradient of a potential. The energy equation and flow region are simplified when transformed into potential plane coordinates. In these coordinates, the present problems are reduced to heat conduction solutions which are mapped into the physical geometry. Results are obtained for a porous region with simultaneously prescribed surface temperature and heat flux, heat transfer in a two-dimensional porous bed, and heat transfer for two liquid metal slot jets impinging on a heated plate.

Siegel, R.↗