Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fiber composites”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,315 records · Page 73
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Thickness threshold study of polyaniline-based lightning strike protection coating for carbon/glass fiber reinforced polymer composites

Different polyaniline (PANI) based lightning strike protection (LSP) coating thicknesses were tested against simulated lightning strike tests to evaluate the threshold thickness of the coating. A series of lightning strike tests were performed on carbon/glass fiber reinforced polymer (CFRP/GFRP) composites subjected to simulated lightning currents ranging from 40 to 100 kA. Five LSP-coated specimens were considered herein: two CFRP and three GFRP composites. A minimum of ~ 345 μm thick PANI-based LSP coating on CFRP and GFRP composites under a 40 kA peak current retained 83 % and 100 % residual strength, respectively. Additionally, GFRP specimens tested against 60 and 100 kA peak currents exhibited 100 % residual strength. Finally, this study proposes that a PANI-based LSP coating is suitable for protecting GFRP composites, while the careful design is necessary for CFRP composites to avoid any catastrophic failure.

36 MATERIALS SCIENCE↗
NASA NTRS2019

Design and Analysis of a Tool for Automated Fiber Placement of Composite Wind Tunnel Blades

For decades, composite wind tunnel blades have been constructed using labor-intensive hand layup processes. Automated Fiber Placement (AFP) is a relatively new technology that has not seen widespread use in manufacturing composite wind tunnel blades. AFP offers the potential for reduced manufacturing time, reduced cost, and improved consistency compared to traditional hand layup procedures. These manufacturing qualities are becoming increasingly important as existing wind tunnel blades are replaced due to impact damage or wear and tear from decades of use. Researchers at the NASA Langley Research Center are currently using the Integrated Structural Assembly of Advanced Composites (ISAAC) facility to investigate the feasibility of AFP for manufacturing composite wind tunnel blades. ISAAC uses manufacturing tools as surfaces on which to place fiber tows. A manufacturing tool was developed for using AFP to build a wind tunnel blade shape. This paper presents the structural design and analysis of this tool, for use with AFP, constructed from high temperature thermoplastics. The tool fabricated by this design process was successfully used for AFP and oven cure of two representative airfoil shaped composite structures.

Brian Mason↗
NASA NTRS1980

Fabrication and evaluation of low fiber content alumina fiber/aluminum composites

The mechanical fabrication of low volume percent fiber, polycrystalline alumina fiber reinforced aluminum composites was accomplished. Wire preform material was prepared by liquid-metal infiltration of alumina fiber bundles. The wires were subsequently encapsulated with aluminum foil and fabricated into bulk composite material by hot-drawing. Extensive mechanical, thermal and chemical testing was conducted on preform and bulk material to develop a process and material data base. In addition, a preliminary investigation of mechanical forming of bulk alumina fiber reinforced aluminum composite material was conducted.

Hack, J. E.↗
NASA NTRS2010

Oxidation of SiC Fiber-Reinforced SiC Matrix Composites with a BN Interphase

SiC-fiber reinforced SiC matrix composites with a BN interphase were oxidized in reduced oxygen partial pressures of oxygen to simulate the environment for hypersonic vehicle leading edge applications. The constituent fibers as well as composite coupons were oxidized in oxygen partial pressures ranging from 1000 ppm O2 to 5% O2 balance argon. Exposure temperatures ranged from 816 C to 1353 C (1500 F to 2450 F). The oxidation kinetics of the coated fibers were monitored by thermogravimetric analysis (TGA). An initial rapid transient weight gain was observed followed by parabolic kinetics. Possible mechanisms for the transient oxidation are discussed. One edge of the composite coupon seal coat was ground off to simulate damage to the composite which allowed oxygen ingress to the interior of the composite. Oxidation kinetics of the coupons were characterized by scanning electron microscopy since the weight changes were minimal. It was found that sealing of the coupon edge by silica formation occurred. Differences in the amount and morphology of the sealing silica as a function of time, temperature and oxygen partial pressure are discussed. Implications for use of these materials for hypersonic vehicle leading edge materials are summarized.

Opila, Elizabeth↗
DOE OSTI2021

Automatic identification and quantification of dense microcracks in high-performance fiber-reinforced cementitious composites through deep learning-based computer vision

Highlights: • A method is presented to detect, locate, quantify, and visualize dense microcracks in HPFRCC. • Quantification of dense microcracks is realized using deep learning method for the first time. • The presented method uses deep learning models that are trained using a realistic dataset size. • The presented method has a high computation efficiency for identifying and quantifying cracks. • The presented method provides crack width with errors up to 50 μm and a R{sup 2} value of 0.984. High-performance fiber-reinforced cementitious composites (HPFRCCs) feature high mechanical strengths, crack resistance, and durability. Under excessive loading, HPFRCCs demonstrate dense microcracks that are difficult to identify using existing methods. This study presents a computer vision method for identification, quantification, and visualization of microcracks in HPFRCCs based on deep learning. The presented method integrates multiple deep learning models and computer vision techniques in a hierarchical architecture. The crack pattern (e.g., number, width, and spacing of cracks) are automatically determined from pictures without human intervention. This study shows that the presented method achieves an accuracy of 0.992 for crack detection and an accuracy finer than 50 μm (R{sup 2} > 0.984) for quantification of crack width when deep learning models are trained using only 200 pictures of HPFRCCs and 200 pictures of conventional concrete with incorporation of data augmentation. The presented method is expected to be also applicable to other materials featuring complex cracks.

36 MATERIALS SCIENCE↗
NASA NTRS2019

Automated Fiber Placement Manufactured Composites for Science Applications

Science instruments with large collecting areas that maintain dimensional stability, such as James Webb Space Telescope and Wide Field Space Telescope, help achieve next generation science advancements. Composite materials often used for science applications include high modulus fibers in cyanate ester matrices to result in dimensionally stable structures with low contamination. Hand lay-up fabrication is the most common approach for science instrument structures. Automated Fiber Placement (AFP) using intermediate modulus fibers is commonplace in aircraft production reducing manufacturing time and increasing quality and consistency. AFP manufacturing for future large science instruments can similarly reduce costs and increase reliability. However, high modulus fibers are more prone to damage than intermediate modulus fibers. This study investigates the manufacturing viability of M55J/RS3C (Tencate) slit tape material using AFP processing. Tencate provides slit tape materials. NASA Langley Research Center (LaRC) manufactured hand layup and AFP lay-up laminates under room temperature for initial trials, Marshall Space Flight Center (MSFC) manufactured AFP laminates under room temperature and elevated temperature conditions to evaluate processing affects. Goddard Space Flight Center (GSFC) tests and evaluates tension and Coefficient of Thermal Expansion (CTE) properties by hand lay-up and AFP slit tape automated manufacturing for large science applications. These results show processing material warm reduces process induced fiber fracture; leading to stiffness and CTE properties consistent with hand lay-up, while observing a slight degradation in tensile strength.

Segal, Kenneth N.↗
NASA NTRS1978

A Report of Observed Effects on Electrical Systems of Airborne Carbon/Graphite Fibers

Results of research on composite materials containing carbon/graphite fibers are presented. It is shown that the release of free carbon/graphite fibers into the environment presents a potential hazard to electrical machinery. The high electrical conductivity of the carbon/graphite fibers coupled with other properties such as small fiber diameter, general short length, and low density which permit the free fibers to become airborne can cause effects which could damage equipment or cause it to malfunction. It is recommended that all manufacturers and users of carbon/graphite fiber composite materials exercise caution in handling free fibers and limit disposal of carbon/graphite fiber composites to controlled land fill.

Source record↗
DOE OSTI2023

Degradation in interfacial shear strength of carbon fiber/ vinyl ester composites due to long-term exposure to seawater using push-out tests

Here, in this study, single fiber (~7-μm diameter) push-out tests are conducted to evaluate hygrothermal effects on the interfacial shear strength (IFSS) of carbon fiber/vinyl ester (CF/VE) composites. Hygrothermal conditioning is achieved by saturating samples in simulated seawater at 40 °C for two years. An investigation has been conducted on the preparation, validity, and interpretation of the push-out test results. First, the authors present a polishing methodology that results in thin films of CF/VE composites in the thickness range of 15–120 μm and produces an average 41.2% drop in IFSS due to long-term hygrothermal exposure. Using scanning electron microscopy (SEM), we show that during the push-out tests, the failure initiates locally at the zone of minimum bond strength at the bottom (away from the indenter), then propagates along the length of the interface. The influence of radial tensile stresses originating due to bending is found to be negligible. Using the SEM imaging of the pushed-out fibers, we validate the failure of the interface to be the primary source of failure. The associated results are found to depend on the thickness of the interface. We then reevaluate the results using the Weibull distribution, knowing that the failure mechanism is analogous to the weakest link theory. The results show a 25.5% drop in the IFSS of the CFVE composite, measured at an infinitesimal scale due to long-term to hygrothermal conditioning at 40 °C. A significant drop in IFSS was observed after reheating above glass transition temperature (T g ) and cooling.

36 MATERIALS SCIENCE↗
NASA NTRS2008

Effects of High-Temperature Annealing in Air on Hi-Nicalon Fiber-Reinforced Celsian Matrix Composites

BN/SiC-coated Hi-Nicalon fiber-reinforced celsian matrix composites (CMC) were annealed for 100 h in air at various temperatures to 1200 C, followed by flexural strength measurements at room temperature. Values of yield stress and strain, ultimate strength, and composite modulus remain almost unchanged for samples annealed up to 1100 C. A thin porous layer formed on the surface of the 1100 C annealed sample and its density decreased from 3.09 to 2.90 g/cu cm. The specimen annealed at 1200 C gained 0.43 wt%, was severely deformed, and was covered with a porous layer of thick shiny glaze which could be easily peeled off. Some gas bubbles were also present on the surface. This surface layer consisted of elongated crystals of monoclinic celsian and some amorphous phase(s). The fibers in this surface ply of the CMC had broken into small pieces. The fiber-matrix interface strength was characterized through fiber push-in technique. Values of debond stress, alpha(sub d), and frictional sliding stress, tau(sub f), for the as-fabricated CMC were 0.31+/-0.14 GPa and 10.4+/-3.1 MPa, respectively. These values compared with 0.53+/-0.47 GPa and 8.33+/-1.72 MPa for the fibers in the interior of the 1200 C annealed sample, indicating hardly any change in fiber-matrix interface strength. The effects of thermal aging on microstructure were investigated using scanning electron microscopy. Only the surface ply of the 1200 C annealed specimens had degraded from oxidation whereas the bulk interior part of the CMC was unaffected. A mechanism is proposed explaining the various steps involved during the degradation of the CMC on annealing in air at 1200 C.

Bansal, Narottam P.↗
NASA NTRS2014

Processing and Characterization of Basalt Fiber Reinforced Ceramic Composites for High Temperature Applications Using Polymer Precursors

The development of high temperature structural composite materials has been very limited due to the high cost of the materials and the processing needed. Ceramics can take much higher temperatures, but they are difficult to produce and form in bulk volumes. Polymer Derived Ceramics (PDCs) begin as a polymer matrix, allowing a shape to be formed, to be cured, and be pyrolized in order to obtain a ceramic with the associated thermal and mechanical properties. The two PDCs used in this development are polysiloxane and polycarbosilane. Polysiloxanes contain a silicon oxycarbide backbone when pyrolized up to 1000degC. Polycarbosilane, an organosilicon polymer, contain a silicon-carbon backbone; around 1200degC, -SiC begins to crystallize. The use of basalt in structural and high temperature applications has been under development for over 50 years, yet there has been little published research on the incorporation of basalt fibers as a reinforcement in composites. Basalt is a naturally occurring material found in volcanic rock. Continuous basalt fiber reinforced PDCs have been fabricated and tested for the applicability of this composite system as a high temperature structural composite material. Testing for this included thermal and mechanical testing per ASTM standard tests.

High Temperature Composites↗
NASA NTRS2014

Processing and Characterization of Basalt Fiber Reinforced Ceramic Composites for High Temperature Applications Using Polymer Precursors

The development of high temperature structural composite materials has been very limited due to the high cost of the materials and the processing needed. Ceramics can take much higher temperatures, but they are difficult to produce and form in bulk volumes. Polymer Derived Ceramics (PDCs) begin as a polymer matrix, allowing a shape to be formed and cured and then to be pyrolized in order to obtain a ceramic with the associated thermal and mechanical properties. The two PDCs used in this development are polysiloxane and polycarbosilane. Polysiloxanes contain a silicon oxycarbide backbone when pyrolized up to 1000C. Polycarbosilane, an organosilicon polymer, contain a silicon-carbon backbone; around 1200C, beta-SiC begins to crystallize. The use of basalt in structural and high temperature applications has been under development for over 50 years, yet there has been little published research on the incorporation of basalt fibers as a reinforcement in composites. Basalt is a naturally occurring material found in volcanic rock. Continuous basalt fiber reinforced PDCs have been fabricated and tested for the applicability of this composite system as a high temperature structural composite material. Thermal and mechanical testing includes oxyacetylene torch testing and three point bend testing.

Ceramic Matrix Composites↗
NASA NTRS1985

Design overview of fiber-reinforced superalloy composites for the Space Shuttle main engine

This preliminary design study evaluated the potential of fiber-reinforced superalloys (FRS) for hot-section components of Space Shuttle Main Engine turbopumps. Emphasis was placed on uncooled turbine blades, with a more limited evaluation of FRS turbine stator vanes. The study included FRS properties evaluation, current structural design capability, and preliminary design and structural analysis. In addition, key technology needs were identified, and a plan was generated to develop operational hardware for advanced versions of the SSME. Based on projections of design properties for FRS composites comprising 50 volume percent of W-4Re-0.38Hf-0.02C wire filaments in a ductile superalloy matrix, it was concluded that FRS turbine blades offer the potential of significant improved operating life and higher temperature capability over the MAR-M-246(Hf) (DS) blades currently used in the SSME.

Lewis, J. R.↗
NASA NTRS1988

Residual stresses in continuous graphite fiber Al metal matrix composites

The residual stresses in graphite fiber reinforced aluminum (Gr/Al) composites with various thermal histories are measured using X-ray diffraction (XRD) methods. The XRD stress analysis is based on the determination of lattice strains by precise measurements of the interplanar spacings in different directions of the sample. The sample is a plate consisting of two-ply P 100 Gr/Al 6061 precursor wires and Al 6061 overlayers. Prior to XRD measurement, the 6061 overlayers are electrochemically removed. In order to calibrate the relationship between stress magnitude and lattice spacing shift, samples of Al 6061 are loaded at varying stress levels in a three-point bend fixture, while the stresses are simultaneously determined by XRD and surface-attached strain gages. The stresses determined by XRD closely match those determined by the strain gages. Using these calibrations, the longitudinal residual stresses of P 100 Gr/Al 6061 composites are measured for various heat treatments, and the results are presented.

Park, Hun Sub↗
NASA NTRS2000

Continuous, linearly intermixed fiber tows and composite molded article thereform

The instant invention involves a process used in preparing fibrous tows which may be formed into polymeric plastic composites. The process involves the steps of (a) forming a carbon fiber tow; (b) forming a thermoplastic polymeric fiber tow; (c) intermixing the two tows; and (d) withdrawing the intermixed tow for further use.

McMahon, Paul E.↗
NASA NTRS1980

Compression panel studies for supersonic cruise vehicles

Results of analytical and experimental studies are summarized for titanium, boron fiber reinforced aluminum matrix composite, Borsic fiber reinforced aluminum matrix composite, and titanium sheathed Borsic fiber reinforced aluminum matrix composite stiffened panels. The results indicate that stiffened panels with continuous joints (i.e., brazed, diffusion bonded or adhesive bonded joints) are more structurally efficient than geometrically similar panels with discrete joints (i.e., spotwelded or bolted joints). In addition, results for various types of fiber reinforced aluminum matrix stiffened panels indicate that titanium sheathed Borsic fiber reinforced aluminum matrix composite panels are the most structurally efficient. Analytical results are also presented for graphite fiber reinforced polyimide matrix composite stiffened panels and superplastically formed and diffusion bonded titanium sandwich panels.

Mcwithey, R. R.↗
DOE OSTI2025

Quality Investigation of Pultruded Carbon Fiber Panels Subjected to Four-Point Flexure via Fiber Optic Sensing

Pultruded carbon fiber-reinforced composites are attractive to the wind energy industry due to the rapid production of highly aligned unidirectional composites with enhanced fiber volume fractions and increased specific strength and stiffness. However, high volume carbon fiber manufacturing remains cost-prohibitive. This study investigates the feasibility of a pultruded low-cost textile carbon fiber-reinforced epoxy composite as a promising material in spar cap production was undertaken based on mechanical response to four-point flexure loading. As spar caps are primarily subjected to flexural loading, large-span four-point flexure was considered, and coupon testing was restricted to tensile modulus and compression strength assessment. High-resolution spatial fiber optic strain sensing was utilized to determine spatial strain distribution during four-point flexure, revealing consistent strain along the length of the part and proved to be an excellent option for process manufacturing quality examination. Additionally, holes with diameters of 2.49 mm, 5.08 mm, and 1.93 mm were drilled through the thickness of full-width parts to determine the feasibility of structural health monitoring of pultruding parts internal to wind blades via fiber optic strain sensing.

Chemistry↗
NASA NTRS1992

Modeling of Euclidean braided fiber architectures to optimize composite properties

Three-dimensional braided fiber reinforcements are a very effective toughening mechanism for composite materials. The integral yarn path inherent to this fiber architecture allows for effective multidirectional dispersion of strain energy and negates delamination problems. In this paper a geometric model of Euclidean braid fiber architectures is presented. This information is used to determine the degree of geometric isotropy in the braids. This information, when combined with candidate material properties, can be used to quickly generate an estimate of the available load-carrying capacity of Euclidean braids at any arbitrary angle.

Armstrong-Carroll, E.↗