SEARCH · Engineering Papers

Results for “attack surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,315 records · Page 73

All sources NASA NTRS DOE OSTI

NASA NTRS1987

Pressure field due to drag reducing outer layer devices in turbulent boundary layers

The wall static pressure in the vicinity of drag reducing outer layer devices in flat wall turbulent boundary layers has been measured and compared with an inviscid theory. Symmetric and cambered airfoil devices have been examined at small angles of attack and very low chord Reynolds numbers. Airfoil devices impose a sequence of strong favorable and adverse pressure gradients on the boundary layer whose drag is to be reduced. At very small angles of attack (+ or - 2 deg), this pressure field extends up to about three chord lengths downstream of the trailing edge of an airfoil device. Also examined are the pressures on the upper and lower surfaces of a symmetric airfoil device in the freestream and near the wall. The freestream pressure distribution around an airfoil section is altered by the wall proximity. The relevance of lift enhancement caused by wall proximity to drag reduction has been discussed. The pressure distributions on the flat wall beneath the symmetric airfoil devices are predicted well by the inviscid theory. However, the remaining pressure distributions are predicted only qualitatively, presumably because of strong viscous effects.

Bandyopadhyay, P. R.↗

NASA NTRS1991

Observations of dynamic stall phenomena using liquid crystal coatings

Novel, shear stress-sensitive/temperature-insensitive liquid crystal coatings have been applied to the surface of an oscillating airfoil in order to ascertain the unsteady fluid physics associated with the dynamic-stall process. Surface microtufts and laser sheet/smoke-particle flow visualization were used to compare the liquid-crystal results. Boundary-layer transition and turbulent separation locations were measured as a function of geometric angle of attack. The results obtained are compared with Eppler (1980) aerodynamic design code predictions.

Reda, Daniel C.↗

NASA NTRS1993

Wall pressure fluctuations beneath swept shock wave/boundary layer interactions

An experimental research program providing basic knowledge and establishing a database on the fluctuating pressure loads produced on aerodynamic surfaces beneath 3D shock wave/boundary layer interactions is presented. A turbulent boundary layer on a flat plate is subjected to interactions with swept planar shock waves generated by sharp fins at angle of attack. Measurements are made for the first time in the aft areas of these interactions, showing fluctuating pressure levels as high as 160 dB.

Garg, S.↗

NASA NTRS1957

An Experimental Hydrodynamic Investigation of the Inception of Vortex Ventilation

Results are presented from a hydrodynamic investigation of the inception of vortex ventilation on modified-flat-plate rectangular lifting surfaces of aspect ratio 0.25 differing in scale and thickness ratio. Two types of bubble-formation processes are described. Inception speeds were correlated for bubble formation in the high angle-of-attack range by using the Froude number and for that in the low angle-of-attack range by expressing the speed as a function of the thickness ratio.

REYNOLDS NUMBER EFFECTS - COMPLETE WINGS↗

NASA NTRS2000

X-38 Experimental Aerothermodynamics

The X-38 program seeks to demonstrate an autonomously returned orbital test flight vehicle to support the development of an operational Crew Return Vehicle for the International Space Station. The test flight, anticipated in 2002, is intended to demonstrate the entire mission profile of returning Space Station crew members safely back to earth in the event of medical or mechanical emergency. Integral to the formulation of the X-38 flight data book and the design of the thermal protection system, the aerothermodynamic environment is being defined through a synergistic combination of ground based testing and computational fluid dynamics. This report provides an overview of the hypersonic aerothermodynamic wind tunnel program conducted at the NASA Langley Research Center in support of the X-38 development. Global and discrete surface heat transfer force and moment, surface streamline patterns, and shock shapes were measured on scaled models of the proposed X-38 configuration in different test gases at Mach 6, 10 and 20. The test parametrics include angle of attack from 0 to 50 degs, unit Reynolds numbers from 0.3 x 10 (exp 6) to 16 x 10 (exp 6)/ ft, rudder deflections of 0, 2, and 5 deg. and body flap deflections from 0 to 30 deg. Results from hypersonic aerodynamic screening studies that were conducted as the configuration evolved to the present shape at, presented. Heavy gas simulation tests have indicated that the primary real gas effects on X-38 aerodynamics at trim conditions are expected to favorably influence flap effectiveness. Comparisons of the experimental heating and force and moment data to prediction and the current aerodynamic data book are highlighted. The effects of discrete roughness elements on boundary layer transition were investigated at Mach 6 and the development of a transition correlation for the X-38 vehicle is described. Extrapolation of ground based heating measurements to flight radiation equilibrium wall temperatures at Mach 6 and 10 were made and generally compared to within 50 deg F of flight prediction.

Horvath, Thomas J.↗

NASA NTRS2011

Ice Shape Characterization Using Self-Organizing Maps

A method for characterizing ice shapes using a self-organizing map (SOM) technique is presented. Self-organizing maps are neural-network techniques for representing noisy, multi-dimensional data aligned along a lower-dimensional and possibly nonlinear manifold. For a large set of noisy data, each element of a finite set of codebook vectors is iteratively moved in the direction of the data closest to the winner codebook vector. Through successive iterations, the codebook vectors begin to align with the trends of the higher-dimensional data. In information processing, the intent of SOM methods is to transmit the codebook vectors, which contains far fewer elements and requires much less memory or bandwidth, than the original noisy data set. When applied to airfoil ice accretion shapes, the properties of the codebook vectors and the statistical nature of the SOM methods allows for a quantitative comparison of experimentally measured mean or average ice shapes to ice shapes predicted using computer codes such as LEWICE. The nature of the codebook vectors also enables grid generation and surface roughness descriptions for use with the discrete-element roughness approach. In the present study, SOM characterizations are applied to a rime ice shape, a glaze ice shape at an angle of attack, a bi-modal glaze ice shape, and a multi-horn glaze ice shape. Improvements and future explorations will be discussed.

McClain, Stephen T.↗

NASA NTRS2006

Visualization of a Capsule Entry Vehicle Reaction-Control System (RCS) Thruster

Planar laser-induced fluorescence (PLIF) was used to visualize the reaction control system (RCS) jet flow emanating from the aft-body of an Apollo-geometry capsule test article in the NASA Langley Research Center 31-Inch Mach 10 Air wind tunnel. The RCS jet was oriented normal to the aft surface of the model and had a nominal Mach number of 2.94. The composition of the jet gas by mass was 95% nitrogen (N2) and 5% nitric oxide (NO). The RCS jet flowrate varied between zero and 0.5 standard liters per minute and the angle of attack and tunnel stagnation pressure were also varied. PLIF was used to excite the NO molecules for flow visualization. These flow visualization images were processed to determine the trajectory and to quantify the flapping of the RCS jet. The spatial resolution of the jet trajectory measurement was about 1 mm and the single-shot precision of the measurement was estimated to be 0.02 mm in the far field of the jet plume. The jet flapping, measured by the standard deviation of the jet centerline position was as large as 0.9 mm, while the jet was 1.5-4 mm in diameter (full width at half maximum). Schlieren flow visualization images were obtained for comparison with the PLIF. Surface pressures were also measured and presented. Virtual Diagnostics Interface (VIDI) technology developed at NASA Langley was used to superimpose and visualize the data sets. The measurements demonstrate some of the capabilities of the PLIF method while providing a test case for computational fluid dynamics (CFD) validation.

Danehy, P. M.↗

NASA NTRS1996

Silicone Contamination Camera for Developed for Shuttle Payloads

On many shuttle missions, silicone contamination from unknown sources from within or external to the shuttle payload bay has been a chronic problem plaguing experiment payloads. There is currently a wide range of silicone usage on the shuttle. Silicones are used to coat the shuttle tiles to enhance their ability to shed rain, and over 100 kg of RTV 560 silicone is used to seal white tiles to the shuttle surfaces. Silicones are also used in electronic components, potting compounds, and thermal control blankets. Efforts to date to identify and eliminate the sources of silicone contamination have not been highly successful and have created much controversy. To identify the sources of silicone contamination on the space shuttle, the NASA Lewis Research Center developed a contamination camera. This specially designed pinhole camera utilizes low-Earth-orbit atomic oxygen to develop a picture that identifies sources of silicone contamination on shuttle-launched payloads. The volatile silicone species travel through the aperture of the pinhole camera, and since volatile silicone species lose their hydrocarbon functionalities under atomic oxygen attack, the silicone adheres to the substrate as SiO_x. This glassy deposit should be spatially arranged in the image of the sources of silicone contamination. To view the contamination image, one can use ultrasensitive thickness measurement techniques, such as scanning variable-angle ellipsometry, to map the surface topography of the camera's substrate. The demonstration of a functional contamination camera would resolve the controversial debate concerning the amount and location of contamination sources, would allow corrective actions to be taken, and would demonstrate a useful tool for contamination documentation on future shuttle payloads, with near negligible effect on cost and weight.

Source record↗

NASA NTRS1987

Low-speed aerodynamic characteristics of a wing-canard configuration with underwing spanwise blowing on the trailing-edge flap system

An investigation of the effects of spanwise blowing applied to the lower surface of a trailing-edge flap system on a wing-canard configuration has been conducted in the Langley 4- by 7-Meter Tunnel. The investigation studied spanwise-blowing angles of 30 deg., 45 deg., and 60 deg. measured from a perpendicular to the body center-line. The test conditions covered a range of free-stream dynamic pressures up to 50 psf for thrust coefficients up to 2.1 over a range of angles of attack from -2 deg. to 26 deg. Model height above the wind tunnel floor was varied from a height-to-span ratio of 1.70 down to 0.20 (a representative wheel touchdown height). The results indicate that blowing angles of 30 deg. and 45 deg. increase the induced-lift increment produced by spanwise blowing on the lower surface of a trailing-edge flap system. Increasing the blowing angle to 60 deg., in general, produces little further improvement.

Banks, Daniel W.↗

NASA NTRSDate not supplied

Progress Toward Evaluating Roughness-Resolved Aerothermodynamic Simulations for the Mars Sample Return Earth Entry System

This work pursues the efficient Navier-Stokes simulation, using NASA’s standard LAURA and DPLR simulation tools, of the flowfield and convective heating resulting from the patterned-roughness surface of the Mars Sample Return (MSR) Earth Entry System (EES). This type of simulation has been infeasible for past NASA missions. However, for EES, the combination of a patterned roughness heatshield approximated with a sinusoidal pattern, the zero degrees angle of attack nominal flow, and the supersonic boundary layer edge Mach number, all combine to make these roughness resolved grid simulations feasible. The patterned roughness and zero degrees angle of attack nominal flow allow the simulation domain to be reduced to a thin axial flowfield slice that captures a minimum of single period of the roughness pattern. With a periodic boundary condition applied along the boundaries of this slice, simulation on the reduced domain is identical to the full domain but with significant cost saving. The supersonic boundary layer edge Mach number prevents the upstream influence, which allows the smooth stagnation region to be frozen. This freezing of the stagnation region flow is required because of the numerical instability resulting from the tight spacing of the grid in the axial direction as the stagnation point is approached. Applying the developed analysis approach to a peak heating EES case results in a roughness augmentation factor for the convective heating of 1.32, which agrees well with correlations that predict values between 1.30 and 1.37. Analysis approach developed in this work provides the framework for future studies of turbulence modeling impacts and the influence of an ablating surface.

Earth Entry System↗

NASA NTRS1989

TranAir: Recent advances and applications

TranAir is a computer code which solves the full-potential equation for transonic flow about very general and complex configurations. Piecewise flat surface panels are used to describe the surface geometry. This paneled definition is then embedded in an unstructured cartesian flow field grid. Finite elements are used in the discretization of the flow field grid in a manner which is fully conservative and second-order accurate. Since geometries may be defined with relative ease, and since the user is not involved in the generation of the flow field grid, computational results may be generated rather quickly for a wide range of geometries. For transonic cases in the cruise angle-of-attack range, TranAir has generated results which are in generally good agreement with both Euler results and wind tunnel data. A typical transonic case runs in 1 to 2 CPU hours on a Cray X-MP. For subcritical cases, the code runs in 15 to 30 CPU minutes, even for geometries in which several thousand surface panels are used in the definition. This ability to rapidly and accurately provide both subsonic and transonic predictions about very complex aircraft configurations gives TranAir the potential of being a very powerful and widely used design tool.

Madson, Michael D.↗

NASA NTRS1989

Calculation of the rotor induced download on airfoils

Interactions between the rotors and wing of a rotary wing aircraft in hover have a significant detrimental effect on its payload performance. The reduction of payload results from the wake of lifting rotors impinging on the wing, which is at 90 deg angle of attack in hover. This vertical drag, often referred as download, can be as large as 15 percent of the total rotor thrust in hover. The rotor wake is a three-dimensional, unsteady flow with concentrated tip vortices. With the rotor tip vortices impinging on the upper surface of the wing, the flow over the wing is not only three-dimensional and unsteady, but also separated from the leading and trailing edges. A simplified two-dimensional model was developed to demonstrate the stability of the methodology. The flow model combines a panel method to represent the rotor and the wing, and a vortex method to track the wing wake. A parametric study of the download on a 20 percent thick elliptical airfoil below a rotor disk of uniform inflow was performed. Comparisons with experimental data are made where the data are available. This approach is now being extended to three-dimensional flows. Preliminary results on a wing at 90 deg angle of attack in free stream is presented.

Lee, C. S.↗

NASA NTRS1962

Tables of Aerodynamic Coefficients Obtained from Developed Newtonian Expressions for Complete and Partial Conic and Spheric Bodies at Combined Angles of Attack and Sideslip with Some Comparisons with Hypersonic Experimental Data

Closed-form expressions and tables composed from these expressions are presented for complete and partial conic and spheric bodies at combined angles of attack and sideslip in Newtonian flow. Aerodynamic coefficients of these bodies are tabulated for various body segments over a range of angles of attack from 1 deg to 85 deg and angles of sideslip from 0 deg to 15 deg. Some comparisons between Newtonian predictions and hypersonic experimental aerodynamic characteristics were made for conic bodies hawing various surface slopes, nose bluntnesses, and body cross sections to indicate the range of validity of the theory. In general, the theory is shown to agree quite well with experimental results for sharp-nose complete cones and for configurations hawing large blunted noses and steep surface slopes. However, agreement between theory and experiment generally is poor for the more slender, slightly blunted complete or half conic bodies and also for sharp-nose half conic bodies where real-flow phenomena such as forebody interference, viscous forces, leeward surface contributions, or leading-edge pressure reductions may have significant effect. The agreement between theory and experiment for the bodies considered can be improved by using the stagnation pressure coefficient behind a normal shock rather than 2 as the Newtonian coefficient, although for the sharp-nose half conic bodies there i s no theoretical justification for this modification.

Armstrong, William O.↗

NASA NTRS1973

Results of Tests OA12 and IA9 in the Ames Research Center unitary plan wind tunnels on an 0.030-scale model of the Space Shuttle Vehicle 2A to determine aerodynamic loads, volume 4

Tests were conducted in wind tunnels during April and May 1973, on an 0.030-scale replica of the Space Shuttle Vehicle Configuration 2A. Aerodynamic loads data were obtained at Mach numbers from 0.6 to 3.5. The investigation included tests on the integrated (launch) configuration and on the isolated orbiter (entry configuration). The integrated vehicle was tested at angles of attack and sideslip from minus 8 degrees to +8 degrees. The isolated orbiter was tested at angles of attack from minus 15 degrees to +40 degrees and angles of sideslip from minus 10 degrees to +10 degrees as dictated by trajectory considerations. The effects of orbiter/external tank incidence angle and deflected control surfaces on aerodynamic loads were also investigated.

Spangler, R. H.↗

NASA NTRS1973

Results of tests OA12 and IA9 in the Ames Research Center unitary plan wind tunnels on an 0.030-scale model of the Space Shuttle Vehicle 2A to determine aerodynamic loads, volume 9

Tests were conducted in the NASA/ARC Unitary Plan wind tunnels on an 0.030-scale replica of the space shuttle vehicle configuration 2A. Aerodynamic loads data were obtained at Mach numbers from 0.6 to 3.5. The investigation included Tests IA9A, B and C on the integrated (launch) configuration and Tests OA12A and C on the isolated orbiter (entry configuration). The integrated vehicle was tested at angles of attack and sideslip from minus 8 degrees to + 8 degrees. The isolated orbiter was tested at angles of attack from minus 15 degrees to + 40 degrees and angles of sideslip from minus 10 degrees to + 10 degrees as dictated by trajectory considerations. The effects of orbiter/external tank incidence angle and deflected control surfaces on aerodynamic loads were also investigated.

Spangler, R. H.↗

NASA NTRS1977

Wind tunnel investigation of the aerodynamic characteristics of symmetrically deflected ailerons of the F-8C airplane

A .042-scale model of the F-8C airplane was investigated in a transonic wind tunnel at high subsonic Mach numbers and a range of angles of attack between-3 and 20 degrees. The effect of symmetrically deflected ailerons on the longitudinal aerodynamic characteristics was measured. Some data were also obtained on the lateral control effectiveness of asymmetrically deflected horizontal tail surfaces.

Gera, J.↗

NASA NTRS1979

Effects of spanwise blowing on the surface pressure distribution and vortex-lift characteristics of a trapezoidal wing-strake configuration

The effects of spanwise blowing on the surface pressures of a 44 deg swept trapezoidal wing-strake configuration were measured. Wind tunnel data were obtained at a free stream Mach number of 0.26 for a range of model angle of attack, jet thrust coefficient, and nozzle chordwise location. Results showed that spanwise blowing delayed the leading edge vortex breakdown to larger span distances and increased the lifting pressures. Vortex lift was achieved at span stations immediately outboard of the strake-wing junction with no blowing, but spanwise blowing was necessary to achieve vortex lift at increased span distances. Blowing on the wing in the presence of the strake was not as effective as blowing on the wing alone. Spanwise blowing increased lift throughout the angle-of-attack range, improved the drag polars, and extended the linear pitching moment to higher values of lift. The leading edge suction analogy can be used to estimate the effects of spanwise blowing on the aerodynamic characteristics.

Campbell, J. F.↗

NASA NTRS1979

On the laminar separation, transition, and turbulent reattachment of low Reynolds number flows near the leading edge of airfoils

The laminar separation, transition, and turbulent reattachment near the leading edge of a cylindrical nose-constant thickness airfoil model were investigated using a low turbulence, low speed smoke wind tunnel. The locations of separation, transition, and reattachment were obtained from smoke flow photographs and surface oil flow techniques for chord Reynolds numbers from about 150,000 to 470,000. These visual data combined with static pressure distributions and lift and drag measurements delineate the effects of angle of attack, flap deflection angle, and chord Reynolds number on the separation bubble characteristics. The data concerning the length of the laminar and turbulent portions of the bubble agree with the empirical prediction methods for short bubbles.

Arena, A. V.↗