Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Separate effect tests”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,315 records · Page 73

Airframe noise component interaction studies

Acoustic wind tunnel tests were conducted to examine the noise-generating processes of an airframe during approach flight. The airframe model was a two-dimensional wing section, to which highlift leading and trailing edge devices and landing gear could be added. Far field conventional microphones were utilized to determine component spectrum levels. An acoustic mirror directional microphone was utilized to examine noise source distributions on airframe components extended separately and in combination. Measured quantities are compared with predictions inferred from aircraft flyover data. Aeroacoustic mechanisms for each airframe component are identified. Component interaction effects on total radiated noise generally were small (within about 2 dB). However, some interactions significantly redistributed the local noise source strengths by changing local flow velocities and turbulence levels. Possibilities for noise reduction exist if trailing edge flaps could be modified to decrease their noise radiation caused by incident turbulent flow.

Fink, M. R.↗

Failure characteristics of graphite-epoxy structural components loaded in compression

Failure characteristics of compressively loaded graphite-epoxy components are described. Experimental results for both strength-critical laminates and structural components with postbuckling strength are presented. Effects of low speed impact damage and circular holes on compressive strength are discussed. Delamination and shear crippling failure mechanisms that limit the performance of strength-critical laminates are described. Transverse shear and skin-stiffener separation failure mechanisms that limit the performance of components with postbuckling strength are also described. The influence of matrix properties on compressive strength improvements for impact damaged laminates is discussed. Experimental data and results from a failure analysis for strength-critical laminates with cutouts are discussed and compared with impact damage results. Typical postbuckling test results are compared with analytical predictions.

Starnes, J. H., Jr.↗

Study of double wall panels for use in propeller driven aircraft

Propeller driven aircraft have exhibited high levels of interior noise. Most absorption materials are not effective at low frequencies where maximum noise levels occur. Two panels separated by an air gap are suggested as an alternative means of noise attenuation. This design produces an impedance mismatch where a sound wave travels backwards to the source. The higher the impedance, the higher the reflected soundwave intensity. Two aluminum panels with helium in between and two panels with one being perforated were investigated. Helium increases the transmission loss because of a greater impedance mismatch than air. The transmission loss of the unperforated panel is higher throughout the frequency range tested.

Atwal, M.↗

Failure characteristics of graphite-epoxy structural components loaded in compression

Failure characteristics of compressively loaded graphite-epoxy components are described. Experimental results for both strength-critical laminates and structural components with postbuckling strength are presented. Effects of low speed impact damage and circular holes on compressive strength are discussed. Delamination and shear crippling failure mechanisms that limit the performance of strength-critical laminates are described. Transverse shear and skin-stiffener separation failure mechanisms that limit the performance of components with postbuckling strength are also described. The influence of matrix properties on compressive strength improvements for impact damaged laminates is discussed. Experimental data and results from a failure analysis for strength-critical laminates with cutouts are discussed and compared with impact damage results. Typical postbuckling test results are compared with analytical predictions. Previously announced in STAR as N83-12174

Starnes, J. H., Jr.↗

Development of an explicit time marching procedure for laminar and turbulent flow

A finite-volume based, time-marching method for turbulent and laminar flows is described. Extensions to the computational procedure to allow the handling of shock induced separation and large regions of strong backflow are emphasized. Two test cases are considered, the United Technologies Research Center (UTRC) separated and reattached turbulent boundary layer and the strong shock case in the McDonnell Douglas Research Lab (MDRL) transonic diffuser G. The extended method worked well on the UTRC flow with a boundary layer blockage of 58% and a maximum backflow velocity of 37% of the local maximum free-stream velocity. It also worked well on the MDRL diffuser with a shock Mach number of 1.353 and a maximum backflow velocity of -71.7 m/s. A Mach number dependent interpolation formula for effective pressure was developed for use in density-update time-marching methods.

Source record↗

Unsteady blade pressure measurements on a model counterrotation propeller

In an exploratory effort an advanced counterrotation propeller instrumented with blade-mounted pressure transducers was tested in the NASA Lewis 9- by 15-Foot Anechoic Wind Tunnel at a simulated takeoff and landing speed of Mach 0.20. The propeller's aft diameter was reduced to investigate possible noise reductions resulting from reduced blade row interaction with the tip vortex. The propeller was tested at three blade row spacings at fixed blade setting angles, at the maximum blade row spacing at higher blade setting angles and at propeller axis angles attack to the flow up to + or - 16 deg. A limited number of unsteady blade surface pressure measurements were made on both rotors of the model counterrotation propeller. Emphasis was placed on determining the effects of rotor-rotor interactions on the blade surface pressures. A unique method of processing the pressure signals was developed that enables even weak interaction waveforms and spectra to be separated from the total signal. The interaction on the aft rotor was many times stronger than that on the forward rotor. The fundamental rotor interaction tone exhibited complicated behavior but generally increased with rotational speed and blade setting angle and decreased with rotor spacing. With the propeller axis at an angle to the flow, the phase response of the aft rotor appeared to be significantly affected by the presence of the forward rotor.

Heidelberg, Laurence J.↗

Unsteady blade pressure measurements on a model counterrotation propeller

In an exploratory effort an advanced counterrotation propeller instrumented with blade-mounted pressure transducers was tested in the NASA Lewis 9- by 15-Foot Anechoic Wind Tunnel at a simulated takeoff and landing speed of Mach 0.20. The propeller's aft diameter was reduced to investigate possible noise reductions resulting from reduced blade row interaction with the tip vortex. The propeller was tested at three blade row spacings at fixed blade setting angles, at the maximum blade row spacing at higher blade setting angles and at propeller axis angles attack to the flow up to + or - 16 deg. A limited number of unsteady blade surface pressure measurements were made on both rotors of the model counterrotation propeller. Emphasis was placed on determining the effects of rotor-rotor interactions on the blade surface pressures. A unique method of processing the pressure signals was developed that enables even weak interaction waveforms and spectra to be separated from the total signal. The interaction on the aft rotor was many times stronger than that on the forward rotor. The fundamental rotor interaction tone exhibited complicated behavior but generally increased with rotational speed and blade setting angle and decreased with rotor spacing. With the propeller axis at an angle to the flow, the phase response of the aft rotor appeared to be significantly affected by the presence of the forward rotor.

Heidelberg, Laurence J.↗

Model tilt-rotor hover performance and surface pressure measurement

A test of a small scale 3-bladed model rotor, with geometry typical of that used on tilt rotor aircraft, was conducted in the Army Aeroflightdynamics Directorate's anechoic hover chamber. The purpose was to determine the hover performance of the rotor and investigate the pressure distributions on a blade at various collective pitch angles and tip speeds. The measured pressures indicate that the rotor did not stall for high collective pitch angles up to theta sub c = 25 deg. This is clearly a 3-D effect since 2-D theory predicts flow separation at these high angles. The flow near the trailing edge separated above theta sub c = 25 deg which caused a sharp increase in power.

Tung, Chee↗

Chain Dynamics in Magnetorheological Suspensions

Magnetorheological (MR) suspensions are composed of colloidal particles which acquire dipole moments when subjected to an external magnetic field. At sufficient field strengths and concentrations, the dipolar particles rapidly aggregate to form long chains. Subsequent lateral cross-linking of the dipolar chains is responsible for a rapid liquid-to-solid-like rheological transition. The unique, magnetically-activated rheological properties of MR suspensions make them ideal for interfacing mechanical systems to electronic controls. Additionally, the ability to experimentally probe colloidal suspensions interacting through tunable anisotropic potentials is of fundamental interest. Our current experimental work has focused on understanding the fluctuations of dipolar chains. It has been proposed by Halsey and Toor (HT) that the strong Landau-Peierls thermal fluctuations of dipolar chains could be responsible for long-range attractions between chains. Such interactions will govern the long-time relaxation of MR suspensions. We have synthesized monodisperse neutrally buoyant MR suspensions by density matching stabilized ferrofluid emulsion droplets with D2O. This allows us to probe the dynamics of the dipolar chains using light scattering without gravitational, interfacial, and polydispersity effects to resolve the short-wavelength dynamics of the dipolar chains. We used diffusing wave spectroscopy to measure these dynamics. The particle displacements at short times that show an independence to the field strength, but at long times exhibit a constrained, sub-diffusive motion that slows as the dipole strength is increased. The experiments are in good qualitative agreement with Brownian dynamics simulations of dipolar chains. Although there have been several important and detailed studies of the structure and interactions in MR suspensions, there has not been conclusive evidence that supports or contradicts the HT model prediction that long-range interactions exist between fluctuating chains of dipolar particles. Resolving this issue would contribute greatly to the understanding of these interesting and important materials. We have begun to test the predictions of the HT model by both examining the dynamics of individual chains and by measuring the forces between dipolar chains directly to accurately and quantitatively assess the interactions that they experience. To do so, we employ optical trapping techniques and video-microscopy to manipulate and observe our samples on the microscopic level. With these techniques, it is possible to observe chains that are fluctuating freely in three-dimensions, independent of interfacial effects. More importantly, we are able to controllably observe the interactions of two chains at various separations to measure the force-distance profile. The techniques also allow us to study the mechanical properties of individual chains and chain clusters. Our work to this point has focused on reversibly-formed dipolar chains due to field induced dipoles where the combination of this chaining, the dipolar forces, and the hydrodynamic interactions that dictate the rheology of the suspensions. One can envision, however, many situations where optical, electronic, or rheological behavior may be optimized with magneto-responsive anisotropic particles. Chains of polarizable particles may have the best properties as they can coil and flex in the absence of a field and stiffen and orient when a field is applied. We have recently demonstrated a synthesis of stable, permanent paramagnetic chains by both covalently and physically linking paramagnetic colloidal particles. The method employed allows us to create monodisperse chains of controlled length. We observed the stability, field-alignment, and rigidity of this new class of materials. The chains may exhibit unique rheological properties in an applied magnetic field over isotropic suspensions of paramagnetic particles. They are also useful rheological models as bead-spring systems. These chains form the basis for our current experiments with optical traps.

Gast, A. P.↗

Role of shielding in modulating the effects of solar particle events: Monte Carlo calculation of absorbed dose and DNA complex lesions in different organs

Distributions of absorbed dose and DNA clustered damage yields in various organs and tissues following the October 1989 solar particle event (SPE) were calculated by coupling the FLUKA Monte Carlo transport code with two anthropomorphic phantoms (a mathematical model and a voxel model), with the main aim of quantifying the role of the shielding features in modulating organ doses. The phantoms, which were assumed to be in deep space, were inserted into a shielding box of variable thickness and material and were irradiated with the proton spectra of the October 1989 event. Average numbers of DNA lesions per cell in different organs were calculated by adopting a technique already tested in previous works, consisting of integrating into "condensed-history" Monte Carlo transport codes--such as FLUKA--yields of radiobiological damage, either calculated with "event-by-event" track structure simulations, or taken from experimental works available in the literature. More specifically, the yields of "Complex Lesions" (or "CL", defined and calculated as a clustered DNA damage in a previous work) per unit dose and DNA mass (CL Gy-1 Da-1) due to the various beam components, including those derived from nuclear interactions with the shielding and the human body, were integrated in FLUKA. This provided spatial distributions of CL/cell yields in different organs, as well as distributions of absorbed doses. The contributions of primary protons and secondary hadrons were calculated separately, and the simulations were repeated for values of Al shielding thickness ranging between 1 and 20 g/cm2. Slight differences were found between the two phantom types. Skin and eye lenses were found to receive larger doses with respect to internal organs; however, shielding was more effective for skin and lenses. Secondary particles arising from nuclear interactions were found to have a minor role, although their relative contribution was found to be larger for the Complex Lesions than for the absorbed dose, due to their higher LET and thus higher biological effectiveness. c2004 COSPAR. Published by Elsevier Ltd. All rights reserved.

Non-NASA Center↗

Parametric Study of Used Nuclear Oxide Fuel Constituent Dissolution in Molten LiCl-KCl-UCl 3

Prior work identified dissolution of used nuclear oxide fuel constituents from a uranium oxide matrix into molten LiCl-KCl-UCl 3 at 500°C, prompting a subsequent series of three progressive studies (including an initial scoping study, an electrolytic dissolution study, and a chemical-seeded dissolution study) to further investigate associated parameters and mechanisms. Thermodynamic calculations were performed to identify possible reaction mechanisms and their propensities in used oxide fuel constituent dissolution. Used nuclear oxide fuels with varying preconditions from fast and thermal test reactors were separately immersed in the subject salt system to assess fuel constituent migration from the bulk fuel matrix to the salt phase in an initial scoping study. Dissolution of expected fuel constituents, including alkali, alkaline earth, lanthanide, and transuranium oxides, into the chloride salt phase varied widely, ranging from 12% to 99% in the initial study. Uranium isotope blending between the salt phase and bulk fuel matrix was also observed, which was attributed to reducing conditions in the fuel matrix. Electrolytic and chemical-seeded dissolution studies were subsequently performed to effect reducing conditions in the fuel. Other parameters, including temperature (at 500°C, 650°C, 725°C, and 800°C) and uranium trichloride concentrations (at 6, 9, and 19 wt% uranium), were investigated in the latter two studies, resulting in fuel constituent dissolution above 90%. Extents of dissolution were based on initial and final fuel constituent concentrations in the oxide fuels following operations in the salt and subsequent removal of the salt via distillation. Finally, in this series of progressive studies, oxide fuel preconditioning and in situ reducing conditions, along with elevated temperature and uranium trichloride concentrations, were the primary parameters promoting used nuclear oxide fuel constituent dissolution in accordance with identified reaction mechanisms.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

New concepts for Reynolds stress transport equation modeling of inhomogeneous flows

The ability to model turbulence near solid walls and other types of boundaries is important in predicting complex engineering flows. Most turbulence modeling has concentrated either on flows which are nearly homogeneous or isotropic, or on turbulent boundary layers. Boundary layer models usually rely very heavily on the presence of mean shear and the production of turbulence due to that mean shear. Most other turbulence models are based on the assumption of quasi-homogeneity. However, there are many situations of engineering interest which do not involve large shear rates and which are not quasi-homogeneous or isotropic. Shear-free turbulent boundary layers are the prototypical example of such flows, with practical situations being separation and reattachment, bluff body flow, high free-stream turbulence, and free surface flows. Although these situations are not as common as the variants of the flat plate turbulent boundary layer, they tend to be critical factors in complex engineering situations. The models developed are intended to extend classical quasi-homogeneous models into regions of large inhomogeneity. These models do not rely on the presence of mean shear or production, but are still applicable when those additional effects are included. Although the focus is on shear-free boundary layers as tests for these models, results for standard shearing boundary layers are also shown.

Perot, J. Blair↗

Single point modeling of rotating turbulent flows

A model for the effects of rotation on turbulence is proposed and tested. These effects which influence mainly the rate of turbulence decay are modeled in a modified turbulent energy dissipation rate equation that has explicit dependence on the mean rotation rate. An appropriate definition of the rotation rate derived from critical point theory and based on the invariants of the deformation tensor is proposed. The modeled dissipation rate equation is numerically well behaved and can be used in conjunction with any level of turbulence closure. The model is applied to the two-equation kappa-epsilon turbulence model and is used to compute separated flows in a backward-facing step and an axisymmetric swirling coaxial jets into a sudden expansion. In general, the rotation modified dissipation rate model shows some improvements over the standard kappa-epsilon model.

Hadid, A. H.↗

Vegetation stress as a feedback mechanism in midlatitude drought

An atmospheric general circulation model with land surface properties represented by the Simplified Simple Biosphere Model is used to investigate the effect of soil moisture and vegetation stress on drought in the mid-latitudes. An idealized land-sea distribution with simple topography is used to remove as many external sources of climate variation as possible. The land consists of a single, flat, rectangular continent covered with prairie vegetation and centered on 44 deg N of an aqua planet. A control integration of 4 years is performed, and several sets of seasonal anomaly integrations are made to test the sensitivity of seasonal climate to low initial (1 April) soil moisture and dormant vegetation like what would occur during a severe drought. It is found that the inclusion of dormant vegetation during the spring and early summer greatly reduces evapotranspiration by eliminating transpiration. This affects local climate more strongly as summer progresses. Low initial soil moisture, combined with dormant vegetation, leads to a severe drought. The reduction in precipitation is much greater in magnitude than that due to low soil moisture alone, and greater than the sum of the effects computed separately. Although the short-term drought is more severe, the dormancy of the vegetation prevents further depletion of moisture in the root zone of the soil, so soil moisture begins to rebound toward the middle of summer.

Dirmeyer, Paul A.↗

Alleviation of Spin-Entry Tendencies through Localization of Wing-Flow Separation

Studies have been made on several wing leading-edge modifications applicable at present to single-engine light aircraft, which produce stabilizing vortices at stall and beyond. These vortices have the effect of fixing the stall pattern of the wing such that the various portions of the wing upper surface stall nearly symmetrically. The lift coefficient produced is maintained at a high level to angles of attack significantly above the stall angle of the unmodified wing, and the divergence in roll usually is reduced to a controllable level. It is hypothesized that these characteristics will help prevent inadvertent spin entry after a stall. Results are presented from recent large-scale wind-tunnel tests of a typical light aircraft, both with and without the modifications. The data indicate (hot the static stall and poststall characteristics of this aircraft, in a typical landing-approach condition, are noticeably improved when it suitable leading-edge modification is employed; and also that no appreciable aerodynamic penalties are evident in the normal flight envelope.

Feistel, T. W.↗

Test Cases for a Clipped Delta Wing with Pitching and Trailing-Edge Control Surface Oscillations

Steady and unsteady measured pressures for a Clipped Delta Wing (CDW) undergoing pitching oscillations and trailing-edge control surface oscillations have been presented . From the several hundred compiled data points, 22 static cases, 12 pitching-oscillation cases, and 12 control-surface-oscillation cases have been proposed for Computational Test Cases to illustrate the trends with Mach number, reduced frequency, and angle of attack. The planform for this wing was derived by simplifying the planform of a proposed design for a supersonic transport which is described as the Boeing 2707-300. The strake was deleted, the resulting planform was approximated by a trapezoid with an unswept trailing edge, and the twist and camber were removed. In order to facilitate pressure instrumentation, the thickness was increased to 6 percent from the typical 2.5 to 3 percent for the supersonic transport. The airfoil is thus a symmetrical circular arc section with t/c = 0.06. A wing of similar planform but with a thinner airfoil of t/c = 0.03 was used in the flutter investigations, and the buffet and stall flutter investigation . Flutter results are also reported both for the 3 per cent thick simplified wing and for a more complex SST model. One of the consequences of the increased thickness of the clipped delta wing is that transonic effects are enhanced for Mach numbers near one. They are significantly stronger than would be the case for the thinner wing. Also, with the combination of high leading edge sweep of 50.5, and the sharp leading edge, a leading edge vortex forms on the wing at relatively low angles of attack, on the order of three degrees. The Appendix discusses some of the vortex flow effects. In addition, a shock develops over the aft portion of the wing at transonic speeds such that at some angles of attack, there is both a leading edge vortex and a shock wave on the wing. Such cases are a computational challenge. Some previous applications of this data set have been for the evaluation of an aerodynamic panel method and for evaluation of a Navier-Stokes capability. Linear theory and panel method results are also presented, which demonstrated the need for inclusion of transonic effects. Flutter calculations for the related wing with t/c=O.O3 are given. In this report several Test Cases are selected to illustrate trends for a variety of different conditions with emphasis on transonic flow effects. An overview of the model and tests are given, and the standard formulary for these data is listed. For each type of data, a sample table and a sample plot of the measured pressures are presented. A complete tabulation and plotting of the Test Cases is given. Only the static pressures and the 1st harmonic real and imaginary parts of the pressures are available. All of the data for the test are included in a microfiche document in the original report and are available in electronic file form. The Test Cases are also available as separate electronic files.

Bennett, Robert M.↗

Planar Investigation of a CobraMRV Reentry Flowfield Using Pulse-Burst, Cross-Correlation DGV

The flowfield around a Co-Optimization Blunt-body Reentry Analysis Mid-lift/drag-ratio Rigid Vehicle (CobraMRV) vehicle is investigated with a combination of high-speed planar laser Mie scattering (PLMS) and pulse-burst cross-correlation Doppler global velocimetry (PB-CC-DGV). Tests were conducted in the NASA Langley 4-foot Supersonic Unitary Plan Wind Tunnel (UPWT) over a range of different tunnel operating conditions and model configurations. Results indicate a complex shock-boundary layer interaction. Scalar information extracted from the PLMS show the evolution of the bow shock structure, while streamwise velocity measurements indicate the spatial evolution of the shock-boundary layer interaction including the growth of the separation shock foot and eventual reacceleration of the flow at farther downstream locations. Assessment of multiple cases show strong Mach and Reynolds numbers driven effects on the character of the shock-boundary layer interactions. Measurement uncertainties ranged from 50 to 150 m/s throughout the region of interest, driven largely by angular uncertainties and instabilities in the laser pointing. The mean accuracy of the freestream measurements was found to be 5.2-percent of tunnel predicted values.

Laser↗

Prediction of space shuttle fluctuating pressure environments, including rocket plume effects

Preliminary estimates of space shuttle fluctuating pressure environments have been made based on prediction techniques developed by Wyle Laboratories. Particular emphasis has been given to the transonic speed regime during launch of a parallel-burn space shuttle configuration. A baseline configuration consisting of a lightweight orbiter and monolithic SRB, together with a typical flight trajectory, have been used as models for the predictions. Critical fluctuating pressure environments are predicted at transonic Mach numbers. Comparisons between predicted environments and wind tunnel test results, in general, showed good agreement. Predicted one-third octave band spectra for the above environments were generally one of three types: (1) attached turbulent boundary layer spectra (typically high frequencies); (2) homogeneous separated flow and shock-free interference flow spectra (typically intermediate frequencies); and (3) shock-oscillation and shock-induced interference flow spectra (typically low frequencies). Predictions of plume induced separated flow environments were made. Only the SRB plumes are important, with fluctuating levels comparable to compression-corner induced separated flow shock oscillation.

Plotkin, K. J.↗