Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PRECIPITATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,315 records · Page 73

Study of retained austenite and nano-scale precipitation and their effects on properties of a low alloyed multi-phase steel by the two-step intercritical treatment

Microstructure evolution and properties were studied in a low carbon low alloyed hot-rolled bainitic steel by annealing and annealing plus tempering. Microstructure of the hot-rolled steel consists of lath bainite and martensite. By annealing at 720 °C for 30 min and water quenching, multi-phase microstructure consisting of intercritical ferrite, tempered bainite/martensite, retained austenite and fresh martensite was obtained. With increasing annealing temperature to 760 °C, microstructure of the steel consisted of intercritical ferrite, fresh martensite without retained austenite. After the second step of tempering at 680 °C for samples annealed both at 720 °C and 760 °C, ~ 8–9% volume fraction of retained austenite was obtained in the multi-phase microstructure. Moreover, fine precipitates of VC with size smaller than 10 nm and copper precipitates with size of ~ 10–50 nm were obtained after tempering. Results from scanning transmission electron microscopy (STEM) give evidence to support that the partitioning of Mn, Ni and Cu is of significance for retained austenite stabilization. Due to the combined contribution of multiphase microstructure, the transformation-induced-plasticity effect of retained austenite and strengthening effect of nanometer-sized precipitates, yield strength greater than 800 MPa, yield to tensile ratio of 0.9, uniform elongation of ~ 9% and good low temperature impact toughness of 147 J at − 40 °C were achieved. - Highlights: • Stable retained austenite was produced in a low alloyed steel. • Partition of Mn, Ni and Cu was confirmed by STEM for austenite stabilization. • Nano-sized VC and Cu precipitates were achieved by second tempering. • High strength–high toughness with low Y/T ratio was obtained.

36 MATERIALS SCIENCE↗

Precipitation behaviour of γ′ phase in Alloy 693

This paper reports the precipitation behaviour of γ′ phase in the newly developed Ni-base superalloy Alloy 693. Precipitation of γ′ particles is studied at different temperatures ranging from 800 °C to 950 °C under isothermal conditions for various time periods. Monomodal, bimodal and trimodal size distributions of γ′ precipitates have been observed depending on the temperature of annealing and the cooling rates. These studies have been carried out using scanning and transmission electron microscopy. Results are compared with existing literature and explained on the basis of classical nucleation and growth theory. - Highlights: •The alloy exhibits multi-modal distribution of γ′ precipitates formed in aged Alloy 693. •The γ′ phase has been found contain up to 4 at% of Nb. •Results have been explained on the basis of classical nucleation and growth models.

36 MATERIALS SCIENCE↗

Deformation induced dynamic recrystallization and precipitation strengthening in an Mg−Zn−Mn alloy processed by high strain rate rolling

The microstructure of a high strain-rate rolled Mg−Zn−Mn alloy was investigated by transmission electron microscopy to understand the relationship between the microstructure and mechanical properties. The results indicate that: (1) a bimodal microstructure consisting of the fine dynamic recrystallized grains and the largely deformed grains was formed; (2) a large number of dynamic precipitates including plate-like MgZn{sub 2} phase, spherical MgZn{sub 2} phase and spherical Mn particles distribute uniformly in the grains; (3) the major facets of many plate-like MgZn{sub 2} precipitates deviated several to tens of degrees (3°–30°) from the matrix basal plane. It has been shown that the high strength of the alloy is attributed to the formation of the bimodal microstructure, dynamic precipitation, and the interaction between the dislocations and the dynamic precipitates. - Highlights: •A bimodal microstructure was formed in a high strain-rate rolled Mg−Zn−Mn alloy. •Plate-like MgZn{sub 2}, spherical MgZn{sub 2} and spherical Mn phases were observed. •The major facet of the plate-like MgZn{sub 2} deviated from the matrix basal plane.

36 MATERIALS SCIENCE↗

Precipitation behavior and phase transformation mechanism of super austenitic stainless steel S32654 during isothermal aging

Highlights: • σ phase formed following a sequence: intergranular, cellular and intragranular. • Cellular σ phase was firstly detected in S32654 aged at 800–900 °C. • Cellular σ growth is controlled by both intergranular and bulk Cr, Mo diffusion. • N-rich zone and Cr diffusion near σ phase induced the nucleation of Cr{sub 2}N. • Local needle-like σ transformed into Cr{sub 2}N and R phase through Cr, Mo diffusion. - Abstract: Thermodynamic calculation as well as microstructure characterization was carried out to investigate the precipitation behavior of super austenitic stainless steel S32654 aged at 700–1100 °C. The corresponding precipitation characteristics and transformation mechanisms of secondary phases were proposed. The results demonstrate that σ phases with various morphologies formed during isothermal aging, and followed a sequence of intergranular, cellular and intragranular with aging temperature. The intergranular σ phase nucleated much faster than the intragranular one due to the lower nucleation energy and higher element diffusion rate at grain boundary. Most intragranular σ phase grew into needle-like shape because of the great difference in mobility of the interfaces formed around it. The cellular σ phase was firstly detected in S32654, and its growth process was successively controlled by intergranular diffusion and then by bulk diffusion of Cr and Mo. Both Cr and Mo bulk diffusion and large needle-like σ phase resulted in the incompleteness of cellular precipitation of σ phase. Another new phenomenon was found that σ phase could induce the precipitation of Cr{sub 2}N ahead of cell boundary, between lamellar σ phases and at the σ/γ interfaces. Meanwhile, local parts of needle-like σ phase gradually transformed into Cr{sub 2}N and R phase through Cr and Mo diffusion from the former to the latters.

36 MATERIALS SCIENCE↗

Effects of precipitates and its interface on thermal conductivity of Mg–12Gd alloy during aging treatment

Highlights: • Hardness and thermal conductivity of alloy can be improved by aging treatment. • The interface between precipitates and matrix transformed coherent into incoherent with increasing aging time. • Coherent interface would impede the improvement of thermal conductivity of alloy. - Abstract: How to simultaneously improve the thermal conductivity and mechanical properties of Mg alloys is an interesting and important issue topic. In the present study, the effect of aging treatment on the thermal conductivity and micro-hardness of Mg–12Gd alloy was investigated. Results indicated that the thermal conductivity and micro-hardness of the alloy could be significantly improved by aging treatment, and Mg–12Gd alloy exhibited a typical aging hardening response with the increasing aging time. At the early stage of aging (4 h), a large number of fine particles precipitated from α-Mg matrix, but thermal conductivity of alloy increased a little, which was attributed to the coherent interface hindering the increase of thermal conductivity. The thermal conductivity increased to the peak value of 75.7 W/(m·K) at the aging time of 300 h, which was about 2.17 times that of as-solutionized alloy. The huge increment in the thermal conductivity of as-aged Mg–12Gd alloy was related to the precipitation of particles and the incoherent interface between precipitates and α-Mg matrix.

36 MATERIALS SCIENCE↗

Characterizing nanoscale precipitation in a titanium alloy by laser-assisted atom probe tomography

Highlights: • Atom-probe tomography was performed on Ti-5Al-5Mo-5V-3Cr wt% after quenching and 300 °C aging. • Isothermal ω phase was identified as Ti-rich and solute depleted after 1 h of aging. • The ω precipitate/matrix interface is O enriched. This may facilitate α formation. • High laser-pulse energies increase the probability of complex ion formation, complicating analysis. • Discrepancies between data from the LEAP 5000 XS and LEAP 4000X Si are discussed. - Abstract: Atom-probe tomography was performed on the metastable β-Ti alloy, Ti-5Al-5Mo-5V-3Cr wt% (Ti-5553), aged at 300 °C for 0 to 8 h, to precipitate the embrittling isothermal ω phase. Accurate precipitate quantification requires monitoring and controlling suitable charge-state ratios in the mass spectrum, which in turn are closely related to the laser pulse energy used. High ultraviolet laser pulse energies result in significant complex molecular ion formation during field-evaporation, causing mass spectral peak overlaps that inherently complicate data analyses. Observations and accurate quantification of the ω-phase under such conditions are difficult. The effect is minimized or eliminated by using smaller laser pulse energies. With a small laser pulse energy, Ti-rich and solute depleted precipitates of the isothermal ω phase with an oxygen enriched interface are observed as early as after 1 h aging time utilizing the LEAP 5000X S (77% detection efficiency). We note that these precipitates were not detected below a 2 h aging time with the LEAP 4000X Si (58% detection efficiency). The results are compared to the archival literature. The Al concentration in the matrix/precipitate interfacial region increases during aging. Nucleation of the α-phase at longer aging times may be facilitated by the O and Al enrichment at the matrix/precipitate interface (both strong α-stabilisers). The kinetics and compositional trajectory of the ω-phase with aging time are quantified, facilitating direct correlation of the APT data to previously published mechanical testing.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Austenite and precipitation in secondary-hardening ultra-high-strength stainless steel

Highlights: • Austenite and precipitation in Ferrium S53 steel were analyzed. • Austenite decreased to less than 5% after cryogenic treatment and tempering. • M{sub 2}C carbide could segregate inside martensite lath or in the larger parallel microstructure. - Abstract: Ferrium S53 is a new secondary-hardening ultra-high-strength stainless steel, with more Cr than other Co-Ni ultra-high-strength steels. Austenite has a great effect on the fracture toughness of this metal, and the carbides that are precipitated are the main strengthening phase of Ferrium S53 steel; in this study, its microstructural changes during heat treatment were observed and analyzed by X-ray diffraction (XRD), Optical microscope (OM), SEM, and transmission electron microscopy (TEM). About 40.85% retained austenite in the quenched sample is decreased to less than 5% after cryogenic treatment and tempering. In the final sample, block austenite is retained austenite, and film austenite around 5 nm in width is reverted austenite. Inside the martensite lath, parallel twin-like structures are actually segregated M{sub 2}C precipitates, and most of them are smaller than 20 nm. These precipitates can be aggregated into a several-micron-long parallel zonal microstructure.

36 MATERIALS SCIENCE↗

Continuous microstructure evolution of ball rolled TWIP Ti15Mo alloy and its effect on phase precipitation behavior

Highlights: • Gradient microstructure was induced by ball rolling method in a Ti15Mo alloy. • Twin density increased and then decreased as increasing distance from surface. • Ultrafine (α + β) duplex structure was formed in the heavily deformed region. • α-phase in plate was precipitated in twined region in slightly deformed region. • Strengthening by formation of sub/nano-grains was notable than that by twins. - Abstract: A β-type Ti15Mo alloy with {332}<113> twinning-induced plasticity (TWIP) effect was utilized to investigate the continuous microstructure evolution of β-matrix by ball rolling method. Precipitation behavior of α-phase and strengthening mechanism were examined in regions with different strain. Amounts of intersected twins were present in the slightly deformed region of β-matrix, and their area fraction decreased with an increase of distance from rolled surface. The β-matrix close to surface was heavily deformed to result in the formation of abundant subgrains and nanograins, which was caused by cooperative occurrence of twinning refinement, intragranular dislocation activities and subgrain rotation. Mechanical twins provided the preferential nucleation sites for plate-like α-phase with strong variant selection. Equiaxed α-phase preferentially nucleated at the boundaries of subgrains and nanograins with weak variant selection to form the ultrafine (α + β) duplex structure. Due to the formation of subgrains and nanograins as well as the strain hardening, strengthening became more significant than that by twinning refinement solely. Similarly, the ultrafine (α + β) duplex structure exhibited a better strengthening effect than that by precipitation of plate-like α-phase. The diversities of deformation microstructure combined with different precipitation behaviors of α-phase are desirable for controlling the mechanical properties of β-type TWIP titanium alloys.

36 MATERIALS SCIENCE↗

Influence of heating rate and aging temperature on omega and alpha phase precipitation in Ti35Nb alloy

Highlights: • The heating rate, isothermal temperature and aging time strongly affect the phase precipitation. • Aged Ti35Nb alloy presented an ultimate tensile strength of 972 MPa with elongation of 7.5%. • The elastic modulus of 78 GPa makes this aged alloy a promising candidate for biomedical application. - Abstract: Metastable β Ti alloys based on Nb exhibit features that make them suitable for load-bearing biomedical applications, so it is crucial to evaluate their phase transformation and properties. This paper discusses the effects of aging heat treatments on the microstructure, phase transformation and mechanical behavior of Ti35Nb alloy. Samples were solution heat treated in the β field, quenched and aged under different conditions of heating rates, isothermal aging temperature and isothermal aging time. To enhance the alloy's mechanical behavior, thermal analysis and high temperature X-ray diffraction experiments coupled with Vickers hardness tests were employed to determine the temperature range of isothermal ω phase precipitation, as well as α phase precipitation temperature, thereby providing information to optimize aging heat treatment conditions. Results indicate that Ti35Nb alloy subjected to a heating rate of 30 °C/min and an isothermal aging temperature of 500 °C applied for 4 h would ensure high mechanical strength and low elastic modulus. The application of these aging conditions led to a microstructure consisting of very refined α phase precipitates homogeneously dispersed in the β phase matrix, presenting an ultimate tensile strength of 972 MPa, elongation of 7.5% and elastic modulus of 78 GPa, making this aged alloy a promising candidate for biomedical applications. These results shed light on the correlations between phase transformations, microstructure and mechanical behavior in high solute content TiNb alloys for biomedical applications.

36 MATERIALS SCIENCE↗

Fatigue and Creep-Fatigue Deformation of an Ultra-Fine Precipitate Strengthened Advanced Austenitic Alloy

An advanced austenitic alloy, HT-UPS (high-temperature ultrafine-precipitation-strengthened), has been identified as an ideal candidate material for the structural components of fast reactors and energy-conversion systems. HT-UPS alloys demonstrate improved creep resistance relative to 316 stainless steel (SS) through additions of Ti and Nb, which precipitate to form a widespread dispersion of stable nanoscale metallic carbide (MC) particles in the austenitic matrix. The low-cycle fatigue and creep-fatigue behavior of an HT-UPS alloy have been investigated at 650 °C and a 1.0% total strain, with an R-ratio of -1 and hold times at peak tensile strain as long as 150 min. The cyclic deformation response of HT-UPS is directly compared to that of standard 316 SS. The measured values for total cycles to failure are similar, despite differences in peak stress profiles and in qualitative observations of the deformed microstructures. Crack propagation is primarily transgranular in fatigue and creep-fatigue of both alloys at the investigated conditions. Internal grain boundary damage in the form of fine cracks resulting from the tensile hold is present for hold times of 60 min and longer, and substantially more internal cracks are quantifiable in 316 SS than in HT-UPS. The dislocation substructures observed in the deformed material differ significantly; an equiaxed cellular structure is observed in 316 SS, whereas in HT-UPS the microstructure takes the form of widespread and relatively homogenous tangles of dislocations pinned by the nanoscale MC precipitates. The significant effect of the fine distribution of precipitates on observed fatigue and creep-fatigue response is described in three distinct behavioral regions as it evolves with continued cycling.

36 MATERIALS SCIENCE↗

Characterization of precipitation in gradient Inconel 718 superalloy

Inconel 718 (IN718) superalloy is a well-established material for the application of aircraft engine and power generator due to its excellent performance at high temperatures. The outstanding mechanical properties of IN718 are largely determined by the precipitates. Here, we investigated the precipitation behaviors and the corresponding mechanical properties of the heat-treated gradient IN718 alloy. The microscopy studies reveal that high-density hexagonal η phase with chemistry of Ni 3 (Al,Ti,Nb) formed in the nanograined IN718 alloy after annealing at 700 °C. Additionally, the compressive stress introduced during severe plastic deformation may have prohibited the formation of γ” phase while accelerated the precipitation of γ’ phase, consequently favoring the precipitation of η phase. The corresponding evolution of mechanical behavior of gradient IN718 alloy is investigated.

36 MATERIALS SCIENCE↗

Precipitation hardening of laser powder bed fusion Ti-6Al-4V

Here, the laser powder bed fusion (PBF-L) additive manufacturing (AM) community has dedicated significant efforts into process optimization and control for defect-free Ti-6Al-4V. As defects become less of an issue for PBF-L Ti-6Al-4V, the processing-structure-properties (PSP) relationships between AM microstructures can now be explored to optimize mechanical properties. Lower temperature aging treatments around 550 °C in wrought Ti-6A-4V have been historically understood to precipitation harden the α phase with an ordered, hexagonal close packed (HCP) α 2 phase. The α 2 phase existed as nanoscale Ti 3 Al precipitates coherent with the parent α phase. The goal of the present investigation was to implement a vacuum heat treatment of 545 °C for 100 hours on PBF-L Ti-6Al-4V. This vacuum heat treatment took place after an initial hot isostatic pressure (HIP) treatment that decomposed the as-built, martensitic microstructure. The vacuum aging successfully produced nanoscale precipitates of α 2 phase within α-laths, confirmed via atom probe tomography (APT). Microstructural-length scale and quasi-static mechanical properties were investigated by nanoindentation and uniaxial tensile tests of miniaturized test specimens. Given the sensitivity of Ti-6Al-4V mechanical properties to small changes in chemistry, all test specimens originated from the same build. The α 2 precipitation resulted in significantly harder α-laths (≈ 2 GPa) as measured via nanoindentation, as well as a relative yield and ultimate tensile strength increase of 60 MPa and 38 MPa, respectively. Analysis of Variance (ANOVA) of the datasets revealed no statistical differences in total elongation between the HIPed and HIPed + aged specimens, indicative of the aging treatment producing a net benefit of strength with no loss in ductility.

36 MATERIALS SCIENCE↗

Effect of impurities on phase transformation and precipitation in a low-carbon steel

Impurity elements have been added to a commercial low carbon steel grade to simulate the levels that could arise as a result of increased scrap recycling during steel production. In this study, continuous cooling transformation (CCT) diagrams were constructed for the steels with varying levels of impurities, and it is shown that impurities suppress the phase transformation across a wide range of cooling rates. It was found that a step was formed in the start temperature curve, separating the reconstructive and displacive transformations. The influence of impurities on both the reconstructive transformation and displacive transformation are discussed. Additionally, Cu precipitates were observed using scanning transmission electron microscopy (STEM) in the highest impurity-containing steel after slow cooling (0.05°C/s), fast cooling (5°C/s) and interrupted cooling. It was found that the precipitation kinetics is in the following order: cementite within the secondary phase and cementite at secondary phase-ferrite interface> ferrite grain boundaries> ferrite grain matrix. Atom-probe tomography (APT) revealed Cu precipitates formed on the surface of cementite lamellae, but not within it. This work offers insights for the phase transformation control and precipitation regulation during the thermomechanical processing of low carbon steels containing impurity elements due to scrap recycling.

36 MATERIALS SCIENCE↗

Electric current-induced precipitation hardening in advanced high-strength steel

Effect of electric current on precipitation hardening for advanced high-strength steel is investigated based on mechanical testing and microscopic observation. Complex-phase steel containing nano-sized Nb-bearing carbides was used. By comparing the flow stress between uniaxial tension with applied electric current (pulsed tension) and without electric current (nonpulsed tension) at various elevated temperatures, the influence of electric current on precipitation hardening was confirmed. A higher values of Vickers hardness and full-width-at-half-maximum were obtained in the pulsed tensile specimen compared to the identically heat treated specimen after the same deformation. Small angle neutron scattering analysis showed that the volume fraction and mean diameter of newly formed precipitates in the pulsed tensile specimen were higher and larger than those in the induction heat treated specimen, respectively. In conclusion, it clearly shows that additional precipitation hardening could be induced by the athermal effect of electric current, which is distinct from the thermal effect of Joule heating.

36 MATERIALS SCIENCE↗

Reaction–Diffusion Coupling Facilitates the Sequential Precipitation of Metal Ions from Battery Feedstock Solutions

Here, the development of new technologies for chemical separations is urgently needed to meet the surging demand for critical materials that has strained resources and caused environmental challenges. Inspired by the classic Liesegang experiment, we demonstrated the separation of critical metal ions based on the coupling of ion diffusion and precipitation kinetics. For this purpose, a model feedstock solution simulating dissolved battery electrodes was placed on top of a hydrogel loaded with a precipitating agent, namely sodium hydroxide. As the lithium, manganese, cobalt, and nickel ions diffused into the gel, a gradient of precipitates formed along the length of the reactor. Elemental analysis of the spatially distributed precipitates showed the enrichment of nickel near the gel-solution interface, followed by the formation of an almost pure (>96%) manganese product further along the reactor. Optimization experiments revealed that a sodium hydroxide concentration of 10 mM and a gel/solution volume ratio of 2:1 favored efficient separations. The robustness of the method was demonstrated in four out of five feedstock compositions of typically used battery cathodes. Our proof-of-concept experiments present a paradigm for critical materials separations that does not require specialty chemicals, binding agents, membranes, or toxic solvents.

25 ENERGY STORAGE↗

Impacts of Precipitation Events on Concentrations of Oxygenated Gas- and Particle-Phase Compounds Observed in the Amazon

Removal of gases and particles by precipitation (wet deposition) is a critical process that significantly influences the transport and chemical transformation of atmospheric compounds. However, there are few studies that directly measure or constrain the rates of this process under real-world conditions. This work quantifies the net change in ambient concentrations during precipitation events (removal rates) of gas- and particle-phase organic compounds at a surface site near Manaus, Brazil, during the GoAmazon2014/5 campaign. Removal rates of identified and unknown compounds that have been previously classified into source-based clusters are measured during rain events and categorized based on estimated properties of compounds and clusters. Highly oxygenated gases, such as isoprene oxidation products, are removed during precipitation events with a median removal rate of 0.09 h –1 and the fastest analyte is removed at a rate of 0.22 h –1 . Removal rates of particle-phase compounds are observed at roughly this median rate, while less soluble gases, such as terpenes, exhibit low removal rates. These results are roughly in agreement with prior theoretical estimates of wet deposition rates for comparable compounds, providing an empirical point of comparison while noting that our metric reflects the net influence of precipitation events rather than wet deposition alone.

atmospheric chemistry↗

Effects on precipitation, clouds, and temperature from long‐range transport of idealized aerosol plumes in WRF‐Chem simulations

Using the Weather Research and Forecasting model with Chemistry (WRF-Chem), we explored the impacts of nonlocal aerosol plumes transported at three different altitudes on a summertime convective system developed in a clean environment over the northeastern United States. Idealized aerosol plumes from forest fire and volcano emissions, which are known to be frequently transported in this region, were prescribed at three separate altitudes on the upstream boundary of WRF-Chem. The low-altitude (1.5–2.5 km) plume characteristic of forest fire emissions intersects the water clouds, resulting in optically thicker clouds and about a 30% decrease in accumulated precipitation. The precipitation response to the idealized aerosol plume is attributed to the aerosol “second indirect effect” and aerosol-induced enhancement in evaporation efficiency. Convection also significantly impacted this low-altitude aerosol plume because wet removal scavenges up to 70% of plume aerosols over regions where deep convection and precipitation occur. In stark contrast, midaltitude (5.6–6.6 km) and high-altitude (11.5–12.5 km) plumes exerted a negligible effect on clouds and precipitation. The apparent highly nonlinear sensitivity of simulated convection to the vertical positioning of nonlocal aerosol plumes is explained in terms of the dominant controls influencing this convection regime and limitations in the microphysics currently implemented in WRF-Chem.

54 ENVIRONMENTAL SCIENCES↗

Mixed-phase clouds and precipitation in Southern Ocean cyclones and cloud systems observed poleward of 64°S by ship-based cloud radar and lidar

Mixed-phase clouds (MPCs), composed of both liquid and ice, are prevalent in Southern Ocean cyclones. A characterisation of these clouds on fine vertical scales is required in order to understand the microphysical processes within these clouds, and for model and satellite evaluations over this region. We investigated three examples of cloud systems collected by ship-mounted remote sensing instruments adjacent to East Antarctica at latitudes between 64°S and 69°S. These cases allow us to examine the properties of mid-level MPCs, with cloud tops between 2 and 6 km. Mid-level MPCs contain multiple layers of supercooled liquid water (SLW) embedded within ice during the passage of cyclones. SLW layers are capped by strong temperature inversions and are observed at temperatures as low as - 31°C. Convective generating cells (GCs) are present inside supercooled liquid-topped mid-level MPCs. The horizontal extent, vertical extent and maximum upward Doppler velocity of these GCs were 0.6 – 3.6 km, 0.7 – 1.0 km and 0.5 – 1.0 m s -1 , respectively, and are consistent with observations from previous lower-latitude studies. Ice precipitation is nearly ubiquitous, except in the thinnest clouds at the trailing end of the observed systems. Seeding of lower SLW layers from above leads to periods with either larger ice particles or greater ice precipitation rates. Additionally, periods of supercooled drizzle lasting up to two hours were observed toward the end of two of the three cyclone systems. This supercooled drizzle turns into predominantly ice precipitation as the result of seeding by ice clouds located above the precipitating SLW layer.

54 ENVIRONMENTAL SCIENCES↗