Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “IMPACT TEST”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,315 records · Page 73
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Ignition of contaminants by impact of high-pressure oxygen

The ignition of oil-film contaminants in high-pressure gaseous oxygen systems, caused by rapid pressurization, was investigated using the NASA/White Sands Test Facility's large-volume pneumatic impact test system. The test section consisted of stainless steel lines, contaminated on the inside surface with known amounts of Mobil DTE 24 oil and closed at one end, which was attached to a high-pressure oxygen system; the test section was pressurized to 48 MPa by opening a high-speed valve. Ignition of the oil was detected by a photocell attached to the closed end of the line. It was found that the frequency of ignition increased as a function of both the concentration of oil and of the pressure of the impacting oxygen. The threshold of ignition was between 25 and 65 mg/sq m. The results were correlated with the present NASA and Compressed Gas Association requirements for maximum levels of organic contaminants.

Pedley, Michael D.↗
NASA NTRS2015

Full-Scale Crash Tests and Analyses of Three High-Wing Single

The NASA Emergency Locator Transmitter Survivability and Reliability (ELTSAR) project was initiated in 2014 to assess the crash performance standards for the next generation of ELT systems. Three Cessna 172 aircraft have been acquired to conduct crash testing at NASA Langley Research Center's Landing and Impact Research Facility. Testing is scheduled for the summer of 2015 and will simulate three crash conditions; a flare to stall while emergency landing, and two controlled flight into terrain scenarios. Instrumentation and video coverage, both onboard and external, will also provide valuable data of airframe response. Full-scale finite element analyses will be performed using two separate commercial explicit solvers. Calibration and validation of the models will be based on the airframe response under these varying crash conditions.

Annett, Martin S.↗
NASA NTRS1992

Large-body impact and extinction in the Phanerozoic

The kill curve for Phanerozoic marine species is used to investigate large-body impact as a cause of species extinction. Current estimates of Phanerozoic impact rates are combined with the kill curve to produce an impact-kill curve, which predicts extinction levels from crater diameter, on the working assumption that impacts are responsible for all "pulsed" extinctions. By definition, pulsed extinction includes the approximately 60% of Phanerozoic extinctions that occurred in short-lived events having extinction rates greater than 5%. The resulting impact-kill curve is credible, thus justifying more thorough testing of the impact-extinction hypothesis. Such testing is possible but requires an exhaustive analysis of radiometric dating of Phanerozoic impact events.

Non-NASA Center↗
NASA NTRS1980

Graphite-epoxy panel compression strength reduction due to local impact

The effects of low velocity impact on the compressive strength of graphite/epoxy structures are reviewed. Extensive tests were conducted on sandwich beams, laminated plates and stiffened panels. Conditions for failures were investigated by impact tests on statically loaded test specimens. Lightly loaded graphite structures (such as aircraft secondary structure) were insensitive to impact damage. In more heavily loaded structures, (such as wing panels), appreciable reductions in compressive strength occurred. The implications of the tests for structural design are discussed by comparing panel masses for designs where ultimate strains were reduced due to impact considerations with the masses of designs with higher ultimate strains. Preliminary test data are presented to show the possibility of improvements in damage to tolerance achievable by using an alternate matrix material.

Card, M. F.↗
DOE OSTI2024

High-throughput quantification of quasistatic, dynamic and spall strength of materials across 10 orders of strain rates

Abstract The response of metals and their microstructures under extreme dynamic conditions can be markedly different from that under quasistatic conditions. Traditionally, high strain rates and shock stresses are achieved using cumbersome and expensive methods such as the Kolsky bar or large spall experiments. These methods are low throughput and do not facilitate high-fidelity microstructure–property linkages. In this work, we combine two powerful small-scale testing methods, custom nanoindentation, and laser-driven microflyer (LDMF) shock, to measure the dynamic and spall strength of metals. The nanoindentation system is configured to test samples from quasistatic to dynamic strain-rate regimes. The LDMF shock system can test samples through impact loading, triggering spall failure. The model material used for testing is magnesium alloys, which are lightweight, possess high-specific strengths, and have historically been challenging to design and strengthen due to their mechanical anisotropy. We adopt two distinct microstructures, solutionized (no precipitates) and peak-aged (with precipitates) to demonstrate interesting upticks in strain-rate sensitivity and evolution of dynamic strength. At high shock-loading rates, we unravel an interesting paradigm where the spall strength vs. strain rate of these materials converges, but the failure mechanisms are markedly different. Peak aging, considered to be a standard method to strengthen metallic alloys, causes catastrophic failure, faring much worse than solutionized alloys. Our high-throughput testing framework not only quantifies strength but also teases out unexplored failure mechanisms at extreme strain rates, providing valuable insights for the rapid design and improvement of materials for extreme environments.

Eswarappa Prameela, Suhas (ORCID:0000000334530184)↗
NASA NTRS1972

Development of methods for fracture control of space shuttle structures

The technology with respect to fracture control requirements of the shuttle is considered. The current state-of-the-art does permit an approach based on linear elastic fracture mechanics concepts. Development and implementation of a fracture control plan should recognize deficiencies and provide adequate resources for the extensive empirical test data which are required. With respect to the cost impact of such tests, recent experiences involving advanced aircraft systems have seen unit cost increases of from 200 to 500 percent.

Smith, G. T.↗
NASA NTRS2002

The NASA John C. Stennis Environmental Geographic Information System

The Environmental Geographic Information System (EGIS) at Stennis Space Center (SSC) covers four counties in Mississippi and four parishes in Louisiana. The EGIS includes 410 data layers including vector and raster data from various public and private sources. These data layers provide information on natural and cultural features. SSC initially used the EGIS to: 1) Monitor on and off-site impacts of propulsion testing; 2) Classify land cover at SSC to predict the impacts of future programs. This viewgraph presentation provides an overview of ongoing projects and future applications for the EGIS.

Cohan, Tyrus↗
NASA NTRS2024

The Effects of Impactor Shape on the Compression After Impact Strength of Carbon/Epoxy Face Sheet Aluminum Honeycomb Core Sandwich Structure

This study presents experimental results of compression after impact (CAI) strength testing of aluminum core sandwich structure with carbon/epoxy face sheets impacted at three different energies with either a 12.7 mm hemispherical, 24.5 mm hemispherical or sharp tip impactor. This study was undertaken to verify whether design allowables typically generated by blunt (hemispherical) impactors may be valid in ‘real world” applications where an impact may not be by a blunt object of a specific size. Results of practical interest in this study were that the visual damage was much easier to see for the sharp impactor, the damage size as detected by thermography was smaller for the sharp impactor for a given impact energy and dent depth was greater for the sharp impactor. The CAI strength results showed that the sharp impactor gave about the same CAI strength values at all three impact energy levels used. The larger hemispherical impactor gave slightly higher CAI results than the smaller blunt impactor. Overall it was deemed difficult to develop a CAI allowable that would cover all impactor shapes with any fidelity and thus using a lower bound strain allowable is suggested.

compression after impact (CAI)↗
NASA NTRS1988

Measurements of matrix cracking and delamination caused by impact on composite plates

Tests were performed measuring the locations and extents of delaminations and matrix crackings in 3-in. by 3-in. Fiberite T300/934 graphite/epoxy plates impacted by 1/2-in. diameter aluminum spheres. Plates with six ply orientations were tested. The impactor speeds ranged from 700 to 1300 in/sec. The plates were inspected by C-scan both before and after impact. The plates were also dissected after impact and examined visually for damage. In addition, the longitudinal and transverse tensile, compressive, and shear properties of the material were measured.

Wu, Hsi-Yung T.↗
NASA NTRSDate not supplied

Lower neck injury criteria for THOR and Hybrid III dummies in rear impact

The objectives of the study are to derive lower-neck-injury probability curves under rear impact loading from matched pair Hybrid III and THOR dummy tests. Methods: Twelve whole-body and 15 isolated head-neck rear-impact sled tests were conducted using the 2 dummies. They were positioned on a rigid seat that was attached to an acceleration sled. The dummies were positioned with the head parallel to the ground, torso against the seat back, and legs stretched such that there was no axial rotation. The acceleration pulse matched the previous in-house human cadaver tests. The 6-axis lower-neck load cell was used in both dummies. For the isolated rear-impact tests,the head-neck was excised from the dummies, and the lower-neck load cell was mounted to the top of the sled with the head parallel to the ground and such that the acceleration vector was in the rear impact mode. Lower-neck loads and lower-neck-injury criteria (LNij) were obtained using the load cell data and survival analysis to develop injury-assessment-risk values and curves for both dummies. The LNij criteria were determined for both dummies using the intercept value corresponding to the 90% probability level for the forces and moments. Results: The log normal and Weibull distributions were the optimal distributions for the Hybrid III and THOR devices. At the 50% risk level, the mean LNij of 1.1 and NCIS was 0.77 for the Hybrid III, and 1.5 NCIS was 0.30 for the THOR device. The quality indices were in the fair range and good range for the 2 dummies, respectively, at this risk level. Conclusions: The lower-neck-based IARCs and IARVs serve as the first dataset for injury assessments, and the THOR may be a better test device for assessing injures in rear impact environments.

Narayan Yoganandan↗
NASA NTRS2017

Shape Effect Analysis of Aluminum Projectile Impact on Whipple Shields

The informed design with respect to hypervelocity collisions involving micrometeoroid and orbital debris (MMOD) is influential to the success of space missions. For an orbit comparable to that of the International Space Station, velocities for MMOD can range from 1 to 15 km/s, with an average velocity around 10 km/cu s. The high energy released during collisions at these speeds can result in damage to a spacecraft, or worst-case, loss of the spacecraft, thus outlining the importance of methods to predict the likelihood and extent of damage due to an impact. Through experimental testing and numerical simulations, substantial work has been conducted to better understand the effects of hypervelocity impacts (HVI) on spacecraft systems and shields; however, much of the work has been focused on spherical impacting particles. To improve environment models for the analysis of MMOD, a large-scale satellite break-up test was performed at the Arnold Engineering and Development Complex to better understand the varied impactor geometries that could be generated from a large impact. As a part of the post-experiment analysis, an undertaking to characterize the irregular fragments generated is currently being performed by the University of Florida under the management of NASA's Orbital Debris Program Office at Johnson Space Center (JSC). DebriSat was a representative, modern LEO satellite that was catastrophically broken up in a HVI test. The test chamber was lined with a soft-catch system of foam panels that captured the fragments after impact. Initial predictions put the number of fragments larger than 2mm generated from the HVI at roughly 85,000. The number of fragments thus far extracted from the foam panels has exceeded 100,000, with that number continuously increasing. The shapes of the fragments vary dependent upon the material. Carbon-fiber reinforced polymer pieces, for instance, are abundantly found as thin, flat slivers. The characterization of these fragments with respect to their mass, size, and material composition needs to be summarized in a form that can be used in MMOD analysis. The mechanism that brings these fragment traits into MMOD analysis is through ballistic limit equations (BLE) that have been developed largely for a few types of materials1. As a BLE provides the failure threshold for a shield or spacecraft component based on parameters such as the projectile impact velocity and size, and the target's materials, thickness, and configuration, it is used to design protective shields for spacecraft such as Whipple shields (WS) to an acceptable risk level. The majority of experiments and simulations to test shields and validate BLEs have, heretofore, largely used spheres as the impactor, not properly reflecting the irregular shapes of MMOD. This shortfall has motivated a numerical impact analysis study of HVI involving non-spherical geometries to identify key parameters that environment models should provide.

Carrasquilla, Maria J.↗
DOE OSTI2019

Constrained tree growth and gas-exchange of seawater-exposed forests in the Pacific Northwest, USA

1. Rising sea levels under climate change may have significant impacts on coastal vegetation dynamics, yet the response of coastal forest growth, gas-exchange, and survival to seawater intrusion remains poorly documented. 2. We conducted a dendroecology study across six sites in western Washington, USA, to examine how tree growth, gas exchange (indexed by basal area increment, BAI, and wood d13C, respectively), and survival varies with seawater exposure through two approaches. First, tree core samples were collected at a site where seawater exposure started only four years prior to sampling, which allowed a cause-and-effect test of the impacts of seawater exposure on trees, and second, samples were collected at five additional sites where we compared downstream to upstream trees under current sea-level conditions. 3. At the seawater intrusion site, BAI and carbon isotope discrimination (?) decreased significantly (p < 0.01) in the year of intrusion (2014) and stayed unchanged thereafter. Four years later (2018), the percentage of recently standing dead trees in the forest was 73.0% basal area. Across the regional assessment, percentage of standing dead trees was significantly greater in downstream than upstream forests at five of the six sites (averaged 37.7±11.0% and 4.3±2.1% basal area for downstream and upstream, respectively). Growth was significantly lower (p < 0.01) at the downstream than upstream for five sites, and ? was lower for all needle-leaf trees (three sites) on the downstream compared to the upstream, but no difference was observed between downstream and upstream for broad-leaf trees (three sites). 4. Synthesis Combined, both the cause-and-effect manipulative study and the regional assessment demonstrate that seawater exposure drives reductions in growth, decreased ? of needle-leaf trees, increased mortality, and greater climate sensitivity, regardless of whether the seawater exposure is recent or long-term.

Costal forests, tree growth, tree-ring, tree morta↗
DOE OSTI2024

Impact of High-Reactivity Advanced Test Reactor Experiments on Photon Heating in Nearby Experiment Locations

The Advanced Test Reactor’s (ATR’s) distinctive ability to provide a wide range of irradiation conditions is attractive for programs pursuing fuel qualification experiments. These potentially high-fuel-load experiments are a relatively new development and produce unexplored effects on nearby experiments. Here, this paper explores how photon heating of such an experiment may affect other nearby experiment programs, ultimately serving to better inform decisions regarding experiment design and risks to programmatic goals. The MC21 (Monte Carlo for the 21st Century) code is used to model and study how gamma heat generation rates and axial effects impact different ATR positions. The results reveal that the proximity of a given experiment’s position to the high-fuel-load one can significantly alter that experiment’s expected axial profile.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2018

Environmental Impact Analysis on the Hydraulic Fracture Test Site (HFTS)

Objective The Hydraulic Fracture Test Site (HFTS) provided a platform to test new extraction and production techniques and technologies to understand fracture geometry and increase the efficiency of shale hydrocarbon production. Eleven test wells were drilled in the Upper and Middle Wolfcamp formations, hydraulically fractured, and produced. Air quality, groundwater quality, and produced water chemistry and microbiology were monitored through the duration of the field experiment and one year into production. Methods BTEX, methane, VOCs, SOx, NOx, and PM 10 were measured 1,000 ft up-wind and 1,000 ft down-wind of the HFTS experiment before operations began, during hydraulic fracturing, flowback, and several months into production to evaluate operational impact on local air quality. The underlying Edward-Trinity Plateau aquifer was monitored using 5 groundwater wells within 2 miles of the HFTS pad; BTEX, methane, petroleum hydrocarbons, and a comprehensive suite of anions and metals were analyzed from samples taken before operations began, during hydraulic fracturing, flowback, and one year after production. Water produced from 3 of the 11 HFTS wells was analyzed for chemical and microbiological properties 1.5 years into production. Observations There was no significant impact to air quality from HFTS operations, although elevated BTEX concentrations were measured 1,000 ft. away from the well-pads during the flowback period. We detected no migration of hydrocarbon or fracture fluid chemical migration into the Edward-Trinity Plateau aquifer. Source waters used for hydraulic fracturing contained naturally occurring high concentrations (~500ppm) of sulfate. Rapid microbially induced corrosion was detected in several wells, leading to biocide dosing. Microbiological populations were significantly altered by biocide treatment, but still continued to increase in population size six months after application. Significance After hydraulic fracturing, detailed chemical and microbiological analysis provides evidence for microbiologicallymediated sub-surface transformations of supplied sulfate and organic carbon into sulfides. This report discusses air quality, water quality, and produced water analytical results for the HFTS experiment and further implications for the unconventional oil and gas industry.

Eisenlord, Sarah↗
DOE OSTI2018

Permeation testing of thermal power plant cooling water impacts of Graphite Oxide (GO)/polymer membranes

The purpose of this project was to investigate how thermoelectric power plant cooling water impacts the energy demands, permeance, and ion rejection of GO/polymer membranes using extended permeation testing. Treatment of cooling tower blowdown water is challenging since this water contains scalants (e.g.: silica, calcium sulfate, calcium carbonate) which can precipitate on membranes, decreasing membrane efficiency and lifetime. In this collaboration with EPRI and a Southwestern US utility, the performance of GO/polymer membranes in desalinating cooling tower blowdown water from three natural-gas fueled power plants was evaluated. Results of cross-flow desalination test durations of three to four weeks demonstrated the long-term stability of the membranes. GO/polymer desalination membranes were shown to tolerate drinking-water level chlorination, which could reduce capital and operational costs. Biofouling and scale formation were minimal on the GO surface, suggesting that industry standard intensive cleaning steps could be reduced. Results also demonstrated pressure-tunable rejection which would allow treat-to-need water recycling, thus likely reducing energy costs for these membranes. Further development of biofouling and scaling resistant desalination membranes could lead to reduced cost for water treatment, potentially allowing for greater use of non-traditional water supplies for thermoelectric power plants.

Biedermann, Laura↗
DOE OSTI2023

Advancing the mechanical integrity and fragmentation behavior of reactive projectiles

A multivariant statistical approach was used to identify treatment conditions that improve the survivability of structural reactive material (SRM) projectiles upon launch and enhance energy release upon impact. The study included both mechanical testing of projectiles as well as their reactive characterization. The projectiles were launched in a high-velocity impact-ignition testing system and impacted an anvil for vented chamber calorimetry. This study examined a link between ultimate compressive stress and combustion performance. Two treatments were applied to consolidated aluminum projectiles including annealing and addition of silica (SiO 2 ) inclusions. Results showed annealing at moderate temperatures resulted in intact SRM projectiles upon launch. Adding small concentrations (1–2 wt. %) of SiO 2 to the SRM promoted fragmentation and combustion performance upon impact. Compared to the untreated projectiles, annealing with SiO 2 inclusion processing treatments improved the energy conversion efficiency from 37–84% (for untreated projectiles) up to 54–98%. In conclusion, increasing interparticle dislocation recovery by annealing while balancing inclusions promoting fragmentation upon impact was the key to optimizing combustion performance for SRM ballistic impact applications.

42 ENGINEERING↗
DOE OSTI2013

Integrated Data Collection Analysis (IDCA) Program — Ammonium Nitrate

The Integrated Data Collection Analysis (IDCA) program is conducting a proficiency study for Small- Scale Safety and Thermal (SSST) testing of homemade explosives (HMEs). Described here are the results for impact, friction, electrostatic discharge, and differential scanning calorimetry analysis of ammonium nitrate (AN). AN was tested, in most cases, as both received from manufacturer and dried/sieved. The participants found the AN to be: 1) insensitive in Type 12A impact testing (although with a wide range of values), 2) completely insensitive in BAM friction testing, 3) less sensitive than the RDX standard in ABL friction testing, 4) less sensitive than RDX in ABL ESD testing, and 5) less sensitive than RDX and PETN in DSC thermal analyses.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Effects of Impact and Target Parameters on the Results of a Kinetic Impactor: Predictions for the Double Asteroid Redirection Test (DART) Mission

Abstract The Double Asteroid Redirection Test (DART) spacecraft will impact into the asteroid Dimorphos on 2022 September 26 as a test of the kinetic impactor technique for planetary defense. The efficiency of the deflection following a kinetic impactor can be represented using the momentum enhancement factor, β , which is dependent on factors such as impact geometry and the specific target material properties. Currently, very little is known about Dimorphos and its material properties, which introduces uncertainty in the results of the deflection efficiency observables, including crater formation, ejecta distribution, and β . The DART Impact Modeling Working Group (IWG) is responsible for using impact simulations to better understand the results of the DART impact. Pre-impact simulation studies also provide considerable insight into how different properties and impact scenarios affect momentum enhancement following a kinetic impact. This insight provides a basis for predicting the effects of the DART impact and the first understanding of how to interpret results following the encounter. Following the DART impact, the knowledge gained from these studies will inform the initial simulations that will recreate the impact conditions, including providing estimates for potential material properties of Dimorphos and β resulting from DART’s impact. This paper summarizes, at a high level, what has been learned from the IWG simulations and experiments in preparation for the DART impact. While unknown, estimates for reasonable potential material properties of Dimorphos provide predictions for β of 1–5, depending on end-member cases in the strength regime.

58 GEOSCIENCES↗