Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DUCTILITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,315 records · Page 73
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Cu-7Cr-0.1Ag Microcomposites Optimized for High Strength and High Condutivity

This paper (i) investigated how the microstructure, conductivity, and mechanical properties of Cu-7Cr-0.1Ag microcomposites were changed by cold drawing and subsequent heat treatment, and (ii) produced the Cu-7Cr-0.1Ag microcomposite with an optimum combination of strength and conductivity. The figure of merit Z (combining strength and conductivity) of the Cu-7Cr-0.1Ag microcomposite was larger than that of the microcomposite without silver for each heat treatment. The value of Z of the Cu-7Cr-0.1Ag microcomposite was a maximum after heat treatment for 1 h at 600 °C, indicating that this was the optimum intermediate heat treatment. The following combinations of conductivity, strength and ductility (measured as elongation to fracture) were obtained by the Cu-7Cr-0.1Ag microcomposite with η = 8: (i) 77.9% IACS (International Annealed Copper Standard), 920 MPa and 3.1%; (ii) 79.3% IACS, 880 MPa and 3.3%; and (iii) 79.9% IACS, 798 MPa and 3.5%. These values for the Cu-7Cr-0.1Ag microcomposite were larger than those of the Cu-7Cr microcomposite.

36 MATERIALS SCIENCE↗
DOE OSTI2018

High-Temperature Erosive Behavior of Plasma Sprayed Cr{sub 3}C{sub 2}-NiCr/Cenosphere Coating

This research examines the deposition of Cr{sub 3}C{sub 2}-NiCr/cenosphere and Cr{sub 3}C{sub 2}-NiCr coatings on MDN 321 steel through the process of plasma spray. In this process, the solid particle erosion test is established at 200, 400, 600 °C with 30° and 90° impact angles. Alumina erodent is adopted to investigate the erosive behavior of the coating at higher temperatures. The properties of the Cr{sub 3}C{sub 2}-NiCr/cenosphere coating are established based on the microhardness, the adhesive strength, the fracture toughness, and the ductility. To quantify volume loss as a result of erosion, an optical profilometer is used. At higher temperature, decrease in the erosion volume loss of Cr{sub 3}C{sub 2}-NiCr/cenosphere and Cr{sub 3}C{sub 2}-NiCr coatings is observed. The erosion-resistive property of Cr{sub 3}C{sub 2}-NiCr/cenosphere coating is higher than that of MDN 321 steel by 76%. This property is influenced by high-temperature stability of mullite, alumina, and protective oxide layer that is formed at elevated temperatures. The morphology of eroded coating discloses a brittle mode of material removal.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Nugget Structure Evolution with Rotation Speed for High-Rotation-Speed Friction-Stir-Welded 6061 Aluminum Alloy

High-rotation-speed friction stir welding (HRS-FSW) is a promising technique to reduce the welding loads during FSW and thus facilitates the application of FSW for in situ fabrication and repair. In this study, 6061 aluminum alloy was friction stir welded at high-rotation speeds ranging from 3000 to 7000 rpm at a fixed welding speed of 50 mm/min, and the effects of rotation speed on the nugget zone macro- and microstructures were investigated in detail in order to illuminate the process features. Temperature measurements during HRS-FSW indicated that the peak temperature did not increase consistently with rotation speed; instead, it dropped remarkably at 5000 rpm because of the lowering of material shear stress. The nugget size first increased with rotation speed until 5000 rpm and then decreased due to the change of the dominant tool/workpiece contact condition from sticking to sliding. At the rotation speed of 5000 rpm, where the weld material experienced weaker thermal effect and higher-strain-rate plastic deformation, the nugget exhibited relatively small grain size, large textural intensity, and high dislocation density. Consequently, the joint showed superior nugget hardness and simultaneously a slightly low tensile ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2018

The Effects of Grain Refinement and Rare Earth Intermetallics on Mechanical Properties of As-Cast and Wrought Magnesium Alloys

The effects of rare earth intermetallics and grain refinement by alloying and hot extrusion on the mechanical properties of Mg-Gd-Al-Zn alloys have been studied to elucidate some useful ways to enhance the mechanical properties of magnesium alloys. It was revealed that aluminum as an alloying element is a much better grain refining agent compared with gadolinium, but the simultaneous presence of Al and Gd can refine the as-cast grain size more efficiently. The presence of fine and widely dispersed rare earth intermetallics was found to be favorable to achieve finer recrystallized grains during hot deformation by extrusion. The presence of coarse dendritic structure in the GZ61 alloy, grain boundary eutectic containing Mg{sub 17}Al{sub 12} phase in the AZ61 alloy, and rare earth intermetallics with unfavorable morphology in the Mg-4Gd-2Al-1Zn alloy was found to be detrimental to mechanical properties of the alloy in the as-cast condition. As a result, the microstructural refinement induced by hot extrusion process resulted in a significant enhancement in strength and ductility of the alloys. The presence of intermetallic compounds in the extruded Mg-4Gd-2Al-1Zn and Mg-2Gd-4Al-1Zn alloys deteriorated tensile properties, which was related to the fact that such intermetallic compounds act as stress risers and microvoid initiation sites.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Characterization of Microstructure, Mechanical Properties and Formability of Cryorolled AA5083 Alloy Sheets

In this work, microstructure, mechanical properties and formability of cryorolled and annealed AA5083 alloy sheets have been characterized and a comparison has been made with cold rolled and annealed sheets. Five-millimeter-thick sheets of this alloy were cryorolled in multiple passes to a final thickness of 1 mm (80% reduction with a true strain of 1.6). Effect of annealing time and temperature on hardness has been studied, and it has been found that a short annealing at 275 °C for 15 min after cryorolling would yield a good combination of strength and ductility. Microstructural investigations showed that the cryorolled and short annealed samples possess bimodal grain structure which is responsible for better mechanical properties than cold rolled sheets. From the experimentally determined forming limit diagrams, the limit strains of cryorolled sheets have been found to be almost equal to conventional cold rolled and annealed sheets in all modes of deformation. No major differences have been found in strain distribution also. This work clearly demonstrates that cryorolling of AA5083 alloy sheets followed by a short annealing with bimodal grain structure can be used for sheet metal forming applications with higher strength and toughness than conventional sheets without any reduction in formability.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Tensile Properties and Fracture Characteristics of Nanostructured Copper and Cu-SiC Nanocomposite Produced by Mechanical Milling and Spark Plasma Sintering Process

The presence of large grains within nanometric and ultrafine grain matrix is an effective method in order to enhance strength while keeping the high ductility of metals. For this purpose, in this research, spark plasma sintering (SPS) was used to consolidate milled Cu and Cu-SiC powders. In SPS process, local sparks with high temperature between particles take place and locally lead to intense grain growth, and therefore, this method has the ability to produce bimodal grain structures in copper and copper-based composites. Microstructural and mechanical studies showed ≈ 185 and ≈ 437 nm matrix grain sizes, high tensile yield strength values of ≈ 188.4 and ≈ 296.9 MPa, and fracture strain values of 15.1 and 6.7% for sintered Cu and Cu-4 vol.% SiC nanocomposite materials, respectively. The presence of nanoparticles promoted the occurrence of static recrystallization and decreased the fraction of coarse grains in microstructure. The high tensile properties of the produced materials are attributed to fine grain size, homogenous dispersion of nanoparticles and retarded grain boundary migration during sintering.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2018

Effect of Different Thermomechanical Processes on the Microstructure, Texture, and Mechanical Properties of API 5L X70 Steel

A commercial API 5L X70 steel plate was subjected to different thermomechanical processes to propose a novel thermomechanical rolling path to achieve improved mechanical properties. Scanning electron microscopy, electron backscatter diffraction, and x-ray texture analysis were employed for microstructural characterization. The results showed that strain-free recrystallized {001} ferrite grains that developed at higher rolling temperature could not meet the American Petroleum Institute (API) requirements. Also, refined and work-hardened grains that have formed in the intercritical region with high stored energy do not provide suitable tensile properties. However, fine martensite–austenite constituents dispersed in ferrite matrix with grains having predominantly {111} and {110} orientations parallel to the normal direction that developed under isothermal rolling at 850 °C provided an outstanding combination of tensile strength and ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Friction Stir Welding of Low-Carbon AISI 1006 Steel: Room and High-Temperature Mechanical Properties

Friction stir welding (FSW) is an ecologically benign solid-state joining process. In this work, FSW of low-carbon AISI 1006 steel was carried out to study the microstructure and mechanical properties of the resulting joints at both room temperature (RT) and 200 °C. In the parameter space investigated here, a rotational tool speed and translation feed combination of 1200 rpm and 60 mm/min produced a defect-free weld with balanced mechanical properties and a superior Vickers microhardness profile compared to all other conditions and to base metal (BM). At faster translation feeds (100 and 150 mm/min), wormhole defects were observed in the weld microstructure and were attributed to higher strain rate experienced by the weld zone. Under tensile loading, welded material exhibited yield strength that was up to 86 and 91% of the BM at RT and 200 °C, respectively. On the other hand, tensile strength of welded material was nearly similar to that of the base metal at both RT and 200 °C. However, at both temperatures the tensile ductility of the welded joints was observed to be significantly lower than the BM. Annealing of the 1200 rpm and 60 mm/min FSW specimen resulted in tensile strength of 102% compared to base material and 47% increase in the strain at failure compared to the as-welded specimen. The Charpy impact values revealed up to 62 and 53% increase in the specific impact energy for the 1200 rpm and 60 mm/min welded joints as compared with the BM.

36 MATERIALS SCIENCE↗
DOE OSTI2018

The Effect of Boron and Zirconium on the Structure and Tensile Properties of the Cast Nickel-Based Superalloy ATI 718Plus

The effects of boron and zirconium on cast structure, hardness, and tensile properties of the nickel-based superalloy 718Plus were investigated. For this purpose, five alloys with different contents of boron and zirconium were cast via vacuum induction melting and then purified via vacuum arc remelting. Microstructural analysis by light-optical microscope and scanning electron microscope equipped with energy-dispersive x-ray spectroscopy and phase studies by x-ray diffraction analysis were performed. The results showed that boron and zirconium tend to significantly reduce dendritic arm spacing and increase the amount of Laves, Laves/gamma eutectic, and carbide phases. It was also found that boron led to the formation of B{sub 4}C and (Cr, Fe, Mo, Ni, Ti){sub 3}B{sub 2} phases and zirconium led to the formation of intermetallic phases and ZrC carbide. In the presence of boron and zirconium, the hardness and its difference between dendritic branches and inter-dendritic spaces increased by concentrating such phases as Laves in the inter-dendritic spaces. These elements had a negative effect on tensile properties of the alloy, including ductility and strength, mainly because of the increase in the Laves phase. It should be noted that the largest degradation of the tensile properties occurred in the alloys containing the maximum amount of zirconium.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Multiple Reflow Cycles and Al{sub 2}O{sub 3} Nanoparticles Reinforcement on Performance of SAC305 Lead-Free Solder Alloy

The effect of Al{sub 2}O{sub 3} nanoparticles reinforcement on melting behavior, microstructure evolution at the interface and joint shear strength of 96.5Sn3Ag0.5Cu (SAC305) lead-free solder alloy subjected to multiple reflow cycles was investigated. The reinforced SAC305 solder alloy compositions were prepared by adding Al{sub 2}O{sub 3} nanoparticles in different weight fractions (0.05, 0.1, 0.3 and 0.5 wt.%) through mechanical dispersion. Cu/solder/Cu micro-lap-shear solder joint specimens were used to assess the shear strength of the solder joint. Differential scanning calorimetry was used to investigate the melting behavior of SAC305 solder nanocomposites. The solder joint interfacial microstructure was studied using scanning electron microscopy. The results showed that the increase in melting temperature (T{sub L}) and melting temperature range of the SAC305 solder alloy by addition of Al{sub 2}O{sub 3} nanoparticles were not significant. In comparison with unreinforced SAC305 solder alloy, the reinforcement of 0.05-0.5 wt.% of Al{sub 2}O{sub 3} nanoparticles improved the solder wettability. The addition of nanoparticles in minor quantity effectively suppressed the Cu{sub 6}Sn{sub 5} IMC growth, improved the solder joint shear strength and ductility under multiple reflow cycles. However, the improvement in solder properties was less pronounced on increasing the nanoparticle content above 0.1 wt.% of the solder alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Low Solution Temperature Heat Treatment of AlSi{sub 9}Cu{sub 3}(Fe) High-Pressure Die-Casting Actual Automotive Components

Usually, high-pressure die-casting (HPDC) components cannot be heat-treated at high temperature without the occurrence of surface blisters, which are unacceptable for surface finish and may reduce the mechanical properties. In this context, the purpose of the present paper was to analyze the effectiveness of special low solution temperature T6 heat treatment in overcoming this limit for HPDC AlSi{sub 9}Cu{sub 3} alloy. Very low solution temperatures (< 450 °C, followed by 165 °C aging) to prevent the occurrence of blisters were combined with commonly used times (from 1 to 16 h) ensuring the feasibility of industrial application. Treatments were conducted on samples extracted from actual castings to evaluate the typical defects encountered in common production. Properties were analyzed by means of visual inspection, microstructural observations, image analysis, hardness, tensile tests and fractography. The results showed that it is possible to use solubilization temperatures below 450 °C for several hours in a T6 treatment to give strengthening without relevant blistering in AlSi{sub 9}Cu{sub 3} alloy. The optimum match of properties was provided by a solution treatment at 430 °C for 4 h followed by an aging at 165 °C for 8 h, which gave a yield increase of ~ 50 MPa, an increase in ductility and the best Quality Index value.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructural Characterization, Mechanical Properties, and Corrosion Resistance of Dental Co-Cr-Mo-W Alloys Manufactured by Selective Laser Melting

In this paper, the microstructure, mechanical properties, and corrosion resistance of the dental Co-Cr-Mo-W alloys fabricated by selective laser melting (SLM) were systematically investigated and correlated. The microstructure of the SLM group (SG) specimens is composed of extremely fine columnar crystals, exhibiting supersaturated and homogeneous character. The matrix mainly consists of face-centered-cubic (FCC) cobalt solid solutions, and minimal hexagonal-close-packed (HCP) cobalt solid solutions. Mechanical test results showed that the 0.2% yield strength of SG was 775 ± 7 MPa, and the ultimate tensile strength was 1118 ± 25 MPa. The elongation of SG was 8.28 ± 0.4%, and the microhardness of SG was 476 ± 10 HV. All of these values largely exceeded the cast group (CG) specimens. The high strength is attributed to their fine columnar crystals and supersaturated matrices. The fewer content from the HCP phase and a lack of intermetallic compounds or eutectic contribute to the high ductility. Furthermore, a higher E{sub corr}, lower I{sub corr} were acquired for better corrosion resistance compared to cast specimens, due to even less composition segregation and more microstructural homogeneity.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Influence of Thermomechanically Controlled Processing on Microstructure and Hydrogen Induced Cracking Susceptibility of API 5L X70 Pipeline Steel

The effect of different thermomechanical controlled processing routes on susceptibility of X70 pipeline steel to hydrogen induced cracking (HIC) have been studied. Two X70 pipeline steel specimens labelled WE and WD were investigated. These specimens have the same chemical composition, but they were processed with seperate thermomechanical treatments parameters. Microstructural examinations showed that WE consists of mainly acicular ferrite and polygonal ferrite, while WD consists of acicular ferrite and bainitic ferrite. After subjecting both specimens to hydrogen charging for 12 and 16 h in 0.2 M sulfuric acid and 3 g/L ammonium thiocyanate, early onset of HIC was observed in specimen WD. Post-hydrogen charging microstructural evaluation showed the nucleation of discontinuous cracks in WD after 12 h of charging. However, extended charging for up to 16 h resulted in HIC along the mid-thickness region of both specimens. Hydrogen diffusion across specimen WE was better than that of specimen WD. Therefore, hydrogen trapping at grain boundaries, banded deformed grains, inclusions and secondary phases such as martensite and cementite aided initiation and propagation of HIC in specimens. Nevertheless, the adverse effect of these features on HIC risks was more prominent in specimen WD compared to specimen WE. The Vickers microhardness values measured in WD (349.6 HV) and WE (307.4 HV) suggest that WD is harder than WE; and higher kernel average misorientation of 0.66° in WD than in WE (0.58°) shows higher dislocation density in WD. The results from slow strain rate tensile test confirmed that specimen WD was stronger and more susceptible to HIC than specimen WE. It was concluded that microstructural phases developed during thermomechanical processing improved strength in WD at the expense of its crack resistance, while WE with lower strength showed more ductility and higher resistance to HIC.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Tool Temperature on Microstructure and Properties of Tailored Hot Stamping Components

Traditional boron steel hot stamping technology can achieve components with full martensite and tensile strength of 1500 MPa. However, fully martensitic hot stamped components exhibit very low level of ductility and are rarely used in energy absorbing structures. Hot stamping with segmented heating and cooling tool can obtain multiphase quenched structures and the tailored mechanical properties. Hot stamping experiment of U-shape component was performed with segmented heating and cooling tool. Mechanical properties of the formed component were measured, and scanning electron microscope and color tint etching were used to quantify the quenched phases achieved under different tool temperatures. The results showed that hardness value decreased from 470 to 230 HV and tensile strength reduced about 50% from 1406 to 730 MPa and elongation increased from 4.19 to 10.20% as tool temperatures increased from 25 to 500 °C. Meanwhile, martensite decreased from 85 to 30% and bainite increased from 12 to 55%, and there was also a small increase in ferrite. In order to get the influence of quenched phases on the strength and hardness of tailored hot stamped component, linear fitting optimization was used to establish mathematical models for area fraction of quenched phases and strength and hardness.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Mechanism of Decrease in Impact Toughness in a Low-Carbon MnCrMoNiCu Plate Steel with Increasing Austenitizing Temperature

In order to reveal how microscopic factors affect the toughness and the occurrence of cleavage fracture of a low-carbon MnCrMoNiCu alloyed steel, a series of thermal treatments was performed on the steel employing a thermomechanical simulator. These involved reheating samples at different temperatures (950-1250 °C), producing different prior austenite sizes, followed by a continuous cooling transformation process. The Charpy V-notch toughness was determined, and the effect of austenite grain size on the ductile-to-brittle transition temperatures of the steel was investigated. The microstructural evolution on the austenite sizes was studied, fracture features were characterized, the critical event for cleavage fracture was identified, and the local cleavage fracture stress σ{sub f} was calculated. The impact toughness decreased as the austenitizing temperature increased. A quantitative relationship between σ{sub f} and the size of the initial cleavage fracture facet (microcrack nucleus) a{sub f} in the lathy martensite + bainite microstructure has been developed.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructure, Texture, and Mechanical Properties of Ni-W Alloy After Accumulative Roll Bonding

In this study, the microstructure, texture, and mechanical properties evolution of Ni-14W (wt.%) alloy processed up to four cycles of accumulative roll-bonding (ARB) were investigated using electron backscatter diffraction, microhardness measurements, and tensile tests. The initial equiaxed grains, with an average size of 10 μm, underwent a strong refinement after ARB processing. The elongated ultrafine grains were parallel to the rolling direction, with a grain thickness of 0.2 µm. The texture after ARB processing was characterized by the typical rolling components (Copper, S and Brass), which showed a tendency toward stabilization after four cycles. The microhardness increased substantially (+ 86%) and seemed to saturate after three cycles. The tensile tests demonstrated that Ni-14W samples subjected to ARB processing exhibited high strength (> 1200 MPa after three ARB cycles) and very poor ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructure and Mechanical Properties of Mg{sub 2}Si/AZ91 Composites In Situ Synthesized by Using Silica Fume as the Si Source

Microstructure and mechanical properties of in situ Mg{sub 2}Si/AZ91 composites fabricated using silica fume as the Si source were investigated. The composites contained α-Mg, network Mg{sub 17}Al{sub 12}, lamellar Mg{sub 17}Al{sub 12}, coarse polygonal Mg{sub 2}Si and needle-type Mg{sub 2}Si. Mischmetal modification eliminated the coarse polygonal Mg{sub 2}Si and resulted in a decreased amount of lamellar Mg{sub 17}Al{sub 12} and refined matrix grain size. Solution and aging treatment made the network Mg{sub 17}Al{sub 12} transform into lamellar Mg{sub 17}Al{sub 12}. As the volume fraction of Mg{sub 2}Si increased, the matrix grain size decreased, the amount of Mg{sub 17}Al{sub 12} increased, and more Mg{sub 17}Al{sub 12} precipitated in grain interiors as a result of the increased Al/Mg ratio caused by increasing the amount of Mg{sub 2}Si. The tensile strength and elastic modulus were much higher for the modified composites than for the unmodified one and increased by both increasing the volume fraction of Mg{sub 2}Si and performing aging treatment. The composites failed in a quasi-cleavage fracture mode, and coarse polygonal Mg{sub 2}Si phases were responsible for the lowest ductility of the unmodified composite. The highest UTS of 291.55 MPa obtained is much higher than those reported so far by using fly ash as the Si source, indicating that silica fume is more suitable as the Si source to synthesize Mg{sub 2}Si/AZ91 composites.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Orientation of Weld Line on Formability of Electron Beam-Welded Dissimilar Thickness Titanium Sheets

Recently, manufacturing industries are looking forward to get insight into the influence of weld orientation on formability of tailor-welded blanks (TWBs) of titanium sheets for design and fabrication of lightweight components. Hence, commercially pure titanium (CP Ti) sheets of 1.0 and 1.2 mm thickness were joined together by electron beam welding process using accelerating voltage of 55 kV, beam current of 14.9 mA and welding speed of 865 mm/min. Two different types of TWBs with weld line perpendicular to the rolling direction (WL ⊥ RD) and weld line parallel to the rolling direction (WL || RD) were fabricated, and subsequently, the tensile test, microstructure and microhardness characterizations were conducted to ensure quality of weld. The limiting dome height (LDH) tests were carried out using laboratory-scale setup to evaluate forming behavior of both the above TWBs in terms of FLD, strain distribution, weld line movement and failure location. It was found that the tensile stress–strain response and formability performance of TWBs were significantly influenced by weld line orientation with lower ductility, ultimate tensile strength and LDH in TWB of WL || RD. Moreover, significant weld line movement and non-uniform strain distribution with necking and subsequently fracture were observed away from the weld line in thinner 1.0 mm CP Ti sheets depending on both sample geometry and weld line orientation.

36 MATERIALS SCIENCE↗