Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMPRESSORS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,315 records · Page 73

An experimental investigation of interfacial temperatures in blade-seal material rubbing of aircraft compressors

Results are presented for the rubbing of rotating (100 m/s) titanium blade specimens, with different plasma-sprayed tip coating, against an abradable porous seal material at two different incursion rates. In general, there was a good correspondence between the average transverse force of rubbing and the seal specimen surface temperature. Instantaneous seal surface temperature measurement showed a significant temperature jump before and after each rubbing with a high rate of cooling during each revolution and a high overall temperature level. Numerical predictions of both blade and seal temperature agreed well for the bare blade tip experiments but were consistently high for the coated blades. This suggests that the thermal properties of the coatings may significantly affect the temperatures and hence the wear characteristics of the system.

Emery, A. F.↗

Three-dimensional flow field in the tip region of a compressor rotor passage. I - Mean velocity profiles and annulus wall boundary layer

A rotating three-sensor, hot-wire probe has been used along with rotor blade static pressure measurements to investigate the complex inviscid and viscid effects in the annulus wall flowfield, including the three components of mean velocity, turbulence intensity, and turbulence stress inside the rotor blade passage. It is found that the tip leakage flow originates near quarter-chord, with peak values occurring near mid-chord. The leakage flow, which is in the form of a jet within the blade row, is augmented by the blade rotation and travels further away from the suction surface than that observed in stationary blade rows and cascades. This leakage flow tends to roll up between the mid-passage and the pressure surface near the tip region; the vortex formation does not occur within the passage in this particular case.

Lakshminarayana, B.↗

Axial Compressor Design and Analysis

Program yields blade configurations and aerodynamic flow fields. Program consists of three sections -- two blade design sections and aerodynamic section Program structured that one section used alone, or aerodynamic section used in conjunction with either or both of blading sections. Program written in FORTRAN IV.

William, J. G.↗

Critical review of the trailing edge condition in steady and unsteady flow. Blade flutter in compressors and fans: Numerical simulation of the aerodynamic loading

Existing interpretations of the trailing edge condition, addressing both theoretical and experimental works in steady, as well as unsteady flows are critically reviewed. The work of Kutta and Joukowski on the trailing edge condition in steady flow is reviewed. It is shown that for most practical airfoils and blades (as in the case of most turbomachine blades), this condition is violated due to rounded trailing edges and high frequency effects, the flow dynamics in the trailing edge region being dominated by viscous forces; therefore, any meaningful modelling must include viscous effects. The question of to what extent the trailing edge condition affects acoustic radiation from the edge is raised; it is found that violation of the trailing edge condition leads to significant sound diffraction at the tailing edge, which is related to the problem of noise generation. Finally, various trailing edge conditions in unsteady flow are discussed, with emphasis on high reduced frequencies.

Radwan, S. F.↗

Compressor cascade performance deterioration caused by sand ingestion

Airfoil cascade erosion and performance deterioration was investigated in a gas particle cascade tunnel. The cascade blades were made of 2024 aluminum alloy and the solid particles used were quartz sand. The results of the experimental measurements are presented to show the change in the blade surface erosion, pressure distribution and the total loss coefficient with erosion. The surface quality of the blades exposed to particulate flows are changing the material surfaces. With time, the surface roughness increases and leads to a decrease in engine performance. It was found that the surface roughness values increase asymptotically to a maximum value with increased erosion. The experimental results indicate that the roughness parameters correlate well against the mass of particles impacting unit area of the surface. Such a correlation is useful in aerodynamics and performance computations in turbomachinery.

Tabakoff, W.↗

End wall flows in rotors and stators of a single stage compressor

A computer code for solving the parabolized Navier-Stokes equations for internal flows was developed. Oscillations that develop in the calculation procedure are discussed. The measurements made in the hub and annulus wall boundary layers are summarized. The flow in the hub wall boundary layer, starting ahead of the inlet guide vanes to the inlet of the rotor is traced.

Govindan, T. R.↗

Three dimensional flow field inside compressor rotor, including blade boundary layers

The space marching code was modified in order to be able to predict the flow field inside a rotor passage, including the blade and hub wall boundary layers. The basic changes incorporated are modifications of the equations so that the code can handle three dimensional configurations with changes in the radial direction (for example changes in stagger angle, blade camber and thickness), extensions and modifications in order to implement a physically realistic turbulence model such as a k sigma model and an algebraic Reynolds stress model.

Pouagare, M.↗

Design procedures for compressor blades

The conventional methods for the design of the blades in the case of axial turbomachines are considered, taking into account difficulties concerning the determination of optimal blade profiles. These difficulties have been partly overcome as a consequence of the introduction of new numerical methods during the last few years. It is pointed out that, in the case of the subsonic range, a new procedure is now available for the determination of the form of blade profile on the basis of a given velocity distribution on the profile surface. The search for a profile form with favorable characteristics is consequently transformed into a search for a favorable velocity or pressure distribution on the blade. The distribution of velocities depends to a large degree on the characteristics of the profile boundary layers. The considered concept is not new. However, its practical implementation has only recently become possible. The employment of the new design procedure is illustrated with the aid of an example involving a concrete design problem.

Starken, H.↗

Experiences with nonsynchronous forced vibration in centrifugal compressors

The high subsynchronous vibrations which are often forced vibrations caused by flow instabilities, such as stage stall were examined. Modifications to improve the rotor stability by changing the bearings or seals have little effects on the subsynchronous vibrations. Understanding of the differences between forced vibrations and self excited vibrations to properly diagnose the problem and to correct it, is recommended. A list of characteristics of the two types of subsynchronous vibration is presented.

Smith, D. R.↗

Influence of stationary components on unsteady flow in industrial centrifugal compressors

An experimental investigation was performed to determine the characteristics of the onset and the growth of rotating nonuniform flow in a standard low specific speed stage, normally utilized in high pressure applications, in relation to change of stationary component geometry. Four configurations, differing only in the return channel and crossover geometry were tested on an atmospheric pressure open loop test rig. Experimental results make conspicious the effect of return channel geometry and give the possibility of shifting the unstable zone onset varying such geometry. An attempt was made to interpret the experimental results in the Emmons - Stenning's rotating stall theory.

Bonciani, L.↗

Thermodynamic evaluation of transonic compressor rotors using the finite volume approach

Progress made in extending the finite volume explicit time marching method to laminar and turbulent flow during the time period from January to May 1985 is documented. Previously, extensions were made to the finite volume method to improve the accuracy of the calculation of total pressure in compressible inviscid flow. The current work extends these ideas and develops new ideas which allow the calculation of laminar and turbulent boundary layers in internal flows. The method is verified using four test cases with free-stream Mach numbers ranging from .075 to 1.20.

Nicholson, S.↗

Thermodynamic evaluation of transonic compressor rotors using the finite volume approach

Research at NASA Lewis Research Center gave the opportunity to incorporate new control volumes in the Denton 3-D finite-volume time marching code. For duct flows, the new control volumes require no transverse smoothing and this allows calculations with large transverse gradients in properties without significant numerical total pressure losses. Possibilities for improving the Denton code to obtain better distributions of properties through shocks were demonstrated. Much better total pressure distributions through shocks are obtained when the interpolated effective pressure, needed to stabilize the solution procedure, is used to calculate the total pressure. This simple change largely eliminates the undershoot in total pressure down-stream of a shock. Overshoots and undershoots in total pressure can then be further reduced by a factor of 10 by adopting the effective density method, rather than the effective pressure method. Use of a Mach number dependent interpolation scheme for pressure then removes the overshoot in static pressure downstream of a shock. The stability of interpolation schemes used for the calculation of effective density is analyzed and a Mach number dependent scheme is developed, combining the advantages of the correct perfect gas equation for subsonic flow with the stability of 2-point and 3-point interpolation schemes for supersonic flow.

Moore, J.↗

Thermodynamic evaluation of transonic compressor rotors using the finite volume approach

The finite volume explicit time marching method was refined and improved. Previously, extension had been made to the finite volume method to improve the accuracy of the calculation of total pressure in inviscid flow, extend the method to allow the calculation of laminar and turbulent boundary layers in internal flows, and improve the shock capturing properties of the method by introducing a Mach number dependent interpolation scheme for the pressure used in the calculating the density. The current work extends these developments by using the new pressure interpolation scheme in two dimensional viscous calculations, including a more complete description of the viscous stresses, introducing a criteria for the transverse upwind differencing which is a function of the ratio of transverse and streamwise mass fluxes, and allowing the calculation of internal flow where boundary layers are present on both walls of the duct. The manner in which the viscous stresses are evaluated in the nonorthogonal, nonuniform grid is detailed. The convergence is investigated and results for calculations of laminar flow in a converging duct are presented. Results for calculations of transonic flow in a converging-diverging nozzle are presented and the results are compared with Sajben's measurements and calculations by others.

Nicholson, S.↗