Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “nanostructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Equilibrium distribution of point defects in Fe-Y-O as a typical representative of nanocluster-strengthened alloys

The statistical mechanic approach has been used to estimate the equilibrium defect distribution in a multiphase system by minimizing its free energy using microstructural characteristics and a finite set of defects obtained by first-principles calculations. Recently the approach was extended to take in consideration defects at the interface of the precipitate and matrix. Herein we apply the developed approach to the investigation of the stability of bcc Fe containing yttria, Y 2 O 3 , nanoclusters as a prototype of nanostructured ferritic alloys. It has been obtained that (100)Fe-O interface is unstable with respect to vacancies production. In a contrast to (100)Fe-O interface, the so called Klim interface is stable, i.e. local vacancy concentration at this interface at 600 K is below 10 -12 . It has been demonstrated that due to large defect formation energies the ODS particles are extremely stable and the main defect corresponds to Fe atoms substitute Y in Y 2 O 3 precipitate. Moreover, under thermodynamic equilibrium condition, the preexist vacancies in bulk Fe do not accumulate oxygen atom. The later observation not necessarily forbid the existence of a large amount of preexisting Fe vacancy - oxygen atom clusters at the initial stages of alloy formation far from equilibrium.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Deuterium transport and retention properties of representative fusion blanket structural materials

Reduced activation ferritic-martensitic (RAFM) steels have been developed for decades for use as fusion blanket structural materials, and have advantages in both mechanical properties and irradiation resistance following careful engineering of the microstructure. However, the hydrogen isotope behavior in these proposed fusion structural materials is not well understood, but is important to assess since it impacts the fusion reactor safety and self-sufficient tritium fuel cycle. Here, we investigated deuterium transport and retention in representative advanced RAFM steels, including castable nanostructured alloys (CNAs), and oxide-dispersion-strengthened (ODS) steels. A gas-driven permeation (GDP) system was used to measure the permeability, diffusivity and solubility of the studied materials, covering the temperature range from 623 K to 873 K, and the loading pressures from 1.8 x 10 4 to 1.0 x 10 5 Pa. The results indicated that the deuterium permeability has little material dependence. In contrast, the deuterium diffusivity of the studied materials showed significant variation. The deuterium diffusivity in ODS steels is one order of magnitude lower than that in RAFM steels and CNAs, and correspondingly, have an effective solubility that is 2–10 times larger than RAFM steels and CNAs. In addition, thermal desorption spectroscopy (TDS) measurements were performed to assess the deuterium retention and desorption of these materials following a static thermal deuterium charging at 723 Kfor 1 hour under the deuterium pressure of 1.0 x 10 5 Pa. It was found that ODS steels exhibit the highest deuterium retention and have broader desorption peaks. Microstructural features contributing to deuterium retention and impacting deuterium transport are discussed to rationalize the observed deuterium behavior in the studied RAFM steels.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A short review of defect superlattice formation in metals and alloys under irradiation

Irradiation damage drives complex and coupled phenomena in materials at far-from-equilibrium conditions. The self-organization of nanoscale defects in materials under irradiation shows great potential to tailor the physical properties of materials by controlling nanopatterned microstructures. Irradiation-induced gas bubble and void superlattices are two important ordered nanostructures of great scientific interest. Although both types of superlattices have been investigated extensively, a consensus has yet to be reached on their formation mechanisms. In this review article, the current research status of gas bubble and void superlattices in metals and alloys and their characterization, structural stability, and mechanistic modeling are summarized. The fundamental research goals to advance the mechanistic understanding of gas bubble and void superlattices are outlined.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Synergies between H, He and radiation damage in dual and triple ion irradiation of candidate fusion blanket materials

Three ferritic/martensitic alloys were studied to understand the synergistic effect between single ion beam (Fe 2+ ), dual ion beam (Fe 2+ +He 2+ and Fe 2+ +H + ), and triple ion beam (Fe 2+ +He 2+ +H + ) irradiations on cavity evolution. A commercial alloy, F82H, a castable nanostructured alloy, CNA3, and a high purity model alloy, Fe8Cr2W, were irradiated at 400°C to 600°C to a damage level of 50 dpa at a damage rate of 1 × 10 –3 dpa/s with He and H injection rates of 10 and 40 appm/dpa, respectively. Post-irradiation characterization via bright field transmission electron microscopy and high-angle annular dark-field scanning transmission electron microscopy was performed on all irradiated conditions to characterize the cavity size distribution and determine the effects of H/He injection on cavity microstructure. In all three alloys, hydrogen co-injection with helium resulted in an increased cavity number density and maximum cavity size, producing an increase in swelling over that from helium injection alone. Swelling in F82H appears to peak between 450°C and 500°C. At 600°C, swelling was minimal and cavities of high density and small size were confined to grain boundaries and dislocations while at 400°C, swelling is also low with a nearly homogeneous, high density, distribution of very small cavities throughout. Swelling was least in the commercial alloy F82H due to the high sink strength. The CNA3 alloy underwent dissolution of precipitates that lowered the sink strength and resulted in higher swelling than F82H, but less than the model alloy. Electron energy loss spectroscopy (EELS) elemental mapping revealed hydrogen forming a halo-like structure about the periphery of the cavities and helium residing within the cavities themselves. Finally, this observation suggests that hydrogen reduces the surface energy of helium-filled cavities which results in both increased cavity number density and cavity size in triple beam irradiation over dual beam irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Cold spray manufacturing of oxide-dispersion strengthened (ODS) steels using gas-atomized and ball-milled 14YWT powders

The cold spray deposition process has been investigated for the manufacture of 14YWT oxide-dispersion strengthened (ODS) steel, a nanostructured ferritic alloy (NFA), using gas-atomized and ball-milled feedstock powders. Cold spraying of the gas-atomized powder resulted in a thick dense deposit, but annealing them above 900 °C induced grain growth and heterogeneous precipitation of nanoparticles, thus resulting in lower hardness (~ 170 HV) compared to 14YWT ODS steel manufactured by the conventional method. The ball-milled powder (Fe-14Cr-3W-0.4Ti-0.2Y-0.125O) was cryomilled in liquid N 2 to achieve small particle sizes followed by annealing in a H 2 /Ar environment at 1000 °C and 1100 °C to reduce the hardness from ~ 8 GPa to ~ 5 GPa. Both smaller particle sizes and lower hardness of annealed powders made them amenable to the cold spray deposition process, resulting in thick and dense deposits, while retaining the favorable fully solutionized microstructure of the ball-milled powders. The microstructure of the as-deposited ODS exhibited very fine grain sizes (50–250 nm) with a uniform dispersion of Y-Ti-O nanoprecipitates in the ferritic steel matrix. The hardness values of the cold spray deposits using the powders annealed at 1000 °C and 1100 °C was 770 HV and 496 HV, respectively. Post-heat treatment of the as-deposited material up to 1100 °C showed a high-density microstructure with uniformly dispersed nanoscale oxide particles. The hardness of the annealed deposits up to 1000 °C had a notably higher hardness than bulk 14YWT ODS steel manufactured by conventional methods. The study demonstrates that cold spray deposition of the microstructurally-tailored feedstock powders can be used to successfully manufacture ODS steel with microstructure and properties comparable to those produced by the conventional methods, while providing for an attractive option for the more rapid and cost-effective manufacturing of ODS steel cladding tubes.

14YWT↗
DOE OSTI2022

Highly reversible Zn anode with a practical areal capacity enabled by a sustainable electrolyte and superacid interfacial chemistry

Aqueous zinc-metal batteries are plagued by poor Zn reversibility owing to zinc dendrite and layered double hydroxide (LDH) formation. Here, we introduce a novel additive—N,N-dimethylformamidium trifluoromethanesulfonate (DOTf)—in a low-cost aqueous electrolyte that can very effectively address these issues. The initial water-assisted dissociation of DOTf into triflic superacid creates a robust nanostructured solid-electrolyte interface (SEI)—revealed by operando spectroscopy and cryomicroscopy—which excludes water and enables dense Zn deposition. We demonstrate excellent Zn plating/stripping in a Zn||Cu asymmetric cell for more than 3,500 cycles. Furthermore, near 100% CE is realized at a combined high current density of 4 mA cm -2 and an areal capacity of 4 mAh cm -2 over long-term cycling. Zn||Zn 0.25 V 2 O 5 ·nH 2 O full cells retain ~83% of their capacity after 1,000 cycles with mass-limited Zn anodes. By restricting the depth of discharge, the cathodes exhibit less proton intercalation and LDH formation with an extended lifetime of 2,000 cycles.

25 ENERGY STORAGE↗
DOE OSTI2023

Rational design of septenary high-entropy alloy for direct ethanol fuel cells

Promoting C–C bond cleavage of ethanol by a complete 12-electron (12e) ethanol oxidation reaction (EOR) is a grand challenge for the development of highly efficient direct ethanol fuel cells (DEFCs). Most state-of-the-art catalysts only implement the EOR in an incomplete 4e or 2e pathway because of the poisoning of the catalysts by strongly adsorbed CO, leading to the poor output performance and low cell efficiency of DEFCs. Herein, a septenary PtPdFeCoNiSnMn high-entropy alloy (PtPd HEA) with a PtPd-rich surface but super-low platinum group metals loading was developed. We identified and proved the functions of each element in the PtPd HEA. The DEFCs assembled with the PtPd HEA (0.12 mg PtPd ∙cm -2 ) achieved a maximum power density of 0.72 W cm -2 and a durable operation for 1,200 h, which outperforms state-of-the-art catalysts for DEFCs. This work will be a design principle for nanostructured alloy development for renewable energy and sustainability applications.

25 ENERGY STORAGE↗
DOE OSTI2023

Long-term durability test of highly efficient membrane electrode assemblies for anion exchange membrane seawater electrolyzers

Direct seawater electrolysis faces fundamental electrochemical challenges, such as suppression of chlorine adsorption and/or evolution reactions that poison the current state-of-the-art anode catalysts and accelerate the degradation of the anion exchange membrane (AEM). The technically favored solution path for addressing these issues includes development of novel selective catalysts and implementation of limited operating conditions. Therefore, development of highly active, selective, cost-effective, and stable seawater-splitting catalysts is required for a successful commercialization of the AEM water electrolyzers (AEMWEs). In this work, we report for the first-time an extended operation for over 1000 h of advanced AEMWEs, operating directly with seawater. To fabricate the membrane electrode assemblies (MEAs), catalyst coated electrodes (CCEs) are assembled with Sustainion® X37-50 grade T anion exchange membranes. The anode CCEs are fabricated by spraying an ink prepared from nanostructured NiFe-layered double hydroxide (LDH) catalyst that are synthesized by the solvothermal method and deposited directly onto platinized titanium porous transport layers (PTLs). The cathode CCEs are prepared by spraying an ink prepared from commercial Renay-Nickel catalyst onto a nickel fiber felt. As prepared AEM electrolyzer cells operated with seawater and demonstrated better than previously reported in the literature performance of over 1000 h of operation at a constant current density of 300 mA cm –2 .

25 ENERGY STORAGE↗
DOE OSTI2020

In-situ observation of nano-oxide and defect evolution in 14YWT alloys

Nanostructured ferritic alloys (NFAs) are considered as candidates for structural components in advanced nuclear reactors due to their excellent radiation resistance as a result of a high density of nano-oxides (NOs) in the microstructure. Therefore, gaining an understanding on the stability of NOs under irradiation is crucial. In this study, we have investigated the evolution of defects and NOs in 14YWT NFAs under in-situ Kr ion irradiation at room temperature (RT) and 450°C up to 10 dpa. It has been found that irradiations at 450°C do not create any changes in the NOs, similar to the bulk irradiations. On the other hand, elemental mapping indicates that NOs dissolve mostly after 10 dpa irradiations at RT. Thus, while defects are both annihilated and pinned by NOs at low doses (before the dissolution of NOs), glissile loops start to escape to the foil surface at high doses (after the dissolution of NOs), justifying the significantly low fraction of (111) loops compared to the literature values. Furthermore, high resolution transmission electron microscopy analysis has shown that the NOs are mostly coherent Y 2 Ti 2 O 7 particles with pyrochlore crystal structure after both RT and 450°C irradiations, similar to those observed before irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Direct Observation of Tungsten Oxidation Studied by In Situ Environmental TEM

In this study, in situ environmental transmission electron microscopy (ETEM) was applied, for the first time, to investigate the thermal oxidation of a pristine and a self-ion irradiated polycrystalline tungsten, using a MEMS-based gas cell at 500 oC to 900 oC in a 1 bar 2%O2/N2 gas mixture. By tracking the dynamic evolution of the tungsten oxide scale as it initiates, grows, and sublimates during a consecutive thermal oxidation experiment, we observed two distinctive tungsten oxide microstructure – one nanocrystalline o-WO3 scale grown on W{27-1 } and W{1-1 8} and another o-WO3 scale exhibits a novel highly textured nanostructure. While the two oxide microstructures shared a similar thickness of ~200 nm after 40-minute early-stage oxidation, the nanocrystalline scale on the W{27-1 } grew much more rapidly at 800 oC than the highly textured oxide at a higher temperature of 900 oC. This suggests both the microstructure of these tungsten oxide scales as well as their oxidation kinetics are highly sensitive to the tungsten surface orientation, and such correlations also change dynamically in the course of oxidation. We also discuss the tungsten oxidation mechanism, the effects of the TEM foil thickness, and the focused ion beam (FIB) Ga+ damage on in situ ETEM oxidation.

In situ ETEM, Tungsten, Thermal oxidation, Orienta↗
DOE OSTI2023

Automated phase segmentation and quantification of high-resolution TEM image for alloy design

In the alloy design and development process, a wealth of atomically resolved structural high-resolution transmission electron microscopy (HRTEM) images are produced. Identifying the different nano-precipitate phases and tracking their evolution under various compositions and during manufacturing or post-processing requires hundreds of HRTEM images and thousands of precipitates. The nanoscopic phase information labeling and analysis purely relies on humans are prohibitively costly and time-consuming, sometimes not reliable because of the lack of authoritative knowledge. Here, in this work, we develop a novel unsupervised machine learning approach coupled with adaptive computer vision techniques with features in the Fourier space to automatically determine the number of phases and segment/quantify the phases with nanoscale resolution, allowing for quantitative correlation between nanostructure formation, processing and functional properties. To automate the phase extraction/quantification and ascertain its applicability, we have applied the developed framework to the HRTEM images from several alloy systems, processing conditions, image magnifications, and phase types and morphologies (precipitates, nano-twins, stacking faults, crystalline matrix, and amorphous structures) for verification. This study paves the road for compression, visualization, and translation of raw image structural data into physically relevant information in real-time with minimal human supervision. It shows the promise of enabling high-throughput materials characterization for the acceleration of alloy manufacturing and design.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Underlying mechanism of structural transformation between GaSb and GaAs response to intense electronic excitation

Ion irradiation of semiconductors has emerged as a promising approach for fabricating self-organized nanosystems with high atomic precision, despite often being accompanied by undesirable phenomena. Exploring the mechanisms underlying structural transformations is crucial for assessing nanostructure array types under complex irradiation environments. By quantitatively calculating the thermodynamically driven processes and analyzing the impact of intrinsic structural parameters, distinct structural transformations in response to intense electronic excitation are systematically investigated in gallium antimonide (GaSb) and gallium arsenide (GaAs) systems. In high-energy regimes, the nanofibers layer of GaSb exhibits intriguing structural discrepancy, characterized by partial nanofibers with coherent boundaries, interspersed nanopores accompanied by antisite defects and Ga precipitates, distinguishing to a series of discontinuous latent tracks that emerged within cylindrical trajectories in GaAs. Furthermore, significant diffusion behaviors of the nanohillocks are discovered in GaAs, with higher average roughness than GaSb, driven by the gradient stress distribution influenced by the free-surface effects. The deposition energy for melting phase formation, Gibbs free energy, and Ga diffusion coefficients contribute to the distinctive structural features, evidencing relatively stable morphological configurations and higher irradiation resistance in GaAs. Consequently, special optoelectronic properties associated with structural discrepancies facilitate the design and optimization of material functionalities by irradiation technologies.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Achieving ultrahigh modulus of resilience and enhanced thermal stability in ZnO x /SU-8 interpenetrating network polymer nanocomposite nanopillars

The modulus of resilience, a mechanical property that quantifies the maximum strain energy density a material can store during elastic deformation, is a crucial parameter for materials used in flexible displays, micro/nano-electro-mechanical system (M/NEMS) actuators, and ultra-sensitive pressure sensors. In this study, ZnO x /SU-8 nanocomposite nanopillars with a diameter of 300 nm, fully infiltrated with a uniformly distributed, interpenetrating amorphous ZnO x filler network, were synthesized via vapor-phase infiltration (VPI). In-situ uniaxial nano-compression tests revealed that the modulus of resilience of ZnO x /SU-8 reaches ∼ 12 MJ/m 3 , which is an ultrahigh value among all engineering materials with comparable strength. In addition, the synthesis fidelity, inorganic infiltration depth, and mechanical performance were all significantly improved compared to VPI-synthesized AlO x nanocomposites. Thermal stability, another key requirement for M/NEMS device materials operating under extreme environments, was also notably enhanced. Furthermore, partial crystallization of the amorphous ZnO x fillers during annealing contributed to an additional increase in modulus of resilience, reaching up to ∼ 13.9 MJ/m 3 . This work presents an effective fabrication strategy for producing nanostructured organic–inorganic hybrid nanocomposites with ultrahigh modulus of resilience and superior thermal stability, paving the way for their integration into next-generation flexible displays and high-performance M/NEMS devices working under harsh environments.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Local damage in grain boundary stabilized nanocrystalline aluminum

The excess free volume in grain boundaries of pure nanocrystalline aluminum leads to the grain coarsening, which degrades their desirable mechanical properties. The preferential segregation of dopants to the grain boundaries has been proposed to enhance the stability of the nanostructure. Here, to shed light on the stabilization mechanisms, we present results from virtual mechanical tests on nanocrystalline aluminum samples with similar grain sizes but different magnesium dopant contents. The segregation of magnesium decreases the excess free volume within the grain boundaries and prohibits the nucleation and growth of intergranular cracks.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Location and characterization of heterogeneous phases within Mary Rose wood

Preserving the Mary Rose oak hull for future generations is a major challenge due to the highly heterogeneous nature of waterlogged wooden artifacts, which contain polycrystalline, amorphous, and nanostructured materials that test traditional characterization methods. Effective conservation requires detailed knowledge of the distribution and chemical nature of these species to develop strategies for preventing multiple chemo-mechanical degradation pathways. Here, we apply synchrotron-based computed tomography total scattering methods to the Mary Rose keelson wood that provides valuable position-resolved structural information on multiple embedded species of different length and concentration scales. We identify 5 nm zinc sulfide nanoparticles in the wood, presumably deposits from bacteria operating on the sulfur energy cycle under the anaerobic conditions on the seabed. These are identified as precursors to acid attack on the wood upon removal to an aerobic environment. These insights inform not only next-generation conservation strategies, but also the efficacy and unforeseen issues of previous treatments.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

A general flame aerosol route to high-entropy nanoceramics

High-entropy ceramics are an emerging class of materials with fascinating characteristics. However, elemental immiscibility and crystal complexity limit the development of a general synthesis strategy, and common methods yield bulk materials. Here, we introduce a transformative non-equilibrium flame aerosol technique for synthesizing high-entropy nanoceramics. This scalable, one-step process enables the production of high-entropy oxide nanoceramics with an unprecedented diversity of crystal structures, including fluorite-phase materials that integrate up to 22 distinct cation elements. The method’s capacity for entropic stabilization and grain refinement significantly improves the thermal stability of these nanostructures. In a representative application, a Pt-(MgCoNiCuZn)O high-entropy single-atom catalyst showed superior activity and long-term stability, maintaining constant CO 2 conversion over 670 h and dramatically outperforming conventional catalysts. Finally, the general approach opens a vast composition and structure space for the creation of high-entropy oxide nanomaterials for application across diverse fields, including catalysis, energy storage, sensing, and thermal management.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Magnetically recyclable nanocomposites via lanthanide-based MOFs grown on natural sea sponge: Screening hydrogenation of nitrophenol to aminophenol

Catalysts have played a significant role in chemical industries and received significant attention as a result. Unfortunately, many common catalytic systems are comprised of a small number of elemental species or use similar synthetic strategies, which potentially limit innovation in areas such as the discovery of new transformations. Metal-organic frameworks (MOFs) have been established as versatile materials employed in various applications that include catalysis; however, the majority of MOFs have been synthesized using transition metal building blocks, possibly hindering advances towards innovative materials with unique properties. Here this work reports the synthesis of MOFs based on lanthanide elements (Ln = Ce, Gd, La, and Sm), which demonstrate great potential yet are often overlooked. The Ln-based MOFs were grown in situ on natural sea sponge supports and Fe ion containing solution, followed by a thermal carbonization treatment to generate FeLn metal nanoparticles (NPs) embedded on carbon support (FeLn@C). These nanostructured products exhibited good crystallinity and well-confined particle sizes. We then demonstrate that these hybrid materials can be used as effective heterogeneous nanocatalysts for the hydrogenation of nitrophenol to aminophenol in aqueous media. Besides, FeLn@C catalysts had a magnetic property due to Fe atoms in the NPs, which can be mechanically separated out from the aqueous solution since the catalysts are magnetically attracted to the external magnets. This magnetic recyclability combined with the usage of the natural materials highlight the importance of sustainability in the design of Ln-based MOFs and their catalytic applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Scalable synthesis of ultrathin MoS 2 membranes for dye desalination

Molybdenum disulfide (MoS 2 ) has been fabricated into thin-film composite (TFC) membranes for dye desalination due to its excellent underwater stability and tunable interlay spacing. However, it remains challenging to synthesize thin layers of MoS 2 with high water permeance and high dye rejection due to the difficulty in fabricating large crystalline sheets or exfoliation. Herein, we report a scalable method coupling bottom-up hydrothermal synthesis and top-down ultrasonic exfoliation to obtain well-dispersed MoS 2 nanosheets and a vacuum filtration method to prepare ultrathin membranes (thickness: 30 – 60 nm) for dye desalination. The MoS 2 nanosheets and membranes are thoroughly characterized for their chemistries and nanostructures. The membrane with 60-nm MoS 2 exhibits water permeance of 32 LMH/bar, Na 2 SO 4 rejection of 2.3%, and Direct Red-80 rejection of 99.0%. The MoS 2 membranes exhibit dye desalination performance superior to state-of-the-art commercial polyamide membranes and many leading membranes based on two-dimensional materials.

Dye desalination↗