Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “meter, test”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

Performance of a ballute decelerator towed behind a jet airplane

An F-104B airplane was modified to investigate the drag and stability characteristics of a ballute decelerator in the wake of an asymmetrical airplane. Decelerator deployments were initiated at a Mach number of 1.3 and an altitude of 15,240 meters (50,000 feet) and terminated when the airplane had decelerated to a Mach number of 0.5. The flight tests indicated that the decelerator had a short inflation time with relatively small opening forces. The drag levels attained with the subject decelerator were less than those obtained with other high-speed decelerators behind a symmetrical tow vehicle. The ballute demonstrated good stability characteristics behind the testbed airplane.

Pyle, J. S.↗

A forward speed effects study on jet noise from several suppressor nozzles in the NASA/Ames 40- by 80-foot wind tunnel

A test program was conducted in a 40 by 80 foot wind tunnel to evaluate the effect of relative velocity on the jet noise signature of a conical ejector, auxiliary inlet ejector, 32 spokes and 104 tube nozzle with and without an acoustically treated shroud. The freestream velocities in the wind tunnel were varied from 0 to 103.6 m/sec (300 ft/sec) for exhaust jet velocities of 259.1 m/sec (850 ft/sec) to 609.6 m/sec (2000 ft/sec). Reverberation corrections for the wind tunnel were developed and the procedure is explained. In conjunction with wind tunnel testing the nozzles were also evaluated on an outdoor test stand. The wind tunnel microphone arrays were duplicated during the outdoor testing. The data were then extrapolated for comparisons with data measured using a microphone array placed on a 30.5 meter (100 ft) arc. Using these data as a basis, farfield to nearfield arguments are presented with regards to the data measured in the wind tunnel. Finally, comparisons are presented between predictions made using existing methods and the measured data.

Beulke, M. R.↗

Low speed wind tunnel investigation of the aerodynamic and acoustic performance of several sonic inlet takeoff and approach geometries

A series of tests was conducted to determine the aerodynamic and acoustic performance of several sonic inlet takeoff and approach geometries. The effects of inlet lip shape and diffuser length were also investigated. The tests were conducted in a low-speed wind tunnel at free-stream velocities of 0 and 45 meters per second. Inlet incidence angle was varied from 0 deg to 50 deg. The inlets were sized to fit a 13.97-centimeter-diameter fan. In terms of the highest level of inlet total pressure recovery for a given amount of noise suppression, a cylindrical centerbody takeoff geometry and a bulb-shaped centerbody approach geometry provided the best results over all conditions of free-stream velocity and incidence angle. Increasing inlet lip contraction ratio extended the maximum incidence angle for attached lip flow, while increasing inlet diffuser length resulted in a higher total pressure recovery for a given amount of noise suppression.

Abbott, J. M.↗

Effects of wing leading-edge radius and Reynolds number on longitudinal aerodynamic characteristics of highly swept wing-body configurations at subsonic speeds

An investigation was conducted in the Langley low turbulence pressure tunnel to determine the effects of wing leading edge radius and Reynolds number on the longitudinal aerodynamic characteristics of a series of highly swept wing-body configurations. The tests were conducted at Mach numbers below 0.30, angles of attack up to 16 deg, and Reynolds numbers per meter from 6.57 million to 43.27 million. The wings under study in this investigation had leading edge sweep angles of 61.7 deg, 64.61 deg, and 67.01 deg in combination with trailing edge sweep angles of 0 deg and 40.6 deg. The leading edge radii of each wing planform could be varied from sharp to nearly round.

Henderson, W. P.↗

Use of LANDSAT-1 data for the detection and mapping of saline seeps in Montana

The author has identified the following significant results. April, May, and August are the best times to detect saline seeps. Specific times within these months would be dependent upon weather, phenology, and growth conditions. Saline seeps can be efficiently and accurately mapped, within resolution capabilities, from merged May and August LANDSAT 1 data. Seeps were mapped by detecting salt crusts in the spring and indicator plants in the fall. These indicator plants were kochia, inkweed, and foxtail barley. The total hectares of the mapped saline seeps were calculated and tabulated. Saline seeps less than two hectares in size or that have linear configurations less than 200 meters in width were not mapped using the LANDSAT 1 data. Saline seep signatures developed in the Coffee Creek test site were extended to map saline seeps located outside this area.

May, G. A.↗

Optical fiber dispersion characterization study

The theory, design, and results of optical fiber pulse dispersion measurements are considered. Both the hardware and software required to perform this type of measurement are described. Hardware includes a thermoelectrically cooled injection laser diode source, an 800 GHz gain bandwidth produce avalanche photodiode and an input mode scrambler. Software for a HP 9825 computer includes fast Fourier transform, inverse Fourier transform, and optimal compensation deconvolution. Test set construction details are also included. Test results include data collected on a 1 Km fiber, a 4 Km fiber, a fused spliced, eight 600 meter length fibers concatenated to form 4.8 Km, and up to nine optical connectors.

Geeslin, A.↗

Experimental studies on two dimensional shock boundary layer interactions

Experiments have been performed on the interaction of oblique shock waves with flat plate boundary layers in the 30.48 cm x 30.48 cm (1 ft. x 1 ft.) supersonic wind tunnel at NASA Lewis Research Center. High accuracy measurements of the plate surface static pressure and shear stress distributions as well as boundary layer velocity profiles were obtained through the interaction region. Documentation was also performed of the tunnel test section flow field and of the two-dimensionality of the interaction regions. The findings provide detailed description of two-dimensional interaction with initially laminar boundary layers over the Mach number range 2.0 to 4.0. Additional information with regard to interactions involving initially transitional boundary layers is presented over the Mach number range 2.0 to 3.0 and those for initially turbulent boundary layers at Mach 2.0. These experiments were directed toward providing well documented information of high accuracy useful as test cases for analytic and numerical calculations. Flow conditions encompassed a Reynolds number range of 4.72E6 to 2.95E7 per meter. The shock boundary layer interaction results were found to be generally in good agreement with the experimental work of previous authors both in terms of direct numerical comparison and in support of correlations establishing laminar separation characteristics.

Skebe, S. A.↗

Sidewall boundary-layer measurements with upstream suction in the Langley 0.3-meter transonic cryogenic tunnel

The Langley 0.3 Meter Transonic Cryogenic Tunnel has provision for boundary removal from the sidewalls to reduce sidewall interference effects on the test data. The tests carried out to determine the change in the empty test section sidewall boundary layer thickness at the model station with upstream boundary layer mass removal are described. The boundary layer measurements showed that the upstream removal region is effective in reducing the boundary layer thickness at the model station. The boundary layer displacement thickness reduced from about 1.2 percent to about .4 percent of the test section width. The boundary layer velocity profiles followed a power law variation in the outer region and showed good correlation when plotted in terms of boundary layer momentum thickness.

Murthy, A. V.↗

Aircraft Speed Instruments

This report presents a concise survey of the measurement of air speed and ground speed on board aircraft. Special attention is paid to the pitot-static air-speed meter which is the standard in the United States for airplanes. Air-speed meters of the rotating vane type are also discussed in considerable detail on account of their value as flight test instruments and as service instruments for airships. Methods of ground-speed measurement are treated briefly, with reference to the more important instruments. A bibliography on air-speed measurement concludes the report.

Beij, K Hilding↗

Measurement Instruments

International Technology Corporation (INTEC) manufactures a line of instruments used for determining the optical properties of materials used in solar energy applications. Some of INTEC's instruments are based on NASA technology, including the Willey Alpha Meter and McDonald Emissometer. The emissometer is a commercial version of a system developed by Lewis Research Center to test efficiency- increasing coatings on solar panels. These instruments are used by manufacturers of solar equipment, government, university and private laboratories.

Source record↗

Swift: A Gamma Ray Bursts Explorer

Swift is a NASA gamma-ray burst MIDEX mission that is in development for launch in December 2003. It is a multiwavelength transient observatory for GRB astronomy. The goals of the mission are to determine the origin of GRBs and their afterglows and use bursts to probe the early Universe. It will also.perform a survey of the hard X-ray sky to a sensitivity level of -1 mCrab. A wide-field camera will detect more than a hundred GRBs per year to 5 times fainter than BATSE. Sensitive narrow-field X-ray and UV/optical telescopes will be pointed at the burst location in 20 to 70 sec by an autonomously controlled 'swift' spacecraft. For each burst, arcsec positions will be determined and optical/UV/X-ray/gamma-ray spectrophotometry performed. Measurements of redshift will be made for many of the bursts. The instrumentation is a combination of superb existing flight-spare hardware and design from XMM and Spectrum-X/JET-X contributed by collaborators in the UK and Italy and development of a coded-aperture camera with a large-area (approximately 0.5 square meter) CdZnTe detector array. The hardware is currently in final stages of fabrication and initial stages of integration and test. Key components of the mission are vigorous follow-up and outreach programs to engage the astronomical community and public in Swift.

Gehrels, Neil↗

Measurements on Compressor-Blade Lattices

At the end & 1940 an investigation of a guide-vane lattice for the compressor of a TL unit [NACA comment: Turbojet] was requested. The greatest possible Mach number had to be attained. The investigation was conducted with an annular lattice subjected to axial flow. A direct-current shunt motor with a useful output of 235 horsepower at en engine speed of 1800 qm was available for driving the necessary blower. In designing the blower the speed was set at 10,000 rpm. A gear box fran an armored car was used as gearing in which supplementary fresh oil lubrication was installed. The gear box was used to step up from low to high speeds. The blower that was designed is two stage. The hub-tip ratios are 0.79 to 0.82; the design pressure coefficient for each stage is 0.6 and the design flow coefficient is 0.4. The rotor dosimeter D sub a is 0.39 meters and the resulting peripheral speed is u sub a = 204 meters per second [NACA comment: Value corrected from the German]. The blower was entirely satisfactory. The construction of the test stand is shown in figure 1. The air flows in through an annular Inlet, which is used in the measurement of the quantity of air, and is deflected into an inward-pointing radial slot. A spiral motion is imparted to the air by a guide-vane installation manually adjustable as desired, which enables injection of the air, after it has been deflected from the radial direction to the axial direction, into the lattice being investigated at any desired angle.

Weinig, F.↗

Precise Truss Assembly using Commodity Parts and Low Precision Welding

We describe an Intelligent Precision Jigging Robot (IPJR), which allows high precision assembly of commodity parts with low-precision bonding. We present preliminary experiments in 2D that are motivated by the problem of assembling a space telescope optical bench on orbit using inexpensive, stock hardware and low-precision welding. An IPJR is a robot that acts as the precise "jigging", holding parts of a local assembly site in place while an external low precision assembly agent cuts and welds members. The prototype presented in this paper allows an assembly agent (in this case, a human using only low precision tools), to assemble a 2D truss made of wooden dowels to a precision on the order of millimeters over a span on the order of meters. We report the challenges of designing the IPJR hardware and software, analyze the error in assembly, document the test results over several experiments including a large-scale ring structure, and describe future work to implement the IPJR in 3D and with micron precision.

Komendera, Erik↗

Development and Short-Range Testing of a 100 kW Side-Illuminated Millimeter-Wave Thermal Rocket

The objective of the phase described here of the Millimeter-Wave Thermal Launch System (MTLS) Project was to launch a small thermal rocket into the air using millimeter waves. The preliminary results of the first MTLS flight vehicle launches are presented in this work. The design and construction of a small thermal rocket with a planar ceramic heat exchanger mounted along the axis of the rocket is described. The heat exchanger was illuminated from the side by a millimeter-wave beam and fed propellant from above via a small tank containing high pressure argon or nitrogen. Short-range tests where the rocket was launched, tracked, and heated with the beam are described. The rockets were approximately 1.5 meters in length and 65 millimeters in diameter, with a liftoff mass of 1.8 kilograms. The rocket airframes were coated in aluminum and had a parachute recovery system activated via a timer and Pyrodex. At the rocket heat exchanger, the beam distance was 40 meters with a peak power intensity of 77 watts per square centimeter. and a total power of 32 kilowatts in a 30 centimeter diameter circle. An altitude of approximately 10 meters was achieved. Recommendations for improvements are discussed.

Bruccoleri, Alexander↗

NASA's Interests in Bioregenerative Life Support

NASA and other space agencies and around the world have had long-standing interest in using plants and biological approaches for regenerative life support. In particular, NASA's Kennedy Space Center, has conducted research in this area for over 30 years. One unique aspect to this testing was NASA's Biomass Production Chamber, which had four vertically stacked growing shelves inside a large, 113 cubic meter chamber. This was perhaps one of the first working examples of a vertical agriculture system in the world. A review of some of this research along with some of the more salient findings will be presented.

Wheeler, Raymond M.↗

Development of an In-Situ Decommissioning Sensor Network Test Bed for Structural Condition Monitoring - 12156

The Savannah River National Laboratory (SRNL) has established an In Situ Decommissioning (ISD) Sensor Network Test Bed, a unique, small scale, configurable environment, for the assessment of prospective sensors on actual ISD system material, at minimal cost. The Department of Energy (DOE) is presently implementing permanent entombment of contaminated, large nuclear structures via ISD. The ISD end state consists of a grout-filled concrete civil structure within the concrete frame of the original building. Validation of ISD system performance models and verification of actual system conditions can be achieved through the development a system of sensors to monitor the materials and condition of the structure. The ISD Sensor Network Test Bed has been designed and deployed to addresses the DOE-Environmental Management Technology Need to develop a remote monitoring system to determine and verify ISD system performance. Commercial off-the-shelf sensors have been installed on concrete blocks taken from walls of the P Reactor Building at the Savannah River Site. Deployment of this low-cost structural monitoring system provides hands-on experience with sensor networks. The initial sensor system consists of groutable thermistors for temperature and moisture monitoring, strain gauges for crack growth monitoring, tilt-meters for settlement monitoring, and a communication system for data collection. Baseline data and lessons learned from system design and installation and initial field testing will be utilized for future ISD sensor network development and deployment. The Sensor Network Test Bed at SRNL uses COTS sensors on concrete blocks from the outer wall of the P Reactor Building to measure conditions expected to occur in ISD structures. Knowledge and lessons learned gained from installation, testing, and monitoring of the equipment will be applied to sensor installation in a meso-scale test bed at FIU and in future ISD structures. The initial data collected from the sensors installed on the P Reactor Building blocks define the baseline materials condition of the P Reactor ISD external concrete structure. Continued monitoring of the blocks will enable evaluation of the effects of aging on the P Reactor ISD structure. The collected data will support validation of the material degradation model and assessment of the condition of the ISD structure over time. The following are recommendations for continued development of the ISD Sensor Network Test Bed: - Establish a long-term monitoring program using the concrete blocks with existing sensor and/or additional sensors for trending the concrete materials and structural condition; - Continue development of a stand-alone test bed sensor system that is self-powered and provides wireless transmission of data to a user-accessible dashboard; - Develop and implement periodic NDE/DE characterization of the concrete blocks to provide verification and validation for the measurements obtained through the sensor system and concrete degradation model(s). (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Automated gas burette system for evolved hydrogen measurements

This paper reports a simple and efficient gas burette system that allows automated determination of evolved gas volume in real time using only temperature and pressure measurements. The system is reliable and has been used successfully to study the hydrogen release kinetics of ammonia borane thermolysis. The system is especially suitable for bench scale studies involving small batches and potentially rapid reaction kinetics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Quantitative Daily Maps of PM 2.5 Episodes for California and Other Regions: Satellite Column Water and Optical Depth as Allied Tracers of Dilution

The Western US and many regions globally present daunting difficulties in understanding PM 2.5 episodes. We evaluate extensions of a method independent of modeled source-description and transport/transformation and using several satellite remote sensing products from imaging spectrometers. The San Joaquin Valley (SJV) especially suffers few-day episodes due to shallow mixing; PM 2.5 retrieval suffers low satellite AOT (Aerosol Optical Thickness) and bright surfaces.Nevertheless, we find residual errors in our maps of of typically 5-8 micrograms per cubic meter. Episodes in the Valley reaching 60-100 micrograms per cubic meter. These maps detail pollution from Interstate 5 at the scale of a few kilometers. The maps are based on NASA's MODerate resolution Imaging Spectrometer (MODIS) data at circa 1 kilometer as processed with the Multi-Angle Implementation of Atmospheric Correction. The Bay Area Air Quality Management District has requested that we test our methods in their challenging environment characterized by multiple sub-basins defined by complex topography. Our tests suggest that nearly similar precision may be expected for wintertime conditions with high PM 2.5 . We note difficulties when measured PM 2.5 is less than 8-10 micrograms per cubic meter, but good relative precision when PM 2.5 rises above 20; i.e. in episodes of concern for morbidity and mortality. Our method stresses physically meaningful functions of MODIS-MAIAC (Multi-Angle Implementation of Atmospheric Correction)-derived AOD (Aerosol Optical Depth) and total water vapor column. A mixed-effects statistical model exploiting existing station data works powerfully to allow us daily AOT-to-PM 2.5 relationships that allow a calibration of the map. In those cases where water vapor and particles have generally similar surface sources, using the ratio of AOT / Column_water can improve the daily calibrations so as to reach our quoted precision. We briefly present some cartoon idealizations that explain this success and also the likely reasons that our mixed effects model (or "daily calibration") works; also when it should not work. The combined satellite/mixed-effects model works best for wintertime San Joaquin Valley episodes, where the meteorology of particle and H2O(v) dilution is quite appropriate. We extended and tested the methodology (a) for the Bay Area wintertime situations and (b) for smoke plume events (e.g. the October 2017 fire events of the Sonoma area). Our SJV work was evaluated using NASA's DISCOVER-AQ (Deriving Information on Surface conditions from Column and Vertically Resolved Observations Relevant to Air Quality) airborne measurements, and by season- long measurements in Fresno. If the composition and size distribution of the aerosols can be assessed for the regions we describe, retrievals should have improved accuracy.

Chatfield, Robert B.↗