Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “mechanical”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Mechanical and Thermal Characterization of Additively Manufactured Carbon/Nylon 12 and Carbon/PEEK Composites

This study explores additive manufacturing of carbon fiber-reinforced thermoplastic composites using the Composite-Based Additive Manufacturing (CBAM) process. Carbon/Nylon 12 and Carbon/PEEK composites were fabricated and evaluated through mechanical (compression, tensile, flexural, and impact) and thermal (DSC and TGA) tests. Carbon/PEEK exhibited superior mechanical performance, with 97.5% higher tensile strength, 79.8% higher elastic modulus, and 59.6% higher flexural strength compared to Carbon/Nylon 12. Thermal testing showed that Carbon/PEEK had higher thermal stability, beginning degradation at 350 °C versus 298 °C for Carbon/Nylon. These results indicate that CBAM-fabricated Carbon/PEEK composites are suitable for applications requiring high strength and temperature resistance.

Additive manufacturing↗
DOE OSTI2020

Corrosion and Mechanical Performance of Grade 92 Ferritic-Martensitic Steel After Exposure to Supercritical Carbon Dioxide

Grade 92 ferritic-martensitic steel is a candidate alloy for medium temperature (< 550 °C) components for the supercritical carbon dioxide (s-CO 2 ) Brayton cycle. 1000 hours exposures were performed on base and welded material in s-CO 2 at temperatures of 450 °C or 550 °C and compared to samples aged in Ar at 550 °C. Both s-CO 2 exposures resulted in a duplex oxide growth and carburization, with 450 °C exhibiting carburization in a power law diffusion profile up to a depth of 200-250 µm, while 550 °C showed a linear profile up to a depth of 100 µm. The different profiles indicate much slower precipitation and coarsening of carbides at the lower temperature, allowing carbon to diffuse deeper into the material. However, 450 °C produced improved mechanical properties while 550 °C produced deteriorated properties. This was due to the higher density of carbon near the metal–oxide interface which leads to significant carbide coarsening and, subsequently, crack initiation and early failure. Finally, additional exposure at 450 °C is predicted to increase deposited carbon, but further study would be needed to understand if and when carburization will produce a negative mechanical effect.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A Mechanism for Carbon Depletion at Bondline of High-Frequency Electric-Resistance-Welded X70 Pipeline Steel

The bondline of electric-resistance-welded (ERW) linepipe steel, often etched white (i.e., ferrite) in optical microscopy, is generally believed to be carbon depleted. The mechanism for the carbon depletion, however, is not fully understood by researchers. To this end, here we used atom probe tomography (APT) to measure elemental segregation of the as-welded and post-weld heat-treated bondline regions of X70 linepipe welds. The thin vertical features at the bondline in the as-welded condition were identified as carbon-rich martensite-austenite (M-A) constituents, and the majority ferrite phase in the bondline was identified as carbon-depleted ferrite. Following the post-weld normalization, all alloying elements, except Nb and Mo, are homogenized across the bondline and heat-affected zone. The carbon depletion in the ERW bondline was accurately measured. A new mechanism for carbon depletion has been proposed using Scheil calculations of elemental partitioning during weld formation. Segregation of elements in the heat-affected zone was shown to follow the negligible partitioning local equilibrium (NPLE) kinetics for bainite transformation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Temperature-Dependent Thermal and Mechanical Properties of a Wire Arc Additively Manufactured Low Transformation Temperature Steel

Recent research has studied the use of low transformation temperature (LTT) martensite steel as feedstock for wire arc additive manufacturing (WAAM) and low tensile residual stresses or compressive residual stresses were detected in the printed walls. These residual stress states help to improve printed product properties such as fatigue strength and corrosion resistance. However, the thermal and mechanical properties of WAAM printed LTT martensite steel walls are largely unknown. In this work, a printed LTT martensite steel was characterized for its thermal, metallurgical, and mechanical behavior at room and elevated temperatures. The temperature-dependent specific heat capacity, thermal expansion, atomic lattice spacing, and tensile properties were measured during both heating and cooling and related to observed microstructural features and computational thermodynamics predictions. These results revealed a large hysteresis in the martensitic transformation, with a martensite start temperature of 240 °C and austenite start temperature of 680 °C. Additional thermal cycles and specimen orientation did not affect the printed specimen austenite and martensite transformations. However, it was observed that the printed metal may exhibit tempering embrittlement at about 350 °C but further studies are needed to confirm that. Further, these results suggest that a temperature control of 250 °C to 350 °C during WAAM is needed to maximize the stress reduction potential of the LTT250 martensite steel. Opportunities for future implementation of LTT martensite steels and optimization of additive manufacturing process conditions are identified.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Investigation on the Surface Vortex Formation During Mechanical Stirring with an Axial-Flow Impeller Used in an Aluminum Process

The present study investigated the mechanism of surface vortex formation in an aluminum melt vessel stirred by an axial-flow impeller mechanically. The oxide film is formed at the aluminum melt/air interface, and the movement of the interface entrains the oxide film and inclusions. Hence, the transient movement of melt–air interface is significant. The present study conducted a water model experiment and numerical simulation focusing on the movement of gas–liquid interface. The present study found that the oxide film can be entrained by two phenomena: (1) local surface vortex and (2) sloshing near the vessel wall. The local surface vortex is formed due to the pressure distribution around the impeller, and the sloshing is caused by macroinstabilities, which is generated by the discharged flow of axial-flow impeller. Besides, the shape of gas–liquid interface is dependent on the impeller shape. The axial-flow impeller gives rise to steeply curved shape of gas–liquid interface near the impeller shaft.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Grain Boundary and Lattice Fracture Toughness of UO 2 Measured Using Small-Scale Mechanics

Small-scale mechanical testing has been used to isolate the properties of individual grain boundaries and regions of the lattice in undoped UO 2 polycrystals. Notched microcantilever specimens were prepared by focused ion beam milling and tested in bending. Fracture toughness values were calculated from finite element analysis of the sample geometry at fracture load using the J-integral method. Lattice and grain boundary fracture toughness values of 1.17 ± 0.16 MPa m 1/2 and 1.08 ± 0.08 MPa m 1/2 , respectively, were obtained. The similarity between the lattice and grain boundary fracture toughness values is consistent with the preference for transgranular room-temperature fracture in UO 2 . The grain boundary and lattice fracture toughness values also agree well with the toughness of dense polycrystals, which suggests that microstructural-scale toughening mechanisms are limited in such samples.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Deformation Mechanism Transition in Additively Manufactured Compositionally Graded Fe-Base Alloys

Microstructure-dependent deformation and fracture behavior was investigated for an additively manufactured compositionally graded alloy (CGA) printed using the laser-directed energy deposition (L-DED) method to explore an alternative approach for dissimilar metal joints in nuclear energy systems. The electron backscatter diffraction (EBSD) maps from scanning electron microscopy (SEM) display a clear microstructural transition with decreasing austenite-forming elements (Ni and Mn), from an austenite (γ) dominant structure, to a complex composite structure containing ferrite (α), martensite (α') and retained austenite, and then to a fully ferritic structure. EBSD data were recorded in situ during tensile testing in SEM, and the evolution of the deformation mechanism and microstructure was characterized using Kikuchi diffraction pattern analysis. Complementary analysis for high-resolution features was also performed using scanning transmission electron microscopy (STEM). The Ni/Mn-rich austenite-dominant microstructures showed a complex deformation mechanism of two-step martensitic transformation (γ→ε→α'), whereas the minor austenite phase retained in the ferrite and/or martensite matrix showed a single transformation route (γ→α'). Ordinary dislocation glide and twinning via partial dislocation glide were observed in the austenite deformation. Meanwhile, the ferrite and martensite grains deformed mainly by ordinary dislocation slips and grain rotation. Furthermore, static tensile fracture was also highly dependent on local composition and phase constituents.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Enhanced Mechanical Properties and Wear Resistance of FeCrAl Alloys at ~ 300°C and Higher Temperatures

Abstract Worldwide, light water reactors (LWRs) have been using zirconium (Zr)-based alloys for the cladding of the uranium dioxide fuel for more than 6 decades. Zr alloys oxidize rapidly in the presence of water and steam at temperatures > 450°C; therefore, they do not respond well to scenarios of loss of coolant accidents. There is a global effort by nuclear materials technologists to find more robust or stronger cladding materials for LWRs. One option is to use an iron-chromium-aluminum (FeCrAl) alloy since they have excellent resistance to high temperature oxidation and superior mechanical properties at LWR operation temperatures. Results show that (1) FeCrAl alloys have better mechanical properties than Zr alloy and are orders of magnitude more resistant to creep at temperatures higher than LWR normal operation conditions. (2) FeCrAl alloys have better resistance to fretting wear than Zr alloys at the normal operation conditions of LWRs.

Materials Science↗
DOE OSTI2024

Review of Solid State Consolidation Processing Techniques of ODS Steels (Hot Extrusion, Hot Isostatic Pressing, Spark Plasma Sintering, and Stir Friction Consolidation): Resulting Microstructures and Mechanical Properties

This paper reviews the solid-state consolidation processing techniques for Oxide Dispersion Strengthened steels and compares them in terms of the resulting microstructure and reported mechanical properties. Synthesis techniques include hot extrusion, hot isostatic pressing, spark plasma sintering and friction consolidation. The effects of process parameters on the resulting microstructures and performance are discussed for each technique. Average oxide size, average grain size, and porosity are compared across techniques, as well as mechanical strength and ductility. Across consolidation techniques where temperature can be controlled, a low sintering temperature with a high sintering pressure is favorable for keeping oxide sizes, grain sizes, and porosity low. The use of yttrium and titanium for oxide formation has been evidenced to reduce oxide sizes, and tungsten additions have been shown to improve strength. Current literature suggests that the more mature hot extrusion technique produces stronger steel with consistently fine oxides, while other alternative solid-state consolidation, while promising, offer margin for improvement.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Investigation of Remanufacturing Methods Utilizing Mechanically-Generated and Gas-Atomized Feedstock Production for Directed Energy Deposition Processing Through Specific Energy Consumption Modeling

The goal of this work was to assess the energy consumption of a novel remanufacturing method that utilizes mechanically-generated feedstock for directed energy deposition. Gas-atomization is the state-of-the-art production process for directed energy deposition feedstock, and for this work was incorporated into a remanufacturing process path to provide a comparison method. Specific energy consumption models of remanufacturing utilizing both of these proposed process paths were developed and applied to a case study to investigate energy saving opportunities for future manufacturing paradigms. The energy modelling was done in three stages. First, the mechanically-generated feedstock production energy consumption model was generated from experimental observation. Second, the gas-atomized feedstock production energy consumption model was generated from a combination of experimental observation, reported estimates from the manufacturer, and data found in the literature. Lastly, the energy consumption model of directed energy deposition was derived from experimental observation and compares favorably with reported estimates in the literature. With the models, the specific energy consumption in the two process paths were compared and their application was demonstrated by estimating the energy consumption to remanufacture a bracket. The two feedstock production methods had similar specific energy consumptions. The specific energy consumption of the directed energy deposition process was the greatest component in the respective remanufacturing paths by an order of magnitude; increasing deposition rate is the most important factor for lowering the overall specific energy consumption. The analyzed remanufacturing technologies were estimated to consume less energy than replacement when repairing up to approximately 15% of the original part’s mass.

42 ENGINEERING↗
DOE OSTI2025

Structure-dependent mechanisms for plastic degradation in the marine environment

The visible and invisible accumulation of waste plastic in our oceans is a consequence of rapidly increasing inputs and very slow degradation rates. In general, this combination of effects results in long residence times. Nevertheless, the abiological degradation rate of a specific synthetic plastic varies widely, depending on its structural characteristics at the molecular, mesoscopic, and macroscopic levels. This chapter summarizes factors that determine these rates of degradation, and describes their principal mechanisms, for several of the major types of waste plastic found in the oceans. Mechanical forces cause cracking and flaking that break macroplastics into microplastics and even smaller fragments with increasing surface-to-volume ratios. Chemical degradation rates increase with surface area, influenced by intrinsic variations in crystallinity and the presence of additives, as well as extrinsic factors such as temperature, pH, and UV light intensity. Since polyolefin-based plastics are less dense than seawater and lack hydrolysable bonds in their polymer backbones, they accumulate close to the surface of the ocean where photo-oxidation is the principal cause of C–C bond cleavage in the polymer backbone. In contrast, polyesters and polyamides are denser than seawater and they sink, experiencing less exposure to solar irradiation. However, they can also degrade by slow hydrolysis of the C–O or C–N bonds intrinsic to the polymer structures.

Maciulis, Nicholas A.↗
DOE OSTI2020

Pyridoxal 5'-phosphate dependent reactions: Analyzing the mechanism of aspartate aminotransferase

Enzyme catalysis is the primary activity in energy and information metabolism and enzyme cofactors are key to the catalytic ability of most enzymes. Pyridoxal 5'-phosphate (PLP) cofactor, derived from Vitamin B6, is widely distributed in nature and has significant latitude in catalytic diversity. X-ray crystallography has revealed the structures of diverse PLP dependent enzymes from multiple families. But these structures are incomplete, lacking the positions of protons essential for understanding enzymatic mechanisms. Here, we review the diversity of PLP and discuss the use of neutron crystallography and joint X-ray/neutron refinement of Fold Type I aspartate aminotransferase to visualize the positions of protons in both the internal and external aldimine forms. Strategies used to prepare extremely large crystals required for neutron diffraction and the approach to data refinement including the PLP cofactor are discussed. The observed positions of protons, including one located in a previously unknown low-barrier hydrogen bond, have been used to create more accurate models for computational analysis. The results revealed a new mechanism for the transaminase reaction where hyperconjugation is key to reducing the energy barrier which finally provides a clear explanation of the Dunathan alignment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Mechanisms of Ti 3 Al precipitation in hcp α -Ti

Here, nucleation and growth of Ti3Al α( 2 ) ordered domains in alpha-Ti-Al-X alloys were characterised using a combination of transmission electron microscopy, atom probe tomography and small angle X-ray scattering. Model alloys based on Ti-7Al (wt.%) and containing O, V and Mo were aged at 550 °C for times up to 120d and the resulting precipitate dispersions were observed at intermediate points. Precipitates grew to around 30nm in size, with a volume fraction of 6-10% depending on tertiary solutes. Interstitial O was found to increase the equilibrium volume fraction of α 2 , while V and Mo showed relatively little influence. Addition of any of the solutes in this study, but most prominently Mo, was found to increase nucleation density and decrease precipitate size and possibly coarsening rate. Coarsening can be described by the Lifshitz-Slyozov-Wagner model, suggesting a matrix diffusion-controlled coarsening mechanism (rather than control by interfacial coherency). Solutionising temperature was found to affect nucleation number density with an activation energy of E f = 1.5 +/- 0.4 eV, supporting the hypothesis that vacancy concentration affects α 2 nucleation. The observation that all solutes increase nucleation number density is also consistent with a vacancy-controlled nucleation mechanism.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Revealing the effect of local stresses on twin growth mechanisms in titanium using synchrotron X-ray diffraction

Deformation twinning has a significant impact on the evolution of microstructure and mechanical response in hexagonal close packed (hcp) metals. Understanding the physical mechanisms associated with twin nucleation and growth processes is important to enable the broad use of hcp metals. While both nucleation and growth are conditioned by the local stress state, few studies have quantified it in bulk deformed samples. In this study, we reveal the effects of local stresses on twin thickening using in-situ synchrotron experiments with differential aperture X-ray microscopy. High purity Ti is deformed under four-point bending to activate {1012} tensile twins. Further, 3D stress fields with a spatial resolution of 0.5μm are mapped in the vicinity of low and high macroscopic Schmid factor (MSF) twins growing inside a grain. Reconciling this experimental analysis with recent twin growth models reveals that the growth of low MSF twins is limited by the nucleation of twin growth defects in the high-purity Ti sample. While growth-inducing defect nucleation may occur in many places on the interface of the high resolved shear stress (RSS)/MSF twin, the nucleation rate of twinning disconnections for the low MSF twin is high only at the end of the twin near a stress concentration. Once nucleated, these defects easily propagate into lower RSS regions of the grain resulting in twin growth. This work highlights the importance of stress concentrations not only for twin (embryo) nucleation, but also to the growth process of twins, particularly in low MSF twins.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Kink mechanism in Cu/Nb nanolaminates explored by $\mathcal{in}$ $\mathcal{situ}$ pillar compression

We report Nano metallic laminates (NMLs) exhibit different failure modes depending on the loading conditions due to their mechanical anisotropies. Kinking is a typical failure mode in many NMLs compressed along a layer-parallel direction. However, a detailed description of the microstructure evolution during kink band (KB) formation and an in-depth understanding of the formation mechanisms are lacking. In this work, the KB process is investigated in Cu/Nb NMLs by in situ micro pillar compression in the scanning electron microscope (SEM) along a layer-parallel direction. Post-mortem S/TEM and transmission Kikuchi diffraction (TKD) analyses show that kink banding leads to significant microstructure changes characterized by an accumulation of geometrically necessary dislocations (GNDs) and of tilt geometrically necessary boundaries (GNBs) near KB boundaries (KBBs). The distinct microstructure evolution implies that KB formation is facilitated by the inhomogeneous microstructures resulting in constrained deformation modes. Specifically, dislocations active on slip planes nearly parallel to the interfaces make a major contribution to kink evolution after the onset of kinking. Once layer-parallel slip systems are activated, preexisting lattice dislocations and dislocations nucleating from interfaces will accumulate as GNDs near KBBs via the stochastic storage of lattice dislocations that have certain Burgers vectors. GNDs can further transform into GNBs via cross-slip and climb driven processes near the KBB. Furthermore, GNBs near KBBs can grow by incorporating more GNDs or by coalescence to accommodate the KB evolution. We further hypothesize that microstructural perturbations and their ensuing stresses can initiate KB formation in Cu/Nb NMLs.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Investigation of twin growth mechanisms in precipitate hardened AZ91

Here, in this work, an elasto-viscoplastic fast-Fourier-transform (EVP-FFT) model with a dislocation-density (DD) based hardening law is employed to study the growth of a {10$\bar{1}$2} tensile twin that is blocked by basal-precipitates in precipitate-hardened AZ91 magnesium alloy. It is frequently reported that twin growth is hindered in precipitate-hardened Mg alloys; however, thick twin domains are often observed experimentally in these material systems. Detailed numerical investigation of deformation twinning starting from an early propagation stage, before twin growth, reveals that the stress fields that result from two sequentially propagated twins co-impinging on a precipitate relaxes the twin back stress locally and promotes twin growth at the twin-precipitate junction. Based on these findings, a two-step growth mechanism is proposed for twins arrested by precipitates. In the first step, the interaction of a twin tip with a precipitate develops a stress concentration on the other side of the precipitate, prompting the formation of a second twin. Subsequently, the back stresses associated with the first twin are relaxed by the formation of the second twin, allowing the first twin to grow at the twin-precipitate junction and eventually engulf the precipitate. This mechanism suggests that twin growth can be achieved locally with minimal additional external forces, explaining how relatively large twin domains can develop even in the presence of arrays of precipitates.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Elucidating grain boundary energy minimization mechanisms in textured Ca-doped alumina with inclination-dependent Monte Carlo Potts simulations

The grain growth behavior of textured Ca-doped alumina is compared to Monte Carlo Potts (MCP) simulations to investigate the effect of anisotropic grain boundary (GB) properties on local boundary migration. Experimentally, the growth of textured Ca-doped alumina results in highly elongated grains. The relative GB energy distribution is measured using the thermal groove method before and after heat treating at 1600°C, finding that high energy GBs are eliminated during grain growth. No significant difference in the GB energy distributions is found between the long and short axes of the elongated grains, suggesting that anisotropic mobility may be responsible for the grain shape. However, MCP simulations with anisotropic mobility as a function of plane inclination do not result in grains with distinct morphologies, regardless of the degree of anisotropy introduced. The final grain shape after grain growth of textured Ca-doped alumina resembles that of the MCP simulations using an anisotropic GB energy as a cosine function of plane inclination. Several energy functions are tested and only those that mathematically impose a torque (second derivative of energy with respect to the plane inclination angle) result in elongated grains. Although area reduction is the dominant energy minimization mechanism, these results suggest that local GB migration is affected by anisotropic GB energy and torque and alternative mechanisms like GB replacement and reorientation.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Effect of magneto-mechanical synergism in the process-structure correlation in Fe–C alloys: A phase-field modeling approach

Applied magnetic fields can alter phase equilibria and kinetics in steels; however, quantitatively resolving how magnetic, chemical, and elastic driving forces jointly influence the microstructure remains challenging. We develop a quantitative magneto-mechanically coupled phase-field model for the Fe–C system that couples a CALPHAD-based chemical free energy with demagnetization-field magnetostatics and microelasticity. Here, the model reproduces single- and multi-particle evolution during the α → γ inverse transformation at 1023 K under external fields up to 20 T, including ellipsoidal morphologies observed experimentally at 8 T. Chemically driven growth is isotropic; a magnetic interaction introduces an anisotropic driving force that elongates γ precipitates along the field into ellipsoids, while elastic coherency promotes faceting, yielding elongated cuboidal or “brick-like” particles under combined magneto-elastic coupling. Growth kinetics increase with C content, and decrease with field strength and misfit strain. Multi-particle simulations reveal dipolar interaction-mediated coalescence for field-parallel neighbors and ripening for field-perpendicular neighbors. Incorporating field-dependent diffusivity from experiment slows kinetics as expected; a first-principles-motivated anisotropic diffusivity correction is estimated to be small (<2%). These results establish a process-structure link for magnetically assisted heat treatments of Fe–C alloys and provide guidance for microstructure control via chemo-magneto-mechanical synergism.

Magnetic field↗