Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “jets”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

Analysis of the injection of a heated turbulent jet into a cross flow

The development of a theoretical model is investigated of the incompressible jet injection process. The discharge of a turbulent jet into a cross flow was mathematically modeled by using an integral method which accounts for natural fluid mechanisms such as turbulence, entrainment, buoyancy, and heat transfer. The analytical results are supported by experimental data and demonstrate the usefulness of the theory for estimating the trajectory and flow properties of the jet for a variety of injection conditions. The capability of predicting jet flow properties, as well as two- and three-dimensional jet paths, was enhanced by obtaining the jet cross-sectional area during the solution of the conservation equations. Realistic estimates of temperature in the jet fluid were acquired by accounting for heat losses in the jet flow due to forced convection and to entrainment of free-stream fluid into the jet.

Campbell, J. F.↗

Theory of an airfoil equipped with a jet flap under low-speed flight conditions

A theory is developed, for the inviscid, incompressible flow past a thin airfoil equipped with a thin, part-span jet flap, by treating the induced flowfields of the jet and the wing separately and by obtaining the fully coupled solution in an iterative manner. Spanwise variation of the jet vortex strength is assumed to be elliptical in the analysis. Since the method considers the vorticity associated with the jet to be positioned on the computed locus of the jet, the downwash aft of the wing is evaluated as well as forces and moments on the wing. A lifting-surface theory is incorporated for the aerodynamics of the wing. Computational results are presented for a rectangular wing at momentum coefficients above 2.0 and compared with existing linear theories and experimental data. Good agreement is found for small angles of attack, jet-deflection angles, and jet-momentum coefficients where the linear theories and experimental data are applicable. Downwash data at a point in the vicinity of a control surface, the load distribution on the airfoil, and the jet, and the jet location are also presented for representative flight conditons.

Addessio, F. L.↗

An experimental study of a jet issuing from a lifting wing

An experimental program was conducted to determine the behavior of a round turbulent jet issuing from a lifting two-dimensional wing in crossflow. The jet was located at 65% wing chord on an NACA 0021 airfoil fitted with a 30% chord NACA 4415 flap. The flowfield associated with the jet was surveyed extensively with directional pressure probes to determine local velocity vectors and pressures for three different values of lift coefficient at jet effective velocity ratios (square root of the ratio of the jet dynamic pressure to the freestream dynamic pressure) of 4, 6, and 8. Data describing the jet centerline and the path of the contrarotating vortices accompanying the deflected jet are presented and compared with similar data for a round jet issuing from a large flat plate. The spacing and strength of the vortices are calculated using a simple vortex model previously proposed for the flat plate case. The results show that the penetration of the jet and the vortices increases significantly with increasing lift for the range of test parameters covered in the study. The calculated vortex spacing and strength also show an increase with lift.

Mcmahon, H. M.↗

An experimental study of the structure and acoustic field of a jet in a cross stream

The plane of symmetry of a high speed circular jet was surveyed to measure the mean and turbulent velocity fields by using constant temperature hot wire anemometry. The intensity of the noise radiated from the jet was determined in the tunnel test section by utilizing the cross-correlation at a particular time delay between the signals of two microphones suitably located along a given direction. Experimental results indicate that the turbulent intensity inside the crossflow jet increases by a factor of (1 + 1/2) as compared to the turbulent intensity of the same jet under free conditions, with r indicating the ratio of the jet velocity by the cross stream velocity. The peak observed in the turbulence spectra obtained inside the potential core of the jet has a frequency that increases by the same factor with respect to the corresponding frequency measured in the case of the free jet. The noise radiated by the jet becomes more intense as the crossflow velocity increases. The measured acoustic intensity of the crossflow jet is higher than the value which would be expected from the increase of the turbulent intensity only.

Camelier, I.↗

Noise shielding by a hot subsonic jet

An analysis is conducted of the shielding of the noise emitted by a high speed round jet by a hot, subsonic, semicircular jet. A plane wave front in the primary jet is resolved into elementary plane waves which undergo multiple reflections at the jet boundaries of the primary and the shielding jets. The jet boundaries are idealized to be vortex sheets. The far field sound is evaluated asymptotically by a superposition of the waves that penetrate the shielding jet. The angular directivities are plotted for several values of jet temperature and velocity to examine the effectiveness of shielding by the semicircular jet layer.

Vijayaraghavan, A.↗

Analytical study of twin-jet shielding

The development of an analytical model, an aircraft noise prediction computer program, to estimate the shielding of one jet by an adjacent jet in a twin jet configuration, is discussed. Noise estimations included consideration not only of noise sources on the aircraft, but also of the propagation path between source and receiver. A three-dimensional case is considered in which noise source is a discrete frequency point source at rest with respect to the jet axis. The shielding jet is assumed to be a cylinder of heated flow in which the temperature and flow velocity profiles are constant across the jet. The effect on shielding of the orientation of the emitting jet with respect to the shielding jet was investigated. Forward and backward scattering phenomena as well as the influence of jet flow speed were also investigated.

Gerhold, C. H.↗

Aerodynamic levitation of laser-heated solids in gas jets

The aerodynamic levitation technique is developed for studies of high-temperature material properties and gas/condensed-phase reaction kinetics. Stable levitation is demonstrated in a supersonic jet from a 0.081 cm nozzle with 0.03-0.20 g 0.24-0.47 cm diameter solid spheres at a height between 0.7-2.0 cm above the nozzle and ambient pressures between 1.1-18 Torr. A model of supersonic jet levitation is developed which accurately predicts the values of height vs pressure over the full range of conditions investigated. It is found that the efficiency with which jet momentum is converted into levitation force decreases with the jet/specimen diameter ratio and the jet Reynolds number, and the rate of jet spreading with distance from the nozzle is found to agree with that measured by pitot tube traverses of the jet. In addition, laser heating is shown to reduce the jet momentum required for levitation at a given height and to increase levitation stability. Measurements of sphere levitation in subsonic gas jets show that the required jet momentum flow rate exceeds the specimen weight by about 2/the specimen drag coefficient at its terminal free-fall speed under ambient conditions.

Nordine, P. C.↗

Accommodation of practical constraints by a linear programming jet select

An experimental spacecraft control system will be incorporated into the Space Shuttle flight software and exercised during a forthcoming mission to evaluate its performance and handling qualities. The control system incorporates a 'phase space' control law to generate rate change requests and a linear programming jet select to compute jet firings. Posed as a linear programming problem, jet selection must represent the rate change request as a linear combination of jet acceleration vectors where the coefficients are the jet firing times, while minimizing the fuel expended in satisfying that request. This problem is solved in real time using a revised Simplex algorithm. In order to implement the jet selection algorithm in the Shuttle flight control computer, it was modified to accommodate certain practical features of the Shuttle such as limited computer throughput, lengthy firing times, and a large number of control jets. To the authors' knowledge, this is the first such application of linear programming. It was made possible by careful consideration of the jet selection problem in terms of the properties of linear programming and the Simplex algorithm. These modifications to the jet select algorithm may by useful for the design of reaction controlled spacecraft.

Bergmann, E.↗

Vortex modeling of single and multiple dilution jet mixing in a crossflow

An analytical model for the behavior of normally injected jets in a crossflow is developed and applied to fluids of differing densities. Central to the model are the dynamics of the vortex pair structure associated with the local jet cross-section and the entrainment of crossflow by jet fluid. Two specific cases are modeled: one involving a single dilution jet in a crossflow, in which trajectories are found to scale primarily with jet-to-crossflow momentum ratio, and the other involving a series of spanwise jets injected into a crossflow, which indicates scaling with momentum ratio and with the spacing-to-orifice-diameter ratio. In the case of multiple jet penetration, however, merging of the jets into an approximately two-dimensional jet downstream of injection is observed for low spacing-to-diameter ratios.

Karagozian, A. R.↗

Jet characteristics in confined swirling flow

Jets in confined swirling flow are investigated in a facility where the swirling flow in the tube is produced by a vane-type swirler. The jet is located centrally in the swirler, and the diameter ratio of the tube to the jet is about 14. Both the jet and the swirling flow are fully turbulent. Results show that the confined jet is highly dissipative in nature. Consequently, the flow in the tube does not resemble a free jet with axial pressure gradient. The presence of swirl increases the rate of dissipation and the jet decays even faster. A fairly isotropic turbulence field is observed in the confined swirling flow. However, the introduction of the jet does not significantly affect this behavior, and near isotropy of the turbulence field is again observed at about 30 jet diameters downstream.

So, R. M. C.↗

The entrainment rate for a row of turbulent jets

Entrainment rates for a row of isothermal circular air jets issuing into a quiescent environment are found by integrating velocity distributions measured by a linearized hot-wire anemometer. Jet spacing to jet diameter ratios of 2.5, 5, 10, and 20 are studied at jet Reynold's numbers ranging from 5110 to 12070. Velocity distributions are determined at regular downstream intervals at axial distances equal to 16.4 to 164 jet diameters from the jet source. The entrainment rates for the four spacing configurations vary monotonically with increasing spacing/diameter between the limiting case of the slot jet entrainment rate (where the jet spacing to diameter ratio is zero) and the circular jet entrainment rate (in which the spacing to diameter ratio is infinity).

Gordon, Eliott B.↗

Effect of convective Mach number on mixing of coaxial circular and rectangular jets

Rectangular supersonic free and coaxial jets were used to enhance mixing relative to a circular jet in a convective Mach number range of 0.5 to 2.2. The different convective Mach numbers were obtained by changing the central jet gas composition, the temperatures of the inner and outer flows, and the velocity of the coaxial flow. The experimental techniques used were schlieren photography, total pressure, and gas-sampling measurements. For all test conditions the rectangular jets showed substantial improved mixing relative to a circular jet. The free jets showed high mixing in the circumferential region of the jet while the coaxial jet had a high mixing rate inside the central jet.

Gutmark, E.↗

Jetting and the origin of tektites

The scientific consensus is that tektites were produced by impacts on the Earth, but the exact mechanism by impacts might form tektites is still unclear. The most widely cited mechanism is jetting, which results from the extremely high pressures generated at the intersection of two bodies whose surfaces converge obliquely at high speed. Theory of jetting for thin plates is extended to the case of the impact of the sphere onto a half-space. The calculations are done for the impact of a silicate sphere onto a silicate target for impact speeds of 15, 20, and 25 km/sec, spanning the range of reasonable impact speeds for asteroids. The angle of impact is varied from 0 to 75 deg. The mass jetted, the jet velocity, projectile fraction in the jet, azimuthal distribution of the jet, and the phase of the jetted material are calculated as functions of time. The total mass jetted and the overall mass-averages of jet velocity, etc. are also calculated.

Vickery, A. M.↗

Characteristics of two adjacent rectangular jets

Rectangular supersonic (Design Mach number 1.8), single and twin free jets were tested in a Mach number range of 1.2 to 2.4. The objective was to study the interaction between the jets and the effect of the interaction on the spreading rate of the jets. Nozzle spacing in the range of one to four equivalent exit diameters, and jet Mach number were the parameters investigated. The experimental techniques used were Schlieren visualization and direct mixing (gas sampling) measurements from which jet spreading can be readily obtained. At the design Mach number of the nozzles and above the twin jets interact but the interaction does not affect the spreading rate of the jets. At lower Mach numbers, a moderate increase in the twin jets' spread compared to the single jet's spread was observed. The greater increase was observed for nozzle spacing of two equivalent exit diameters. Similar conclusions are drawn from both visualization and direct mixing results.

Zeierman, S.↗

Jet-induced ground effects on a parametric flat-plate model in hover

The jet-induced forces generated on short takeoff and vertical landing (STOVL) aircraft when in close proximity to the ground can have a significant effect on aircraft performance. Therefore, accurate predictions of these aerodynamic characteristics are highly desirable. Empirical procedures for estimating jet-induced forces during the vertical/short takeoff and landing (V/STOL) portions of the flight envelope are currently limited in accuracy. The jet-induced force data presented significantly add to the current STOVL configurations data base. Further development of empirical prediction methods for jet-induced forces, to provide more configuration diversity and improved overall accuracy, depends on the viability of this STOVL data base. The data base may also be used to validate computational fluid dynamics (CFD) analysis codes. The hover data obtained at the NASA Ames Jet Calibration and Hover Test (JCAHT) facility for a parametric flat-plate model is presented. The model tested was designed to allow variations in the planform aspect ratio, number of jets, nozzle shape, and jet location. There were 31 different planform/nozzle configurations tested. Each configuration had numerous pressure taps installed to measure the pressures on the undersurface of the model. All pressure data along with the balance jet-induced lift and pitching-moment increments are tabulated. For selected runs, pressure data are presented in the form of contour plots that show lines of constant pressure coefficient on the model undersurface. Nozzle-thrust calibrations and jet flow-pressure survey information are also provided.

Wardwell, Douglas A.↗

Radio jets in colliding galaxies: Testing the interaction-activity connection

The idea that galaxy interactions and merging are related to the generation of starburst and AGN activity in galactic nuclei has been the subject of intensive investigations over the past several years and is still a matter of lively debate. Peculiar morphologies, indicative of tidal interactions, have been detected in high-luminosity radio galaxies, in quasars, and in ultraluminous IRAS galaxies. In addition, low-luminosity radio and active galaxies show similar evidence for a recent merger or for nearby companions. In a recent CCD optical study of galaxies selected on the basis that they all contain well defined radio jets, it was found that almost half of the sample consists of pairs of elliptical galaxies. Many of these low-luminosity radio galaxies with companions show a well defined distorted radio jet structure at the VLA scale with an S- or C-shaped morphology. We have developed a general numerical simulation algorithm for ballistic radio jets with the intention of applying this model to the study of the bent jets seen in colliding pairs of galaxies and with the hope of testing the well documented interaction-activity connection. In our model the morphological evolution of the jets is determined by their response to the simple mechanical forces (i.e., gravity and ram pressure) imposed on them from both the host and the companion galaxies. Radiative losses, jet precession, magnetic effects, relativistic terms, and hydrodynamic instabilities have all been ignored. Starting with a previously derived collision model for the interacting pair of elliptical galaxies NGC 4782/4783, we have used our algorithm to simulate the specific two-sided jet morphology seen in the radio source 3C 278, associated with NGC 4782. This is the first time that such jet simulations have been produced for a galaxy pair whose relative orbit was determined independently from the jet modeling.

Borne, Kirk D.↗

Performance characteristics of a variable-area vane nozzle for vectoring an ASTOVL exhaust jet up to 45 deg

Many conceptual designs for advanced short-takeoff, vertical landing (ASTOVL) aircraft need exhaust nozzles that can vector the jet to provide forces and moments for controlling the aircraft's movement or attitude in flight near the ground. A type of nozzle that can both vector the jet and vary the jet flow area is called a vane nozzle. Basically, the nozzle consists of parallel, spaced-apart flow passages formed by pairs of vanes (vanesets) that can be rotated on axes perpendicular to the flow. Two important features of this type of nozzle are the abilities to vector the jet rearward up to 45 degrees and to produce less harsh pressure and velocity footprints during vertical landing than does an equivalent single jet. A one-third-scale model of a generic vane nozzle was tested with unheated air at the NASA Lewis Research Center's Powered Lift Facility. The model had three parallel flow passages. Each passage was formed by a vaneset consisting of a long and a short vane. The longer vanes controlled the jet vector angle, and the shorter controlled the flow area. Nozzle performance for three nominal flow areas (basic and plus or minus 21 percent of basic area), each at nominal jet vector angles from -20 deg (forward of vertical) to +45 deg (rearward of vertical) are presented. The tests were made with the nozzle mounted on a model tailpipe with a blind flange on the end to simulate a closed cruise nozzle, at tailpipe-to-ambient pressure ratios from 1.8 to 4.0. Also included are jet wake data, single-vaneset vector performance for long/short and equal-length vane designs, and pumping capability. The pumping capability arises from the subambient pressure developed in the cavities between the vanesets, which could be used to aspirate flow from a source such as the engine compartment. Some of the performance characteristics are compared with characteristics of a single-jet nozzle previously reported.

Mcardle, Jack G.↗

Acoustic properties of supersonic helium/air jets at low Reynolds numbers

Experiments have been performed with the objective of developing a greater understanding of the physics of hot supersonic jet noise. Cold helium/air jets are used to easily and inexpensively simulate the low densities of hot air jets. The experiments are conducted at low Reynolds numbers in order to facilitate study of the large-scale turbulent structures (instability waves) that cause most of the radiated noise. Experiments have been performed on Mach 1.5 and 2.1 jets of pure air, pure helium and 10 percent helium by mass. Helium/air jets are shown to radiate more noise than pure air jets due to the increased exit velocity. Microphone spectra are usually dominated by a single spectral component at a predictable frequency. Increasing the jet's helium concentration is shown to increase the dominant frequency. The helium concentration in the test chamber is determined by calculating the speed of sound from the measured phase difference between two microphone signals. Bleeding outside air into the test chamber controls the accumulation of helium so that the hot jet simulation remains valid. The measured variation in the peak radiated noise frequency is in good agreement with the predictions of the hot jet noise theory of Tam et al.

Mclaughlin, Dennis K.↗