Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “emittance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Condition of chromic acid anodized aluminum clamps flown

A survey of the condition of the chromic acid anodized (CAA) coating on selected LDEF tray clamps was carried out. Measurements of solar absorptance and thermal emittance were carried out at multiple locations on both the space exposed and spacecraft facing sides of the clamps. Multiple clamps from each available angle relative to the ram direction were examined. The diffuse component of the reflectance spectrum was measured for a selected subset of the clamps. The thickness of the CAA was determined for a small set of clamps. Examples of variation in integrity of the coatings from leading to trailing edge will be shown.

Plagemann, W. L.↗
NASA NTRS1991

A comparative study of p(+)n and n(+)p InP solar cells made by a closed ampoule diffusion

The purpose was to demonstrate the possibility of fabricating thermally diffused p(+)n InP solar cells having high open-circuit voltage without sacrificing the short circuit current. The p(+)n junctions were formed by closed-ampoule diffusion of Cd through a 3 to 5 nm thick anodic or chemical phosphorus-rich oxide cap layer grown on n-InP:S Czochralski LEC grown substrates. For solar cells made by thermal diffusion the p(+)n configuration is expected to have a higher efficiency than the n(+)p configuration. It is predicted that the AM0, BOL efficiencies approaching 19 percent should be readily achieved providing that good ohmic front contacts could be realized on the p(+) emitters of thickness lower than 1 micron.

Faur, M.↗
NASA NTRS1991

Improvements in contact resistivity and thermal stability of Au-contacted InP solar cells

Specific contact resistivities for as-fabricated Au contacts on n-p InP solar cells are typically in the 10(exp -3) ohm/sq cm range, but contact resistivities in the 10(exp -6) ohm/sq cm range can be obtained if the cells are heat treated at 400 C for a few minutes. This heat treatment, however, results in a dramatic drop in the open circuit voltage of the cell due to excessive dissolution of the emitter into the metallization. It was found that low values of contact resistivity can be secured without the accompanying drop in the open circuit voltage by adding Ga and In in the Au metallization. It is shown that Au contacts containing as little as 1 percent atomic Ga can suppress the reaction that takes place at the metal-InP interface during heat treatment, while exhibiting contact resistivity values in the low 10(exp -5) ohm/sq cm. Detailed explanations for the observed superior thermal stability of these contacts are presented.

Fatemi, Navid S.↗
NASA NTRS1991

Development of N/P AlGaAs free-standing top solar cells for tandem applications

The combination of a free standing AlGaAs top solar cell and an existing bottom solar cell is the highest performance, lowest risk approach to implementing the tandem cell concept. The solar cell consists of an AlGaAs substrate layer, an AlGaAs base layer, an AlGaAs emitter, and an ultra-thin AlGaAs window layer. The window layer is compositionally graded which minimizes reflection at the window layer/emitter interface and creates a built-in electric field to improve quantum response in the blue region of the spectrum. Liquid phase epitaxy (LPE) is the only viable method to produce this free standing top solar cell. Small (0.125 sq cm), transparent p/n AlGaAs top solar cells were demonstrated with optimum bandgap for combination with a silicon bottom solar cell. The efficiency of an AlGaAs/Si stack using the free standing AlGaAs device upon an existing silicon bottom solar cell is 24 pct. (1X, Air Mass Zero (AM0). The n/p AlGaAs top solar cell is being developed in order to facilitate the wiring configuration. The two terminal tandem stack will retain fit, form, and function of existing silicon solar cells. Progress in the development of large area (8 and 16 sq cm), free standing AlGaAs top solar cells is discussed.

Negley, Gerald H.↗
NASA NTRS1991

InP concentrator solar cells for space applications

The design, fabrication, and characterization of high-performance, n(+)/p InP shallow-homojunction (SHJ) concentrator solar cells is described. The InP device structures were grown by atmospheric-pressure metalorganic vapor phase epitaxy (APMOVPE). A preliminary assessment of the effects of grid collection distance and emitter sheet resistance on cell performance is presented. At concentration ratios of over 100, cells with AM0 efficiencies in excess of 21 percent at 25 C and 19 percent at 80 C are reported. These results indicate that high-efficiency InP concentrator cells can be fabricated using existing technologies. The performance of these cells as a function of temperature is discussed, and areas for future improvement are outlined.

Ward, J. S.↗
NASA NTRS1990

Impact ionization in the base of a hot-electron AlSb/InAs bipolar transistor

The operation of a new AlSb/InAs heterojunction bipolar transistor is studied. The electrons are injected into a p-InAs base across the AlSb/InAs heterojunction. The conduction-band discontinuity at this heterojunction is sufficiently large so that energy of the electrons injected into InAs exceeds the threshold for generating electron-hole pairs by impact ionization. The observed incremental common base current at zero collector-base bias decreases and becomes negative as the emitter current is increased, thus providing direct evidence for impact ionization entirely by band-edge discontinuities.

Vengurlekar, Arvind S.↗
NASA NTRS1989

Using passive, thermal remote sensing techniques for detecting subsurface gravel accumulations in vegetated, unconsolidated sedimentary terrains

Multiband radiometric data from an airborne imaging thermal scanner are being studied for use in finding buried gravel deposits. The techniques are based on measuring relative differences in the thermal properties between gravel-laden targets and the surrounding gravelless background. These properties are determined from modeling the spectral radiant emittance recorded over both types of surfaces in conjunction with ground measurements of the most significant heat flows above and below the surface. Thermodynamic properties of sampled materials from control sites are determined, and diurnal and annual subsurface heat waves are recorded. Thermal models that account for heat exchange at the surface, as well as varying levels of soil moisture, humidity, and vegetation, are needed for adaptation and modification to simulate the physical and radiative environments of this region.

Burns, Gregory S.↗
NASA NTRS1990

On the nature and implications of starburst-driven galactic superwinds

Optical spectroscopic data are presented on the ionized nebulae associated with 14 galaxies that are strong far-IR emitters. It is found that the data provide both qualitative and quantitative support for the 'superwind' model in which the kinetic energy provided by SNe and winds from massive stars in a central starburst drives a large-scale outflow that can shock heat and accelerate ambient interstellar and circumgalactic gas. Clear kinematic signatures of an outflow along the galaxy's minor axis are found for the three nearest far-IR galaxies (FIRGs). The FIRG nebulae are highly overpressured relative to the Galactic ISM, with the pressure dropping systematically with distance from the nucleus. Superwinds are energetically adequate to power both the observed optical and X-ray nebulae, and the relative emission-line intensities and their radial variations are consistent with ionization by wind-driven shocks, but not with photoionization by normal O stars or an AGN. The possible astrophysical implications of superwinds are discussed.

Heckman, Timothy M.↗
NASA NTRS1990

The 27-28 October 1986 FIRE IFO cirrus case study - Comparison of radiative transfer theory with observations by satellite and aircraft

Observations of cirrus and altocumulus clouds during the FIRE are compared to theoretical models of cloud radiative properties. Three tests are performed. First, radiances are used to compare the relationship between nadir reflectance ot 0.83 micron and beam emittance at 11.5 microns with that predicted for model calculations using spherical and nonspherical phase functions. Good agreement is found between observations and theory when water droplets dominate. Poor agreement is found when ice particles dominate, especially using spherical-particle phase functions (SPPFs). Even when compared to a laboratory-measured ice-particle phase function (IPPF), the observations show great side-scattered radiation than the theoretical calculations. Second, the anisotropy of conservatively scattered radiation is examined using simultaneous multiple angle views of the cirrus from Landsat and ER-2 aircraft radiometers. Observed anisotropy gives good agreement with theoretical calculations using the laboratory IPPF and poor agreement with an SPPF. Third, Landsat radiances at 0.83, 1.65, and 2.21 microns are used to infer particle phase and size. For water droplets, good agreement is found with particle-probe measurements in the cloud. For ice particles, the Landsat radiance observations predict an effective radius of 60 microns versus aircraft observations of about 200 microns. It is suggested that this discrepancy may be explained by uncertainty in the imaginary index of ice and by inadequate measurements of small ice particles by microphysical probes.

Wielicki, Bruce A.↗
NASA NTRS1990

The 27-28 October 1986 FIRE IFO cirrus case study - In situ observations of radiation and dynamic properties of a cirrus cloud layer

Observations are presented of cirrus cloud radiative, microphysical, and dynamic properties, their variability, and apparent scale sizes, as observed from NCAR Sabreliner on October 28, 1986. Broadband mass-absorption coefficients were deduced as a function of depth into the cirrus cloud and found to vary with particle dimension. Broadband volume absorption coefficients were deduced. By employing a diffusivity factor of 1.49 this agreement was maximized. Calculated infrared heating rates were typical of thin cirrus layers. The cloud top cooling and cloud base warming were observed to become more accentuated for the denser portions of cloud. The broadband emittances due to the cloud aerosol were found to approach 0.5 to 0.6. The cirrus clouds were observed to exhibit significant horizontal variability and a significant amount of scatter was evident when attempting to relate the broadband infrared and shortwave radiative properties. It is suggested that these radiative properties, which are modulated by the cloud elements, have their scales determined by the eddies detected in the analysis of wind components.

Smith, William L., Jr.↗
NASA NTRS1991

Thermographic monitoring of materials under simulated reentry conditions

Thermography can be used to measure surface temperature gradients graphically, and can be used under conditions where the direct measurement of temperature at all desired points, using thermocouples or resistance temperature detectors (RTDs), is either difficult or impossible. The use of thermographic monitoring during a series of arc-jet tests is described. Described in this work are the issues that influence interpretation of the thermographic measurements under these conditions, including the calculation of effective emittance and window transmittance from the spectral properties of the materials in order to calculate the temperature distribution of a surface directly from the measured radiance. Comparison of the surface temperatures measured using thermocouples and the temperatures derived from thermographic measurements show good agreement. The data gathered will be used to evaluate important test parameters such as the heating distribution across the surface of a heat shield test model and at steps on the model surface.

White, Susan M.↗
NASA NTRS1990

Surface studies on scandate cathodes and synthesized scandates

Auger, ESCA, electron emission, evaporation, and desorption measurements were made on three different types of scandate surfaces. They are: (1) an impregnated top layer scandate cathode, (2) an unimpregnated top layer scandate cathode with a deposited barium or barium oxide adsorbate surface layer, and (3) a synthesized scandate surface, which replicates a scandate cathode surface. The purpose of these experiments was to determine the role that Sc2O3 plays in making the scandate cathode a more copious electron emitter than the conventional impregnated-type cathode. The synthesized scandate surface experiments consisted of depositing multilayer scandium on a tungsten surface, oxidizing the scandium, and then depositing either Ba or BaO on the scandium oxide surface. The results of these measurements showed that the low work function portions of the thin-film scandate cathode are where the Sc2O3 is the substrate and BaO is the adsorbate.

Lesny, Gary↗
NASA NTRS1990

Surface recombination velocity and lifetime in InP measured by transient microwave reflectance

Minority carrier lifetime and surface recombination velocity are determined in organometallic vapor-phase epitaxy (OMVPE)-grown InP by a contactless microwave technique. For lightly doped n-type InP, a surface recombination velocity of 5000 cm/s is measured. However, in solar cells with a heavily doped n-type emitter a surface recombination velocity of 1 x 10 to the 6th cm/s is observed. Possible reasons for this due to surface pinning are discussed. The effects of various chemical treatments and SiO on the surface recombination velocity are measured.

Bothra, S.↗
NASA NTRS1991

Observations that link infrared cirrus and ultraviolet extinction

Results are presented of UV extinction measurements of 17 stars in the open cluster IC 4665 and of four stars in the open cluster NGC 1647, showing that the UV extinctions of the two clusters stars have different properties. Whereas the stars in NGC 1647 cluster are typical of general interstellar space, the stars in IC 4665 have a small 'linear' term which is typical of stars found near regions of active star formation. Using data from the IRAS satellite to study the emission by the 'infrared cirrus' for each of the regions and to measure the I(60-micron)/I(100-micron) ratio for the two regions, it was found that, when the linear term component is present, it dominates the 100-micron cirrus emission. When it is absent, the 100-micron emission is from the relatively hot particles that are responsible for the 60-micron emission. It is suggested that the 60-micron emitters are small carbonaceous grains that are major contributors to all parts of the UV extinction except the linear term.

Hackwell, John A.↗
NASA NTRS1991

Search for TeV emission from 4U 0115 + 63

While previous studies of the X-ray binary 4U 0115+63 suggest it to be a steady, TeV gamma-ray emitter, with pulses at the 3.6-sec neutron-star period, the present analysis of data obtained on 60 nights over a 4-yr period with an imaging gamma-ray telescope has uncovered no indication of TeV signals. The derived upper limit of 1 x 10 to the -11th/sq-cm sec, for gamma-rays of energy above 0.7 TeV, is noted to be significantly below the previously reported fluxes.

Macomb, D. J.↗
NASA NTRS1990

The EXOSS mission for hard X-ray astronomy

The basis for the Energetic X-ray Observatory on Space Station is described. Attention is given to the principal scientific objectives of EXOSS, namely, to study in detail AGN and quasars (some 10,000 should be detectable) as well as compact Galactic sources (accreting white dwarfs, neutron stars, and black holes), and to probe both nonthermal and high-temperature thermal phenomena and the fundamental nature of these objects. The principal technical characteristics of the EXOSS baseline instrument, which overlap in sensitivity in the approximately 40-to-60-keV band, are presented. EXOSS should facilitate efforts to determine: the central power source and the dominant emission mechanisms in AGN, the ways in which the various AGN classes differ as hard X-ray and soft gamma-ray emitters, and the contribution of AGN to the diffuse hard X-ray and soft gamma-ray background.

Grindlay, Jonathan E.↗
NASA NTRS1991

Second-epoch VLA observations of compact radio sources in NGC 253

Results are presented of second-epoch 6-cm VLA observations of the starburst galaxy NGC 253 in early 1989, approximately 18 months after the first observations identified more than 30 compact radio sources in the galaxy. The galaxy was also mapped at 3.6 cm. No new radio sources were found at 6 cm after the 18-month interval. Assuming that at least two-thirds of new type II supernovae would have been detectable radio emitters stronger than 3 mJy, the 95-percent confidence upper limit to the SN rate is 3.0/yr. None of the 13 sources with flux densities above 1 mJy showed significant decreases in strength over 18 months; the strongest source showed an apparent increase of 6.5 percent in flux density, which differs from that of Kronberg and Sramek (1985) for M82. The 3.6 map identified a number of new sources because of the reduction of confusion. The available spectral data show that a few of the resolved sources may be H II regions.

Ulvestad, James S.↗
NASA NTRS1992

Video System Highlights Hydrogen Fires

Video system combines images from visible spectrum and from three bands in infrared spectrum to produce color-coded display in which hydrogen fires distinguished from other sources of heat. Includes linear array of 64 discrete lead selenide mid-infrared detectors operating at room temperature. Images overlaid on black and white image of same scene from standard commercial video camera. In final image, hydrogen fires appear red; carbon-based fires, blue; and other hot objects, mainly green and combinations of green and red. Where no thermal source present, image remains in black and white. System enables high degree of discrimination between hydrogen flames and other thermal emitters.

Youngquist, Robert C.↗