Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “component model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

An architecture for object-oriented intelligent control of power systems in space

A control system for autonomous distribution and control of electrical power during space missions is being developed. This system should free the astronauts from localizing faults and reconfiguring loads if problems with the power distribution and generation components occur. The control system uses an object-oriented simulation model of the power system and first principle knowledge to detect, identify, and isolate faults. Each power system component is represented as a separate object with knowledge of its normal behavior. The reasoning process takes place at three different levels of abstraction: the Physical Component Model (PCM) level, the Electrical Equivalent Model (EEM) level, and the Functional System Model (FSM) level, with the PCM the lowest level of abstraction and the FSM the highest. At the EEM level the power system components are reasoned about as their electrical equivalents, e.g, a resistive load is thought of as a resistor. However, at the PCM level detailed knowledge about the component's specific characteristics is taken into account. The FSM level models the system at the subsystem level, a level appropriate for reconfiguration and scheduling. The control system operates in two modes, a reactive and a proactive mode, simultaneously. In the reactive mode the control system receives measurement data from the power system and compares these values with values determined through simulation to detect the existence of a fault. The nature of the fault is then identified through a model-based reasoning process using mainly the EEM. Compound component models are constructed at the EEM level and used in the fault identification process. In the proactive mode the reasoning takes place at the PCM level. Individual components determine their future health status using a physical model and measured historical data. In case changes in the health status seem imminent the component warns the control system about its impending failure. The fault isolation process uses the FSM level for its reasoning base.

Holmquist, Sven G.↗
NASA NTRS2012

Modeling Radar Scatter from Icy and Young Rough Lunar Craters

For lunar orbital synthetic aperture radars, such as the Chandrayaan Mini-RF operating at S- band (13-cm) wavelength and the Lunar Reconnaissance Orbiter Mini-RF operating at S- band and X-band (3-cm) wavelengths, it is important to understand the radar backscattering characteristics of the icy and young, rough craters. Assuming a mixing model consisting of diffuse and quasi-specular scattering components, we have modeled the opposite-sense circular (OC) and same-sense circular (SC) backscattering characteristics. The specular component, consisting of only OC echoes, represents the echoes from the surface and subsurface layers that are oriented perpendicular to the radar's line-of-sight. The diffuse component, consisting of both SC and OC echoes, represents the echoes associated with either rocks or ice. Also, diffuse echoes have backscatter that is proportional to the cosine of the incidence angle. We modeled how these two (specular and diffuse) radar scattering components could be modulated by factors such as surface roughness associated with young craters. We also modeled how ice radar scattering components could be modulated by a thin regolith covering, and/or by the situation where ice occupies small patches within a larger radar pixel. We tested this modeling by examining 4 nonpolar craters and 12 polar craters using LRO Mini-RF data. Results indicate that icy and young rough craters can be distinguished based upon their SC enhancements (Alpha) and OC enhancements (Gamma). In addition, we also examined the craters that have unusual circular polarization ratios (CPRs) that likely result from a double bounce mode of scattering. Blocky fresh craters, icy craters, and craters exhibiting double bounce scattering can be separated based on the values of Alpha, Gamma, the ratio of Alpha/Gamma and the weighted sum of Alpha and Gamma.

lunar craters↗
DOE OSTI2022

Bond Length Alternation and Internal Dynamics in Model Aromatic Substituents of Lignin

In this report broadband microwave spectra were recorded over the 2-18 GHz frequency range for a series of four model aromatic components of lignin; namely, guaiacol (ortho-methoxy phenol, G), syringol (2,6-dimethoxy phenol, S), 4-methyl guaiacol (MG), and 4-vinyl guaiacol (VG), under jet-cooled conditions in the gas phase. Using a combination of 13 C isotopic data and electronic structure calculations, distortions of the phenyl ring by the substituents on the ring are identified. In all four molecules, the r C(1)-C(6) bond between the two substituted C-atoms lengthens, leading to clear bond alternation that reflects an increase in the phenyl ring resonance structure with double bonds at r C(1)-C(2) , r C(3)-C(4) and r C(5)-C(6) . Syringol, with its symmetric methoxy substituents, possesses a microwave spectrum with tunneling doublets in the a-type transitions associated with H-atom tunneling. These splittings were fit to determine a barrier to hindered rotation of the OH group of 1975 cm -1 , a value nearly 50% greater than that in phenol, due to the presence of the intramolecular OH…OCH 3 H-bonds at the two equivalent planar geometries. In 4-methyl guaiacol, methyl rotor splittings are observed and used to confirm and refine an earlier measurement of the three-fold barrier V 3 = 67 cm -1 . Finally, 4-vinyl guaiacol shows transitions due to two conformers differing in the relative orientations of the vinyl and OH groups.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Assessing geothermal/solar hybridization – Integrating a solar thermal topping cycle into a geothermal bottoming cycle with energy storage

Geothermal and concentrating solar power (CSP) technologies typically use heat at different temperatures in their commercial deployments. This enables a technically viable hybridization of a solar topping cycle and a geothermal bottoming cycle at locations where both resources are available. In this article, an underperforming geothermal power system based at Burley, Idaho is used as a baseline to investigate the technical and economic potential of such a hybrid cycle. A direct thermal energy storage (TES) system is also integrated to overcome the intermittency of the solar resource. Design and off-design behavior of key components are modelled to simulate the annual performance of the hybrid system on an hourly basis. The sizing of the solar field and thermal storage is investigated and is seen to significantly impact the annual electricity generation and efficiency. Various cost scenarios for the solar field and thermal energy storage are investigated. An economic metric - levelized cost of electricity (LCOE) - is used to optimize the solar field sizing and TES capacity. The hybrid plant converts the additional solar heat input into additional work with an efficiency of 32.9%. Retrofitting a geothermal plant with solar and eight hours of energy storage can achieve an LCOE of 0.136 $/kWhe in current cost scenarios and 0.081 $/kWhe in a future cost reduction scenario. Although the hybrid system cannot directly compete with current PV systems without batteries, it has an LCOE 32% lower than that of a PV-battery system. This paper provides insights into the research and development of the future grid with a high renewable energy penetration and encourages further study of energy hybridization for improved efficiencies and economics.

15 GEOTHERMAL ENERGY↗
DOE OSTI2025

Automated vehicle microscopic energy consumption study (AV-Micro): Data collection and model development

While the Adaptive Cruise Control (ACC) system in automated vehicles (AVs) is expected to impact transportation energy significantly, existing AV energy consumption models only directly adopt those developed with Human-driven Vehicle (HV) data without even slight adaptation or calibration to accommodate unique AV energy consumption features. This study will investigate how accurately HV data-based models can predict the energy consumption of AVs. Empirical trajectory data and corresponding instantaneous energy consumption rates from both AVs and HVs were collected. We adopted two classical HV data-based models to fit these data. The calibration results indicated that these models yield around 20 30% prediction errors for AVs. To further improve the prediction accuracy, this study designed an AV-Micro model by incorporating components of multiple classic energy consumption models that better capture ACC energy consumption features, including piecewise driving behavior. With this, the AV-Micro model achieves lower than 10% prediction errors. The AV-Micro model’s high consistency across different test runs was verified with statistical significance tests, demonstrating its adaptability in different driving profiles. To confirm the discrepancies between the energy consumption features of AVs and HVs, more statistical significance tests were conducted to show that the AV-Micro model cannot be directly applied to HV data. The findings by calibrated AV-Micro models revealed that AVs consume approximately 80.5–146.4 J more energy than HVs for each meter traveled. Furthermore, the frequency analysis of energy consumption indicates that there is still some room for AVs to improve energy efficiency, particularly given their larger amplitude high-frequency fluctuations.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Investigating the application of Kalman Filters for real-time accountancy in fusion fuel cycles

Here tritium accountancy in the fusion fuel cycle is a significant concern for the operation of commercial devices. It is expected that a limit on the maximum amount of tritium inventory in the system will be implemented, meaning that accountancy of the tritium inventory in the fuel cycle will need to be as accurate as possible. This is difficult since not all locations along the fuel cycle can benefit from the implementation of a tritium accountancy sensor and measurements will inherently contain error. Commercial fusion plants will also operate continuously, challenging current accountancy techniques that rely on static processes in well-controlled environments. In this paper a simple fusion fuel cycle concept is defined and the tritium inventory over time of each component is modelled using the Euler Approximation of a series of differential Equations in Python. This information is then used to simulate sensor measurements at specific points on the fuel cycle and then passed through a Kalman Filter (KF) to improve the accuracy of the true measurement of the sensors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Evaluation of flow-induced plate deflection for University of Missouri research reactor low-enriched uranium fuel element

The University of Missouri Research Reactor (MURR), located on the campus of the University of Missouri in Columbia, Missouri, is one of the six United States (U.S.) High Performance Research Reactors (USHPRR), including one critical facility, that are actively collaborating with the U.S. Department of Energy (DOE) National Nuclear Security Administration (NNSA) Office of Material Management and Minimization (M3) Reactor Conversion Program to convert from highly enriched uranium (HEU, ≥20 wt% U-235) fuel to low-enriched uranium (LEU, <20 wt% U-235) fuel. A new type of very high-density LEU fuel based on a monolithic alloy of uranium and 10 wt% molybdenum (U-10Mo) is expected to allow conversion of some USHPRR, including MURR. In the design of its fuel elements, MURR is using thin parallel curved fuel plates separated by coolant channels. In this work, fluid-structure interaction (FSI) analysis of the MURR LEU fuel element is performed at the element level (as compared to the plate level analysis), which models all components of the LEU fuel element, including fuel plates and the supporting structures. Therefore, the effect of supporting structures on the flow distribution within the element and the fuel plate deflection are evaluated. In addition to the element nominal flow rate and dimensions, the tolerances in the geometry of the coolant channel and plate thickness, the effect of a comb on plate deflection, and the uncertainty of the flow rate per element are evaluated. For the LEU fuel plates, which are thinner than the current HEU plates, the predicted plate deflection is found to be small compared to the fabrication and assembly tolerances. Thus, the FSI-induced deflections are not expected to noticeably reduce the coolant flow rate or predicted safety margins in the limiting channels for the MURR LEU fuel element. In addition to the simulation work, a hydraulic performance test of the MURR LEU fuel element is currently being planned to support conversion to the use of LEU fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Renewable energy analysis in indigenous communities using bottom-up demand prediction

This paper provides a methodology for the holistic analysis of hybrid renewable energy systems in rural communities. Electric demand is an important component for modeling and analysis of renewable energy systems. Typically, electric demand data is not available due to the internal privacy policies of utility providers. Therefore, this study proposes the use of bottom-up approaches for the development of the electric demand profile, considering the general homogeneity of residential and commercial buildings in rural communities. As a test case, this study develops the electric demand profile and investigates the technical and environmental feasibility of a hybrid renewable energy system for the New Town community on the Fort Berthold Indian Reservation (FBIR) in North Dakota. This study conducts the hybrid renewable energy system’s analysis by developing scripts in the LK scripting language and integrating System Advisor Model software’s open-source modules for modeling of renewable energy systems. Here, the results for the validation testbed of this study show that hybrid renewable resources have higher ratios of energy used for self-consumption to the total energy generated compared to stand-alone wind and PV farms.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2023

Electrochemically driven phase transformation for high-efficiency heat pumping

To reduce energy consumption and improve energy utilization in space conditioning, advanced heat pumping technologies are needed. The chemical looping heat pump (CLHP) is a promising thermodynamic cycle that has theoretically shown the potential to achieve a cooling coefficient of performance (COP c ) increase of over 20% relative to conventional vapor compression systems. In this paper, the key process of the CLHP is experimentally demonstrated, and the system performance and non-ideal behavior are predicted using the component-level models. The results show the feasibility of electrochemical phase change of a working fluid; the peak COP c was 7.64 with a cooling capacity of 3.6 mW (cooling density of 2.57 W m -2 ) at both sink and source temperature of 23°C based on laboratory experiments. The COP c can theoretically reach up to 13 at a temperature lift of 15°C as long as an electrochemical cell can achieve a greater degree of conversion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

A Julia Framework for Graph-Structured Nonlinear Optimization

Graph theory provides a convenient framework for modeling and solving structured optimization problems. Under this framework, the modeler can arrange/assemble the components of an optimization model (variables, constraints, objective functions, and data) within nodes and edges of a graph, and this representation can be used to visualize, manipulate, and solve the problem. In this work, we present a Julia framework for modeling and solving graph-structured nonlinear optimization problems. Our framework integrates the modeling package Plasmo.jl (which facilitates the construction and manipulation of graph models) and the nonlinear optimization solver MadNLP.jl (which provides capabilities for exploiting graph structures to accelerate solution). We illustrate with a simple example how model construction and manipulation can be performed in an intuitive manner using Plasmo.jl and how the model structure can be exploited by MadNLP.jl. We also demonstrate the scalability of the framework by targeting a large-scale, stochastic gas network problem that contains over 1.7 million variables.

Cole, David↗
DOE OSTI2021

Safety moments in chemical safety education.

Chemical safety education is a critical aspect of an integrated culture of safety in academic research settings. Showcasing best practices and sharing practical solutions for recognizing hazards and minimizing risks represent one way of reinforcing a research community's actions, attitudes, and behavior toward safety. For goals of improving chemical safety education with nonformal endeavors, safety moments are similar to 1-2 slides that focus on raising awareness and knowledge for routine safety issues in research laboratories. Intended to catalyze brief discussions at the beginning of meetings and presentations, these materials provide a proactive way for students and faculty to engage in open communication on diverse research safety topics across science and engineering. This commentary provides an overview of designing effective safety moments and tailoring them to highlight practical safety needs and considerations. Key components of model safety moment slides are presented, alongside centralized resources assembled by student-led laboratory safety teams, which can also be extended to posters, social media platforms, online videos, and other forms of scientific communication. Combined with both top-down backing from institution leaders and bottom-up support from student researchers, safety moments remain a low-barrier risk reduction strategy that is easy to implement, encourages local dialogue on safety, combats complacency, and holds potential for facilitating long-term improvements to academic lab safety culture.

Communication/Writing↗
DOE OSTI2026

Chemical and Structural Insights into Solid Electrolyte Interphase Evolution for Sodium Metal Electrodes

The solid electrolyte interphase (SEI) critically governs the reversibility of sodium metal batteries, through dynamically mediating ion transport and interfacial reactions. However, its kinetic evolution under operating conditions, and how it influences interfacial stability, remains poorly understood. Here, in this study, we reveal that the SEI undergoes coupled chemical and mechanical changes during sodium plating and stripping, leading to spatial and temporal heterogeneity that drives interfacial degradation. Synchrotron operando grazing-incidence wide-angle X-ray scattering and soft X-ray absorption spectroscopy capture the sequential formation and dissolution of inorganic SEI phases (NaF, NaH, NaOH, Na 2 PO 3 F), accompanied by depth-dependent alterations in organic SEI components. Mesoscale modeling connects this evolving SEI heterogeneity to localized current density fluctuations and stress accumulation at the Na interface, identifying pathways to electrically isolated sodium formation. These findings show that SEI instability fundamentally limits reversibility in sodium metal batteries, and that controlling SEI chemistry–mechanics coupling is essential to achieving its durability.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Enhancing Hydrogen Production from Bioenergy Crops via Photoreforming

Photoreforming perennial bioenergy crops (willow, Miscanthus , and poplar) has the potential to produce H 2 with reduced environmental impacts. To understand the compositional effects of the biomass on the average rate of H 2 production over the first 30 min of reaction ( r H 2 ), the r H 2 values of model biomass component (i.e., cellulose, hemicellulose, and lignin) mixtures were compared with those from the raw biomass. The higher cellulose or hemicellulose content in multicomponent mixtures resulted in higher r H 2 , whereas lignin reduced the hydrogen production rate. However, with raw biomass, the ratio of biomass components alone did not determine the r H 2 via photoreforming, with rates of hydrogen production for different varieties of willow ranging between 1.9 μmol h -1 and 12.3 μmol h -1 , 11.8 μmol h -1 for a poplar, and 6.8 μmol h -1 for a miscanthus biomass. In addition, comparable r H 2 values of raw poplar and its extracted cellulose via an IonoSolv treatment indicated the possibility of using raw biomass materials without delignification for generating H 2 via photoreforming. Importantly, r H 2 was positively correlated with the interaction between water and the biomass, as assessed by NMR relaxation via an examination of the T 1 /T 2 ratio. A stronger water-biomass interaction resulted in a higher r H 2 . Genetic modification of biomass has been suggested as a putative way to improve the r H 2 of biomass with an enhanced interaction with water. This research enhances the understanding of factors influencing H 2 production from lignocellulosic biomass by photoreforming and supports the breeding and management of perennial biomass crops to maximize H 2 yields while minimizing land area requirements.

biomass↗
DOE OSTI2023

Acclimation of Phytoplankton Fe:C Ratios Dampens the Biogeochemical Response to Varying Atmospheric Deposition of Soluble Iron

Abstract Dissolved iron (dFe) plays an important role in regulating marine productivity. In high nutrient, low chlorophyll regions (>33% of the global ocean), iron is the primary growth limiting nutrient, and elsewhere iron can regulate nitrogen fixation by diazotrophs. The link between iron availability and carbon export is strongly dependent on the phytoplankton iron quotas or cellular Fe:C ratios. This ratio varies by more than an order of magnitude in the open ocean and is positively correlated with ambient dFe concentrations in field observations. Representing Fe:C ratios within models is necessary to investigate how ocean carbon cycling will interact with perturbations to iron cycling in a changing climate. The Community Earth System Model ocean component was modified to simulate dynamic, group‐specific, phytoplankton Fe:C that varies as a function of ambient iron concentration. The simulated Fe:C ratios improve the representation of the spatial trends in the observed Fe:C ratios. The acclimation of phytoplankton Fe:C ratios dampens the biogeochemical response to varying atmospheric deposition of soluble iron, compared to a fixed Fe:C ratio. However, varying atmospheric soluble iron supply has first order impacts on global carbon and nitrogen fluxes and on nutrient limitation spatial patterns. Our results suggest that pyrogenic Fe is a significant dFe source that rivals mineral dust inputs in some regions. Changes in dust flux and iron combustion sources (anthropogenic and wildfires) will modify atmospheric Fe inputs in the future. Accounting for dynamic phytoplankton iron quotas is critical for understanding ocean biogeochemistry and projecting its response to variations in atmospheric deposition.

Environmental Sciences & Ecology↗
DOE OSTI2020

Autonomous adaptive data acquisition for scanning hyperspectral imaging

Non-invasive and label-free spectral microscopy (spectromicroscopy) techniques can provide quantitative biochemical information complementary to genomic sequencing, transcriptomic profiling, and proteomic analyses. However, spectromicroscopy techniques generate high-dimensional data; acquisition of a single spectral image can range from tens of minutes to hours, depending on the desired spatial resolution and the image size. This substantially limits the timescales of observable transient biological processes. To address this challenge and move spectromicroscopy towards efficient real-time spatiochemical imaging, we developed a grid-less autonomous adaptive sampling method. Our method substantially decreases image acquisition time while increasing sampling density in regions of steeper physico-chemical gradients. When implemented with scanning Fourier Transform infrared spectromicroscopy experiments, this grid-less adaptive sampling approach outperformed standard uniform grid sampling in a two-component chemical model system and in a complex biological sample, Caenorhabditis elegans. We quantitatively and qualitatively assess the efficiency of data acquisition using performance metrics and multivariate infrared spectral analysis, respectively.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

On the force exerted on a non-spherical asymmetric dust grain from homogeneous, stationary, isotropic, non-magnetized plasma

Whereas the conventional wisdom suggests that the force between non-magnetized homogeneous, stationary, isotropic plasma, and the dust grain is only possible for the case of relative plasma–grain velocity, it is shown that stationary non-spherical asymmetric dust grain immersed in stationary, non-magnetized, isotropic plasma can experience a force caused by the grain–plasma interactions. The component of the force due to scattering of plasma particles in the limit of infinite Debye length is considered analytically. Both the particle scattering and absorption force components are modeled numerically in the limits of infinite and finite Debye length using a newly developed 2D3V Aspherical Particle-in-Cell code. The code simulates interactions of dust grain of selected non-spherical asymmetric shape with plasmas using dust shape conforming coordinates. Here, the simulations confirm the existence of the force on non-spherical asymmetric grain in stationary non-magnetized plasma and show that the plasma screening effects can lead to reversal of the force direction.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Preliminary design overview and performance assessment of the ITER low-field side reflectometer

The design of the ITER low-field side reflectometer (LFSR) has matured to a complete end-to-end preliminary design. LFSR will supply three key plasma measurements: (1) electron density profile, (2) electron density fluctuations, and (3) poloidal rotation. Simultaneous measurements of the three quantities are enabled by an array of six monostatic antennas which inject from an equatorial port on the outboard side of the ITER vessel. Low-loss transmission lines, consisting of corrugated, overmoded waveguide and miter bends, transmit the 30–165 GHz, O- and X-mode signals to and from the ITER plasma. Integrated transmission-line components serve a range of purposes, such as protection from high-power stray radiofrequency radiation, accommodation of transmission-line displacement, and simultaneous measurement of reference and plasma phases during the discharge. Broadband transmission signals are realized by full-band microwave transceivers combined with quasi-optical multiplexing. A field-programmable gate array (FPGA) processor demodulates the profile reflectometer signals, enabling real-time density profile measurements for plasma control system feedback. A full-scale transmission line test facility provides an integrated environment to assess the performance of critical LFSR components. Theoretical modeling together with insertion loss measurements provide the basis for a comprehensive power budget, which accounts for transmitted output power, transmission-line losses, antenna coupling, and plasma effects. Results indicate that high signal-to-noise ratios are achievable with the current design. A synthetic reflectometer model, using real design parameters and baseline ITER profiles, has been developed to estimate the return signal. With evolving microwave and data acquisition technologies, full-band, ultrafast sweeps (<1 μs) will be realizable for ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗