Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “behavior”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Abrasion behavior of aluminum and composite skin coupons, stiffened skins and stiffened panels representative of transport airplane structures

A three-phase investigation was conducted to compare the friction and wear response of aluminum and graphite-epoxy composite materials when subjected to loading conditions similar to those experienced by the skin panels on the underside of a transport airplane during an emergency belly landing on a runway surface. The first phase involved a laboratory test which used a standard belt sander to provide the sliding abrasive surface. Small skin-coupon test specimens were abraded over a range of pressures and velocities to determine the effects of these variables on the coefficient of friction and wear rate. The second phase involved abrading I-beam stiffened skins on actual runway surface over the same range of pressures and velocities used in the first phase. In the third phase, large stiffened panels which most closely resembled transport fuelage skin construction were abraded on a runway surface. This report presents results from each phase of the investigation and shows comparisons between the friction and wear behavior of the aluminum and graphite-epoxy composite materials.

Jackson, K. E.↗
NASA NTRS1985

Understanding the Radiant Scattering Behavior of Vegetated Scenes

Knowledge of the physics of the scattering behavior of vegetation will ultimately serve the remote sensing and earth science community in many ways. For example, it will provide: (1) insight and guidance in developing new extraction techniques of canopy characteristics, (2) a basis for better interpretation of off-nadir satellite and aircraft data, (3) a basis for defining specifications of future earth observing sensor systems, and (4) a basis for defining important aspects of physical and biological processes of the plant system. The overall objective of the three-year study is to improve our fundamental understanding of the dynamics of directional scattering properties of vegetation canopies through analysis of field data and model simulation data. The specific objectives are to: (1) collect directional reflectance data covering the entire exitance hemisphere for several common vegetation canopies with various geometric structure (both homogeneous and row crop structures), (2) develop a scene radiation model with a general mathematical framework which will treat 3-D variability in heterogeneous scenes and account for 3-D radiant interactions within the scene, (3) conduct validations of the model on collected data sets, and (4) test and expand proposed physical scattering mechanisms involved in reflectance distribution dynamics by analyzing both field and modeling data.

Kimes, D. S.↗
NASA NTRS1985

Undercooling and solidification behavior in the InSb-Sb system

Use of the droplet emulsion technique has been successful in studying the undercooling and crystallization behavior of Sb, InSb, and an InSb-Sb eutectic alloy. Both droplet size and imposed cooling rate were influential in controlling the extent of liquid undercooling. The droplet surface coating was of significant importance in determining the resultant solidification product structure through its effect on nucleation kinetics. The maximum undercooling for pure Sb was extended from 0.08 to 0.23 T sub m. While simple crushing techniques provided a dramatic increase in droplet undercooling over the bulk material, emulsification treatments both enhanced this undercooling and allowed successful formation of a metastable simple cubic Sb phase. This phase was stable to temperatures approaching the melting point. The simple cubic phase was detected in droplet samples processed using DTA, air and water quenching, and drop tube processing under a helium gas atmosphere. A deviation in the InSb parent ingot composition limited interpretation of the line compound results, however, emulsification techniques extended the undercooling of this material to 0.17 T sub L and provided a stable, protective surface coating for the droplets. Emulsification of the eutectic alloy was effective at producing various levels of undercooling from 0.1 to 0.2 T sub E. Microstructural examination revealed a normal-type eutectic structure in the undercooled droplets indicating that solidification occurred within the coupled zone and that this zone is somewhat symmetric about the eutectic composition.

Graves, J. A.↗
NASA NTRS1986

Axial and torsional fatigue behavior of Waspaloy

The cyclic flow response and crack growth behavior of Waspaloy at room temperature and 650 C under tensile loading and torsional loading was studied, for two conditions of Waspaloy: fine grain, large gamma prime size; coarse grain, small gamma prime size. The fine grain material showed 5 to 10 percent hardening after about 10 percent of life, with sequent softening to failure at both themperature levels. The coarse grain material showed either stable response or monotonic softening to failure. Early crack initiation was observed on planes of maximum shear, with eventual branching to principle planes under torsional loading; cracks were always normal to load axis under tensile loading. Also, crack paths were intergranular at 650 C, mostly transgranular at room temperature.

Zamrik, S.↗
NASA NTRS1985

Fluid behavior in microgravity

An experiment designed to study some fundamental aspects of microgravity fluid dynamics has been built and is scheduled for flight. The purpose of the experiment is to investigate differences in behavior of wetting and nonwetting fluid systems at low Bond numbers. Methods were developed to determine liquid quantity, estimate vapor contact area and measure liquid layer thickness. Both the responses of the fluid systems to external perturbations and the transfer of liquid through a connection between two containers can be studied.

William W. Durgin↗
NASA NTRS1986

Effects of partial interlaminar bonding on impact resistance and loaded-hole behavior of graphite/epoxy quasi-isotropic laminates

A partial-bonding interlaminar toughening concept was evaluated for resistance to impact and for behavior of a loaded hole. Perforated Mylar sheets were interleaved between all 24 plies of a graphite/epoxy quasi-isotropic lay-up. Specimens were impacted by aluminum spheres while under tensile or compressive loads. Impact-failure thresholds and residual strengths were obtained. Loaded-hole specimens were tested in three configurations that were critical in bearing, shear, or tension. Partial bonding reduced the tensile and compressive strengths of undamaged specimens by about one-third. For impact, partial bonding did not change the threshold for impact failure under tensile preload. However, under compressive preload, partial bonding caused serious degradation of impact resistance. Partial bonding reduced the maximum load-carrying capacity of all three types of loaded-hole specimens. Overall, partial bonding degraded both impact resistance and bearing strength of holes.

Illg, W.↗
NASA NTRS1985

Atmospheric concentrations and behavior of halocarbons and methane

The atmospheric concentrations of halocarbons and methane in the troposphere and stratosphere were precisely measured by grab-sampling followed by gas-chromatographic analysis in the laboratory. Chlorofluorocarbons such as CCl2F2 and CCl3F have received a great deal of attention due to their probable impact on the stratospheric ozone: the chlorofluorocarbons accumulated in the troposphere are eventually decomposed by photolysis in the stratosphere releasing Cl radicals which in turn participate in the ClO sub x-catalytic chain destroying the ozone, especially in the upper stratosphere. Methane reacts with Cl in the stratosphere reducing the ozone depletion, while its source and future trend of concentration in the troposphere are uncertain. The study of their distribution and behavior in the atmosphere are therefore very important. After the extensive survey of the locations for collection of atmospheriic samples representing the midlatitudes Northern Hemisphere (N.H.) without local contamination, we have measured the concentrations of CCl2F2, CCl3F, CH3CCl3, CC1, CHCl=CCl2 and CCl2=CCl2 with plus or minus 1 pptv precision in samples collected in Hokkaido and west coast Tohoku area (the northern part of Japan, 40 deg to 45 deg N) every summer and winter since 1979. The observed concentrations of CCl2F2 and CCl3F are now above 360 and 200 pptv, respectively, and have been steadily increasing by approx. 15 and approx. 8 pptv/year during the last several years.

Makide, Y.↗
NASA NTRS1986

Compressive creep behavior of alloys based on B2 FeAl

Alloys based on FeAl are attractive alternate materials for environmental resistance at intermediate temperatures. Addition of small amounts of Nb, Hf, Ta, Mo, Zr, and B were shown to improve the compressive creep of this alloy at 1100 K. Boron, in particular, was found to have a synergistic effect along with Zr in providing properties substantially better than the binary alloy. This improvement seems to be related to the higher activation energy found for this alloy, suggesting a modification in the diffusion behavior due to the alloying additions.

Mantravadi, N.↗
NASA NTRS1986

The low cycle fatigue behavior of a plasma-sprayed coating material

Single crystal nickel-base superalloys employed in turbine blade applications are often used with a plasma spray coating for oxidation and hot corrosion resistance. These coatings may also affect fatigue life of the superalloy substrate. As part of a large program to understand the fatigue behavior of coated single crystals, fully reversed, total strain controlled fatigue tests were run on a free standing NiCoCrAlY coating alloy, PWA 276, at 0.1 Hz. Fatigue tests were conducted at 650 C, where the NiCoCrAlY alloy has modest ductility, and at 1050 C, where it is extremely ductile, showing tensile elongation in excess of 100 percent. At the lower test temperature, deformation induced disordering softened the NiCoCrAlY alloy, while at the higher test temperature cyclic hardening was observed which was linked to gradual coarsening of the two phase microstructure. Fatigue life of the NiCoCrAlY alloy was significantly longer at the higher temperature. Further, the life of the NiCoCrAlY alloy exceeds that of coated, /001/-oriented PWA 1480 single crystals at 1050 C, but at 650 C the life of the coated crystal is greater than that of the NiCoCrAlY alloy on a total strain basis.

Gayda, J.↗
NASA NTRS1985

Tropospheric ozone - Seasonal behavior, trends, and anthropogenic influence

In the present analysis of tropospheric ozone data, attention is given to spatial and temporal variations. Two modes of seasonal behavior are noted for surface ozone at mid-latitudes: a broad summer maximum within a few hundred km of industrial/urban areas in Europe and the U.S., and a minimum in summer or autumn in sparcely populated regions that are remote from industrial activity. These and limited historical data indicate that summertime concentrations of ozone near the surface in the rural areas of Europe and the U.S. may have increased between 20 and 100 percent since the 1940s. It is suggested that the summer maximum in ozone and other observed trends are due to photochemical production associated with anthropogenic emissions of NO(x), hydrocarbons, and CO from fossil fuel combustion.

Logan, J. A.↗
NASA NTRS1985

The effect of slots on the buckling and postbuckling behavior of laminated plates

An experimental study was conducted to evaluate the effect of lateral slots on the buckling response, the postbuckling response, and the failure characteristics of flat rectangular graphite-epoxy plates loaded in compression. The slots did not significantly affect the prebuckling and buckling behavior of the plates. The slots caused local changes in the strain distribution and out-of-plane deformations near the slot. Failure loads and modes were strongly affected by slot location. Centrally located slots did not affect the failure loads or failure modes of the plates. Slots located close to an unloaded edge of a plate reduced the postbuckling strength of the plate and affected the failure mode. For one slightly offset slot location, interaction of out-of-plane deformations with the slot tip was observed to affect the failure mode significantly without affecting the failure load.

Gurdal, Z.↗
NASA NTRS1985

Concentrations and behavior of oxygen and oxide ion in melts of composition CaO.MgO.xSiO2

The behavior of oxygen and oxide ion in silicate melts was investigated through their electrochemical reactions at a platinum electrode. Values are given for the diffusion coefficient for molecular oxygen in diopside melt and the activation energy of diffusion. It is shown that molecular oxygen dissociates prior to undergoing reduction and that oxide ion reacts quickly with silicate polymers when it is produced. The concentration of oxide ion is kept low by a buffering effect of the silicate, the exact level being dependent on the silicate composition. Data on the kinetics of reaction of the dissociation of molecular oxygen and on the buffering reactions are provided. It is demonstrated that the data on oxygen in these silicate melts are consistent with those for solid buffers.

Semkow, K. W.↗
NASA NTRS1984

The effects of simulator and aircraft motion on eye scan behavior

In a series of three experiments on the effects on eye-scan behavior of both simuator and aircraft motion, the sensitivity of an oculometric measure to motion effects was demonstrated. 'Fixation time', defined as the time the eyes spend at a particular location before moving on (saccade) to another fixation point, was found to be sensitive to motion effects in each of the experiments conducted. The results of the present study support the hypothesis that motion serves an alerting function, providing a 'cue' or 'clue' to the pilot that 'something happened'. The results do not support the hypothesis that direction of motion is conveyed through the type of motion information employed in these experiments.

Comstock, J. R., Jr.↗
NASA NTRS1986

On the behavior of hydromagnetic surface waves

The behavior of velocity, magnetic field, and pressure perturbations about a continuously varying interface in pressure equilibrium is investigated in detail within ideal incompressible magnetohydrodynamics. A specific initial value problem is solved in quadrature for a thin interface and compared with the solution for a discontinuous interface. The unattenuated surface wave about a discontinuous interface is replaced at a thin interface by a collective surface disturbance which decays, with the associated energy density flowing into local oscillations within the interface. At long times the envelope of the local oscillations is concentrated within a small fraction of the thin interface (gradients within the envelope increase linearly with time, eventually resulting in a breakdown of the linearized ideal theory). Thus, the derived decay rate of the surface disturbance gives a mode-conversion rate rather than a heating rate. In applications to the propagation and dissipation of surface waves in the solar corona, this rate cannot in general be interpreted as a coronal heating rate.

Lee, M. A.↗
NASA NTRS1986

Postbuckling behavior of selected graphite-epoxy cylindrical panels loaded in axial compression

Results of an experimental and analytical study of the postbuckling behavior of selected graphite-epoxy cylindrical panels loaded in axial compression are presented. The postbuckling response and failure characteristics of the panels are described. The postbuckling response of each specimen is typical of axially-compressed cylindrical shells and curved panels in that a severe reduction in load occurs at buckling. Failure of all panels initiated near regions with severe local bending gradients. Analytical results from a nonlinear general shell finite element analysis computer code correlate well with typical experimental results up to buckling. Measured initial geometric imperfections were included in the postbuckling analysis. Analytically-determined stress distributions in the postbuckling response were used with failure criteria to identify the load level and the location of first-ply failure.

Knight, N. F., Jr.↗
NASA NTRS1986

Behavior of a non-wetting melt in free fall - Experimental

To explain why nonwetting metals and semiconductors, directionally solidified in space, yield ingots which are smaller in diameter than the ampoule, the behavior of mercury during a parabolic free-fall in a KC135 aircraft was observed using transparent ampoules with attached video cameras. Triangular glass ampoules and cylindrical polycarbonate ampoules were filled to 30-95 percent capacity. In polycarbonate ampoules, mercury did not pull away from the ampoule walls. The photographs displayed either liquid columns separated by gas spaces or gas bubbles on the wall. At low levels of liquid, separated columns were favored, while only bubbles were seen when the liquid mercury almost filled the ampoule. In ampoules with triangular cross section, the liquid pulled away from the glass walls along the edges and contacted the walls along the centers, over about half of the wall width of each side.

Sen, R.↗
NASA NTRS1986

Growth behavior of surface cracks in the circumferential plane of solid and hollow cylinders

Experiments were conducted to study the growth behavior of surface fatigue cracks in the circumferential plane of solid and hollow cylinders. In the solid cylinders, the fatigue cracks were found to have a circular arc crack front with specific upper and lower limits to the arc radius. In the hollow cylinders, the fatigue cracks were found to agree accurately with the shape of a transformed semiellipse. A modification to the usual nondimensionalization expression used for surface flaws in flat plates was found to give correct trends for the hollow cylinder problem.

Forman, R. G.↗
NASA NTRS1986

The cyclic stress-strain behavior of a nickel-base superalloy at 650 C

It is pointed out that examinations of the monotonic tensile and fatigue behaviors of single crystal nickel-base superalloys have disclosed orientation-dependent tension-compression anisotropies and significant differences in the mechanical response of octahedral and cube slip at intermediate temperatures. An examination is conducted of the cyclic hardening response of the single crystal superalloy PWA 1480 at 650 C. In the considered case, tension-compression anisotropy is present, taking into account primarily conditions under which a single slip system is operative. Aspects of a deformation by single slip are considered along with cyclic hardening anisotropy in tension and compression. It is found that specimens deforming by octahedral slip on a single slip system have similar hardening responses in tensile and low cycle fatigue loading. Cyclic strain hardening is very low for specimens displaying single slip.

Gabb, T. P.↗