Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “angle control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72
All sourcesNASA NTRSDOE OSTI
NASA NTRS1935

Flight Tests of a Balanced Split Flap with Particular Reference to Rapid Operation

The flight path of a small parasol monoplane equipped with a special type of balanced split flap was determined for a series of glides during which the time taken to deflect or retract the flap was varied from 1 to 15 seconds in order to study the effect of the time taken to complete a flap movement on the motion of an airplane between the start of a flap movement and the attainment of steady flight with the new flap setting. For flap movements accompanied by a change of lift characteristics, and consequently of velocity, there is an appreciable delay in obtaining a desired change in glide angle even though the flap is operated instantaneously. Immediate control of the glide path is obtained only when the speed is maintained during the flap movement. When the speed is changed, the deviation from the desired path during the transition increases in proportion to the rapidity with which the flap is moved so that, with a high-lift flap, abrupt retraction at speeds less than the minimum speed with the flap retracted may be dangerous if practiced close to the ground.

Soule, H A↗
NASA NTRS1932

Further Flight Tests on the Effectiveness of Handley Page Automatic Control Slots

Investigation of damping in roll within range of maximum lift with the Albatross L 75, with and without Handley Page automatic control slots, revealed the following: Without control slots, any attempt to go beyond a certain angle of attack near c(sub a max) in glide and climb, is followed by sudden sideslip. The conduct of the airplane throughout the motions in roll, moreover, confirmed that all attempts to higher angles of attack are accompanied by sudden loss of damping in roll.

Pleines, Wilhelm↗
NASA NTRS1994

Powerful Electromechanical Linear Actuator

Powerful electromechanical linear actuator designed to replace hydraulic actuator that provides incremental linear movements to large object and holds its position against heavy loads. Electromechanical actuator cleaner and simpler, and needs less maintenance. Two principal innovative features that distinguish new actuator are use of shaft-angle resolver as source of position feedback to electronic control subsystem and antibacklash gearing arrangement.

Cowan, John R.↗
NASA NTRS1993

Single-input/single-output transfer functions for a flexible slewing link

Truncated linear models based on constrained and unconstrained mode expansions for a flexible link with torque actuation at its hub led us to examine the behavior of the open-loop-zeros of five commonly used SISO transfer functions. We arrive at new conclusions with regard to minimum- and non-minimum-phase zeros, and passivity of the transfer functions. The flexible-to-rigid inertia (FRI) ratio plays an important role in the determination of these characteristics. This paper illustrates how the zero locations of some of the transfer functions are dramatically affected by the FRI ratio. We also investigate the performance of a hub angle, hub rate, and relative tip position static feedback controller based on a reduced-order constrained mode model when applied to both unconstrained and constrained mode models of the same dimension. Simulations indicate that the constrained model can be stable while the unconstrained model is not for high FRI ratios. Our findings can provide useful information to designers in cases where the controller is sensitive to the 1ocation of the plant's zeros.

Barbieri, Enrique↗
NASA NTRS1996

Aeroservoelastic Modeling and Validation of a Thrust-Vectoring F/A-18 Aircraft

An F/A-18 aircraft was modified to perform flight research at high angles of attack (AOA) using thrust vectoring and advanced control law concepts for agility and performance enhancement and to provide a testbed for the computational fluid dynamics community. Aeroservoelastic (ASE) characteristics had changed considerably from the baseline F/A-18 aircraft because of structural and flight control system amendments, so analyses and flight tests were performed to verify structural stability at high AOA. Detailed actuator models that consider the physical, electrical, and mechanical elements of actuation and its installation on the airframe were employed in the analysis to accurately model the coupled dynamics of the airframe, actuators, and control surfaces. This report describes the ASE modeling procedure, ground test validation, flight test clearance, and test data analysis for the reconfigured F/A-18 aircraft. Multivariable ASE stability margins are calculated from flight data and compared to analytical margins. Because this thrust-vectoring configuration uses exhaust vanes to vector the thrust, the modeling issues are nearly identical for modem multi-axis nozzle configurations. This report correlates analysis results with flight test data and makes observations concerning the application of the linear predictions to thrust-vectoring and high-AOA flight.

Brenner, Martin J.↗
NASA NTRS1959

Flight Behavior of the X-2 Research Airplane to a Mach Number of 3.20 and a Geometric Altitude of 126,200 Feet

The maximum Mach number and altitude capabilities of the Bell X-2 research airplane were achieved during a program conducted by the U.S. Air Force with Bell Aircraft Corp. providing operational support and the National Aeronautics and Space Administration providing instrumentation and advisory engineering assistance. A maximum geometric altitude of 126,200 feet was attained at a static pressure of 9.4 pounds per square foot and a dynamic pressure of 19.1 pounds per square foot. During the last flight of the airplane, a maximum Mach number of 3.20 was reached. The directionally divergent maneuver which terminated the final high Mach number flight was precipitated by the loss in directional stability that resulted from increasing the angle of attack. The yawing moment from the lateral control was sufficient to initiate the divergence and also to cause,, indirectly, rolling moments that were greater than the aileron capabilities of the airplane. The ensuing violent motions-resulting from inertial roll coupling caused the loss of the aircraft.

Day, Richard E.↗
NASA NTRS1959

Launch, Low-Speed, and Landing Characteristics Determined from the First Flight of the North American X-15 Research Airplane

The first flight of the North American X-15 research airplane was made on June 8, 1959. This was accomplished after completion of a series of captive flights with the X-15 attached to the B-52 carrier airplane to demonstrate the aerodynamic and systems compatibility of the X-15//B-52 combination and the X-15 subsystem operation. This flight was planned as a glide flight so that the pilot need not be concerned with the propulsion system. Discussions of the launch, low-speed maneuvering, and landing characteristics are presented, and the results are compared with predictions from preflight studies. The launch characteristics were generally satisfactory, and the X-15 vertical tail adequately cleared the B-52 wing cutout. The actual landing pattern and landing characteristics compared favorably with predictions, and the recommended landing technique of lowering the flaps and landing gear at a low altitude appears to be a satisfactory method of landing the X-15 airplane. There was a quantitative correlation between flight-measured and predicted lift-drag-ratio characteristics in the clean configuration and a qualitative correlation in the landing configuration. A longitudinal-controllability problem, which became severe in the landing configuration, was evident throughout the flight and, apparently, was aggravated by the sensitivity of the side-located control stick. In the low-to-moderate angle-of-attack range covered, the longitudinal and directional stability were indicated to be adequate.

Finch, Thomas W.↗
NASA NTRS1983

Vertical flight path steering system for aircraft

Disclosed is a vertical flight path angle steering system for aircraft, utilizing a digital flight control computer which processes pilot control inputs and aircraft response parameters into suitable elevator commands and control information for display to the pilot on a cathode ray tube. The system yields desirable airplane control handling qualities and responses as well as improvements in pilot workload and safety during airplane operation in the terminal area and under windshear conditions.

Lambregts, Antonius A.↗
NASA NTRS1989

Nozzle fabrication technique

A block of electrically-conductive material which is to be formed into a body with internal and/or external surfaces that approximate hyperboloids of one sheet is placed so that its axis is set at a predetermined skew angle with relation to a travelling EDM electrode wire and the electrode wire is then moved into cutting proximity of the body. Thereafter, by revolving the body about its own axis, the external and/or internal surfaces of the body will be cut into an approximate hyperbolic surface of revolution depending upon whether the body is positioned with the cutting wire outside of the body or in a previously-formed longitudinal passage in the body. As an alternative technique, elongated channels can also be cut into the walls of the body by successively orienting the body to a selected number of angular positions with the electrode wire being either outside of the body or in a previously-formed passage in the body. At each of these angular positions, the electrode wire is moved orthogonally with respect to the axis of the wire while both the body axis skew angle and the rotational position about that axis are controlled for cutting a channel or groove in the body as required to relieve stresses in the material of the body or to convey a coolant fluid.

Wells, Dennis L.↗
NASA NTRS2009

Pitch-Axis Aerodynamic Parameter Identification for NASA's F-15B

As part of NASA s Intelligent Flight Control Systems program, parameter identification experiments were carried out with NASA Dryden s F-15B TN 837 aircraft. The canard control surfaces, whose movement is highly correlated with aircraft angle of attack, and the aircraft s aerodynamic instability in the pitch axis contribute to making parameter identification challenging. The equation-error method of analysis is applied to several longitudinal parameter identification maneuvers and a new approach for compensating for flight-data signal time lags is developed, which improves the accuracy and consistency of the results.

Woodruff, Stephen L.↗
NASA NTRS2014

Numerical Simulation of a High-Lift Configuration with Embedded Fluidic Actuators

Numerical simulations have been performed for a vertical tail configuration with deflected rudder. The suction surface of the main element of this configuration is embedded with an array of 32 fluidic actuators that produce oscillating sweeping jets. Such oscillating jets have been found to be very effective for flow control applications in the past. In the current paper, a high-fidelity computational fluid dynamics (CFD) code known as the PowerFLOW(Registered TradeMark) code is used to simulate the entire flow field associated with this configuration, including the flow inside the actuators. The computed results for the surface pressure and integrated forces compare favorably with measured data. In addition, numerical solutions predict the correct trends in forces with active flow control compared to the no control case. Effect of varying yaw and rudder deflection angles are also presented. In addition, computations have been performed at a higher Reynolds number to assess the performance of fluidic actuators at flight conditions.

Vatsa, Veer N.↗
NASA NTRS2016

Numerical Simulation of a High-Lift Configuration Embedded with High Momentum Fluidic Actuators

Numerical simulations have been performed for a vertical tail configuration with deflected rudder. The suction surface of the main element of this configuration, just upstream of the hinge line, is embedded with an array of 32 fluidic actuators that produce oscillating sweeping jets. Such oscillating jets have been found to be very effective for flow control applications in the past. In the current paper, a high-fidelity computational fluid dynamics (CFD) code known as the PowerFLOW R code is used to simulate the entire flow field associated with this configuration, including the flow inside the actuators. A fully compressible version of the PowerFLOW R code valid for high speed flows is used for the present simulations to accurately represent the transonic flow regimes encountered in the flow field due to the actuators operating at higher mass flow (momentum) rates required to mitigate reverse flow regions on a highly-deflected rudder surface. The computed results for the surface pressure and integrated forces compare favorably with measured data. In addition, numerical solutions predict the correct trends in forces with active flow control compared to the no control case. The effect of varying the rudder deflection angle on integrated forces and surface pressures is also presented.

Vatsa, Veer N.↗
NASA NTRSDate not supplied

Aerosol Wind Profiler (AWP) Doppler Wind Lidar Airborne Observations During the NOAA Joint Venture 3-D Wind Measurement Demonstration and NASA Active-Passive Profiling Experiment (APEX)

The NASA Langley Research Center (LaRC) has recently completed development of the Aerosol Wind Profiler (AWP) airborne Doppler wind lidar (DWL) instrument. AWP was supported by the NASA Earth Science Technology Office and the Earth Science Division, a project that adapted the Wind-Space Pathfinder (Wind-SP) DWL transceiver onto a structure for flight aboard a variety of NASA research aircraft. AWP demonstrates many technologies required for a space DWL mission, including a coherent-detection, optical heterodyne laser transmitter with high pulse energy (up to ~55 mJ) and repetition rate (200 Hz), electronic control of the beam path allowing for multiple viewing angles (allowing vector wind measurements) with no moving parts, compact highly-stable and tunable reference lasers allowing for high-precision measurement of velocity at long ranges while mitigating the impact of satellite platform velocity, and many others. AWP represents NASA’s only currently operational airborne 3-D wind profiling sensor. NASA LaRC was selected by the NOAA Joint Venture (JV) program to conduct a suborbital 3-D Wind measurement campaign demonstrate how data from a coherent-detection DWL like AWP could serve NOAA’s weather analysis and forecasting needs. The NOAA JV program is designed to work with the private sector, academia and other federal agencies to explore the feasibility and capability of emerging technologies spacecraft and other mission-specific tools to meet NOAA’s mission requirements. AWP was initially demonstrated on the NASA DC-8 within this JV program in October 2023, piggybacking on the NASA EcoDemonstrator mission focused on in-situ sampling of jet aircraft emissions and contrail formation from Everett, Washington. The in-situ sampling resulted in very frequent and rapid aircraft attitude changes which unfortunately degraded AWP data quality. But, during times with level flight and AVAPS dropsonde operations, AWP demonstrated excellent precision (< 2 m/s RMS) with high vertical (< 100 meter) resolution and 2 km spacing between profiles. AWP will be flown again on the NASA LaRC Gulfstream-3 from mid-September to mid-October 2024 out of Hampton, VA to complete the NOAA JV 3-D wind demonstration. Additional AWP flights will occur in early November from southern California during the NASA Active-Passive Profiling Experiment (APEX), focused on underflights of the NASA ER-2 equipped with many atmospheric profiling sensors. This presentation will summarize AWP measurements collected during these two fall 2024 flight campaigns, and how the AWP data compares with AVAPS dropsonde, NOAA weather prediction model, and GOES atmospheric motion vector data.

Kristopher Bedka↗
NASA NTRS1993

Visual cueing considerations in Nap-of-the-Earth helicopter flight head-slaved helmet-mounted displays

The pilot's ability to derive Control-Oriented Visual Field Information from teleoperated Helmet-Mounted displays in Nap-of-the-Earth flight, is investigated. The visual field with these types of displays, commonly used in Apache and Cobra helicopter night operations, originates from a relatively narrow field-of-view Forward Looking Infrared Radiation Camera, gimbal-mounted at the nose of the aircraft and slaved to the pilot's line-of-sight, in order to obtain a wide-angle field-of-regard. Pilots have encountered considerable difficulties in controlling the aircraft by these devices. Experimental simulator results presented here indicate that part of these difficulties can be attributed to head/camera slaving system phase lags and errors. In the presence of voluntary head rotation, these slaving system imperfections are shown to impair the Control-Oriented Visual Field Information vital in vehicular control, such as the perception of the anticipated flight path or the vehicle yaw rate. Since, in the presence of slaving system imperfections, the pilot will tend to minimize head rotation, the full wide-angle field-of-regard of the line-of-sight slaved Helmet-Mounted Display, is not always fully utilized.

Grunwald, Arthur J.↗
NASA NTRS1995

Contingency maneuver strategies for the Total Ozone Mapping Spectrometer-Earth Probe (TOMS-EP)

The Total Ozone Mapping Spectrometer-Earth Probe (TOMS-EP) is a polar-orbiting spacecraft designed to measure total ozone levels in the Earth's atmosphere. The nominal mission orbit is a 955-kilometer circular Sun-synchronous orbit with an ascending node mean local crossing time (MLT) between 11:02 a.m. and 11:25 a.m. These two mean local ascending node times constitute the boundaries of the MLT box for this mission. The MLT boundaries were chosen to maintain the Sun-to-Earth-to-vehicle orbit-normal (SVN) angle within a preselected set of seasonally independent boundaries. Because the SVN angle is seasonally dependent, but the MLT is not, contingency options for correcting the MLT of orbital states that fall outside of the required MLT range become time dependent. This paper focuses on contingency orbit adjustment strategies developed at the Goddard Space Flight Center (GSFC) Flight Dynamics Division (FDD) during the mission planning phase of TOMS-EP. Time-dependent delta-V strategies are presented for correcting mission orbit states lying outside of the MLT range. Typically, passive control of the MLT drift rate can be used to restore the orbit state to the required MLT before a seasonal violation of SVN angle constraints can occur. Passive control of the MLT drift rate is obtained through adjustment of the semimajor axis and/or the inclination. The time between initial arrival on orbit at an 'out-of-the box' MLT state and violation of the SVN angle constraints is always less than or equal to 1 year. The choice of which parameter(s) to adjust is dictated by the duration of this time period, the desired mission lifetime, the delta-V cost, and operational constraints.

Kestler, James↗
NASA NTRS1979

Aerodynamic interactions from reaction controls for lateral control of the M2-F2 lifting-body entry configuration at transonic and supersonic and supersonic Mach numbers

Tests were conducted in the Ames 6 by 6 foot wind tunnel to determine the interaction of reaction jets for roll control on the M2-F2 lifting-body entry vehicle. Moment interactions are presented for a Mach number range of 0.6 to 1.7, a Reynolds number range of 1.2 x 10 to the 6th power to 1.6 x 10 to the 6th power (based on model reference length), an angle-of-attack range of -9 deg to 20 deg, and an angle-of-sideslip range of -6 deg to 6 deg at an angle of attack of 6 deg. The reaction jets produce roll control with small adverse yawing moment, which can be offset by horizontal thrust component of canted jets.

Bailey, R. O.↗
NASA NTRS1994

In Operation Detection and Correction of Rotor Imbalance in Jet Engines Using Active Vibration Control

Jet Engines may experience severe vibration due to the sudden imbalance caused by blade failure. This research investigates employment of on board magnetic bearings or piezoelectric actuators to cancel these forces in flight. This operation requires identification of the source of the vibrations via an expert system, determination of the required phase angles and amplitudes for the correction forces, and application of the desired control signals to the magnetic bearings or piezo electric actuators. This paper will show the architecture of the software system, details of the control algorithm used for the sudden imbalance correction project described above, and the laboratory test results.

Manchala, Daniel W.↗
NASA NTRS2023

Broadband and Wide Angle Nonreciprocal Thermal Emission from Weyl Semimetal Structures

Nonreciprocal thermal emission is a cutting-edge technology that enables fundamental control over thermal radiation and has exciting applications in thermal energy harvesting. However, so far one of the foremost challenges is making nonreciprocal emission to operate over a broad wavelength range and for multiple angles. In this work, we solve this outstanding problem by proposing three different types of structures always utilizing only one Weyl semimetal (WSM) thin film combined with one or two additional dielectric or metallic layers and terminated by a metallic substrate. First a tradeoff relationship between the magnitude and bandwidth of the thermal nonreciprocity contrast is established based on the thickness of the WSM film. Then, the bandwidth broadening effect is demonstrated via the insertion of a dielectric spacer layer that can also be fine-tuned by varying its thickness. Finally, further control on the resulting strong nonreciprocal thermal radiation is demonstrated by the addition of a thin metallic layer in the proposed few layer designs. The presented composite structures work for a broad frequency range and multiple emission angles, consisting highly advantageous properties to various nonreciprocal thermal radiation applications. Moreover, the proposed designs do not require any patterning and can be experimentally realized by simple deposition fabrication methods. They are expected to aid in the creation of broadband nonreciprocal thermal emitters that can find applications in new energy harvesting devices.

Andrew Butler↗