Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TUNNEL EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

The effects on cruise drag of installing long-duct refan-engine nacelles on the McDonnell Douglas DC-8-50 and -61

A high-speed wind tunnel test was conducted to determine the effect on cruise performance of installing long-duct refan-engine nacelles on the DC-8-50 and -61 models. Drag data and wing/pylon/nacelle channel pressure data are presented. At a typical cruise condition there exists a very small interference drag penalty of less than one-percent of total cruise data for the Refan installation. Pressure data indicate that some supersonic flow is present in the inboard channel of the inboard refan nacelle installation, but it is not sufficient to cause any wave drag on boundary layer separation. One pylon modification, which takes the form of pylon bumps, was tested. It resulted in a drag penalty, because its design goal of eliminating shock-related interference drag was not required and the bump thus became a source of additional parasite drag.

Callaghan, J. T.↗
NASA NTRS1988

Tip-path-plane angle effects on rotor blade-vortex interaction noise levels and directivity

Acoustic data of a scale model BO-105 main rotor acquired in a large aeroacoustic wind tunnel are presented to investigate the parametric effects of rotor operating conditions on blade-vortex interaction (BVI) impulsive noise. Contours of a BVI noise metric are employed to quantify the effects of rotor advance ratio and tip-path-plane angle on BVI noise directivity and amplitude. Acoustic time history data are presented to illustrate the variations in impulsive characteristics. The directionality, noise levels and impulsive content of both advancing and retreating side BVI are shown to vary significantly with tip-path-plane angle and advance ratio over the range of low and moderate flight speeds considered.

Burley, Casey L.↗
NASA NTRS1932

Increase in the maximum lift of an airplane wing due to a sudden increase in its effective angle of attack resulting from a gust

Wind-tunnel tests are described, in which the angle of attack of a wing model was suddenly increased (producing the effect of a vertical gust) and the resulting forces were measured. It was found that the maximum lift coefficient increases in proportion to the rate of increase in the angle of attack. This fact is important for the determination of the gust stresses of airplanes with low wing loading. The results of the calculation of the corrective factor are given for a high-performance glider and a light sport plane of conventional type.

Kramer, Max↗
NASA NTRS1950

Investigation at Low Speeds of the Effect of Aspect Ratio and Sweep on Rolling Stability Derivatives of Untapered Wings

A low-scale wind-tunnel investigation was conducted in rolling flow to determine the effects of aspect ratio and sweep (when varied independently) on the rolling stability derivatives for a series of untapered wings. The rolling-flow equipment of the Langley stability tunnel was used for the tests. The data of the investigation have been used to develop a method of accounting for the effects of the drag on the yawing moment due to rolling throughout the lift range.

Goodman, Alex↗
NASA NTRS1986

Design and calibration of the carousel wind tunnel

In the study of planetary aeolian processes the effect of gravity is not readily modeled. Gravity appears in the equations of particle motion along with interparticle forces but the two terms are not separable. A wind tunnel that would permit variable gravity would allow separation of the forces and aid greatly in understanding planetary aeolian processes. The design Carousel Wind Tunnel (CWT) allows for a long flow distance in a small sized tunnel since the test section is a continuo us circuit and allows for a variable pseudo gravity. A prototype design was built and calibrated to gain some understanding of the characteristics of the design and the results presented.

Leach, R. N.↗
NASA NTRS1987

Design and calibration of the carousel wind tunnel

In the study of planetary aeolian processes the effect of gravity is not readily modeled. Gravity appears in the equations of particle motion along with interparticle forces but the two terms are not separable. A wind tunnel that would permit variable gravity would allow separation of the forces and aid greatly in understanding planetary aeolian processes. The design of the Carousel Wind Tunnel (CWT) allows for a long flow distance in a small sized tunnel since the test section is a continuous circuit and allows for a variable pseudo-gravity. A prototype design was built and calibrated to gain some understanding of the characteristics of the design and the results presented.

Leach, R. N.↗
NASA NTRS2009

SMART Rotor Development and Wind-Tunnel Test

Boeing and a team from Air Force, NASA, Army, Massachusetts Institute of Technology, University of California at Los Angeles, and University of Maryland have successfully completed a wind-tunnel test of the smart material actuated rotor technology (SMART) rotor in the 40- by 80-foot wind-tunnel of the National Full-Scale Aerodynamic Complex at NASA Ames Research Center, figure 1. The SMART rotor is a full-scale, five-bladed bearingless MD 900 helicopter rotor modified with a piezoelectric-actuated trailing-edge flap on each blade. The development effort included design, fabrication, and component testing of the rotor blades, the trailing-edge flaps, the piezoelectric actuators, the switching power amplifiers, the actuator control system, and the data/power system. Development of the smart rotor culminated in a whirl-tower hover test which demonstrated the functionality, robustness, and required authority of the active flap system. The eleven-week wind tunnel test program evaluated the forward flight characteristics of the active-flap rotor, gathered data to validate state-of-the-art codes for rotor noise analysis, and quantified the effects of open- and closed-loop active-flap control on rotor loads, noise, and performance. The test demonstrated on-blade smart material control of flaps on a full-scale rotor for the first time in a wind tunnel. The effectiveness and the reliability of the flap actuation system were successfully demonstrated in more than 60 hours of wind-tunnel testing. The data acquired and lessons learned will be instrumental in maturing this technology and transitioning it into production. The development effort, test hardware, wind-tunnel test program, and test results will be presented in the full paper.

Lau, Benton H.↗
NASA NTRS1975

A linear solution of lift interference in square tunnels with slotted test sections of finite length

A numerical program has been developed to determine the effects on lift interference of the finite length of the slotted portion of a square tunnel. Also analyzed by the program are the effects produced by small variations of static pressure between upper and lower plenum, and by boundary layer development on upper and lower walls downstream of the slotted section. In the flow model, based on compressible linear theory, the wing is represented by a single vortex and the wall induced perturbations are obtained by superimposing the effects of a series of images of the central vortex and of a distribution of sources and sinks on panels along the tunnel walls. The present results can be indicative of the magnitude and of the trends of the interference patterns associated with slotted test sections of finite length at high subsonic Mach numbers.

Ruger, C.↗
NASA NTRS1992

Propulsion simulator for magnetically-suspended wind tunnel models

In order to demonstrate the measurement of aerodynamic forces/moments, including the effects of exhaust jets in Magnetic Suspension and Balance System (MSBS) wind tunnels, two propulsion simulator models were developed at Physical Sciences Inc. (PSI). Both the small-scale model (1 in. diameter X 8 in. long) and the large-scale model (2.5 in. diameter X 15 in. long) employed compressed, liquefied carbon dioxide as a propellant. The small-scale simulator, made from a highly magnetizable iron alloy, was demonstrated in the 7 in. MSBS wind tunnel at the University of Southampton. It developed a maximum thrust of approximate 1.3 lbf with a 0.098 in. diameter nozzle and 0.7 lbf with a 0.295 in. diameter nozzle. The Southampton MSBS was able to control the simulator at angles-of attack up to 20 deg. The large-scale simulator was demonstrated to operate in both a steady-state and a pulse mode via a miniaturized solinoid valve. It developed a stable and repeatable thrust of 2.75 lbf over a period of 4s and a nozzle pressure ratio (NPR) of 5.

Joshi, P. B.↗
NASA NTRS1995

An assessment of viscous effects in computational simulation of benign and burst vortex flows on generic fighter wind-tunnel models using TEAM code

Vortex flows on a twin-tail and a single-tail modular transonic vortex interaction (MTVI) model, representative of a generic fighter configuration, are computationally simulated in this study using the Three-dimensional Euler/Navier-Stokes Aerodynamic Method (TEAM). The primary objective is to provide an assessment of viscous effects on benign (10 deg angle of attack) and burst (35 deg angle of attack) vortex flow solutions. This study was conducted in support of a NASA project aimed at assessing the viability of using Euler technology to predict aerodynamic characteristics of aircraft configurations at moderate-to-high angles of attack in a preliminary design environment. The TEAM code solves the Euler and Reynolds-average Navier-Stokes equations on patched multiblock structured grids. Its algorithm is based on a cell-centered finite-volume formulation with multistage time-stepping scheme. Viscous effects are assessed by comparing the computed inviscid and viscous solutions with each other and experimental data. Also, results of Euler solution sensitivity to grid density and numerical dissipation are presented for the twin-tail model. The results show that proper accounting of viscous effects is necessary for detailed design and optimization but Euler solutions can provide meaningful guidelines for preliminary design of flight vehicles which exhibit vortex flows in parts of their flight envelope.

Kinard, Tim A.↗
NASA NTRS1973

The effects on cruise drag of installing refan-engine nacelles on the McDonnell-Douglas DC-9

A high speed wind tunnel test has been conducted to determine the effect on cruise drag for installing larger JT8D Refan engine nacelles on the Douglas DC-9. Drag data and wing- and nacelle/pylon/fuselage-channel pressure data are presented. Reduced pylon spares, required to minimize effects of the nacelle installation on low-speed deep stall, were investigated. The reduce span pylons resulted in no adverse interference effects. At typical cruise Mach numbers the measured penalty for the Refan installation was less than estimated due to a favorable effect of the larger entering engine stream tube suppressing the wing upper-surface velocities with subsequent wing compressibility drag reduction. Channel pressures show no shock waves or boundary layer separations.

Callaghan, J. T.↗
NASA NTRS1996

Development of a Driver Code for the WICS Project

Wall Interference Correction System (WICS) is a computational technique to evaluate the wind tunnel wall interference corrections for blockage, Mach number, dynamic pressure and angle of attack. The objective is to predict the effects of the bounding walls on wind tunnel measurements [1]. The procedure attempts to compute these corrections in real time so that the test engineer can implement these by adjusting wind tunnel controls for angle of attack and dynamic pressure while the test is in progress in the 12 ft. pressure wind tunnel at the Ames Research Center. The technique utilizes an ideal flow solver PMARC (Panel Method developed at the Ames Research Center) to compute influence coefficients in an internal flow mode by representing a paneled model of the tunnel for fullspan and semispan tests.

Ghosh, Amitabha↗
NASA NTRS2002

Design and Development of a Deep Acoustic Lining for the 40-by 80-Foot Wind Tunnel Test Section

The work described in this report has made effective use of design teams to build a state-of-the-art anechoic wind-tunnel facility. Many potential design solutions were evaluated using engineering analysis, and computational tools. Design alternatives were then evaluated using specially developed testing techniques, Large-scale coupon testing was then performed to develop confidence that the preferred design would meet the acoustic, aerodynamic, and structural objectives of the project. Finally, designs were frozen and the final product was installed in the wind tunnel. The result of this technically ambitious project has been the creation of a unique acoustic wind tunnel. Its large test section (39 ft x 79 ft x SO ft), potentially near-anechoic environment, and medium subsonic speed capability (M = 0.45) will support a full range of aeroacoustic testing-from rotorcraft and other vertical takeoff and landing aircraft to the take-off/landing configurations of both subsonic and supersonic transports.

Soderman, Paul T.↗
DOE OSTI2023

Numerical quantum clock simulations for measuring tunneling times

Here, we numerically study two methods of measuring tunneling times using a quantum clock. In the conventional method using the Larmor clock, we show that the Larmor tunneling time can be shorter for higher tunneling barriers. In the second method, we study the probability of a spin-flip of a particle when it is transmitted through a potential barrier including a spatially rotating field interacting with its spin. According to the adiabatic theorem, the probability depends on the velocity of the particle inside the barrier. It is numerically observed that the probability increases for higher barriers, which is consistent with the result obtained by the Larmor clock. By comparing outcomes for different initial spin states, we suggest that one of the main causes of the apparent decrease in the tunneling time can be the filtering effect occurring at the end of the barrier.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1979

U.S. aerospace industry opinion of the effect of computer-aided prediction-design technology on future wind-tunnel test requirements for aircraft development programs

A survey of the U.S. aerospace industry in late 1977 suggests that there will be an increasing use of computer-aided prediction-design technology (CPD Tech) in the aircraft development process but that, overall, only a modest reduction in wind-tunnel test requirements from the current level is expected in the period through 1995. Opinions were received from key spokesmen in 23 of the 26 solicited major companies or corporate divisions involved in the design and manufacture of nonrotary wing aircraft. Development programs for nine types of aircraft related to test phases and wind-tunnel size and speed range were considered.

Treon, S. L.↗
NASA NTRS1983

A review of preflight estimates of real-gas effects on space shuttle aerodynamic characteristics

Preflight estimates of the hypersonic aerodynamic characteristics of the Shuttle orbiter were based on a diverse series of research studies using state of the art techniques developed by basic research in the 60's and 70's. Real-gas viscous calculations on simple shapes that were used to evaluate correlation parameters indicated that real-gas effects reduce aerodynamic forces and moments. Inviscid calculations on winged lifting shapes indicated reduced forces and a slight nose-up pitch resulted because of real-gas effects. Analysis of the extensive wind tunnel data base indicated viscous correlation parameters provided the most appropriate extrapolation technique for estimating flight aerodynamics. Variations because of changes in the ratio of specific heats, which was the only available experimental tool for evaluating real-gas effects, indicated that reduced loads and nose-up pitching moments would occur at high altitudes and Mach numbers but that the values would not exceed the tolerances and variations established about the aerodynamic design data book values derived from viscous correlations. During STS-1, nose-up pitching moments exceeded the established variations.

Woods, W. C.↗