Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Surfaced Polymers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

Surface contamination on LDEF exposed materials

X-ray photoelectron spectroscopy (XPS) has been used to study the surface composition and chemistry of Long Duration Exposure Facility (LDEF) exposed materials including silvered Teflon (Ag/FEP), Kapton, S13GLO paint, quartz crystal monitors (QCM's), carbon fiber/organic matrix composites, and carbon fiber/Al Alloy composites. In each set of samples, silicones were the major contributors to the molecular film accumulated on the LDEF exposed surfaces. All surfaces analyzed have been contaminated with Si, O, and C; most have low levels (less than 1 atom percent) of N, S, and F. Occasionally observed contaminants included Cl, Na, K, P, and various metals. Orange/brown discoloration observed near vent slots in some Ag/FEP blankets were higher in carbon, sulfur, and nitrogen relative to other contamination types. The source of contamination has not been identified, but amine/amide functionalities were detected. It is probable that this same source of contamination account for the low levels of sulfur and nitrogen observed on most LDEF exposed surfaces. XPS, which probes 50 to 100 A in depth, detected the major sample components underneath the contaminant film in every analysis. This probably indicates that the contaminant overlayer is patchy, with significant areas covered by less that 100 A of molecular film. Energy dispersive x-ray spectroscopy (EDS) of LDEF exposed surfaces during secondary electron microscopy (SEM) of the samples confirmed contamination of the surfaces with Si and O. In general, particulates were not observed to develop from the contaminant overlayer on the exposed LDEF material surfaces. However, many SiO2 submicron particles were seen on a masked edge of an Ag/FEP blanket. In some cases such as the carbon fiber/organic matrix composites, interpretation of the contamination data was hindered by the lack of good laboratory controls. Examination of laboratory controls for the carbon fiber/Al alloy composites showed that preflight contamination was the most significant factor for all the contaminants generally detected at less than 1 atom percent, or detected only occasionally (i.e., all but Si, O, and C). Flight control surfaces, including sample backsides not exposed to space radiation or atomic oxygen flux, have accumulated some contamination on flight (compared to laboratory controls), but experimentally, the LDEF exposed surface contamination levels are generally higher for the contaminants Si and O. For most materials analyzed, Si contamination levels were higher on the leading edge surfaces than on the trailing edge surfaces. This was true even for the composite samples where considerable atomic oxygen erosion of the leading edge surfaces was observed by SEM. It is probable that the return flux associated with atmospheric backscatter resulted in enhanced deposition of silicones and other contaminants on the leading edge flight surfaces relative to the trailing edge. Although the Si concentration data suggested greater on-flight deposition of contaminants on the leading edge surfaces, the XPS analyses did not conclusively show different relative total thicknesses of flight deposited contamination for leading and trailing edge surfaces. It is possible that atomic oxygen reactions on the leading edge resulted in greater volatilization of the carbon component of the deposited silicones, effectively 'thinning' the leading edge deposited overlayer. Unlike other materials, exposed polymers such as Kapton and FEP-type Teflon had very low contamination on the leading edge surfaces. SEM evidence showed that undercutting of the contaminant overlayer and damaged polymer layers occurred during atomic oxygen erosion, which would enhance loss of material from the exposed surface.

Hemminger, Carol S.↗

Effect of Viscosity on the Microformability of Bulk Amorphous Alloy in Supercooled Liquid Region

Previously published results have shown that viscosity greatly influences on the deformation behavior of the bulk amorphous alloy in supercooled liquid region during microforming process. And viscosity is proved to be a component of the evaluation index which indicating microformability. Based on the fluid flow theory and assumptions, bulk amorphous alloy can be regarded as the viscous materials with a certain viscosity. It is helpful to understand how the viscosity plays an important role in viscous materials with various viscosities by numerical simulation on the process. Analysis is carried out by linear state equation in FEM with other three materials, water, lubricant oil and polymer melt, whose viscosities are different obviously. The depths of the materials flow into the U-shaped groove during the microimprinting process are compared in this paper. The result shows that the deformation is quite different when surface tension effect is not considered in the case. With the lowest viscosity, water can reach the bottom of micro groove in a very short time. Lubricant oil and polymer melt slower than it. Moreover bulk amorphous alloys in supercooled liquid state just flow into the groove slightly. Among the alloys of different systems including Pd-, Mg- and Zr-based alloy, Pd-based alloy ranks largest in the depth. Mg-based alloy is the second. And Zr-based alloy is the third. Further more the rank order of the viscosities of the alloys is Pd-, Mg- and Zr-based. It agrees well with the results of calculation. Therefore viscosity plays an important role in the microforming of the bulk amorphous alloy in the supercooled liquid state.

36 MATERIALS SCIENCE↗

Confinement-induced chirality in phase-separated achiral polymer solutions

Self-organization of polymers in constrained geometries largely determines their applications in high-strength materials, photonics, and electronics. Chiral organization under confinement is well established for polymers with intrinsic molecular chirality; however, it has not been observed for achiral polymers. Here, we report the emergence of chirality in spatially confined solutions of achiral rigid-rod polymers. We show that kinetically arrested phase separation of polymer solutions confined to narrow capillaries resulted in alternating segments of isotropic and chiral nematic phases. The chiral structure of the nematic segments originated from the interplay between the constrained geometry, surface anchoring, orientational wetting, and elastic anisotropy of rigid-rod polymers. The catenoidal shape of the chiral structure recapitulated the morphology of biological chiral structures. These findings provide insight into the organization of soft matter under spatial confinement and offer a straightforward way to form chiral structures from achiral synthetic polymers.

Science & Technology - Other Topics↗

Ring-Polymer Molecular Dynamics Rate Coefficient Calculations for Insertion Reactions: X + H 2 → HX + H (X = N, O)

The thermal rate constants of two prototypical insertion-type reactions, namely, N/O + H 2 → NH/OH + H, are investigated with ring polymer molecular dynamics (RPMD) on full-dimensional potential energy surfaces using recently developed RPMDrate code. It is shown that the unique ability of the RPMD approach among the existing theoretical methods to capture the quantum effects, e.g., tunneling and zero-point energy, as well as recrossing dynamics quantum mechanically with ring-polymer trajectories leads to excellent agreement with rigorous quantum dynamics calculations. Lastly, the present result is encouraging for future applications of the RPMD method and the RPMDrate code to complex-forming chemical reactions involving polyatomic reactants.

insertion reaction↗

Poly-Amide Modified Copper Foam Electrodes for Enhanced Electrochemical Reduction of Carbon Dioxide

A strategy to modulate the electrocatalytic activity of copper toward CO 2 reduction involving adsorption of acrylamide, acrylic acid, and allylamine polymers is presented. Modification of electrodeposited copper foam with poly(acrylamide) leads to a significant enhancement in faradaic efficiency for ethylene from 13% (unmodified foam) to 26% at -0.96 V vs RHE, whereas methane yield is unaffected. Effects from crystalline phase distribution and copper oxide phases are ruled out as the source of enhancement through XPS and in situ XRD analysis. DFT calculations reveal that poly(acrylamide) adsorbs on the copper surface via the oxygen atom on the carbonyl groups and enhances ethylene formation by (i) charge donation to the copper surface that activates CO for dimerization, (ii) chemical stabilization of the CO dimer (a key intermediate for C 2 products) by hydrogen-bond interactions with the -NH 2 group, and (iii) facilitating the adsorption of CO molecules near the polymer, increasing local surface coverage. Poly(acrylamide) with copper acts as a multipoint binding catalytic system where the interplay between activation and stabilization of intermediates results in enhanced selectivity toward ethylene formation. Finally, modification with poly(acrylic acid) which has a similar structure to poly(acrylamide) also shows some enhancement in activity but is unstable, whereas poly(allylamine) completely suppresses CO 2 reduction in favor of the hydrogen evolution reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The Effects of Physicochemical Properties of Sludge on Dewaterability Under Chemical Conditioning with Amphoteric Polymer

This study investigated the effects of chemical conditioning with amphoteric terpolymer poly (acrylamide-’acryloyloxyethyl trimethyl ammonium chloride -2-acrylamido-2-methyl-propane sulfonate) (PADA) on sludge dewaterability. Particle size, fractal dimension, surface charge, extracellular polymeric substances (EPS) and trivalent metal ions (Al{sup 3+} and Fe{sup 3+}) of sludge were monitored and Pearson statistical analysis was used to understand the correlation of dewaterability and physicochemical properties of sludge. The results revealed that: (1) Sludge dewaterability was significantly enhanced by amphoteric polymer PADA. (2) Particle, fractal dimension and surface charge of sludge were associated with anionic degrees and molecular weights of polymer. (3) PADA had apparent effects on removal of EPS and enrichment of metal ions in sludge system. (4) Content of water and specific resistance to filtration had statistically strong correlations with the values of particle size, fractal dimension and EPS, but had weak correlations with values of surface charge and metal ions.

36 MATERIALS SCIENCE↗

Fabrication, thermal analysis, and heavy ion irradiation resistance of epoxy matrix nanocomposites loaded with silane-functionalized ceria nanoparticles

This paper describes a detailed understanding of how nanofillers function as radiation barriers within the polymer matrix, and how their effectiveness is impacted by factors such as composition, size, loading, surface chemistry, and dispersion. Here, we designed a comprehensive investigation of heavy ion irradiation resistance in epoxy matrix composites loaded with surface-modified ceria nanofillers, utilizing tandem computational and experimental methods to elucidate radiolytic damage processes and relate them to chemical and structural changes observed through thermal analysis, vibrational spectroscopy, and electron microscopy. A detailed mechanistic examination supported by FTIR spectroscopy data identified the bisphenol A moiety as a primary target for degradation reactions. Results of computational modeling by the Stopping Range of Ions in Matter (SRIM) Monte Carlo simulation were in good agreement with damage analysis from surface and cross-sectional SEM imaging. All metrics indicated that ceria nanofillers reduce the damage area in polymer nanocomposites, and that nanofiller loading and homogeneity of dispersion are key to effective damage prevention. The results of this study represent a significant pathway for engineered irradiation tolerance in a diverse array of polymer nanocomposite materials. Numerous areas of materials science can benefit from utilizing this facile and effective method to extend the reliability of polymer materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Hair treatment process providing dispersed colors by light diffraction

A hair treatment process for providing dispersed colors by light diffraction including (a) coating the hair with a material comprising a polymer, (b) pressing the hair with a pressing device including one or more surfaces, and (c) forming a secondary nanostructured surface pattern on the hair that is complementary to the primary nanostructured surface pattern on the one or more surfaces of the pressing device. The secondary nanostructured surface pattern diffracts light into dispersed colors that are visible on the hair. The section of the hair is pressed with the pressing device for from about 1 to 55 seconds. The polymer has a glass transition temperature from about 55.degree. C. to about 90.degree. C. The one or more surfaces include a primary nanostructured surface pattern.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Polymer Aerogels for Lunar Applications and Beyond

As the Space Community endeavors to reach new heights of exploration, materials for extreme environment are on the forefront of research. One such material would include polymer aerogels; lightweight solids with nano-scale pore size, high internal surface area, low thermal conductivity, and extremely high porosities. Due to these interesting properties, aerogels are ideal as thermal insulators but are by no means limited to this application. The high porosity and surface area also make aerogels an ideal host system for particle incorporation for applications such as catalyst supports, sensor platforms, and vibro-acoustic mitigating materials. Polymer aerogels also have the potential to combat issues found in extraterrestrial environments such as dust and radiation mitigation. Herein, current research will be discussed as it pertains to Space exploration.

Stephanie Vivod↗

Physical and chemical properties of some new perfluoropolyalkylether lubricants prepared by direct fluorination

A series of perfluoropolyalkylether (PFPAE) fluids was synthesized by direct fluorination. Viscosity-temperature properties, oxidation stabilities, oxidation-corrosion properties, bulk modulus, lubricity, surface tension and density were measured. It was shown that as the carbon to oxygen ratio in the polymer repeating unit decreases, the viscometric properties improve, the fluids may become poorer boundary lubricants, the bulk modulus increases, the surface tension increases and the fluid density increases. The presence of difluoromethylene oxide units in the polymer does not significantly lower the oxidation and oxidation-corrosion stabilities as long as the difluoromethylene oxide units are separated by other units.

Jones, W. R., Jr.↗

Formation and surface-stabilizing contributions to bare nanoemulsions created with negligible surface charge

The stabilization of nanoemulsions, nanosized oil droplets dispersed in water, is commonly achieved through the addition of surfactants and polymers. However, nanoemulsions in the absence of emulsifiers have been observed to acquire a significant negative charge at their surface, which ultimately contributes to their stability. While the source of this negative charge is disputed to this day, its presence is taken as an inherent property of the aqueous–hydrophobic interface. This report provides a look at the molecular structure and bonding characteristics of bare aqueous–hydrophobic nanoemulsion interfaces. We report the creation of bare nanoemulsions with near zero surface charge, which are marginally stable for several days. The process of creating these low-charge nanoemulsions (LCNEs) required rigorous cleaning procedures and proper solvent storage conditions. Using vibrational sum-frequency scattering spectroscopy, we measure the structure and bonding of the interfacial aqueous and hydrophobic phases. The surfaces of these LCNE samples possess a measurable free OH vibration, not found in previous studies and indicative of a clean interface. Tuning the nanoemulsion charge through addition of anionic surfactants, modeling potential surface-active contaminants, we observe the free OH to disappear and a reorientation of the interfacial hydrophobic molecules at micromolar surfactant concentrations. Notably, the free OH vibration provides evidence for stronger dispersion interactions between water molecules and the hydrophobic phase at the LCNE surface compared with similar planar water–alkane interfaces. We propose the stronger bonding interactions, in addition to an ordered interfacial aqueous layer, contribute to the delayed droplet coalescence and subsequent phase separation.

59 BASIC BIOLOGICAL SCIENCES↗

Engineering Polymers as Structural Materials in Spacecraft Water Systems

The novel application of structural materials, surface treatments, and barrier coatings is desired to mitigate the rapid loss of ionic silver (Ag+) biocide observed with passive metal alloys, improve reliability, and reduce system mass. In this work, we provide an initial look at the potential replacement of these heritage alloys in spacecraft water systems with high-performance thermoplastic engineering polymers, including PEEK, PEI, and PVDF. Such materials have found increasing use as structural materials in a broad array of performance-critical applications, including in the aerospace, medical implant, and chemical processing fields. We selected a number of promising materials for investigation, compiled mechanical behavior data, and conducted theoretical performance analyses. We also identified and began to address numerous material suitability concerns as well as design requirements for pressurized components in human-rated spacecraft hardware. These include material flammability, offgassing, leaching, chemical resistance, radiation tolerance, prevention of fracture/yielding, and others. We find that there is significant potential for use of engineering polymers in spacecraft water systems, and suggest some directions for future research.

Lance Dean Delzeit↗

Reversibly growing crosslinked polymers with programmable sizes and properties

Growth constitutes a powerful method to post-modulate materials’ structures and functions without compromising their mechanical performance for sustainable use, but the process is irreversible. To address this issue, we here report a growing-degrowing strategy that enables thermosetting materials to either absorb or release components for continuously changing their sizes, shapes, compositions, and a set of properties simultaneously. The strategy is based on the monomer-polymer equilibrium of networks in which supplying or removing small polymerizable components would drive the networks toward expansion or contraction. Using acid-catalyzed equilibration of siloxane as an example, we demonstrate that the size and mechanical properties of the resulting silicone materials can be significantly or finely tuned in both directions of growth and decomposition. The equilibration can be turned off to yield stable products or reactivated again. During the degrowing-growing circle, material structures are selectively varied either uniformly or heterogeneously, by the availability of fillers. Our strategy endows the materials with many appealing capabilities including environment adaptivity, self-healing, and switchability of surface morphologies, shapes, and optical properties. Since monomer-polymer equilibration exists in many polymers, we envision the expansion of the presented strategy to various systems for many applications.

36 MATERIALS SCIENCE↗

Fabrication of Piezoelectric Polymer and Metal–Organic Framework Composite Thin Films Using Solution Shearing

Polymer-metal–organic framework (polymer-MOF) composites have garnered significant interest as polymers can enhance the processability and industrial applicability of MOFs. Thin films of these composites are particularly attractive for applications in sensing, separations, and flexible electronics. Solution shearing, a meniscus-guided coating technique, has emerged as a scalable process for fabricating thin films of MOFs, and can produce large-area films within minutes. In this study, we utilized solution shearing to fabricate composite thin films of a MOF UiO-66 and a piezoelectric polymer poly(vinylidene fluoride-trifluoroethylene) (P(VDF-TrFE)), investigating how polymer concentration during MOF synthesis and composite formation influences thin film properties, including crystallinity, surface coverage, and piezoelectric performance. Additionally, solid-state NMR spectroscopy was utilized to probe the interactions between P(VDF-TrFE) and UiO-66 in the composite. Evidence from solid-state NMR indicated polymer-MOF interactions, suggesting that the polymer strands are in close proximity to the UiO-66 pores, supporting a mixed surface coating and pore infiltration model. Furthermore, incorporating P(VDF-TrFE) enhanced the film’s areal coverage from 70% to 100%. While the thermal conductivity remained essentially unchanged, the composite film showed an improved piezoelectric effect. The composite with 91 wt % P(VDF-TrFE) exhibited the highest output voltage of 9.1 V and a sensitivity of 0.26 V/N under applied pressure. This work demonstrates the potential of solution shearing as a scalable technique for fabricating polymer-MOF composite thin films.

P(VDF-TrFE)↗

Increase in the effective viscosity of polyethylene under extreme nanoconfinement

Understanding polymer transport in nanopores is crucial for optimizing heterogeneously catalyzed processes in polymer upcycling and fabricating high-performance nanocomposite films and membranes. Although confined polymer dynamics have been extensively studied, the behavior of polyethylene (PE)—the most widely used commodity polymer—in pores smaller than 20 nm remains largely unexplored. We investigate the effects of extreme nanoconfinement on PE transport using capillary rise infiltration in silica nanoparticle packings with average pore radii ranging from ~1 to ~9 nm. Using in situ ellipsometry and the Lucas–Washburn model, we discover a previously unknown inverse relationship between effective viscosity (η eff ) and average pore radius (R pore ). Additonally, we determine that PE transport under these extreme conditions is primarily governed by physical confinement, rather than pore surface chemistry. We refine an existing theory to provide a generalized formalism to describe the polymer transport dynamics over a wide range of pore radii (from 1 nm and larger). Our results offer valuable insights for optimizing catalyst supports in polymer upcycling and improving infiltration processes for nanocomposite fabrication.

36 MATERIALS SCIENCE↗

Reticulated Nanoporous Polymers by Controlled Polymerization-Induced Microphase Separation

Materials with percolating mesopores are attractive for applications such as catalysis, nanotemplating, and separations. Polymeric frameworks are particularly appealing because the chemical composition and the surface chemistry are readily tunable. We report on the preparation of robust nanoporous polymers with percolating pores in the 4- to 8-nanometer range from a microphase-separated bicontinuous precursor. We combined polymerization-induced phase separation with in situ block polymer formation from a mixture of multifunctional monomers and a chemically etchable polymer containing a terminal chain transfer agent. This marriage results in microphase separation of the mixture into continuous domains of the etchable polymer and the emergent cross-linked polymer. Precise control over pore size distribution and mechanical integrity renders these materials particularly suited for various advanced applications.

36 MATERIALS SCIENCE↗

Innovative Electrostatic Adhesion Technologies

Developing specialized Electro-Static grippers (commercially used in Semiconductor Manufacturing and in package handling) will allow gentle and secure Capture, Soft Docking, and Handling of a wide variety of materials and shapes (such as upper-stages, satellites, arrays, and possibly asteroids) without requiring physical features or cavities for a pincher or probe or using harpoons or nets. Combined with new rigid boom mechanisms or small agile chaser vehicles, flexible, high speed Electro-Static Grippers can enable compliant capture of spinning objects starting from a safe stand-off distance. Electroadhesion (EA) can enable lightweight, ultra-low-power, compliant attachment in space by using an electrostatic force to adhere similar and dissimilar surfaces. A typical EA enabled device is composed of compliant space-rated materials, such as copper-clad polyimide encapsulated by polymers. Attachment is induced by strong electrostatic forces between any substrate material, such as an exterior satellite panel and a compliant EA gripper pad surface. When alternate positive and negative charges are induced in adjacent planar electrodes in an EA surface, the electric fields set up opposite charges on the substrate and cause an electrostatic adhesion between the electrodes and the induced charges on the substrate. Since the electrodes and the polymer are compliant and can conform to uneven or rough surfaces, the electrodes can remain intimately close to the entire surface, enabling high clamping pressures. Clamping pressures of more than 3 N/cm2 in shear can be achieved on a variety of substrates with ultra-low holding power consumption (measured values are less than 20 microW/Newton weight held). A single EA surface geometry can be used to clamp both dielectric and conductive substrates, with slightly different physical mechanisms. Furthermore EA clamping requires no normal force be placed on the substrate, as conventional docking requires. Internally funded research and development has demonstrated that EA can function effectively in space, even in the presence of strong ultraviolet radiation, atomic oxygen, and free electrons. We created a test setup in an existing vacuum chamber to simulate low-Earth-orbit conditions. An EA mechanism was fabricated and installed in the chamber, instrumented, operated in a vacuum, and subjected to ultraviolet photons and free electrons generated by an in-chamber multipactor electron emitter. Extensions to EA that can add value include proximity and contact sensing and transverse motion or rotation, both of which could enhance docking or assembly applications. Possible next steps include development of targeted applications for ground investigation or on-orbit subsystem performance demonstrations using low cost access to space such as CubeSats.

Bryan, Tom↗

Lectin-functionalized poly(glycidyl methacrylate)-block-poly(vinyldimethyl azlactone) surface supports for high avidity microbial capture

Microbial exopolysaccharides (EPS) play a critical and dynamic role in shaping the interactions between microbial community members and their local environment. The capture of targeted microbes using surface immobilized lectins that recognize specific extracellular oligosaccharide moieties offers a non-destructive method for functional characterization based on EPS content. In this report, we evaluate the use of the block co-polymer, poly(glycidyl methacrylate)-block-4,4-dimethyl-2-vinylazlactone (PGMA-b-PVDMA), as a surface support for lectin-specific microbial capture. Arrays of circular polymer supports ten micron in diameter were generated on silicon substrates to provide discrete, covalent coupling sites for Triticum vulgare and Lens culinaris lectins. These supports promoted microbe adhesion and colony formation in a lectin-specific manner. Silicon posts with similar topography containing only physisorbed lectins showed significantly less activity. These results demonstrate that micropatterned PGMA-b-PVDMA supports provide a unique platform for microbial capture and screening based on EPS content by combining high avidity lectin surfaces with three-dimensional topography.

block co-polymers↗