Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STRESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

EXPERIMENTAL-BASED DISCUSSION FOR THE SEPARATION OF RESIDUAL STRESSES AND COLD WORK IN SHOT PEENED IN718 USING HIGH FREQUENCY EDDY CURRENT SPECTROSCOPY

Typical aero engine alloys, such as IN718, can be surface-treated by shot peening to induce near-surface compressive strains. To calculate the remaining operation time for those critical aero engine components, a quantitative nondestructive determination of near-surface strain gradients has to be developed. We have demonstrated in the past, that it is possible to obtain a characteristic depth profile (surface and sub-surface) of the electrical conductivity of shot peened specimen by using high-frequency eddy current techniques. The measured conductivity profile is resulting from residual stresses, cold work, surface roughness, and the microstructure of the material. The objective is to measure residual stresses (separately from other material properties) in such components after a defined life time. It can be assumed, that surface roughness and microstructure remain unchanged in IN718 materials over their lifetime, but cold work and residual stresses can change independently. Consequently, there is a need to clearly separate the information from both material properties of received eddy current conductivity signals in order to obtain specific information related to residual stresses. This paper presents results acquired from different experiments, conducted to separate both effects by using the eddy current technique on shot peened IN718 materials. We present different physical approaches and illustrate the experiments to solve them. In addition, we will demonstrate that there is a need to use additional techniques, for example ultrasonic time-of-flight measurements, to separate the effects of residual stresses from compound (mixed) signals obtained on cold work samples.

36 MATERIALS SCIENCE↗

Residual stress-dependent electric conductivity of sputtered co-doped CeO{sub 2} thin-film electrolyte

Sm{sup 3+} and Nd{sup 3+} co-doped ceria thin-film electrolytes have been deposited on polycrystalline alumina substrates via RF magnetron sputtering. Electric conductivity is evaluated with respect to the residual stress in the film by sin{sup 2} {psi}-methodology, indicating that an in-plane tensile stress is applied to the as-deposited film. The stress in the film increases as annealing temperature decreases, and there is an enlarged crystal lattice. The results also reveal that the annealed film with a greater stress shows a higher electric conductivity, which might be due to the lower activation energy. The conductivity of the film annealed at 600 deg. C is as high as 0.009 S cm{sup -1} at 500 deg. C, and the residual stress is determined to be 542.70 MPa at room temperature.

36 MATERIALS SCIENCE↗

Characterization Of Flow Stress Of Different AA6082 Alloys By Means Of Hot Torsion Test

FEM simulations are become the most powerful tools in order to optimize the different aspects of the extrusion process and an accurate flow stress definition of the alloy is a prerequisite for a reliable effectiveness of the simulation. In the paper the determination of flow stress by means of hot torsion test is initially presented and discussed: the several approximations that are usually introduced in flow stress computation are described and computed for an AA6082 alloy in order to evidence the final effect on curves shapes. The procedure for regressing the parameters of the sinhyperbolic flow stress definition is described in detailed and applied to the described results. Then four different alloys, extracted by different casting batches but all namely belonging to the 6082 class, were hot torsion tested in comparable levels of temperature and strain rate up to specimen failure. The results are analyzed and discussed in order to understand if a mean flow stress behavior can be identified for the whole material class at the different tested conditions or if specific testing conditions (chemical composition of the alloy, specimen shape, etc) influence the materials properties to a higher degree.

36 MATERIALS SCIENCE↗

Residual Stresses in DC cast Aluminum Billet: Neutron Diffraction Measurements and Thermomechanical Modeling

Thermally-induced residual stresses, generated during the industrial Direct Chill casting process of aluminum alloys, can cause both significant safety concerns as well as the formation of defects during down-stream processing. Although these thermally induced strains can be partially relieved by permanent deformation, cracks will be generated either during solidification (hot tears) or post-solidification cooling (cold cracks) when stresses exceed the deformation limit of the alloy. Furthermore, the thermally induced strains result in the presence of large internal stresses within the billet before further processing steps. Although numerical models have been previously developed to compute these residual stresses, most of the computations have been validated only against measured surface distortions. In the present work, the variation in residual elastic strains and stresses in the steady state regime of casting has been measured as a function of radial position using neutron diffraction in an AA6063 grain-refined cylindrical billet. These measurements have been carried out on the same billet section at Poldi at PSI-Villigen and at Salsa at ILL-Grenoble and compare favorably. The results are used to validate a thermo-mechanical finite element casting model and to assess the level of stored elastic energy within the billet.

36 MATERIALS SCIENCE↗

Interdiffusion and stress development in single-crystalline Pd/Ag bilayers

Interdiffusion and stress evolution in single-crystalline Pd/single-crystalline Ag thin films were investigated by Auger electron spectroscopy sputter-depth profiling and in-situ X-ray diffraction, respectively. The concentration-dependent chemical diffusion coefficient, as well as the impurity diffusion coefficient of Ag in Pd could be determined in the low temperature range of 356 °C–455 °C. As a consequence of the similarity of the strong concentration-dependences of the intrinsic diffusion coefficients, the chemical diffusion coefficient varies only over three orders of magnitude over the whole composition range, despite the large difference of six orders of magnitude of the self-diffusion coefficients of Ag in Ag and Pd in Pd. It is shown that the Darken-Manning treatment should be adopted for interpretation of the experimental data; the Nernst-Planck treatment yielded physically unreasonable results. Apart from the development of compressive thermal stress, the development of stress in both sublayers separately could be ascribed to compositional stress (tensile in the Ag sublayer and compressive in the Pd sublayer) and dominant relaxation processes, especially in the Ag sublayer. The effect of these internal stresses on the values determined for the diffusion coefficients is shown to be negligible.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Measurement of Residual Stresses by X-ray Diffraction Near Simulated Heat Affected Zones in Austenitic Stainless Steels

Simulated heat-affected zones (HAZs) were made in austenitic stainless steel specimens using a Gleeble. The samples were heated to temperatures as high as 1100°C by computer controlled resistance heating. By controlling the heating rate, maximum temperature, and cooling rate, a wide range of residual stresses were introduced in the specimens. Stress measurements were made using X-ray diffraction. It was found that significant stress gradients were produced in the simulated HAZs, and that all stresses were compressive in nature, both in the longitudinal and transverse directions. These results are not representative of the residual stresses determined in the HAZs of real welds, thus calling into question some aspects of the role of the Gleeble in such simulations.

36 MATERIALS SCIENCE↗

Final Report: Characterization of Canister Mockup Weld Residual Stresses

Stress corrosion cracking (SCC) of interim storage containers has been indicated as a high priority data gap by the Department of Energy (DOE) (Hanson et al., 2012), the Electric Power Research Institute (EPRI, 2011), the Nuclear Waste Technical Review Board (NWTRB, 2010a), and the Nuclear Regulatory Commission (NRC, 2012a, 2012b). Uncertainties exist in terms of the environmental conditions that prevail on the surface of the storage containers, the stress state within the container walls associated both with weldments as well as within the base metal itself, and the electrochemical properties of the storage containers themselves. The goal of the work described in this document is to determine the stress states that exists at various locations within a typical storage canister by evaluating the properties of a full-diameter cylindrical mockup of an interim storage canister. This mockup has been produced using the same manufacturing procedures as the majority of the fielded spent nuclear fuel interim storage canisters. This document describes the design and procurement of the mockup and the characterization of the stress state associated with various portions of the container. It also describes the cutting of the mockup into sections for further analyses, and a discussion of the potential impact of the results from the stress characterization effort.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of Combined and Sequential Accelerated Stress Testing for Derisking Photovoltaic Modules

This talk reviews sequential and combined accelerated stress tests of the past decade that have been shown to better replicate degradation mechanisms seen in the field, that single-factor steady-state tests have failed to reproduce. When designing stress tests for PV modules, it is shown, with examples, how it is beneficial to consider representation of the shipping module, the stress factors applied, and how the stress factors are sequenced or combined in the natural environment. Finally, current and future efforts to realize accelerated stress tests based on these concepts are discussed.

14 SOLAR ENERGY↗

Estimating the Penetration Depth and Orientation of Stress Corrosion Cracks Using Time-Reversal Acoustics

Austenitic stainless steels are known to be susceptible to stress corrosion cracking (SCC), which is an aggressive type of corrosion that exists when a material under tensile stress is placed in a corrosive environment. This is of particular concern as the processing (i.e., cold rolling) and construction (welding) of storage canisters produce an inherent residual stress in metals that can lead to SCC. In this context, our objective is to study the formation of stress corrosion cracks within Type 304L stainless steel, which is frequently used in containers for used nuclear fuel disposal. The conditions present in storage canisters (i.e., elevated temperatures, high residual stresses near welds, and exposure to humidity and chloride) make them susceptible to SCC, potentially leading to critical through-wall failure, and thus loss of containment. The timescales on which through-wall failure is expected in a storage canister under typical conditions is on the order of tens of years. While through-wall flaws are catastrophic (e.g., release of helium and fission gases), the long timescales allow for routine inspection, and potentially mitigation, providing methods exist. This paper is focused on the former problem, i.e. detection of SCC, and the development of a tool for inspection of storage canisters. We will discuss the recent work we did on detecting the presence of SCC as well as imaging on its orientation and penetration depth using an acoustic technique developed at Los Alamos National Laboratory (LANL). This technique has been applied successfully in the laboratory on stainless steel samples with SCC provided by General Electric (GE) and the Electric Power Research Institute (EPRI). Recently, we have also demonstrated that this technique can be deployed for field inspections in tight and confined spaces. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

INTERFACE RESIDUAL STRESSES IN DENTAL ZIRCONIA USING LAUE MICRO-DIFFRACTION

Due to their aesthetic value and high compressive strength, dentists have recently employed ceramics for restoration materials. Among the ceramic materials, zirconia provides high toughness and crack resistant characteristics. Residual stresses develop in processing due to factors including grain anisotropy and thermal coefficient mismatch. In the present study, polychromatic X-ray (Laue) micro-diffraction provided grain orientation and residual stresses on a clinically relevant zirconia model ceramic disk. A 0.5 mm x 0.024 mm region on zirconia was examined on a 500 nm scale for residual stresses using a focused poly-chromatic synchrotron X-ray beam. Large stresses ranging from - to + 1GPa were observed at some grains. On average, the method suggests a relatively small compressive stress at the surface between 47 and 75 MPa depending on direction.

36 MATERIALS SCIENCE↗

Operational Efficiency Evaluation of a Setup for Removing Stresses in the Steam Header of PGV-1000 Steam Generator

The effectiveness of a setup for removing stresses in the steam header of a PGV-1000 steam generator is evaluated. The evaluation is based on an investigation of the stress state by means of magnetic anisotropy measurements performed in the zone of the No. 111 weld seam of the hot header of steam generators operating in one of the power-generating units with a V-320 series reactor arrangement. Inspections made it possible to obtain cartograms of the distribution of the difference of the principal mechanical stresses along the perimeter of the weld connection of a PGV-1000 header equipped with a cooling mantle and headers without such a mantle. By means of statistical analysis of the data, a diagram of the distribution of the principal mechanical stresses was obtained. In addition, the distribution of the standard deviation of the principal mechanical stresses as a measure of the dispersion of a random quantity relative to its mathematical expectation was determined.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

First-Principles and Thermodynamic Simulation of Elastiс Stress Effect on Energy of Hydrogen Dissolution in Alpha Iron

Mobile hydrogen, when dissolving in metals, redistributes due to the density gradients and elastic stresses, and enables destruction processes or phase transformations in local volumes of a solvent metal. It is rather important in solid state physics to investigate these interactions. The first-principle calculations performed in terms of the density functional theory, are used for thermodynamic simulation of the elastic stress effect on the energy of hydrogen dissolution in α-Fe crystal lattice. The paper presents investigations of the total energy of Fe–H system depending on the lattice parameter. As a result, the relation is obtained between the hydrogen dissolution energy and stress. A good agreement is shown between the existing data and simulation results. The extended equation is suggested for the chemical potential of hydrogen atom in iron within the local stress field. Two parameters affecting the hydrogen distribution are compared, namely local stress and phase transformations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Investigation of Stress Field and Fracture Development During Shale Maturation Using Analog Rock Systems

The emergence of hydrocarbons within shale as a major recoverable resource has sparked interest in fluid transport through these tight mudstones. Recent studies suggest the importance to recovery of microfracture networks that connect localized zones with large organic content to the inorganic matrix. This paper presents a joint modeling and experimental study to examine the onset, formation, and evolution of microfracture networks as shale matures. Both the stress field and fractures are simulated and imaged. A novel laboratory-scale, phase-field fracture propagation model was developed to characterize the material failure mechanisms that play a significant role during the shale maturation process. The numerical model developed consists of coupled solid deformation, pore pressure, and fracture propagation mechanisms. Benchmark tests were conducted to validate model accuracy. Laboratory-grade gelatins with varying Young’s modulus were used as scaled-rock analogs in two dimensional Hele-Shaw cell apparatus. Yeast within the gelatin generates gas in a fashion analogous to hydrocarbon formation as shale matures. These setups allow study and visualization of host rock elastic-brittle fracture and fracture network propagation mechanisms. The experimental setup was fitted to utilize photoelasticity principles coupled with birefringence properties of gelatin to explore visually the stress field of the gelatin as the fracture network developed. Stress optics image analysis and Linear Elastic Fracture Mechanics (LEFM) principles for crack propagation were used to monitor fracture growth for each gelatin type. Observed and simulated responses suggest gas diffusion within and deformation of the gelatin matrix as predominant mechanisms for energy dissipation depending on gelatin strength. LEFM, an experimental estimation of principal stress development with fracture growth, at different stages was determined for each gelatin rheology. Here, the interplay of gas diffusion and material deformation determines the resulting frequency and pattern of fractures. Results correlate with Young’s modulus. Experimental and computed stress fields reveal that fractures resulting from internal gas generation are similar to, but not identical to, type 1 opening mode.

58 GEOSCIENCES↗

Long-term sinking of nuclear waste canisters in salt formations by low-stress creep at high temperature

Abstract Rock salt has a self-sealing capacity, low permeability, and high thermal conductivity, making it a potential host for heat-generating nuclear waste. The feasibility of nuclear waste disposal within salt formations has been investigated mostly for small-sized canisters. Geologic disposal of larger-sized canisters originally designed for spent fuel storage and transportation has lately been examined as a cost-effective alternative. This raises questions about their long-term vertical movement due to their weight and high decay heat. Low-stress creep governs this movement; however, most salt constitutive models do not incorporate it. In this paper, the Norton and the WIPP creep models are compared with the Lux/Wolters/Lerche (LWL) model and a simpler model that combines linear and Norton creep laws (named combined creep model). The LWL and combined creep models consider pressure solution creep, though all incorporate dislocation creep. The models are first applied to creep tests under various stress levels. The LWL and the combined creep models results fit the experimental data well in both high and low stress ranges, whereas the Norton and WIPP models results only fit in higher-stress ranges. The different models are further applied for analyzing long-term canister movement. A sinking rate of $$-4.4\times 10^{-7}$$ - 4.4 × 10 - 7 mm/year was predicted using the Norton and WIPP models versus $$-2.1\times 10^{-2}$$ - 2.1 × 10 - 2 mm/year and $$-3.1\times 10^{-2}$$ - 3.1 × 10 - 2 mm/year using the LWL and the combined creep models, respectively. This comparative study confirms that creep models calibrated exclusively against high-deviatoric stress data might result in an inaccurate estimation of waste packages sinking rate in salt formations.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Retardation of Small Creep–Fatigue Crack in Gr. 91 Steel Through the Combined Effects of Stress Relaxation, Microstructural Evolution, and Oxidation

This investigation reports an unusual effect of hold time (up to 10 seconds) on retardation in the growth of creep–fatigue small cracks at 550 °C in Grade 91 steel. The observed phenomenon was interpreted by elucidating multiple processes that are active in the plastic zone at the crack tip. To this effect, microstructural and mechanical responses of the crack tip plastic zone were compared with the mechanical and microstructural responses during low cycle fatigue/creep–fatigue. It is proposed that the stress relaxation that occurs during the hold time can reduce the stress intensity in the plastic zone of crack tip thus, contributing to retardation in the small crack growth rate. Aside from stress relaxation, stress intensity in the crack tip can be further reduced by the phenomenon of cyclic softening that occurs because of plasticity-induced microstructural coarsening. Separately, the contribution of oxidation-induced crack tip shielding is also considered to explain the observed effects of hold time on crack growth rates. Taken together, a combination of stress relaxation, enhanced rate of cyclic softening, and higher degree of oxidation with the introduction of a hold time is demonstrated to be responsible for reduction in the crack growth under creep–fatigue conditions.

36 MATERIALS SCIENCE↗

Residual Stresses in Explosively Welded Plates Made of Titanium Grade 12 and Steel with Interlayer

Distributions of residual stress components in explosively welded three-layer plate composed of titanium Grade 12, titanium Grade 1 and SA516 Grade 70 steel are investigated in this paper. The study applied the sectioning and the hole-drilling strain gage methods for residual stress measurement. The results have shown an inhomogeneous residual stress distribution, approximated by fourth-order polynomial along the thickness of a three-layer plate. Biaxial compressive residual stress state is observed in titanium Grade 12 and Grade 1 layers which change to tensile type in the vicinity of the interface between titanium Grade 1 and steel. Microstructure observation reveals the presence of the adiabatic shear bands in titanium Grade 12 layer at the interface with titanium Grade 1 interlayer. The observed distribution of residual stress components is justified by the occurrence of the shock wave phenomena.

36 MATERIALS SCIENCE↗

A Simplified Procedure to Determine Post-necking True Stress–Strain Curve from Uniaxial Tensile Test of Round Metallic Specimen Using DIC

Triaxial state of stress is usually generated in the necked zone because of neck geometry, and as a consequence proper correction of true tensile stress–strain curve after necking is mandatory. Various correction factors like Bridgman, Davidenkov and Spiridonova, Siebel and Schwaigere are available in the published literature to calculate true stress from mean axial stress. Similarly true strains can be calculated from the minimum diameters of the round specimen in the necked region for various true stress levels. But experimental determination of correction factors and minimum diameters of the round specimen in the necked region is a cumbersome task. This investigation shows a simplified procedure to determine true strains and the correction factors from digital image correlation-based local strain measurement in the necked region. The present procedure is validated by experimental results of rail steel.

36 MATERIALS SCIENCE↗

Numerical Simulation of Residual Stresses in Multipass Gas Metal Arc-Welded Joints of Thick Aluminum Alloy Plates

Numerical simulation was utilized to investigate the residual stresses in the multipass gas metal arc-welded joints of high-strength Al-Zn-Mg alloy plates. In order to elevate the reliability of numerical simulation, the heat source model, parameters characterizing the thermal and mechanical properties, boundary conditions, material constitutive model and finite element meshing were discussed in detail. As a novelty of this paper, the modified Arrhenius constitutive equation of the base material and the filled material was obtained according to the results of high-temperature tensile tests. Distributions of stress on the upper and bottom surface of the joint were obtained based on numerical simulation. Special attention was paid to the evolutions of local residual stress on the bottom surface of the joint, and it’s found that residual stresses on the bottom surface of the joint were almost unchanged after the weld seam approached a certain thickness. Blind-hole method and x-ray method were adopted to detect the residual stresses on the surfaces to verify the accuracy of the results obtained by numerical simulation.

36 MATERIALS SCIENCE↗