Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SAND”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

Characterization of a 12-pdr wrought-iron cannonball from the Akko 1 shipwreck

The Akko 1 shipwreck, discovered in Akko harbor, Israel, is the remains of an eastern Mediterranean brig built at the beginning of the 19th century. Among other finds, eleven cannonballs were found in the shipwreck and three of them were retrieved. Two of the cannonballs, the 9- and 24-pdrs, have been studied previously. The present study of the 12-pdr cannonball included γ-rays radiographic testing, XRF analysis, density measurements, optical microscopy and SEM-EDS observation, OES analysis and microhardness tests. The investigation included characterization of the composition, microstructure and slag analysis. The results revealed a quite homogenous microstructure of α-ferrite phase, with glassy, wüstite and fayalite slags, as typical for a wrought-iron—annealed product, a more complicated and an earlier technology, compared to the 9- and 24-pdr that were made of cast-iron. Ferritic cannonballs are extremely rare, especially in the 19th century, when cannonballs were manufactured of cast iron by the sand casting process. The different manufacturing methods may indicate a different place of fabrication, and an apparently earlier production date for the 12-pdr, which might have even been used as ballast. - Highlights: • Three cannonballs were retrieved from the 19th century Akko 1 shipwreck. • The 12-pdr differs from the 9- and 24-pdr cannonballs previously studied. • The 12-pdr was made of high quality annealed wrought-iron, not of cast-iron. • The technology used indicates a date earlier than the middle of the 19th century. • Perhaps the 12-pdr belonged to another navy than the other two or used as ballast.

36 MATERIALS SCIENCE↗

Replication of engine block cylinder bridge microstructure and mechanical properties with lab scale 319 Al alloy billet castings

In recent years, aluminum alloy gasoline engine blocks have in large part successfully replaced nodular cast iron engine blocks, resulting in improved vehicle fuel efficiency. However, because of the inadequate wear resistance properties of hypoeutectic Al–Si alloys, gray iron cylinder liners are required. These liners cause the development of large tensile residual stress along the cylinder bores and necessitate the maximization of mechanical properties in this region to prevent premature engine failure. The aim of this study was to replicate the engine cylinder bridge microstructure and mechanical properties following TSR treatment (which removes the sand binder to enable easy casting retrieval) using lab scale billet castings of the same alloy composition with varying cooling rates. Comparisons in microstructure between the engine block and the billet castings were carried out using optical and scanning electron microscopy, while mechanical properties were assessed using tensile testing. The results suggest that the microstructure at the top and middle of the engine block cylinder bridge was successfully replicated by the billet castings. However, the microstructure at the bottom of the cylinder was not completely replicated due to variations in secondary phase morphology and distribution. The successful replication of engine block microstructure will enable the future optimization of heat treatment parameters. - Highlights: • A method to replicate engine block microstructure was developed. • Billet castings will allow cost effective optimization of heat treatment process. • The replication of microstructure in the cylinder region was mostly successful. • Porosity was more clustered in the billet castings compared to the engine block. • Mechanical properties were lower in billet castings due to porosity and inclusions.

36 MATERIALS SCIENCE↗

Effects of Mo on microstructure of as-cast 28 wt.% Cr–2.6 wt.% C–(0–10) wt.% Mo irons

Microstructures of as-cast 28 wt.% Cr–2.6 wt.% C irons containing (0–10) wt.% Mo with the Cr/C ratio of about 10 were studied and related to hardness. The experimental irons were cast into dry sand molds. Microstructural investigation was performed by light microscopy, X-ray diffractometry, scanning electron microscopy, transmission electron microscopy and energy-dispersive X-ray spectrometry. It was found that the iron with about 10 wt.% Mo was eutectic/peritectic, whereas the others with less Mo content were hypoeutectic. The matrix in all irons was austenite, partly transformed to martensite during cooling. Mo addition promoted the formation of M{sub 23}C{sub 6} and M{sub 6}C. At 1 wt.% Mo, multiple eutectic carbides including M{sub 7}C{sub 3}, M{sub 23}C{sub 6} and M{sub 6}C were observed. M{sub 23}C{sub 6} existed as a transition zone between eutectic M{sub 7}C{sub 3} and M{sub 6}C, indicating a carbide transition as M{sub 7}C{sub 3}(M{sub 2.3}C) → M{sub 23}C{sub 6}(M{sub 3.8}C) → M{sub 6}C. At 6 wt.% Mo, multiple eutectic carbides including M{sub 7}C{sub 3} and M{sub 23}C{sub 6} were observed together with fine cellular/lamellar M{sub 6}C aggregates. In the iron with 10 wt.% Mo, only eutectic/peritectic M{sub 23}C{sub 6} and M{sub 6}C were found without M{sub 7}C{sub 3}. Mo distribution to all carbides has been determined to be increased from ca. 0.4 to 0.7 in mass fraction as the Mo content in the irons was increased. On the other hand, Cr distribution to all carbides is quite constant as ca. 0.6 in mass fraction. Mo addition increased Vickers macro-hardness of the irons from 495 up to 674 HV{sub 30}. High Mo content as solid-solution in the matrix and the formation of M{sub 6}C or M{sub 23}C{sub 6} aggregates were the main reasons for hardness increase, indicating potentially improved wear performance of the irons with Mo addition. - Highlights: • Mo promoted the formation of M{sub 23}C{sub 6} and M{sub 6}C in the irons with Cr/C ratio of about 10. • M{sub 23}C{sub 6} has higher Fe/Cr and Mo/Cr atm% ratios than M{sub 7}C{sub 3}. • Si content and high Mo content over about 9 atm% are characteristics of M{sub 6}C. • No M{sub 7}C{sub 3} was found at 10 wt.% Mo addition, only M{sub 23}C{sub 6} and M{sub 6}C presented. • High Mo matrices and M{sub 23}C{sub 6}/M{sub 6}C aggregates increased iron macro-hardness.

36 MATERIALS SCIENCE↗

Effects of Si on microstructure and phase transformation at elevated temperatures in ferritic white cast irons

The effects of Si on microstructure and phase transformation at elevated temperature of ferritic 31wt.%Cr-1.1wt.%C white cast irons with up to 3wt.%Si have been studied. Applications of these irons include parts requiring heat resistance at elevated temperature. The irons were produced by sand casting. The microstructure in as-cast condition and after being subjected to high temperature (700 to 1000 °C) was investigated by light microscopy, X-ray diffraction, and electron microscopy. The results revealed that the as-cast microstructure consisted mainly of primary ferrite dendrites and eutectic (ferrite + M{sub 7}C{sub 3}). Si promotes M{sub 7}C{sub 3}-to-M{sub 23}C{sub 6} transformation in the irons subjected to transformation at elevated temperature, but no sigma phase was found. The extent of M{sub 7}C{sub 3}-to-M{sub 23}C{sub 6} transformation increases proportional to the increasing transformation temperature, holding time and Si content in the irons. For the iron with 1.0wt.%Si content after holding at elevated temperatures, martensite was also found, which could be attributed to carbon accretion effects in eutectic ferrite. Si was incorporated in M{sub 23}C{sub 6} such that M{sub 23}C{sub 6} containing Si can show darker contrast under SEM-BEI as compared to M{sub 7}C{sub 3}; this is the opposite to what has been observed for the cases of typical M{sub 23}C{sub 6} and M{sub 23}C{sub 6} containing Mo or W. The results obtained are important to understand the change in properties of ferritic, high chromium irons containing Si subjected to elevated temperature.

36 MATERIALS SCIENCE↗

In-situ investigation of incipient melting in a 319 type Al alloy using laser scanning confocal microscopy

Highlights: • In-situ analysis of incipient melting of ternary eutectic in Al alloy. • Incipient melting occurred in three distinct stages in the eutectic. • Increased heating rate increase rate of liquid film propagation. • Incipient melting transformed initial eutectic structure and caused oxidation. • Study determined incipient melting mechanism for eutectic structures. - Abstract: The modified 319 Al alloy system has been used extensively in precision sand casting of automotive powertrain applications such as engine blocks and cylinder heads, with significant improvement in vehicle fuel efficiency. However, a concern in elevated temperature processing of Al alloys, such as heat treatment and hot working processes, is incipient melting of secondary phases, which is deleterious to mechanical properties. In this study, the laser scanning confocal microscopy (LSCM) technique was used in the analysis of in-situ changes in microstructure as a result of incipient melting. Microstructural analysis was carried out prior to and following elevated temperature exposure in the LSCM using optical microscopy, SEM and EDX. The results suggest that incipient melting of the Al-Al{sub 2}Cu-Al{sub 5}Mg{sub 8}Cu{sub 2}Si{sub 6} ternary eutectic clusters was initiated by the formation of a liquid film which propagated rapidly from the eutectic clusters, coating the Al dendrites in regions adjacent to the eutectic clusters. Following film formation, the ternary eutectic clusters melted completely. Incipient melting also resulted in a localized change in composition in the interdendritic channels as supported by a change in cluster morphology from eutectic to a combination of coarse blocky Al-Cu-Ni and Si particles, and ultra-fine eutectic.

36 MATERIALS SCIENCE↗

Non-destructive compositional and microstructural characterization of Sardinian Bronze Age swords through Neutron Diffraction

Highlights: • Determination of the manufacturing technique of some “Sa Idda” swords • New data on their provenience • Determination of: alloy composition, dendritic segregation, mineralization phase - Abstract: The Monte Sa Idda type swords belong to a well characterized typological class, whose origin has long been debated and seems to coincide with the Iberian Peninsula. The name comes from the site of the first discovery of a hoard containing this type of swords, among other bronze artefacts, namely Monte Sa Idda, Decimoputzu-Cagliari, Italy. The swords were produced through fusion inside a casting mould. Such kind of casting mould has not been found in Sardinia, and this may suggests that finished objects were either imported or made using clay or sand casting mould. Moreover, the discovery of these types of sword, in hoards and in votive deposits, raises the problem of their functional use. It is unknown if the blades were intended to be used as weapons, and therefore subjected to cold working necessary for thinning and sharpening of the blade, or as ceremonial objects. In order to answer to these questions, a neutron diffraction experiment was performed on three swords belonging to the Monte Sa Idda type. The results obtained are presented and discussed in the paper.

36 MATERIALS SCIENCE↗

Submicron silica as high−capacity lithium storage material with superior cycling performance

Highlights: • The electrochemical performance of SiO{sub 2} is strongly associated with ball milling. • Submicron silica show superior cycling performance for lithium storage. • Mechanism of electrochemical performance of SiO{sub 2} depended on milling was discussed. - Abstract: Submicron silica (SiO{sub 2}) is prepared via directly milling bulk SiO{sub 2}, which is the major constituent of the abundant sand on the earth. The electrochemical lithium storage performance of SiO{sub 2} is found to be strongly associated with the ball milling treatment. The reversible capacity of SiO{sub 2} gradually increases from 163 to 803 mAh g{sup −1} as the milling time is extended from 0 to 72 h. For the SiO{sub 2} milled for 24 h, it exhibits excellent cycling performance with a discharge capacity of 602 mAh g{sup −1} over 150 cycles, corresponding to the capacity retention of 99.8% relative to the 2nd cycle. The different particle sizes distribution and electrochemical activity of SiO{sub 2} are responsible for the effect of ball milling on its electrochemical lithium storage performance such as reversible capacity, cycling stability, electrode polarization and initial Coulombic efficiency.

36 MATERIALS SCIENCE↗

Neutron calorimeter development at fission and fusion pulsed neutron sources

A neutron calorimeter fielded in pulsed neutron irradiation experiments at the National Ignition Facility (NIF) and White Sands Missile Range Fast Burst Reactor (WSMR FBR) is described, and results are provided and discussed. The calorimeter is modular in design to allow fielding of various neutron absorber materials and thicknesses, as well as use at both fission and fusion sources, all of which has been done. Neutron calorimeters designed for fission sources have been fielded at fusion sources as well, but these instances are not documented in available literature—making this work novel. The functional calorimeter consists of a neutron absorber and two sheathed, grounded thermocouples secured within a subassembly made of thermally insulating materials. This subassembly is placed into a sealed vessel for material and facility safety considerations. The device was fielded at NIF in four polar-direct-drive exploding pusher shots and eleven WSMR FBR pulses. Calorimeter data from NIF experiments show a discernable thermal response accredited to neutron heating within the first 10 s, but the data are dominated by noise from ambient X-ray heating after time = 10 s post-pulse. This response is highly consistent between shots and linearly related to incident neutron fluence and neutron absorber thickness. A temperature rise of 1.1E-2 K/(10 13 neutrons/cm 2 ) per millimeter of absorber thickness was determined for both 0.4 mm and 1 mm thick depleted uranium absorbers with linear best fit R 2 of 0.97 and 0.98 for each thickness and y-axis offsets of 8.8E-3 and 1.3E-2, respectively. WSMR FBR experiment data show a temperature rise of 6.2E-2 K/(10 13 neutrons/cm 2 ) with linear best fit R 2 of 0.14 and y-axis offset of 7.6E-3 for a calorimeter with a 1 mm thick enriched boron carbide ( 10 B 4 C) absorber, though it must be noted that device-to-device variability is significant at both facilities. So these data are also affected by noise on a similar timescale as at NIF, though the noise is significantly lesser in magnitude but oscillatory.

42 ENGINEERING↗

Determination of spallation neutron flux through spectral adjustment techniques

The Los Alamos Isotope Production Facility (IPF) creates medical isotopes using a proton beam impinged on a target stack. Spallation neutrons are created in the interaction of the beam with target. The use of these spallation neutrons to produce additional radionuclides has been proposed in this paper. However, the energy distribution and magnitude of the flux is not well understood. Finally, a modified SAND-II spectral adjustment routine has been used with radioactivation foils to determine the differential neutron fluence for these spallation neutrons during a standard IPF production run.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Dispersal of high-burnup fuel fragment surrogate particles during and after loss-of-coolant accident tests

The issue of fuel fragmentation, relocation, and dispersal is critical in the licensing and use of high-burnup (>62 GWd/MTU) nuclear fuel in light water reactors (LWRs). In this work, two test series are reported that examine the fragment dispersal during a burst event and an additional dispersal following the burst due to vibrations in the rod, such as those induced by accident recovery systems. To examine dispersal during the balloon and burst portion of a Loss-of-Coolant Accident event, HfO 2 fragments and yttria-stabilized zirconia pellets were filled into an as-fabricated cladding tube, which was then pressurized and subjected to loss-of-coolant accident testing in steam. Results from this test were found to be highly non-prototypic, and dispersal was both significantly more violent and significantly greater in magnitude than identified for actual fuel tests. These findings were attributed to the conservative (more dispersive) nature of the particles chosen for dispersal and to the details of the test conditions used that led to particularly wide bursts. Further, the second set of tests examined dispersal following the burst when vibrations were induced in the rod, primarily via recovery activities such as Emergency Core Cooling System actuation leading to rapid water addition. Post-burst dispersal testing was performed by inducing sinusoidal oscillations with 2–25 nm peak-to-peak amplitude and 2–5 Hz frequencies in pre-burst rods that had been refilled with HfO 2 fragments or high-burnup fragment surrogate mixture of HfO 2 fragments and yttria-stabilized zirconia sands. Testing revealed that rods with large burst openings (7 mm wide in this work) led to unmitigated dispersal from above the burst zone but that smaller bursts (5 mm wide), although still much larger than the mean fragment size of 3 mm, led to effectively no dispersal because of interparticle locking. Additionally, mixture and moisture were found to impact the amount of dispersal: mixtures increased dispersal, and moisture drastically reduced it. The implications of these findings on likely dispersal from actual fuel are discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Discrete element modeling of grain crushing and implications on reservoir compaction

Depletion-induced formation compaction is a concern for production in hydrocarbon reservoirs. In this study, numerical mechanical tests and digital samples are proposed as an alternative to uniaxial strain experiments for investigating the effects of compaction. We propose a grain crushing model with two-sized subgrains based on the discrete element method and bonded-particle model (DEM-BPM) and perform numerical single grain crushing tests to calibrate the model parameters against the experimental sand grain characteristic strength. Numerical uniaxial strain tests are used to predict porosity and permeability reduction caused by reservoir compaction. Grain crushing incurs a significant reduction of porosity under the uniaxial strain stress path, which becomes more evident for digital samples consisting of larger grains. The stress-dependent changes in porosity and permeability obtained from the DEM simulations can be used as inputs for a reservoir-scale correlation to predict the productivity loss due to reservoir compaction.

nuclear (including radiation effects), carbon sequ↗

System response to gas production from a heterogeneous hydrate accumulation at the UBGH2-6 site of the Ulleung basin in the Korean East Sea

In this work, we investigate the feasibility of production from a layered marine gas hydrate reservoir using the properties and conditions corresponding to the UBGH2-6 site of the Ulleung Basin in the Korean East Sea. The work expands and furthers previous investigations in support of a proposed field test. The target system is location in deep water and consists of 13 m of alternating hydrate-bearing sand and soft mud layers and will be produced using a vertical well. We assess production potential during a 14-day field test, examine sensitivity to heterogeneity in permeability, porosity, and initial hydrate saturation, and assess the geomechanical response of the system to short-term production. Producing gas from the system appears to be technically feasible, however, low production rates and relatively large water production rates are expected during the field test. Expected subsidence and reservoir compaction is limited given the current data and the short timeframes of the production test.

02 PETROLEUM↗

Design of a gas-solid-solid separator to remove ash from circulating fluidized bed reactors

Cyclones are one of the most common types of gas-solid separators used in circulating fluidized bed boilers. However, cyclones typically do not allow ash to leave the system through the cyclone exit, causing ash to build up in the fluidized bed and necessitating additional systems to remove ash that builds up in the bed. In this study, an alternative “disengager” gas-solid separator is proposed as a way of inherently separating small and large solids, resulting in a gas-solid-solid separation system where ash is allowed to leave the system along with gas while the desired fluidized bed material is retained. Unlike cyclones, which rely on centrifugal force to separate solids and gas, the disengager separates based on entrainment velocity of the particles. Upwards-flowing gas and particles strike a deflection plate and enter the disengaging chamber where particles with low terminal velocity such as ash fines flow with the gas, while larger particles such as sand fall to the bottom of the separator and are returned to the fluidized bed. In this study, several different proposed disengager configurations are simulated and compared to a typical cyclone using computational fluid dynamic (CFD) simulations. Furthermore, it was found that separation efficiency in the disengager is strongly influenced by the size of the deflection plate, rather than by the size of the unit itself. The predicted separation efficiency showed that compared to a cyclone, the disengager design allows significantly more ash to exit the system but retains a similar amount of desirable material. Additionally, the disengager was predicted to not suffer significantly more erosion that a cyclone.

42 ENGINEERING↗

SPH modeling of biomass granular flow: Theoretical implementation and experimental validation

The commercialization of biomass-derived energy is impeded by flowability challenges arising from the feeding and handling of granular biomass materials in full-scale biorefineries. To overcome these obstacles, a robust and accurate model to simulate the flow of granular biomass is indispensable. However, conventional mesh-based numerical codes are limited by inherent mesh distortion in simulating large deformation that commonly occurs in granular biomass handling. Here, in this study, we propose a graphics processing unit (GPU)-accelerated meshless Smoothed Particle Hydrodynamics (SPH) code to model the flow of granular biomass materials. A modified void ratio-based mass conversation, a hybrid particle-to-particle/surface frictional boundary treatment, and a hypoplastic constitutive model are implemented. Four numerical examples, an elastic block sliding on inclined planes, sand column collapse, Angle of Repose, and axial compression tests for pine chips, were simulated using the developed SPH code. The results demonstrate good agreement between numerical predictions and analytical and experimental data for all four examples, validating the SPH code and increasing confidence that it can be applied to simulate more complex granular biomass handling processes, such as hopper feeding or auger conveyance.

09 BIOMASS FUELS↗

Thorium: Crustal abundance, joint production, and economic availability

Recently, interest in thorium's potential use in a nuclear fuel cycle has been renewed. Thorium is more abundant, at least on average, than uranium in the earth's crust and, therefore, could theoretically extend the use of nuclear energy technology beyond the economic limits of uranium resources. This paper provides an economic assessment of thorium availability by creating cumulative-availability and potential mining-industry cost curves, based on known thorium resources. These tools provide two perspectives on the economic availability of thorium. In the long term, physical quantities of thorium likely will not be a constraint on the development of a thorium fuel cycle. In the medium term, however, thorium supply may be limited by constraints associated with its production as a by-product of rare earth elements and heavy mineral sands. As a result, environmental concerns, social issues, regulation, and technology also present issues for the medium and long term supply of thorium.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Integrating fine root diameter and watershed mapping to characterize rhizosphere hydrology

Root morphology and soil hydraulic characteristics were integrated using watershed distance mapping to show water distribution and uptake across the plant-soil interface. Poplar (Populus deltoides, P. trichocarpa), maize (Zea mays), juniper (Juniperus virginiana), grape (Vitis rotundifolia) and maple (Acer saccharum) seedlings were grown in sand, after which root diameter and soil water dynamics were assessed via sequential neutron radiography. Three local soil regions (root-soil interface or edge, rhizosphere, bulk soil) were classified based on both radial distance from the root surface and diameter of the nearest root, from which changes in water content and distribution were characterized using digital image processing. Water content dynamics across the rhizosphere showed two different species-independent processes: a consistently elevated water content at the root-soil edge interface which increased with root diameter, and hysteresis as the rhizosphere transitioned to bulk soil (~0.5 cm from the root), independent of root diameter. Water uptake per unit root surface area declined exponentially with root diameter, independent of species. Results highlight the species-independent hydrologic characteristics of the rhizosphere and the potential for evaluating them in a local spatially connected soil context. Avenues for improved integration of soil and root characteristics are discussed.

59 BASIC BIOLOGICAL SCIENCES↗

Environmental impact of ongoing sources of metal contamination on remediated sediments

One challenge to all remedial approaches for contaminated sediments is the continued influx of contaminants from uncontrolled sources following remediation. We investigated the effects of ongoing contamination in mesocosms employing sediments remediated by different types of active and passive caps and in-situ treatment. Our hypothesis was that the sequestering agents used in active caps and in situ treatment will bind elements (arsenic, chromium, cadmium, cobalt, copper, nickel, lead, selenium, and zinc) from ongoing sources thereby reducing their bioavailability and protecting underlying remediated sediments from recontamination. Most element concentrations in surface water remained significantly lower in mesocosms with apatite and mixed amendment caps than in mesocosms with passive caps (sand), uncapped sediment, and spike solution throughout the 2520 hour experiment. Element concentrations were significantly higher in Lumbriculus variegatus from untreated sediment than in Lumbriculus from most active caps. Moreover, Pearson correlations between element concentrations in Lumbriculus and metal concentrations in the top 2.5 cm of sediment or cap measured by diffusive gradient in thin films (DGT) sediment probes were generally strong (as high as 0.98) and significant (p<0.05) for almost all tested elements. Metal concentrations in both Lumbriculus and sediment/cap were lowest in apatite, mixed amendment, and activated carbon treatments. Finally, these findings show that some active caps can protect remediated sediments by reducing the bioavailable pool of metals/metalloids in ongoing sources of contamination.

54 ENVIRONMENTAL SCIENCES↗

Dual in-aquifer and near surface processes drive arsenic mobilization in Cambodian groundwaters

Millions of people globally, and particularly in South and Southeast Asia, face chronic exposure to arsenic from reducing groundwaters in which. Arsenic release to is widely attributed largely to reductive dissolution of arsenic-bearing iron minerals, driven by metal reducing bacteria using bioavailable organic matter as an electron donor. However, the nature of the organic matter implicated in arsenic mobilization, and the location within the subsurface where these processes occur, remains debated. In a high resolution study of a largely pristine, shallow aquifer in Kandal Province, Cambodia, we have used a complementary suite of geochemical tracers (including 14 C, 3 H, 3 He, 4 He, Ne, δ 18 O, δD, CFCs and SF 6 ) to study the evolution in arsenic-prone shallow reducing groundwaters along dominant flow paths. The observation of widespread apparent 3 H- 3 He ages of <55years fundamentally challenges some previous models which concluded that groundwater residence times were on the order of hundreds of years. Surface-derived organic matter is transported to depths of >30m, and the relationships between age-related tracers and arsenic suggest that this surface-derived organic matter is likely to contribute to in-aquifer arsenic mobilization. A strong relationship between 3 H- 3 He age and depth suggests the dominance of a vertical hydrological control with an overall vertical flow velocity of ~0.4±0.1m·yr-1 across the field area. A calculated overall groundwater arsenic accumulation rate of ~0.08±0.03μM·yr -1 is broadly comparable to previous estimates from other researchers for similar reducing aquifers in Bangladesh. Although apparent arsenic groundwater accumulation rates varied significantly with site (e.g. between sand versus clay dominated sequences), rates are generally highest near the surface, perhaps reflecting the proximity to the redox cline and/or depth-dependent characteristics of the OM pool, and confounded by localized processes such as continued in-aquifer mobilization, sorption/desorption, and methanogenesis.

54 ENVIRONMENTAL SCIENCES↗