Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Realizability Analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

Preconditioning for the Navier-Stokes equations with finite-rate chemistry

The preconditioning procedure for generalized finite-rate chemistry and the proper preconditioning for the one-dimensional Navier-Stokes equations are presented. Eigenvalue stiffness is resolved and convergence-rate acceleration is demonstrated over the entire Mach-number range from the incompressible to the hypersonic. Specific benefits are realized at low and transonic flow speeds. The extended preconditioning matrix accounts for thermal and chemical non-equilibrium and its implementation is explained for both explicit and implicit time marching. The effect of higher-order spatial accuracy and various flux splittings is investigated. Numerical analysis reveals the possible theoretical improvements from using proconditioning at all Mach numbers. Numerical results confirm the expectations from the numerical analysis. Representative test cases include flows with previously troublesome embedded high-condition-number regions.

Godfrey, Andrew G.↗

Design and Experimental Demonstration of an Additive Manufactured Smart Oxy-Methane Burner for High Pressure and Supercritical Combustion

Pressurized oxy combustion-based systems can improve efficiency by recovering latent heat of the steam in the Flue Gas and achieving 90% CO2 capture. In addition, the novel Directly Heated Supercritical Carbon Dioxide (DH-SCO2) power cycles can achieve high thermal efficiencies and provide nearly full carbon capture. Additionally, due to the reduction of flue gas at higher pressure, smaller system size and capital cost reductions are also possible. Recent thermodynamic analysis of the DH-SCO2 cycle performed by the UTEP research team shows that combustion conditions in the vicinity of 300 bar pressure and 1000-1400 K temperature allow for relatively high system efficiencies while operating within the limit of available combustor materials. However, the realization of a directly heated supercritical power cycle requires combustion systems to operate in supercritical conditions and at temperature far below the blowout limit of conventional flames (above 1500 K). The thermodynamic properties along with the combustion properties and kinetics are unexplored at such conditions. Additionally, the interaction of the supercritical environment with energy components is also unknown. High-pressure combustion tests are performed using a smart burner at some intermediate pressure ranges (<20 bar) to help minimize these knowledge gaps. The knowledge obtained from the high-pressure test will assist in understanding the combustion chamber pressurization mechanism, ignition and flame behavior at the elevated pressure. The obtained data will act as a systematic first step in testing at higher pressures of 100 and 300 bar pressures.The primary purpose of this Dissertation is to demonstrate the operability of a low NOx smart burner for oxy-methane combustion at high pressure (< 20 bar) and scalable up to supercritical conditions. A shear co-axial smart burner is designed with a real-time temperature monitoring capability to understand the burner face interaction at high-pressure conditions. In addition, the burner has four independent injection ports to allow the independent injection of fuel and dilution gases in the combustor. The maximum operating capability of the burner is 575 kWth. The burner was fabricated using a Laser Powder Bed Fusion process with Nickel Alloy 718. A powder removal technology was invented comprising ultrasonic vibration, liquid nitrogen exposure and media blasting to remove powders from internal channels of the burner. The burner operability tests are performed in the high-pressure combustor and the swirl combustor. The high-pressure combustor was used to investigate the burner operability and thermal soak back at different pressurized conditions. The experimental tests in high-pressure combustor up to 275 kWth input resulted in 16.5 bar chamber pressure and 198°C thermal soaks back to the burner. The burner was capable of providing the required thermal input within a 3% deviation range. In addition, soot formation occurred at high-pressure tests. The swirl combustor was used to observe the flame stability of the burner. Flame lift-off was observed for jet velocities above 450 m/s. Additionally, lift-off decreased for low co-flow velocities. CO2 dilution experiments showed increased flame instabilities for all conditions above 50% dilution ratios. At lower thermal inputs, partial flame blow-offs occurred for dilution ratios above 50%. All conditions significantly reduced the flame temperature and increased the flame lift-off height. Finally, a 2nd generation AM smart burner was designed using the knowledge from the 1st generation burner experiments. The 2nd generation burner incorporated two sets of swirlers with 0.9 swirl no. A cooling system was also designed for long-duration tests at higher pressures. The thermal input and division of the burner's power are kept the same as the 1st generation burner. The burner is to be fabricated using nickel-alloy 718 for high-pressure handling capability. The design can sustain at high-pressure conditions up to 100 bar.

Islam, Md Nawshad Arslan↗

Achieving 50% Energy Savings in Chicago Homes: A Case Study for Advancing Equity and Climate Goals

Since 2019, the National Renewable Energy Laboratory (NREL) and Elevate have collaborated to identify pathways to deep energy retrofits in Chicago's housing stock, document equity implications and co-benefits of this transition, and validate the findings by implementing retrofits in real Chicago homes. This document summarizes our analysis process to model advanced retrofit packages that lead to greater than 50% energy savings in Chicago homes. Based on these findings, we have also developed a roadmap with the City to guide implementation, and are deploying the recommended retrofit packages in real Chicago homes to realize these energy savings. This work was developed in collaboration with two key stakeholders - the City of Chicago and Commonwealth Edison (ComEd) - and funded by the U.S. Department of Energy (DOE). NREL's Residential Buildings team maintains the best-in-class ResStock™ energy model of the U.S. residential building stock. For this work, we calibrated ResStock to Chicago's unique local housing stock to accurately simulate energy use in Chicago homes both for current conditions and with various retrofit scenarios. We simulated a wide range of potential building retrofits covering all aspects of residential energy use and then grouped these into packages based on energy and utility bill savings. ResStock can model diverse building types and housing characteristics, so we're able to observe the range of outcomes that might occur when these upgrades are deployed across the entire housing stock. We can then estimate potential energy savings from an advanced retrofit program on Chicago's housing stock by comparing the modeled energy use before versus after a retrofit. This novel version of ResStock, calibrated to Chicago with data from Elevate, can help City officials, ComEd, and other partners plan for community-scale decarbonization via residential retrofits. Specifically, this work contributes the following project goals: Develop a building retrofit prioritization strategy for Chicago single-family and 2- to 4-unit buildings; Identify neighborhoods and home types that have the highest potential for savings from electrification; and Assess the impact of advanced building retrofits on energy use, utility bills, and CO2 emissions at the city and building level. Although this study is specific to Chicago, its methods and learnings are applicable across the United States. These findings are especially notable for heat pumps and electrification retrofits in cold climates.

building energy modeling↗

High-burnup core design using minor actinide-containing metal fuel

A neutronic design study of metal fuel fast reactor (FR) cores is conducted on the basis of an innovative fuel design concept to achieve an extremely high burnup and realize an efficient fuel cycle system. Since it is expected that the burnup reactivity swing will become extremely large in an unprecedented high burnup core, minor actinides (MAs) from light water reactors (LWRs) are added to fresh fuel to improve the core internal conversion. Core neutronic analysis revealed that high burnups of about 200 MWd/kg for a small-scale core and about 300 MWd/kg for a large-scale core can be attained while suppressing the burnup reactivity swing to almost the same level as that of conventional cores with normal burnup. An actinide burnup analysis has shown that the MA consumption ratio is improved to about 60% and that the accumulated MAs originating from LWRs can be efficiently consumed by the high-burnup metal fuel FR. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Pilot Business Case Analysis for Digital Infrastructure

The Inflation Reduction Act Has Provided an Opening to Dramatically Change and Improve the Economics of Nuclear Power Until recently, the commercial nuclear sector has faced unprecedented financial challenges driven by low natural gas prices and subsidized renewables, in a marketplace that did not reward carbon-free baseload capacity. The industry is also plagued by labor shortages, increasingly obsolete labor-centric operating models and antiquated analog technology that threaten the viability of the long-term operations of domestic nuclear facilities. In this context, the economic survival of nuclear power plants requires an efficient and technology-centric operating model that harvests the native efficiencies of advanced technology. Such transformations have been made in many other industries – notably, oil and gas. The passage by Congress of the Inflation Reduction Act (IRA) in 2022 provides nuclear operators with unprecedented economic incentives to pursue these upgrades. To realize the benefits of these incentives and achieve the necessary transformations in the nuclear operating model, the nuclear industry must overcome both the continuing unease about licensing pathways and uncertainty related to implementation costs.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Results from the third Galaxy Serpent tabletop exercise demonstrating the utility of nuclear forensics libraries in support of an investigation

Galaxy Serpent is a virtual, web-based international ongoing series of tabletop exercises designed to mature the concept of National Nuclear Forensics Libraries (NNFL) and illustrate their utility in answering investigative questions or providing investigative leads as part of an investigation involving nuclear or other radioactive material (R/N) out of regulatory control (MORC). Two prior versions of the exercise have been conducted; the first utilizing surrogate data for spent nuclear fuel as the material of interest, and the second using synthetic sealed radioactive source data. Teams participating in the recently concluded third version of the exercise were provided with synthetic uranium ore concentrate (UOC) data mimicking actual data characteristics (e.g. trace element concentrations), which was used to compile a model NNFL. Teams decided how to organize and interpret the data they were provided, dealt with real world features such as missing data, and assessed discriminating attributes. Next, a hypothetical scenario involving three UOC samples found out of regulatory control was provided, and each team had to assess the self-consistency of the individual sources in the unknown data, and employ their model NNFL as a comparative assessment instrument to determine whether the three UOC materials in question were consistent with any of the types of materials in their library. In conclusion, the design of the exercise, methodologies utilized by participating teams, and aggregate results of the exercise will be presented, along with challenges encountered and benefits realized.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

Parametric study of flow patterns behind the standing accretion shock wave for core-collapse supernovae

In this study, we conduct three-dimensional hydrodynamic simulations systematically to investigate the flow patterns behind the accretion shock waves that are commonly formed in the post-bounce phase of core-collapse supernovae. Adding small perturbations to spherically symmetric, steady, shocked accretion flows, we compute the subsequent evolutions to find what flow pattern emerges as a consequence of hydrodynamical instabilities such as convection and standing accretion shock instability for different neutrino luminosities and mass accretion rates. Depending on these two controlling parameters, various flow patterns are indeed realized. We classify them into three basic patterns and two intermediate ones; the former includes sloshing motion (SL), spiral motion (SP), and multiple buoyant bubble formation (BB); the latter consists of spiral motion with buoyant-bubble formation (SPB) and spiral motion with pulsationally changing rotational velocities (SPP). Although the post-shock flow is highly chaotic, there is a clear trend in the pattern realization. The sloshing and spiral motions tend to be dominant for high accretion rates and low neutrino luminosities, and multiple buoyant bubbles prevail for low accretion rates and high neutrino luminosities. It is interesting that the dominant pattern is not always identical between the semi-nonlinear and nonlinear phases near the critical luminosity; the intermediate cases are realized in the latter case. Running several simulations with different random perturbations, we confirm that the realization of flow pattern is robust in most cases.

79 ASTRONOMY AND ASTROPHYSICS↗

Ghost imaging of phase objects with classical incoherent light

We describe an optical setup for performing spatial Fourier filtering in ghost imaging with classical incoherent light. This is achieved by a modification of the conventional geometry for lensless ghost imaging. It is shown on the basis of classical coherence theory that with this technique one can realize what we call phase-contrast ghost imaging to visualize pure phase objects.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Computational Fluid Dynamics Analysis of the Molten Salt Tritium Transport Experiment Test Section

Tritium, a radionuclide produced through neutron capture by lithium and other elements (beryllium and fluoride) in molten salts, presents unique challenges to radionuclide release. This is true for both fusion energy breeder blankets and molten salt fission reactors. The fundamental understanding of tritium transport is crucial to the safe design and operation of these reactors. The Molten Salt Tritium Transport Experiment (MSTTE), currently under construction at Idaho National Laboratory, aims to investigate tritium transport phenomena using a forced-convection fluoride salt loop. This loop is designed to study various transport mechanisms, such as permeation through metals and gas-liquid interactions, and is intended to support future research on tritium extraction units. A critical aspect of the MSTTE loop design is ensuring a fully developed velocity profile before the fluid reaches the permeation test section where measurements are made. This study employs computational fluid dynamics to model the salt flow behavior within the MSTTE permeation test section. A realizable k-ε turbulent model with enhanced wall treatment is used to simulate the single-phase, vertical upward flow of molten salt FLiNaK under isothermal conditions. The simulation results indicated flow distortion and underdeveloped profiles at all planned flow rates within the test section due to the 85-deg sharp bend. To address this issue, a reduced diameter with a reducer and expander and a flow conditioner are investigated to achieve fully developed flow. The analysis showed that the flow conditioner successfully corrected the flow profile, achieving fully developed behavior at a flow rate of 50 liters per minute (LPM). In conclusion, this research enhances our understanding of flow dynamics in molten salt systems and contributes to optimizing tritium transport control technologies.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Analysis of impactor residues in tray clamps from the Long Duration Exposure Facility. Part 2: Clamps from Bay B of the satellite

The Long Duration Exposure Facility (LDEF) was placed in low-Earth orbit (LEO) in 1984 and recovered 5.7 years later. The LDEF was host to several individual experiments specifically designed to characterize critical aspects of meteoroid and debris environment in LEO. However, it was realized from the beginning that the most efficient use of the satellite would be to examine the entire surface for impact features. In this regard, particular interest centered on common exposed materials that faced in all LDEF pointing directions. Among the most important of these materials was the tray clamps. Therefore, in an effort to better understand the nature of particulates in LEO and their effects on spacecraft hardware, residues found in impact features on LDEF tray clamp surfaces are being analyzed. This catalog presents all data from clamps from Bay B of the LDEF. NASA Technical Memorandum 104759 has cataloged impacts that occurred on Bay B (published March 1993). Subsequent catalogs will include clamps from succeeding bays of the satellite.

Bernhard, Ronald P.↗

Anisotropic Excitons Reveal Local Spin Chain Directions in a van der Waals Antiferromagnet

A long‐standing pursuit in materials science is to identify suitable magnetic semiconductors for integrated information storage, processing, and transfer. Van der Waals magnets have brought forth new material candidates for this purpose. Recently, sharp exciton resonances in antiferromagnet NiPS 3 have been reported to correlate with magnetic order, that is, the exciton photoluminescence intensity diminishes above the Néel temperature. Here, it is found that the polarization of maximal exciton emission rotates locally, revealing three possible spin chain directions. This discovery establishes a new understanding of the antiferromagnet order hidden in previous neutron scattering and optical experiments. Furthermore, defect‐bound states are suggested as an alternative exciton formation mechanism that has yet to be explored in NiPS 3 . The supporting evidence includes chemical analysis, excitation power, and thickness dependent photoluminescence and first‐principles calculations. This mechanism for exciton formation is also consistent with the presence of strong phonon side bands. This study shows that anisotropic exciton photoluminescence can be used to read out local spin chain directions in antiferromagnets and realize multi‐functional devices via spin‐photon transduction.

36 MATERIALS SCIENCE↗

Spectral fluctuations in the Sachdev-Ye-Kitaev model

We present a detailed quantitative analysis of spectral correlations in the Sachdev-Ye-Kitaev (SYK) model. We find that the deviations from universal Random Matrix Theory (RMT) behavior are due to a small number of long-wavelength fluctuations (of the order of the number of Majorana fermions N ) from one realization of the ensemble to the next one. These modes can be parameterized effectively in terms of Q-Hermite orthogonal polynomials, the main contribution being due to scale fluctuations for which we give a simple analytical estimate. Our numerical results for N = 32 show that only the lowest eight polynomials are needed to eliminate the nonuniversal part of the spectral fluctuations. The covariance matrix of the coefficients of this expansion can be obtained analytically from low-order double-trace moments. We evaluate the covariance matrix of the first six moments and find that it agrees with the numerics. We also analyze the spectral correlations in terms of a nonlinear σ-model, which is derived through a Fierz transformation, and evaluate the one and two-point spectral correlation functions to two-loop order. The wide correlator is given by the sum of the universal RMT result and corrections whose lowest-order term corresponds to scale fluctuations. However, the loop expansion of the σ-model results in an ill-behaved expansion of the resolvent, and it gives universal RMT fluctuations not only for q= 4 or higher even q-body interactions, but also for the q= 2 SYK model albeit with a much smaller Thouless energy while the correct result in this case should have been Poisson statistics. In our numerical studies we analyze the number variance and spectral form factor for N = 32 and q = 4. We show that the quadratic deviation of the number variance for large energies appears as a peak for small times in the spectral form factor. After eliminating the long-wavelength fluctuations, we find quantitative agreement with RMT up to an exponentially large number of level spacings for the number variance or exponentially short times in the case of the spectral form factor.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Structure-property relationship between lignin structures and properties of 3D-printed lignin composites

Lignin is a low-cost and renewable bioresource with a huge annual production promising to prepare sustainable materials. However, the poor interfacial adhesion between many lignin-polymer pairs deteriorates the mechanical performance of the composites, which seriously limits the application of lignin in 3D printing via fused depositional modeling. This work examined lignin-polyamide 12 (PA 12) intermolecular interactions (e.g., hydrogen bonding) to address the interface challenge. To realize this goal, the phenolic hydroxyl content was increased for a kraft softwood lignin using a LiBr/HBr demethylation procedure, increasing phenoxy content by 61.7%. Increased hydrogen bonding interactions between modified lignin (Pine-Lig-OH) and PA 12 demonstrated a significantly improved molten dynamic modulus by rheological analysis. Regarding mechanical properties, by adding 20 wt% of Pine-Lig-OH, the tensile strength and Young's modulus reached 46.6 MPa and 1.62 GPa, 30.2% and 33.9% higher than PA 12, respectively. Further morphological analysis proved the interfacial interactions are enhanced by showing the difference in the phase gaps. The dynamic mechanical analysis (DMA) supported the conclusion that Pine-Lig-OH could interact with polymer chains, alternating segmental movements due to the strong interaction. Here, this study presents a method to enhance lignin composite properties by promoting interactions with the polymer matrix through modified functional groups, guiding future lignin composite research.

36 MATERIALS SCIENCE↗

Sequence-Dependent Structure/Function Relationships of Catalytic Peptide-Enabled Gold Nanoparticles Generated under Ambient Synthetic Conditions

Peptide-enabled nanoparticle (NP) synthesis routes can create and/or assemble functional nanomaterials under environmentally friendly conditions, with properties dictated by complex interactions at the biotic/abiotic interface. Manipulation of this interface through sequence modification can provide the capability for material properties to be tailored to create enhanced materials for energy, catalysis, and sensing applications. Fully realizing the potential of these materials requires a comprehensive understanding of sequence-dependent structure/function relationships that is presently lacking. In this work, the atomic-scale structures of a series of peptide-capped Au NPs are determined using a combination of atomic pair distribution function analysis of high-energy X-ray diffraction data and advanced molecular dynamics (MD) simulations. The Au NPs produced with different peptide sequences exhibit varying degrees of catalytic activity for the exemplar reaction 4-nitrophenol reduction. The experimentally derived atomic-scale NP configurations reveal sequence-dependent differences in structural order at the NP surface. Replica exchange with solute-tempering MD simulations are then used to predict the morphology of the peptide overlayer on these Au NPs and identify factors determining the structure/catalytic properties relationship. We show that the amount of exposed Au surface, the underlying surface structural disorder, and the interaction strength of the peptide with the Au surface all influence catalytic performance. A simplified computational prediction of catalytic performance is developed that can potentially serve as a screening tool for future studies. Our approach provides a platform for broadening the analysis of catalytic peptide-enabled metallic NP systems, potentially allowing for the development of rational design rules for property enhancement.

Bedford, Nicholas M.↗

Frieze charge-stripes in a correlated kagome superconductor

In kagome metals, geometric frustration, electronic correlations and band topology combine to produce a wide range of intriguing phenomena. Among them, CsCr$_3$Sb$_5$ offers an opportunity to investigate unconventional superconductivity in a strongly correlated kagome system, with indications of frustrated magnetism and quantum criticality. Here, we demonstrate a cascade of density-wave transitions with distinct symmetries in bulk single crystals of CsCr$_3$Sb$_5$. Using spectroscopic imaging scanning tunneling microscopy, we uncover a unidirectional density wave that breaks all mirror symmetries -- resembling a chiral density wave -- but that also retains a mirror glide symmetry. We refer to this as a frieze charge stripe order phase, as its symmetry properties correspond to one of the fundamental frieze symmetry groups. A combination of high-resolution imaging, Fourier analysis and theoretical simulations reveal the key role of sublattice degrees of freedom in stabilizing this phase, characterized by internal chiral textures of opposite handedness. These findings suggest that superconductivity in CsCr$_3$Sb$_5$ emerges from this distinct density wave state and provide fresh insight into realizing electronic phases governed by frieze symmetry groups in quantum materials.

Cheng, Siyu [Boston College, Chestnut Hill, MA (Un↗

Characteristics of a liquid-helium-free calibration apparatus for cryogenic thermometers

Closed-cycle Joule-Thomson (JT) cryocoolers have been developed at National Metrology Institute of Japan (NMIJ)/National Institute of Advanced Industrial Science and Technology (AIST) with the aim of realizing a liquid-helium-free calibration apparatus for cryogenic thermometers between 0.65 K and 25 K. The latest JT cryocooler at NMIJ/AIST consists of a {sup 3}He JT cooling circuit and a pulse tube mechanical refrigerator. The characteristics of the apparatus including a residual gas analysis of the JT cooling circuit are presented in this paper. Currently the initial cool-down is performed using a heat-exchange gas. It normally takes about 30 h to reduce the temperature from room temperature to 5 K at the thermometer comparison block of the apparatus. The correct timing of the removal of the heatexchange gas is important for the efficient operation of the apparatus. Incomplete removal of the heat-exchange gas induces excess heat load on the apparatus and thermal disturbances. Some examples of abrupt temperature bursts are discussed in this paper. Mechanical refrigerators generate cyclic mechanical vibrations, and precision resistance thermometers are usually very sensitive to a mechanical vibration. The measured vibration level of the developed apparatus is reported. The damage to the apparatus due to the magnitude 9.0 earthquake on March 11, 2011, and possible countermeasures in the case of future earthquakes are also discussed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Decaying dark matter and the PAMELA anomaly

Astrophysical and cosmological observations do not require the dark matter particles to be absolutely stable. If they are indeed unstable, their decay into positrons might occur at a sufficiently large rate to allow the indirect detection of dark matter through an anomalous contribution to the cosmic positron flux. In this paper we discuss the implications of the excess in the positron fraction recently reported by the PAMELA collaboration for the scenario of decaying dark matter. To this end, we have performed a model-independent analysis of possible signatures by studying various decay channels in the case of both a fermionic and a scalar dark matter particle. We find that the steep rise in the positron fraction measured by PAMELA at energies larger than 10 GeV can naturally be accommodated in several realizations of the decaying dark matter scenario. The data point toward a rather heavy dark matter particle, m{sub DM} {approx}> 300 GeV, which preferentially decays directly into first or second generation charged leptons with a lifetime {tau}{sub DM} {approx} 10{sup 26} s.

79 ASTRONOMY AND ASTROPHYSICS↗

Unraveling trace anomaly of supradense matter via neutron star compactness scaling

The trace anomaly Δ ≡ 1/3 −𝑃/𝜖 =1/3 −𝜙 quantifies the possibly broken conformal symmetry in supradense matter under pressure 𝑃 at energy density 𝜖. Perturbative QCD (pQCD) predicts a vanishing Δ at extremely high energy or baryon densities when the conformal symmetry is realized but its behavior at intermediate densities reachable in neutron stars (NSs) is still very uncertain. The extraction of Δ from NS observations strongly depends on the employed model for nuclear equation of state (EOS). Using the IPAD-TOV method based on an intrinsic and perturbative analysis of the dimensionless (IPAD) Tolman-Oppenheimer-Volkoff (TOV) equations that are further verified numerically by using 10 5 EOSs generated randomly with a metamodel in a very broad EOS parameter space constrained by terrestrial nuclear experiments and astrophysical observations, here we first show that the compactness 𝜉 ≡ 𝐺⁡𝑀 NS /𝑅⁢𝑐 2 ≡ 𝑀 NS /𝑅 of a NS with mass 𝑀 NS and radius 𝑅 scales very accurately with $\bar{Π}$ c ≡ $Π$ c · (1 +18⁢X/25) ≡ X/(1 +3⁢X 2 +4⁢X) · (1 +18⁢X/25) where X ≡ 𝜙 c = 𝑃 c /𝜖 c is the ratio of pressure over energy density at NS centers. The scaling of NS compactness thus enables one to readily read off the central trace anomaly Δ c = 1/3 −X directly from the observational data of either the mass-radius or red-shift measurements. Finally, we then demonstrate indeed that the available NS data themselves from recent X-ray and gravitational wave observations can determine model insensitively the trace anomaly as a function of energy density in NS cores, providing a stringent test of existing NS models and a clear guidance in a new direction for further understanding the nature and EOS of supradense matter.

nuclear astrophysics↗