Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RETENTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

Controlled lithium stripping enables a stable interface for long-cycling anode-free solid-state batteries

Anode-free solid-state batteries (AFSSBs) are a promising route toward achieving high energy density. In these cells, the anode contains no pre-stored lithium (Li). Instead, the entire Li inventory originates from the cathode and is freshly deposited onto a bare current collector during charging. However, achieving uniform and defect-free Li plating on this bare current collector remains a major challenge, often resulting in low Li plating/stripping efficiency and rapid capacity decay. Here, for the first time, operando neutron imaging is employed to visualize Li plating/stripping behavior in an anode-free full cell with LiNi0.82Mn0.07Co0.11O2 (NMC) as the cathode. Operando measurements reveal that complete stripping of Li leaves isolated Li residues on the current collector, which degrades the interfacial contact between the current collector and the solid-state electrolyte. To mitigate this interfacial issue and promote more uniform Li deposition, we implement a discharge-cutoff-voltage strategy that intentionally retains a thin residual Li layer after stripping. This preserved Li-containing interfacial reservoir not only improves interfacial contact but also serves as an in situ formed seed layer that enables more homogeneous subsequent Li plating. As a result, the optimized anode-free cell with limited stripping depth exhibits excellent long-term cycling stability, maintaining a discharge capacity of 112.1 mAh g−1 with a capacity retention of 80.6% and an average coulombic efficiency of approximately 99.9% after 500 cycles at 0.25 C. In contrast, the cell with a conventional discharge cutoff voltage of 2.8 V exhibits rapid capacity decay, retaining only 59.7 mAh g−1 after 50 cycles with a capacity retention of 40.7%. This work demonstrates that limiting deep stripping to preserve a thin Li-containing interfacial layer can effectively improve the cycling stability of sulfide-based AFSSBs.

Wang, Jiwei [Northeastern University, Boston]↗

Improved reliability of Mo nanocrystal memory with ammonia plasma treatment

We investigated ammonia plasma treatment influence on the nonvolatile memory characteristics of the charge storage layer composed of Mo nanocrystals embedded in nonstoichiometry oxide (SiO{sub x}). X-ray photoelectron spectra analyses revealed that nitrogen was incorporated into the charge storage layer. Electric analyses indicated that the memory window was reduced and the retention and the endurance improved after the treatment. The reduction in the memory window and the improvement in retention were interpreted in terms of the nitrogen passivation of traps in the oxide around Mo nanocrystals. The robust endurance characteristic was attributed the improvement of the quality of the surrounding oxide by nitrogen passivation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Transparent photostable ZnO nonvolatile memory transistor with ferroelectric polymer and sputter-deposited oxide gate

We report on the fabrication of transparent top-gate ZnO nonvolatile memory thin-film transistors (NVM-TFTs) with 200 nm thick poly(vinylidene fluoride/trifluoroethylene) ferroelectric layer; semitransparent 10 nm thin AgO{sub x} and transparent 130 nm thick indium-zinc oxide (IZO) were deposited on the ferroelectric polymer as gate electrode by rf sputtering. Our semitransparent NVM-TFT with AgO{sub x} gate operates under low voltage write-erase (WR-ER) pulse of {+-}20 V, but shows some degradation in retention property. In contrast, our transparent IZO-gated device displays very good retention properties but requires anomalously higher pulse of {+-}70 V for WR and ER states. Both devices stably operated under visible illuminations.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Tritium issues in plasma wall interactions

Since tritium resources are very limited, not only for safety reason but also for tritium economy, tritium inventory in a reactor must be kept as small as possible. In the present tokamaks, however, hydrogen retention rate in their vacuum vessel is significantly large, i.e. more than 20% of fueled hydrogen is continuously piled up, which must not be allowed in a reactor. After the introduction of tritium as a hydrogen radioisotope, the paper summarizes present tritium issues in plasma wall interactions, in particular, fueling, retention and recovering, considering the handling of large amounts of tritium, i.e. confinement, leakage, contamination, permeation, regulations and tritium accountancy. Progress in overcoming such problems will be also presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Zinc-oxide charge trapping memory cell with ultra-thin chromium-oxide trapping layer

A functional zinc-oxide based SONOS memory cell with ultra-thin chromium oxide trapping layer was fabricated. A 5 nm CrO{sub 2} layer is deposited between Atomic Layer Deposition (ALD) steps. A threshold voltage (V{sub t}) shift of 2.6V was achieved with a 10V programming voltage. Also for a 2V V{sub t} shift, the memory with CrO{sub 2} layer has a low programming voltage of 7.2V. Moreover, the deep trapping levels in CrO{sub 2} layer allows for additional scaling of the tunnel oxide due to an increase in the retention time. In addition, the structure was simulated using Physics Based TCAD. The results of the simulation fit very well with the experimental results providing an understanding of the charge trapping and tunneling physics.

36 MATERIALS SCIENCE↗

Study of behavior and determination of customer lifetime value(CLV) using Markov chain model

Customer Lifetime Value or CLV is a restriction on interactive marketing to help a company in arranging financial for the marketing of new customer acquisition and customer retention. Additionally CLV can be able to segment customers for financial arrangements. Stochastic models for the fairly new CLV used a Markov chain. In this model customer retention probability and new customer acquisition probability play an important role. This model is originally introduced by Pfeifer and Carraway in 2000 [1]. They introduced several CLV models, one of them only involves customer and former customer. In this paper we expand the model by adding the assumption of the transition from former customer to customer. In the proposed model, the CLV value is higher than the CLV value obtained by Pfeifer and Caraway model. But our model still requires a longer convergence time.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Defect states and charge trapping characteristics of HfO{sub 2} films for high performance nonvolatile memory applications

In this work, we present significant charge trapping memory effects of the metal-hafnium oxide-SiO{sub 2}-Si (MHOS) structure. The devices based on 800 °C annealed HfO{sub 2} film exhibit a large memory window of ∼5.1 V under ±10 V sweeping voltages and excellent charge retention properties with only small charge loss of ∼2.6% after more than 10{sup 4 }s retention. The outstanding memory characteristics are attributed to the high density of deep defect states in HfO{sub 2} films. We investigated the defect states in the HfO{sub 2} films by photoluminescence and photoluminescence excitation measurements and found that the defect states distributed in deep energy levels ranging from 1.1 eV to 2.9 eV below the conduction band. Our work provides further insights for the charge trapping mechanisms of the HfO{sub 2} based MHOS devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A multi-technique analysis of deuterium trapping and near-surface precipitate growth in plasma-exposed tungsten

In this work, we examine how deuterium becomes trapped in plasma-exposed tungsten and forms near-surface platelet-shaped precipitates. How these bubbles nucleate and grow, as well as the amount of deuterium trapped within, is crucial for interpreting the experimental database. Here, we use a combined experimental/theoretical approach to provide further insight into the underlying physics. With the Tritium Plasma Experiment, we exposed a series of ITER-grade tungsten samples to high flux D plasmas (up to 1.5 × 10{sup 22 }m{sup −2} s{sup −1}) at temperatures ranging between 103 and 554 °C. Retention of deuterium trapped in the bulk, assessed through thermal desorption spectrometry, reached a maximum at 230 °C and diminished rapidly thereafter for T > 300 °C. Post-mortem examination of the surfaces revealed non-uniform growth of bubbles ranging in diameter between 1 and 10 μm over the surface with a clear correlation with grain boundaries. Electron back-scattering diffraction maps over a large area of the surface confirmed this dependence; grains containing bubbles were aligned with a preferred slip vector along the <111> directions. Focused ion beam profiles suggest that these bubbles nucleated as platelets at depths of 200 nm–1 μm beneath the surface and grew as a result of expansion of sub-surface cracks. To estimate the amount of deuterium trapped in these defects relative to other sites within the material, we applied a continuum-scale treatment of hydrogen isotope precipitation. In addition, we propose a straightforward model of near-surface platelet expansion that reproduces bubble sizes consistent with our measurements. For the tungsten microstructure considered here, we find that bubbles would only weakly affect migration of D into the material, perhaps explaining why deep trapping was observed in prior studies with plasma-exposed neutron-irradiated specimens. We foresee no insurmountable issues that would prevent the theoretical framework developed here from being extended to a broader range of systems where precipitation of insoluble gases in ion beam or plasma-exposed metals is of interest.

36 MATERIALS SCIENCE↗

Junction size dependence of ferroelectric properties in e-beam patterned BaTiO{sub 3} ferroelectric tunnel junctions

We investigate the switching characteristics in BaTiO{sub 3}-based ferroelectric tunnel junctions patterned in a capacitive geometry with circular Ru top electrode with diameters ranging from ∼430 to 2300 nm. Two different patterning schemes, viz., lift-off and ion-milling, have been employed to examine the variations in the ferroelectric polarization, switching, and tunnel electro-resistance resulting from differences in the pattering processes. The values of polarization switching field are measured and compared for junctions of different diameter in the samples fabricated using both patterning schemes. We do not find any specific dependence of polarization switching bias on the size of junctions in both sample stacks. The junctions in the ion-milled sample show up to three orders of resistance change by polarization switching and the polarization retention is found to improve with increasing junction diameter. However, similar switching is absent in the lift-off sample, highlighting the effect of patterning scheme on the polarization retention.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Deuterium uptake and sputtering of simultaneous lithiated, boronized, and oxidized carbon surfaces irradiated by low-energy deuterium

We study the effects of deuterium irradiation on D-uptake by simultaneously boronized, lithiated, oxidized, and deuterated carbon surfaces. We present analysis of the bonding chemistry of D for various concentrations of boron, lithium, oxygen, and deuterium on carbon surfaces using molecular dynamics with reactive force field potentials, which are here adapted to include the interaction of boron and lithium. We calculate D retention and sputtering yields of each constituent of the Li-C-B-O mixture and discuss the role of oxygen in these processes. The extent of the qualitative agreement between new experimental data for B-C-O-D obtained in this paper and computational data is provided. As in the case of the Li-C-O system, comparative studies where experimental and computational data complement each other (in this case on the B-Li-C-O system) provide deeper insights into the mechanisms behind the role that O plays in the retention of D, a relevant issue in fusion machines.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

FAST Irradiations, Postirradiation Examinations, and Modeling of U-Mo for Light Water Reactor Applications

Many next generation light water reactor (LWR) concepts, such as mobile small modular reactors, are seeking to use smaller core dimensions than conventional reactor types. Smaller reactor cores require an increase in fissile material to maintain reactivity. For non-proliferation purposes, enrichment increases are limited to less than 20% (high assay low enriched uranium, [HALEU]) and so higher uranium density fuels than UO 2 must be considered. To this end, uranium-molybdenum alloys were tested using the Fission Accelerated Steady-state Test (FAST) approach. The experiment test matrix is focused on identifying the temperature transition between low swelling and high fission gas retention to break away swelling and low fission gas retention. This paper documents the results of irradiation tests and post-irradiation examinations (PIE) including neutron radiography, rodlet profilometry, fission gas collection analysis, and optical metallography. The results of these tests showed that unconstrained U-Mo fuels (solid, Na-bonded rodlets) have a swelling threshold between 400-450°C with minimal fission gas release below this point. Higher temperature solid fuel showed microstructural zoning with small pore networks while lower temperature solid fuels have a uniform microstructure with large pore networks. U-Annular Mo fuels where swelling had some self-constraint imposed upon it, were shown to have much reduced swelling compared to their solid counterparts as well as very low fission gas release for irradiation temperatures up to 500°C. These initial results show that the use of U-Mo in constrained fuel geometries could be used as a high uranium density HALEU fuel for LWRs.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Loading Capacity and Dilute Nitric Acid Rinse of Diglycolamide Resin for the Recovery of Transplutonium and Rare Earth Elements from Mark-18A Targets

N,N,N′,N′-tetraoctyldiglycolamide (TODGA) as a resin (“DGA resin”) produced by Eichrom Technologies will be used by Savannah River National Laboratory for the indiscriminate extraction of trivalent actinides and rare earth elements with the intent of recovering Cm and Am from dissolved irradiated 242 Pu Mark-18A targets in 7 to 9 M nitric acid. The extracted constituents will be recovered as an oxide by direct thermal decomposition of the loaded resin followed by calcination of the resultant residue. The characteristics of DGA resin with non-radiological feed simulant representative of the anticipated feed in the Mark-18A process, with Sm and Nd as surrogates for Cm and Am, respectively, including breakthrough point and saturation capacity were evaluated in this work. Additionally, this work examined the losses from the loaded resin by rinsing the resin bed with dilute acid to reduce the nitrate concentration in the resin bed prior to thermal decomposition operations to improve the safety posture of the process. A resin loading profile was developed, and the resin was determined to have a trivalent metal saturation capacity of 74 μmol/mL resin under the experimental conditions evaluated. Following a wash of the loaded resin bed with fresh 8 M HNO 3 , the trivalent metals retained was reduced to 68 μmol/mL resin, which represents the practical capacity of the resin for the Mark-18A process. Lighter lanthanides breakthrough the resin well before the saturation capacity is reached. Rinsing the saturated resin bed with 0.26 M HNO 3 was found to result in a rapid reduction in retention of rare earth elements by the resin. After 2.8 bed volumes of dilute acid rinse, the mean resin bed free acid concentration was reduced to 0.28 M and 3.1 bed volumes of dilute acid rinse resulted in a reduction of the cumulative rare earth element retention to 52 μmol/mL of resin.

Transplutonium separations↗

Plasma-Material-Interaction Research Using PISCES Linear Plasma Devices

In this paper, recent plasma-material-interaction (PMI) studies of relevance to fusion PMI science are discussed. The results are a mix of science experiments and in situ diagnostic technology development. Scientific issues addressed include the nature of He and W atom migration in the evolution of W fuzz surfaces, understanding the nature of D retention in damaged W surfaces via modeling with the tritium migration and analysis program, and an examination of synergistic effects associated with D trapping on composite Be codeposit and W substrate surfaces. In situ diagnostic developments discussed include laser-induced desorption spectroscopy for the measurement of bulk hydrogen retention and laser-induced breakdown spectroscopy for the measurement of near-surface composition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

INTERACTION OF CLOSE-IN PLANETS WITH THE MAGNETOSPHERE OF THEIR HOST STARS. II. SUPER-EARTHS AS UNIPOLAR INDUCTORS AND THEIR ORBITAL EVOLUTION

Planets with several Earth masses and orbital periods of a few days have been discovered through radial velocity and transit surveys. Regardless of their formation mechanism, an important evolution issue is the efficiency of their retention in the proximity of their host stars. If these 'super-Earths' attained their present-day orbits during or shortly after the T Tauri phase of their host stars, a large fraction of these planets would have encountered an intense stellar magnetic field. These rocky planets have a higher conductivity than the atmosphere of their host stars and, therefore, the magnetic flux tube connecting them would slip though the envelope of the host stars faster than across the planets. The induced electromotive force across the planet's diameter leads to a potential drop which propagates along a flux tube away from the planet with an Alfven speed. The foot of the flux tube would sweep across the stellar surface and the potential drop across the field lines drives a DC current analogous to that proposed for the electrodynamics of the Io-Jupiter system. The ohmic dissipation of this current produces potentially observable hot spots in the star envelope. It also heats the planet and leads to a torque which drives the planet's orbit to evolve toward both circularization and a state of synchronization with the spin of the star. The net effect is the damping of the planet's orbital eccentricity. Around slowly (or rapidly) spinning stars, this process also causes rocky planets with periods less than a few days to undergo orbital decay (or expansion/stagnation) within a few Myr. In principle, this effect can determine the retention efficiency of short-period hot Earths. We also estimate the ohmic dissipation interior to these planets and show that it can lead to severe structure evolution and potential loss of volatile material in them. However, these effects may be significantly weakened by the reconnection of the induced field.

79 ASTRONOMY AND ASTROPHYSICS↗

Age and gender specific biokinetic model for strontium in humans

A biokinetic model for strontium in humans is necessary for quantification of internal doses due to strontium radioisotopes. The ICRP-recommended biokinetic model for strontium has limitation for use in a population study, because it is not gender specific and does not cover all age ranges. The extensive Techa River data set on 90Sr in humans (tens of thousands of measurements) is a unique source of data on long-term strontium retention for men and women of all ages at intake. These, as well as published data, were used for evaluation of age- and gender-specific parameters for a new compartment biokinetic model for strontium (Sr-AGe model). The Sr-AGe model has similar structure as the ICRP model for the alkaline earth elements. The following parameters were mainly reevaluated: gastro-intestinal absorption and parameters related to the processes of bone formation and resorption defining calcium and strontium transfers in skeletal compartments. The Sr-AGe model satisfactorily describes available data sets on strontium retention for different kinds of intake (dietary and intravenous) at different ages (0–80 years old) and demonstrates good agreement with data sets for different ethnic groups. The Sr-AGe model can be used for dose assessment in epidemiological studies of general population exposed to ingested strontium radioisotopes.

age dependence↗

Effect of Helium Flux on Near-surface Helium Accumulation in Plasma-Exposed Tungsten

We report results of object kinetic Monte Carlo (OKMC) simulations aimed at understanding the effect of helium flux on the near-surface helium accumulation in plasma-facing tungsten, which is initially defect-free and has a W(100) surface orientation. These OKMC simulations are performed at 933 K for fluxes ranging from 10 22 to 4 × 10 25 He/m 2 s, with 100 eV helium atoms impinging on a W(100) surface up to a maximum fluence of 4×10 19 He/m 2 . In the near-surface region, helium clusters interact elastically with the free surface. The interaction is attractive and results in the drift of mobile helium clusters towards the surface as well as increased trap mutation rates. The associated kinetics and energetics of the above-mentioned processes obtained from molecular dynamics simulations are also considered. The OKMC simulations indicate that as the flux decreases, the retention of implanted helium decreases, and its depth distribution shifts to deeper below the surface in initially pristine tungsten. Furthermore, the fraction of retained helium diffusing into the bulk increases as well, so much so that for 10 22 He/m 2 s, almost all of the retained helium diffused into the bulk with minimal/negligible near-surface helium accumulation. At a given flux, with increasing fluence, the fraction of retained helium initially decreases and then starts to increase after reaching a minimum. The occurrence of the retention minimum shifts to higher fluences as the flux decreases. Although the near-surface helium accumulation spreads deeper into the material with decreasing flux and increasing fluence, the spread appears to saturate at depths between 80 and 100 nm. Finally, we present a detailed analysis of the influence of helium flux on the size and depth distribution of total helium and helium bubbles.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Mathematical solutions in internal dose assessment: A comparison of Python-based differential equation solvers in biokinetic modeling

Abstract In biokinetic modeling systems employed for radiation protection, biological retention and excretion have been modeled as a series of discretized compartments representing the organs and tissues of the human body. Fractional retention and excretion in these organ and tissue systems have been mathematically governed by a series of coupled first-order ordinary differential equations (ODEs). The coupled ODE systems comprising the biokinetic models are usually stiff due to the severe difference between rapid and slow transfers between compartments. In this study, the capabilities of solving a complex coupled system of ODEs for biokinetic modeling were evaluated by comparing different Python programming language solvers and solving methods with the motivation of establishing a framework that enables multi-level analysis. The stability of the solvers was analyzed to select the best performers for solving the biokinetic problems. A Python-based linear algebraic method was also explored to examine how the numerical methods deviated from an analytical or semi-analytical method. Results demonstrated that customized implicit methods resulted in an enhanced stable solution for the inhaled 60 Co (Type M) and 131 I (Type F) exposure scenarios for the inhalation pathway of the International Commission on Radiological Protection (ICRP) Publication 130 Human Respiratory Tract Model (HRTM). The customized implementation of the Python-based implicit solvers resulted in approximately consistent solutions with the Python-based matrix exponential method ( expm ). The differences generally observed between the implicit solvers and expm are attributable to numerical precision and the order of numerical approximation of the numerical solvers. This study provides the first analysis of a list of Python ODE solvers and methods by comparing their usage for solving biokinetic models using the ICRP Publication 130 HRTM and provides a framework for the selection of the most appropriate ODE solvers and methods in Python language to implement for modeling the distribution of internal radioactivity.

61 RADIATION PROTECTION AND DOSIMETRY↗

Microstructure-dependent rate theory model of defect segregation and phase stability in irradiated polycrystalline LiAlO 2

We report gamma lithium aluminate (LiAlO 2 ) is a breeder material for tritium and is one of key components in a tritium-producing burnable absorber rod (TPBAR). Dissolution and precipitation of second phases such as LiAl 5 O 8 and voids are observed in irradiated LiAlO 2 . Such microstructure changes cause the degradation of thermomechanical properties of LiAlO 2 and affect tritium retention and release kinetics, and hence, the TPBAR performance. In this work, a microstructure-dependent model of radiation-induced segregation (RIS) has been developed for investigating the accumulation of species and phase stability in polycrystalline LiAlO 2 structures under irradiation. Three sublattices (i.e. [Li, Al, V] I [O, V o ] II [Li i , Al i , O i , V i ] III ), and concentrations of six diffusive species (i.e. Li; vacancy of Li or Al at [Li, Al, V] I sublattice, O vacancy at [O, V o ] II sublattice, and Li, Al and O interstitials at [Li i , Al i , O i , V i ] III interstitial sublattices; are used to describe spatial and temporal distributions of defects and chemistry. Microstructure-dependent thermodynamic and kinetic properties including the generation, reaction, and chemical potentials of defects and defect mobility are taken into account in the model. The parametric studies demonstrated the capability of the developed RIS model to assess the effect of thermodynamic and kinetic properties of defects on the segregation and depletion of species in polycrystalline structures and to explain the phase stability observed in irradiated LiAlO 2 samples. The developed RIS model will be extended to study the precipitation of LiAl 5 O 8 and voids and tritium retention by integrating the phase-field method.

36 MATERIALS SCIENCE↗