Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “REACTOR COMPONENTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

Radiation Effects Related to Repaired BWR Core Shrouds

The material properties of the core shroud and supporting tie rod components are important factors for Boiling Water Reactor (BWR) life extension considerations. Given the variability of nickel and boron content found in 304 stainless steel shroud plates, and XM-19 and Inconel X-750 tie rod materials, this paper combines the latest spectral information in the vicinity of the core shroud to calculate hydrogen and helium gas production limits as well as atomic displacement damage spanning 80 full-power years (FPY) using the SPECTER code. Results indicate that, whereas boron has little effect on the atomic displacement damage, helium production from boron can be important and must be included in weldability assessments. Since the boron concentration is uncertain, helium generation is calculated assuming a composition range based on specifications and reported measurements. The results show that helium production caused by transmutations in the 304 SS shroud material are dominated by the concentration of boron and will have a significant impact on weldability after only a few years of service. For tie rods, the susceptibility to irradiation-assisted stress corrosion cracking (IASCC) has been assessed by determining helium production in Inconel X-750 IASCC specimens irradiated in the Advanced Test Reactor (ATR) reactor and correlating with the helium produced in a BWR. As a tie rod material in a high thermal neutron flux environment, Inconel X-750 is more likely to be IASCC sensitive during service in a BWR due to helium than the XM-19 stainless steel alloy because of a greater nickel content and boron concentration. Weldability of the core shroud plate material, IASCC of the tie rod materials, and the gamma photon contribution to radiation damage are discussed.

radiation damage in materials, BWR↗

Microstructure analysis of laser beam weldments performed on neutron-irradiated 304L steel containing 3 and 8 appm helium

We report that AISI 304 L austenitic stainless steel is one of the major structural materials used in light water reactors (LWRs). In the future, 304 L components may require repair, and several welding techniques have been proposed as candidates. In this study, laser beam welding using the low-energy contribution approach was performed in ~2016 on neutron-irradiated AISI 304 L steel with nominal values of 3 and 8 appm helium (He). The goal was to investigate the impact of helium on the irradiated material weldability and evaluate helium-associated damage. The weld and heat-affected zone (HAZ) microstructure was studied using scanning electron microscopy, electron backscatter diffraction, and transmission electron microscopy (TEM). Analysis of the weldment cross-sections did not reveal severe cracking. Still, evidence of incipient helium-associated damage was observed in the HAZ, manifesting as degraded grain boundaries (GBs) “decorated” by pore chains and mostly small (i.e., ≤ 25-30 µm) scattered cracks. The largest observed crack was ~50 µm in length. Helium-associated damage was localized within ~200-300 µm of the weld pool boundary, and the fraction of the compromised GBs, as a rule, was below ~9-11% of the total GB network. TEM analysis showed significant annealing of the radiation-induced defects at distances up to ~300 µm from the weld pool boundary. Inside the HAZ, the cavities (likely, helium bubbles) tended to form at GBs and inclusions, such as manganese sulfide precipitates in the grain interior. Crystallography analysis of the HAZ damage showed that random high-angle boundaries were most susceptible to helium-associated damage. In contrast, low-angle random boundaries and twin boundaries appeared to be strongly resistant to degradation from the combined effects of helium and welding.

36 MATERIALS SCIENCE↗

How irradiation promotes intergranular stress corrosion crack initiation

Irradiation assisted stress corrosion cracking (IASCC) is a form of intergranular stress corrosion cracking that occurs in irradiated austenitic alloys. It requires an irradiated microstructure along with high temperature water and stress. The process is ubiquitous in that it occurs in a wide range of austenitic alloys and water chemistries, but only when the alloy is irradiated. Despite evidence of this degradation mode that dates back to the 1960s, the mechanism by which it occurs has remained elusive. Here, using high resolution electron backscattering detection to analyze local stress-strain states, high resolution transmission electron microscopy to identify grain boundary phases at crack tips, and decoupling the roles of stress and grain boundary oxidation, we are able to unfold the complexities of the phenomenon to reveal the mechanism by which IASCC occurs. The significance of the findings impacts the mechanical integrity of core components of both current and advanced nuclear reactor designs worldwide.

36 MATERIALS SCIENCE↗

Early detection of critical material degradation by means of electromagnetic multi-parametric NDE

With an increasing number of power plants operated in excess of their original design service life an early recognition of critical material degradation in components will gain importance. Many years of reactor safety research allowed for the identification and development of electromagnetic NDE methods which detect precursors of imminent damage with high sensitivity, at elevated temperatures and in a radiation environment. Regarding low-alloy heat-resistant steel grade WB 36 (1.6368, 15NiCuMoNb5), effects of thermal and thermo-mechanical aging on mechanical-technological properties and several micromagnetic parameters have been thoroughly studied. In particular knowledge regarding the process of copper precipitation and its acceleration under thermo-mechanical load has been enhanced. Whilst the Cu-rich WB 36 steel is an excellent model material to study and understand aging effects related to neutron radiation without the challenge of handling radioactive specimens in a hot cell, actually neutron-irradiated reactor pressure vessel materials were investigated as well. The neutron fluence experienced and the resulting shift of the ductile-brittle transition temperature were determined electromagnetically, and it was shown that weld and base material can be distinguished from the cladded side of the RPV wall. Low-cycle fatigue of the austenitic stainless steel AISI 347 (1.4550, X6CrNiNb18-10) has been characterized with electromagnetic acoustic transducers (EMATs) at temperatures of up to 300 °C. Time-of-flight and amplitude of the transmitted ultrasound signal were evaluated against the number of load cycles applied and observed as an indication of the imminent material failure significantly earlier than monitoring stresses or strains.

36 MATERIALS SCIENCE↗

PHENIX U.S.-Japan Collaboration Investigation of Thermal and Mechanical Properties of Thermal Neutron–Shielded Irradiated Tungsten

The United States and Japan have collaborated on fusion materials research in a series of agreements reaching back to 1981. The PHENIX collaboration is the latest U.S.-Japan project which spans 2013 to 2019 and has the goal of assessing technical feasibility of tungsten-based, helium-cooled plasma-facing component concepts for a demonstration fusion power reactor (DEMO). Task 2 within the PHENIX project is focused on evaluating the neutron irradiation effects in tungsten. For tungsten, the transmutation to Re and Os is at least as important to determining its properties after irradiation as the displacement damage, and the transmutation rate depends on the energy spectrum of the reactor. A large-scale, instrumented irradiation capsule with thermal neutron shielding to better mimic fusion conditions was irradiated in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory. The tungsten specimens were irradiated in different temperature zones between 500°C and 1200°C to doses of ~0.2 to 0.7 displacements per atom. More than 20 varieties of pure tungsten and tungsten alloys were included in the irradiation, and they were evaluated in the 3025E hot-cell facility and at the Low Activation Materials Development and Analysis Laboratory. The elevated temperature tensile, fracture toughness, hardness, thermal conductivity, electrical resistivity, density, elemental composition, and microstructure properties of the irradiated materials are being collected. Furthermore, this paper overviews the experimental design, specimen matrix, and the initial results of postirradiation examinations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Verification test suite for systems analysis tools

This report documents strategies and test problems to support Verification and Validation (V&V) of the systems analysis tools currently being developed under the Reactor Product Line (RPL) of DOE’s Nuclear Energy Advanced Modeling and Simulation (NEAMS) program. A suite of verification test cases has been developed. This test suite supports development of new codes as well as maintenance of existing codes. For advanced tools that are under development like RELAP-7 for light water reactor analysis [1] and the MOOSE based component models for SFR (M-SFR) analyses [2], verification of simulation results must be performed throughout the entire development phase. This test suite is also useful for established codes as part of automated testing to ensure that general code maintenance does not change existing results.

Sumner, T.↗

Fabrication Control Plan for ORNL RH-LOCA ATF Test Specimens to be Irradiated in the ATR

The purpose of this fabrication plan is (1) to summarize the design of a set of rodlets that will be fabricated and then irradiated in the Advanced Test Reactor (ATR) and (2) provide requirements for fabrication and acceptance criteria for inspections of the Light Water Reactor (LWR) – Accident Tolerant Fuels (ATF) rodlet components. The functional and operational (F&OR) requirements for the ATF program are identified in the ATF Test Plan. The scope of this document only covers fabrication and inspections of rodlet components detailed in drawings 604496 and 604497. It does not cover the assembly of these items to form a completed test irradiation assembly or the inspection of the final assembly, which will be included in a separate INL final test assembly specification/inspection document. The controls support the requirements that the test irradiations must be performed safely and that subsequent examinations must provide valid results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Catalytic Upgrading of Renewable Feedstock (Final Technical Report)

The goal of this DOE-funded project was to investigate the fundamental science related to the development of homogeneous (de)hydrogenation catalysts in order to enable energy-relevant transformations of bio-relevant chemical feedstocks including ethanol. The primary focus was to improve the activity of ethanol upgrading catalysts, specifically informed through mechanistic studies, in order to enable rational design optimization strategies. Following in depth mechanistic studies, targeted reaction optimization approaches included ligand redesign to improve catalyst stability, developing new carbon-carbon bond forming reactions using ethanol as a precursor, and examining photochemically-mediated reactions, ultimately to integrate within other reactor designs such as continuous flow reactors. The high modularity of the catalyst components (ligands) has enabled the preparation and analyses of multiple catalyst precursors. These studies uncovered an unexpectedly beneficial substitution pattern of the ligand structure that led to the development of new catalysts that are the best in class for upgrading ethanol to butanol with a turnover number of 155,890 and a turnover frequency of 12,690 h –1 . In addition to upgrading ethanol to butanol, cascade reaction sequences were developed to form new C-C bonds using ethanol as a bio-relevant feedstock, providing access to platform chemicals from renewable sources. As part of the reaction discovery process, new mechanistic details were uncovered that provided insights into: a) catalyst speciation, b) decomposition pathways, c) carbon monoxide releasing pathways, and d) carbon-carbon and carbon hydrogen bond breaking pathways. Most of these outcomes were previously not known; however, they provide important directions for new catalyst design strategies. Finally, use of high throughput and in situ photochemical reaction analyses enabled detailed studies into changes to the catalyst structure upon irradiation. Irradiation was found to improve hydrogen transfer catalysis, by promoting a ligand dissociation event.

09 BIOMASS FUELS↗

Summary report describing CASL accomplishments in support of the GTRF Challenge Problem

Coolant flow-induced relative motions between structural components in the cores of lightwater nuclear reactor cores, a phenomenon called Grid-To-Rod Fretting (GTRF), can result in progressive wear damage. Wear-through of the cladding on fuel rods can introduce radioactive species into the coolant loop. Such an event is termed a “leaker” and may cause premature and expensive reactor shut-down. GTRF results in wear scars of various sizes, shapes, and depths on the sides of the fuel rod cladding. Fretting damage may also occur on the springs and dimples that hold the fuel rods in place, resulting in the formation of gaps. Due to variability in the operating conditions of the reactor (burn-up rates and operating campaigns) and the associated variable cladding surface oxide film growth and removal rates, the wear coefficient is unlikely to remain constant over time. Therefore, constant wear rate models do not accurately account for transients in the operating conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

GTRF Cladding Wear Modeling and Experimental Validation

Coolant flow-induced relative motions between certain structural components in the cores of lightwater nuclear reactor cores, a phenomenon called Grid-To-Rod Fretting (GTRF), can result in progressive wear damage. Wear-through of the cladding on fuel rods can introduce radioactive species into the coolant loop. Such an event is termed a “leaker” and may cause premature and expensive reactor shut-down. GTRF results in wear scars of various sizes, shapes, and depths on the sides of the fuel rod cladding. Fretting damage may also occur on the springs and dimples that hold the fuel rods in place, resulting in the formation of gaps. Due to variability in the operating conditions of the reactor (burn-up rates and operating campaigns) and the associated variable cladding surface oxide film growth and removal rates, the wear coefficient is unlikely to remain constant over time. Therefore, constant wear rate models do not accurately account for transients in the operating conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Reduced Models for Chemical Kinetics derived from Parallel Ensemble Simulations of Stirred Reactors

Detailed chemical kinetic models are essential to improve the predictive capability of computational fluid dynamics (CFD) simulations and to impact the development of next generation combustion technologies. However, such detailed kinetic models are beyond the reach of CFD codes due to the computational cost of transporting additional chemical degrees of freedom. Reduced order models for combustion kinetics exploit the presence of lower dimensional manifolds in the state space and require far fewer number of scalars to be transported as part of CFD simulations. In this paper, we describe the software infrastructure developed to allow large ensembles of stirred reactor configurations with detailed chemical kinetics. The canonical reactor simulations are incorporated in a workflow with sparse grid and data reduction methodologies aimed at development of reduced order models. We present results from analyzing the results of the stirred reactor calculations for syngas mixture using principal component analysis (PCA) and neural network methodologies. The results show that nonlinear autoencoder model can surpass PCA in representing the original dataset with far fewer degrees of freedom.

Zhang, Pei↗

Conceptual design study of a six-man solid electrolyte system for oxygen reclamation

A six-man solid electrolyte oxygen regeneration system (SEORS) that will produce 12.5 lbs/day of oxygen has been designed. The SEORS will simultaneously electrolyze both carbon dioxide and water vapor and be suitable for coupling with a carbon dioxide concentration system of either molecular sieve, solid amine or hydrogen depolarized electrochemical type. The total system will occupy approximately 19 cu ft (34.5 in. x .26 in. x 36 in. high) and will weigh approximately 500 pounds. It is estimated that the total electrical power required will be 1783 watts. The system consists of three major components; electrolyzer, hydrogen diffuser, and carbon deposition reactor. There are 108 electrolysis stacks of 12 cells each in the electrolyzer. Only 2/3 of the 108 stacks will be operated at a time; the remainder will be held in reserve. The design calls for 96 palladium membranes for hydrogen removal to give 60 percent redundancy. Four carbon deposition reactors are employed. The iron catalyst tube in each reactor weighs 7.1 lb and 100 percent redundancy is allowed.

Morris, J. P.↗

Study of the collector/heat pipe cooled externally configured thermionic diode

A collector/heat pipe cooled, externally configured (heated) thermionic diode module was designed for use in a laboratory test to demonstrate the applicability of this concept as the fuel element/converter module of an in-core thermionic electric power source. During the course of the program, this module evolved from a simple experimental mock-up into an advanced unit which was more reactor prototypical. Detailed analysis of all diode components led to their engineering design, fabrication, and assembly, with the exception of the collector/heat pipe. While several designs of high power annular wicked heat pipes were fabricated and tested, each exhibited unexpected performance difficulties. It was concluded that the basic cause of these problems was the formation of crud which interfered with the liquid flow in the annular passage of the evaporator region.

Source record↗

Rocketdyne/Westinghouse nuclear thermal rocket engine modeling

The topics are presented in viewgraph form and include the following: systems approach needed for nuclear thermal rocket (NTR) design optimization; generic NTR engine power balance codes; rocketdyne nuclear thermal system code; software capabilities; steady state model; NTR engine optimizer code-logic; reactor power calculation logic; sample multi-component configuration; NTR design code output; generic NTR code at Rocketdyne; Rocketdyne NTR model; and nuclear thermal rocket modeling directions.

Glass, James F.↗

Robot Manipulators

Space Shuttle's Remote Manipulator System (Canadarm) is a 50 foot robot arm used to deploy, retrieve or repair satellites in orbit. Initial spinoff version is designed to remove, inspect and replace large components of Ontario Hydro's CANDU nuclear reactors, which supply 50 percent of Ontario Hydro's total power reduction. CANDU robot is the first of SPAR's Remote Manipulator Systems intended for remote materials handling operations in nuclear servicing, chemical processing, smelting and manufacturing. Inco Limited used remote manipulator for remote control mining equipment to enhance safety and productivity of Inco's hardrock mining operations. System not only improves safety in a hazardous operation that costs more than a score of lives annually, it also increases productivity fourfold. Remote Manipulator System Division is also manufacturing a line of industrial robots and developing additional system for nuclear servicing, mining, defense and space operations.

Source record↗

Reactor Simulator Testing Overview

OBJECTIVE: Integrated testing of the TDU components TESTING SUMMARY: a) Verify the operation of the core simulator, the instrumentation and control system, and the ground support gas and vacuum test equipment. b) Thermal test heat regeneration design aspect of a cold trap purification filter. c) Pump performance test at pump voltages up to 150 V (targeted mass flow rate of 1.75 kg/s was not obtained in the RxSim at the originally constrained voltage of 120 V). TESTING HIGHLIGHTS: a) Gas and vacuum ground support test equipment performed effectively for NaK fill, loop pressurization, and NaK drain operations. b) Instrumentation and control system effectively controlled loop temperature and flow rates or pump voltage to targeted settings. c) Cold trap design was able to obtain the targeted cold temperature of 480 K. An outlet temperature of 636 K was obtained which was lower than the predicted 750 K but 156 K higher than the cold temperature indicating the design provided some heat regeneration. d) ALIP produce a maximum flow rate of 1.53 kg/s at 800 K when operated at 150 V and 53 Hz.

Schoenfeld, Michael P.↗

Recycle of Zirconium from Used Nuclear Fuel Cladding: A Major Element of Waste Reduction

Feasibility tests were initiated to determine if the zirconium in commercial used nuclear fuel (UNF) cladding can be recovered in sufficient purity to permit re-use, and if the recovery process can be operated economically. Initial tests are being performed with unirradiated, non-radioactive samples of various types of Zircaloy materials that are used in UNF cladding to develop the recovery process and determine the degree of purification that can be obtained. Early results indicate that quantitative recovery can be accomplished and product contamination with alloy constituents can be controlled sufficiently to meet purification requirements. Future tests with actual radioactive UNF cladding are planned. The objective of current research is to determine the feasibility of recovery and recycle of zirconium from used fuel cladding wastes. Zircaloy cladding, which contains 98+% of hafnium-free zirconium, is the second largest mass, on average {approx}25 wt %, of the components in used U.S. light-water-reactor fuel assemblies. Therefore, recovery and recycle of the zirconium would enable a large reduction in geologic waste disposal for advanced fuel cycles. Current practice is to compact or grout the cladding waste and store it for subsequent disposal in a geologic repository. This paper describes results of initial tests being performed with unirradiated, non-radioactive samples of various types of Zircaloy materials that are used in UNF cladding to develop the recovery process and determine the degree of purification that can be obtained. Future tests with actual radioactive UNF cladding are planned.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Orientation-Dependent Surface Faceting in UO{sub 2}

The surface behavior of UO{sub 2} plays an important role throughout the lifetime of this widely-used commercial nuclear fuel, from manufacturing to waste storage. UO{sub 2} surface properties affect fuel swelling behavior by determining the morphology, size and distribution of fission gas bubbles. Additionally, UO{sub 2} surface characteristics influence fracture behavior, which is controlled by the thermodynamics of fracture surfaces. Therefore, detailed understanding of the fundamental surface behavior will help advance prediction of the fuel performance of UO{sub 2}. Due to significant anisotropy in surface tension, faceting features form after annealing in both UO{sub 2} and many other crystalline materials. Knowledge of the correlation between crystallographic orientation and surface faceting features will expand the fundamental knowledge of UO{sub 2} surface characteristics, leading to a better understanding of fission gas swelling and fracture mechanisms. Inherent characterization technique limited previous studies on the crystallographic orientation of UO{sub 2} surface facets to low Miller index surfaces in single crystal specimens. In this study, synchrotron Laue microdiffraction was utilized to examine the crystallographic orientation of grains on the coarse surface of a polycrystalline UO{sub 2} specimen. The results were then compared with the surface morphology, obtained from scanning electron microscopy (SEM), so that a general correlation between the surface faceting features and crystallographic orientation in UO{sub 2} can be established. Both the fundamental surface characteristics and the crystallographic orientation measurements obtained in this study help advance the experiment validation of MARMOT, a mesoscale multi-physics code that predicts the coevolution of microstructure and properties within reactor fuel during its lifetime in the reactor. The MARMOT code is an indispensable component of the MOOSE-BISON-MARMOT (MBM) code suite that has been developed by Idaho National Laboratory to enable next generation fuel performance modeling capability as a part of the Nuclear Energy Advanced Modeling and Simulation (NEAMS) Program Fuels Product Line (FPL). In this study, the surface-faceting features of UO{sub 2} were found to be dominated by the triple-plane structure and its variants. With this knowledge, by measuring the directions of the <110> edges, the crystallographic orientation of a surface UO{sub 2} grain can be precisely deduced in most regions of the standard stereogram triangle (SST) of the surface normal. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗