SEARCH · Engineering Papers

Results for “Propellers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

All sources NASA NTRS DOE OSTI

NASA NTRS1980

Fluid dynamics of the unsteady two phase processes leading to DDT in granular solid propellants

Deflagration to Detonation (DDT) was predicted to occur in porous beds of high-energy solid propellants by solving the unsteady fluid mechanical convective heat transfer from hot gas products, obtained from the rapid burning at high pressures, provides the impetus to develop a narrow combustion zone and a resulting strong shock. A parametric study clearly indicates that DDT occurs only when a combination of the solids loading fraction, the burning rate constants, the propellant chemical energy, and the particle size provide for critical energy and gas release to support a detonation wave. Predictions for the run-up length to detonation as a function of these parameters are presented.

Krier, H.↗

NASA NTRS1981

Drive mechanism for the shuttle orbiter/external tank propellant disconnect

The Space Shuttle design required development of a large, 0.43-m (17-in.) nominal diameter separable disconnect for the liquid hydrogen and liquid oxygen propellant lines at the orbiter-to-external-tank interface. The disconnect must provide for shutoff of the propellant flow area by simultaneous action of two rotary flapper valves (orbiter and external tank) prior to disconnect separation. In the case of pneumatic system failure, the rotary flapper valves are closed automatically through mechanical interlocking linkage during disconnect separation. The mechanism must meet requirements while accommodating changes in bearing clearances and linkage geometry over a wide temperature range from ambient to 20.37 K (-423°F). The mechanical design of the separable disconnect, kinematics of the drive mechanism, and the analysis and test methods used to verify proper operation and qualification for the Space Shuttle dynamic environments are presented.

E. Thomas↗

NASA NTRS1981

Measurement of forces due to liquid motion in a propellant tank

This paper presents the results of a study to develop an analytical model capable of predicting the forces acting on a tank caused by large-amplitude propellant motion. This effort contributed to an analysis of the influence of propellant dynamics on separation of the External Tank from the space shuttle orbiter. This paper is concerned with an experimental investigation that aided in development and verification of the analytical model. A scaling approach was developed that allowed the liquid motion to be simulated in subscale tanks. Liquid reorientation forces were measured using two test systems. One operated in the low-gravity environment produced in a drop tower and the second operated aboard the KC-135 'zero-g' test aircraft. The manner of liquid motion, influence of various factors, and the measured forces are discussed.

Tegart, J. R.↗

NASA NTRS1980

A facility for testing the acoustic combustion instability characteristics of solid rocket propellants

A facility is described that has been specifically designed for small-scale laboratory testing of solid rocket propellants. A description of the facility is provided which includes the general plan of the facility and features related to personnel safety. One of the major activities in the facility is testing solid rocket propellants for combustion response to acoustic perturbations. A detailed discussion of acoustic instability testing is given including specially designed combustion apparatus, data acquisition, and signal conditioning. Techniques of data reduction are reviewed and some of the instrumentation problems that arise in this type of testing are mentioned along with practical solutions.

Mathes, H. B.↗

NASA NTRS1981

An improved model for the combustion of AP composite propellants

This paper presents several improvements to the BDP model of steady-state burning of AP composite solid propellants. The Price-Boggs-Derr model of AP monopropellant burning is incorporated to represent the AP. A separate energy equation is written for the binder to permit a different surface temperature from the AP; this includes an analysis of the sharing of primary diffusion flame energy, and correction of a BDP model inconsistency in treating the binder regression rate. A method for assembling component contributions to calculate the burning rates of multimodal propellants is also presented. Results are shown in the form of representative burning rate curves, comparisons with data, and calculated internal details of interest. Ideas for future work are discussed in an Appendix.

Cohen, N. S.↗

NASA NTRS1981

A pocket model for aluminum agglomeration in composite propellants

This paper presents a model for the purpose of estimating the fraction of aluminum powder that will form agglomerates at the surface of deflagrating composite propellants. The basic idea is that the fraction agglomerated depends upon the amount of aluminum that melts within effective binder pocket volumes framed by oxidizer particles. The effective pocket depends upon the ability of ammonium perchlorate modals to encapsulate the aluminum and provide a local temperature sufficient to ignite the aluminum. Model results are discussed in the light of data showing effects of propellant formulation variables and pressure.

Cohen, N. S.↗

NASA NTRS1948

Investigation of Effectiveness of Air-Heating a Hollow Steel Propeller for Protection Against Icing. 2: 50% Impartitioned Blades

The icing protection afforded an internal air-heated propeller blade by radial partitioning at 50-percent chord to confine the heated air to the forward half of the blade was determined in the NACA Cleveland icing research tunnel. A modified production-model hollow steel propeller, was used for the investigation. Temperatures of the blade surfaces for several heating rates were measured under various tunnel Icing' conditions. Photographic observations of ice formations on blade surfaces and blade heat-exchanger effectiveness were obtained. With 50-percent partitioning of the blades, adequate icing protection at 1050 rpm was obtained with a heating rate of 26,000 Btu per hour per blade at the blade shank using an air temperature of 400 F with a flow rate of 280 pounds per hour per blade, which is one-third less heat than was found necessary for similar Ice protection with unpartitioned blades. The chordwise distribution of the applied heat, as determined by surface temperature measurements, was considered unsatisfactory with much of the heat dissipated well back of the leading edge. Heat-exchanger effectiveness of approximately 56 percent also Indicated poor utilization of available heat. This effectiveness was, however, 9 percent greater than that obtained from unpartitioned blades.

Perkins, Porter J.↗

NASA NTRS1953

An Investigation Utilizing an Electrical Analogue of Cyclic Deicing of Hollow Steel Propellers with Internal Electric Heaters

A study has been made of the heating requirements for the cyclic de?icing of hollow steel propellers fitted with two types of internal electric heaters. Solutions to the transient?teat?flow equations depicting the cyclic de?icing of propellers were obtained by use of an electrical analogy. The study showed the impracticability of using an internal tubular heater and illustrated the advantages of employing an internal shoe?type heater, which distributes the heat more evenly to the blade surface. The importance of minimizing the thermal inertia of the system was demonstrated, and the magnitude of reductions in the total energy requirement made possible through reductions in the heating period was indicated.

Neel, Carr B., Jr.↗

NASA NTRS1982

Low-thrust chemical propulsion system propellant expulsion and thermal conditioning study. Executive summary

Preferred techniques for providing abort pressurization and engine feed system net positive suction pressure (NPSP) for low thrust chemical propulsion systems (LTPS) were determined. A representative LTPS vehicle configuration is presented. Analysis tasks include: propellant heating analysis; pressurant requirements for abort propellant dump; and comparative analysis of pressurization techniques and thermal subcoolers.

Merino, F.↗

NASA NTRS1982

Propeller tip vortex - A possible contributor to aircraft cabin noise

Wind tunnel model tests support the hypothesis that a propeller tip vortex may subject a downstream wing surface to greater excitation than would be experienced by the aircraft fuselage side wall exposed to propeller-generated noise, ultimately transmitting this structural response to incident dynamic pressure to the cabin interior. Even if structure-borne excitations are less efficient than airborne excitations in the creation of cabin noise, the higher level of the former could still govern cabin noise levels.

Miller, B. A.↗

NASA NTRS1982

Porous plate analog burner study of composite solid propellant flame structure

A porous plate burner system for studying the structure and interaction of diffusion flames from adjacent unlike sources of oxidizer to simulate the behavior of solid propellant flames is presented. The passage of oxidizer gases through ports of determined diameters represents decomposing oxidizer crystals, and are adjustable for various oxidizer/fuel ratio experiments. Tests with air, ethane, oxygen, and oxygen-air mixtures are described, with parameters of flow rate, oxygen/fuel ratio, and pressure. Coarse ports are found to be oxidizer rich, while fine ports are stoichiometric. More heat feedback is found with fine ports, indicating that fine particle propellant systems burn faster unless fuel allocation is such that the reduced temperature overcomes the reduced diffusion length. Further observations on the interactions of flames are reported.

Strand, L. D.↗

NASA NTRS1981

Technology and benefits of aircraft counter rotation propellers

Results are reported of a NASA sponsored analytical investigation into the merits of advanced counter rotation propellers for Mach 0.80 commercial transport application. Propeller and gearbox performance, acoustics, vibration characteristics, weight, cost and maintenance requirements for a variety of design parameters and special features were considered. Fuel savings in the neighborhood of 8 percent relative to single rotation configurations are feasible through swirl recovery and lighter gearboxes. This is the net gain which includes a 5 percent acoustic treatment weight penalty to offset the broader frequency spectrum noise produced by counter rotation blading.

Strack, W. C.↗

NASA NTRS1983

Analysis and test for space shuttle propellant dynamics

This report presents the results of a study to develop an analytical model capable of predicting the dynamic interaction forces on the Shuttle External Tank, due to large amplitude propellant slosh during RTLS separation. The report details low-g drop tower and KC-135 test programs that were conducted to investigate propellant reorientation during RTLS. In addition, the development of a nonlinear finite element slosh model (LAMPS2, two dimensional, and one LAMPS3, three dimensional) is presented. Correlation between the model and test data is presented as a verification of the modeling approach.

Berry, R. L.↗

NASA NTRS1981

Processing modifications for improved propellants - Coated oxidizers

The present investigation is concerned with a technique which makes it possible to improve greatly the performance of composite propellants by alleviating the combustion instability problem. The technique involves the coating of the oxidizer crystals (typically ammonium perchlorate) with a suitably selected chemical. For each application the chemical for the coating is chosen on the basis of a screening procedure including the employment of differential scanning calorimetry and the use of a thermogravimetric analyzer. It is particularly important that the coat chemicals have good thermochemical stability at temperatures up to the normal surface temperature of the propellant during time-independent combustion (typically 800 to 900 K). At higher temperatures, sudden degradation should occur over a vary narrow temperature range (10-20 C).

Helmy, A. K.↗

NASA NTRS1983

Test program to demonstrate the stability of hydrazine in propellant tanks

The suitability of stainless steels and Inconel for long-term hydrazine propellant-storage tanks is investigated. Rectangular coupon samples cut from propellent tanks were sealed with a measured amount of hydrazine in glass capsules, stored at 43 or 60 C, and removed after 6 to 24 months, when corrosion of the coupon and decomposition of the hydrazine was determined, and SEM and electron spectroscopy were performed on some coupons. Corrosion was found to be unmeasurably low for all the coupons, and hydrazine decomposition produced less than 1.0 cu cm of gas per sq cm of wetted surface per year, except in those few cases when catalysis or contamination were detected. Especially good stability was observed for type 304L stainless steel. The decomposition rates determined in the coupon tests are confirmed by preliminary results of actual tank storage trials.

Moran, C. M.↗

NASA NTRS1982

An experience in mesh generation for three-dimensional calculation of potential flow around a rotating propeller

An attempt is made to develop a three-dimensional, finite volume computational code for highly swept, twisted, small aspect ratio propeller blades with supersonic tip speeds, in a way that accounts for cascade effects, hub-induced flow, and nonlinear transonic effects. Attention is presently given to the generation of a computational mesh for such a complex propeller configuration, with the aim of sharing developmental process experience. The problem treated is unique, in that blade chord, blade length, hub length and blade-to-blade distance represent several characteristic length scales among which there is considerable disparity. An ad hoc mesh-generation scheme is accordingly developed.

Jou, W.-H.↗

NASA NTRS1985

Over-the-Wing Propeller Reduces Wing Drag

Airflow favorably altered if propeller placed above and behind wing. Relocating propeller induces flow over wing airfoil leading edge, which produces leading-edge suction forces not usually attainable by wing in free-stream flow. Concept reduced drag significantly on aircraft model in 12-foot (3.7-meter) wind tunnel. Relocation also helps to reduce cabin noise.

Johnson, J. L., Jr.↗

NASA NTRS1983

A review of in situ propellant production techniques for solar system exploration

Representative studies done in the area of extraterrestrial chemical production as it applies to solar system exploration are presented. A description of the In Situ Propellant Production (ISPP) system is presented. Various propellant combinations and direct applications along with the previously mentioned benefits and liens are discussed. A series of mission scenarios is presented which is studied in the greatest detail. A general description of the method(s) of analysis used to study each mission is provided. Each section will be closed by an assessment of the performance advantage, if any, that can be provided by ISPP. A final section briefly summarizes those missions which, as a result of the studies completed thus far, should see a sizable benefit from the use of ISPP.

Hoffman, S. J.↗