Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Pressure effect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

Effect of vacuum exhaust pressure on the performance of MHD ducts at high B-field

The effect of area ratio variation on the performance of a supersonic Hall MHD duct is investigated. Results indicate that for a given combustion pressure there exists an area ratio below which the power generating region of the duct is shock free and the power output increases linearly with the square of the magnetic field. For area ratios greater than this, a shock forms in the power generating region which moves upstream with increasing magnetic field strength resulting in a less rapid raise in the power output. The shock can be moved downstream by either increasing the combustion pressure of decreasing the exhaust pressure. The influence of these effects upon duct performance is presented.

Smith, J. M.↗

Measuring the effects of pore-pressure changes on seismic amplitude using crosswell continuous active-source seismic monitoring (CASSM)

Monitoring of time-varying reservoir properties, such as the state of stress, is a primary goal of geophysical investigations, including for geological sequestration of CO 2 , enhanced hydrocarbon recovery (EOR), and other subsurface engineering activities. In this work, we used Continuous Active-Source Seismic Monitoring (CASSM), with cross-well geometry, to measure variation in seismic coda amplitude, as a consequence of effective stress change (in the form of changes in pore fluid pressure). To our knowledge, the presented results are the first in-situ example of such crosswell measurement at reservoir scale and in field conditions. Data compliment the findings of our previous work which investigated the relationship between pore fluid pressure and seismic velocity (velocity-stress sensitivity) using the CASSM system at the same field site (Marchesini et al., 2017, in review). We find that P-wave coda amplitude decreases with decreasing pore pressure (increasing effective stress).

58 GEOSCIENCES↗

Air flow and pressure inside a pressure-swirl spray and their effects on spray development

Air flow and pressure inside a pressure-swirl spray for direct injection (DI) gasoline engines and their effects on spray development have been analyzed at different injector operating conditions. A simulation tool was utilized and the static air pressure at the centerline of the spray was measured to investigate the static pressure and flow structure inside the swirl spray. To investigate the effect of static air pressure on swirl spray development, a liquid film model was applied and the Mie-scattered images were captured. The simulation and experiment showed that recirculation vortex and air pressure drop inside the swirl spray were observable and the air pressure drop was greater at high injection pressure. At high fuel temperature, the air pressure at the nozzle exit showed higher value compared to the atmospheric pressure and then continuously decreased up to few millimeters distance from the nozzle exit. The pressure drop at high fuel temperatures was more than that of atmospheric temperature. This reduced air pressure was recovered to the atmospheric pressure at further downstream. The results from the liquid film model and macroscopic spray images showed that the air pressure started to affect the liquid film trajectory about 3 mm from the nozzle exit and this effect was sustained until the air pressure recovered to the atmospheric pressure. However, the entrained air motion and droplet size have more significant influence on the spray development after the most of the liquid sheet is broken-up and the spray loses its initial momentum. (author)

33 ADVANCED PROPULSION SYSTEMS↗

Characteristics of the sub-micron ash aerosol generated during oxy-coal combustion at atmospheric and elevated pressures

This paper is concerned with the effect of pressure on the particle size distribution and the size-segregated composition of the sub-micron ash aerosol created during oxy-coal combustion under near practical self-sustaining combustion conditions. The problem is important because pressurized oxy-coal combustion has been proposed as one promising technology to minimize CO 2 emissions. Sub-micron ash plays a major role in ash deposition mechanisms, which, in turn, can control boiler performance. In this work, the same bituminous coal was burned at pressures of 1, 8 and 15 bar in O 2 /CO 2 environments. Here, tests employed a 100 kW (rated) oxy-fuel combustor (OFC) operated at atmospheric pressure (1 bar) and a 300 kW (rated) entrained-flow pressurized reactor (EFPR) at elevated pressures (8 and 15 bar). Although these tests were conducted under near practical combustion conditions, confounding effects of peak flame temperature variations were minimized for the 1 bar and 15 bar tests, allowing the role of elevated pressure to be isolated. For the EFPR tests, a specially designed sampling system was used to sample sub-micron ash aerosols from the pressurized combustor and is described in detail. Results showed that at the same peak temperature but higher pressure, the fractions of ash aerosol partitioned into the PM 0.6 and PM 1 size fractions were greatly diminished. Moreover, elevated pressures caused significant changes in the composition of the (size-segregated) sub-micron aerosol, especially in its alkali content, which increased significantly. Examination of fractions of each element that ended up in the sub-micron fume suggested that, at constant temperature, the effect of pressure on vaporization of semi-volatile metals was very different from that on the release into the gas phase of non-volatile metals and could not be explained by equilibrium.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Investigation of X24C-2 10-Stage Axial-Flow Compressor: Effect of Inlet-Air Pressure and Temperature of Performance - 2

Effect of inlet-air pressure and temperature on the performance of the X24-2 10-Stage Axial-Flow Compressor from the X24C-2 turbojet engine was evaluated. Speeds of 80, 89, and 100 percent of equivalent design speed with inlet-air pressures of 6 and 12 inches of mercury absolute and inlet-air temperaures of approximately 538 degrees, 459 degrees,and 419 degrees R ( 79 degrees, 0 degrees, and minus 40 degrees F). Results were compared with prior investigations.

Finger, Harold B.↗

Laminar flow in a recess of a hydrostatic bearing

The flow in a recess of a hydrostatic journal bearing is studied in detail. The Navier-Stokes equations for the laminar flow of an incompressible liquid are solved numerically in a two-dimensional plane of a typical bearing recess. Pressure- and shear-induced flows, as well as a combination of these two flow conditions, are analyzed. Recess friction, pressure-ram effects at discontinuities in the flow region, and film entrance pressure loss effects are calculated. Entrance pressure loss coefficients over a forward-facing step are presented as functions of the mean flow Reynolds number for pure-pressure and shear-induced laminar flows.

San Andres, Luis A.↗

Piloted Ignition Delay of PMMA in Space Exploration Atmospheres

In order to reduce the risk of decompression sickness associated with extravehicular activity (EVA), NASA is designing the next generation of exploration vehicles and habitats with a different cabin environment than used previously. The proposed environment uses a total cabin pressure of 52.7 to 58.6 kPa with an oxygen concentration of 30 to 34% by volume and was chosen with material flammability in mind. Because materials may burn differently under these conditions and there is little information on how this new environment affects the flammability of the materials onboard, it is important to conduct material flammability experiments at the intended exploration atmosphere. One method to evaluate material flammability is by its ease of ignition. To this end, piloted ignition delay tests were conducted in the Forced Ignition and Spread Test (FIST) apparatus subject to this new environment. In these tests, polymethylmethacylate (PMMA) was exposed to a range of oxidizer flow velocities and externally applied heat fluxes. Tests were conducted for a baseline case of normal pressure and oxygen concentration, low pressure (58.6 kPa) with normal oxygen (21%), and low pressure with 32% oxygen concentration conditions to determine the individual effect of pressure and the combined effect of pressure and oxygen concentration on the ignition delay. It was found that reducing the pressure while keeping the oxygen concentration at 21% reduced the ignition time by 17% on average. Increasing the oxygen concentration at low pressures reduced the ignition time by an additional 10%. It was also noted that the critical heat flux for ignition decreases at exploration atmospheres. These results show that tests conducted in standard atmospheric conditions will underpredict the ignition of materials intended for use on spacecraft and that, at these conditions, materials are more susceptible to ignition than at current spacecraft atmospheres.

McAllister, Sara↗

Investigation on the solidification of several pure cyclic and aromatic hydrocarbons at pressures to 300 MPa

The effect of pressure on the solidification of several saturated cyclic hydrocarbons and three xylene isomers are experimentally determined with a variable-volume view cell at pressures to 300 MPa and temperatures starting at 293.15 K. Solid–liquid transitions are observed for cyclooctane, cis-1,2-dimethylcyclohexane, trans-1,4-dimethylcyclohexane, p-xylene, o-xylene, and 2-methylnaphthalene. However, methylcyclohexane, ethylcyclohexane, cis-1,4-dimethylcyclohexane, and m-xylene remained liquid over the same operating pressure and temperature ranges. The experimental solid–liquid transition data are well represented with two empirical equations, the Simon equation and a 2nd-order polynomial equation. Data obtained in this study agree with literature data within ±0.4% for 2-methylnaphthalene and ±0.2% for p-xylene.

02 PETROLEUM↗

The preparation of calcium superoxide at subambient temperatures and pressures

The effects of disproportionations at lower temperatures and also of a range of reaction chamber pressures on the preparation of calcium superoxide, Ca(O2)2, from calcium peroxide diperoxyhydrate were studied. About 60% purity of product was obtained by a disproportionation procedure. The significance of features of this procedure for a prospective scale-up of the mass prepared in a single experiment is considered. The optimum pressure for product purity was determined, and the use of a molecular sieve desiccant is described.

Ballou, E. V.↗

Measurement of Activation Volume for Creep of Dry Olivine at Upper-Mantle Conditions

Olivine is the most abundant and among the weakest phases in Earth's upper mantle, and thus, its rheological properties play a critical role in governing thermal structure and convective flow in the upper mantle. A persistent obstacle to constraining the in situ flow properties of olivine by laboratory experiment has been the difficulty in resolving the effect of pressure, which is weak within the 0- to ~2-GPa pressure range of conventional laboratory deformation instruments but potentially strong over the 1- to ~14-GPa range of the upper mantle. Using a deformation-DIA, one of a new generation of bonafide deformation devices designed for operation to ≥10 GPa, we have deformed dry, polycrystalline San Carlos olivine in high-temperature creep with the singular intent of providing the best achievable measurement of activation volume V* and a comprehensive statement of uncertainty. Under strictly dry conditions, at constant temperature (1,373 K) and strain rate (1 × 10 -5 s -1 ), varying only pressure (1.8 to 8.8 GPa), we measure V* = 15 ± 5 cm 3 /mol. We have reproduced the well-known mechanism change from [100]-slip to [001]-slip near 5 GPa and determined that, whatever the change in V* associated with the change in slip system, the effective value of 15 ± 5 cm3/mol is still accurate for modeling purposes in the 2- to 9-GPa pressure range. This is a substantial pressure effect, which in the absence of a temperature gradient would represent a viscosity increase from the top to bottom of the upper mantle of 5 ± 2 orders of magnitude.

58 GEOSCIENCES↗

Combined pressure and temperature distortion effects on internal flow of a turbofan engine

An additional data base for improving and verifying a computer simulation developed by an engine manufacturer was obtained. The multisegment parallel compressor simulation was designed to predict the effects of steady-state circumferential inlet total-pressure and total-temperature distortions on the flows into and through a turbofan compression system. It also predicts the degree of distortion that will result in surge of the compressor. The effect of combined 180 deg square-wave distortion patterns of total pressure and total temperature in various relative positions is reported. The observed effects of the combined distortion on a unitary bypass ratio turbofan engine are presented in terms of total and static pressure profiles and total temperature profiles at stations ahead of the inlet guide vanes as well as through the fan-compressor system. These observed profiles are compared with those predicted by the complex multisegment model. The effects of relative position of the two components comprising the combined distortion on the degree resulting in surge are discussed. Certain relative positions required less combined distortion than either a temperature or pressure distortion by itself.

Braithwaite, W. M.↗

Stabilizing Effect of High Pore Fluid Pressure on Slip Behaviors of Gouge-bearing Faults

We conducted experiments to investigate the influence of pore fluid pressure on the frictional strength and slip behavior of gouge bearing faults. Saw cut porous sandstone samples with a layer of gouge powders placed between the precut surfaces were deformed in the conventional triaxial loading configuration. A series of velocity-step tests were performed to measure the response of the friction coefficient to variations in sliding velocity. Pore volume changes were monitored during shearing of the gouge. Our results demonstrate that under constant effective pressure, increasing pore pressure stabilizes the frictional slip of faults with all four gouge materials including antigorite, olivine, quartz, and chrysotile. The stabilizing effect is the strongest in antigorite gouge, which shows an evolution of friction parameters from velocity-weakening toward velocity-strengthening behavior with increasing pore pressure. Experiments with controlled pore volume show that the pore volume reduction diminishes under high pore fluid pressures, implying an increasing dilation component at these conditions. The dilatant hardening mechanism can explain the observed strengthening. These results provide a possible explanation to the observed spatial correlation between slow slip events and high pore pressure in many subduction zones.

58 GEOSCIENCES↗