Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PLASMA ENGINE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

Initial transient stage of pin-to-pin nanosecond repetitively pulsed discharges in air

In this work, evolution of parameters of nanosecond repetitively pulsed (NRP) discharges in pin-to-pin configuration in air was studied during the transient stage of initial 20 discharge pulses. Gas and plasma parameters in the discharge gap were measured using coherent microwave scattering, optical emission spectroscopy, and laser Rayleigh scattering for NRP discharges at repetition frequencies of 1, 10, and 100 kHz. Memory effects (when perturbations induced by the previous discharge pulse would not decay fully until the subsequent pulse) were detected for the repetition frequencies of 10 and 100 kHz. For 10 kHz NRP discharge, the discharge parameters experienced significant change after the first pulse and continued to substantially fluctuate between subsequent pulses due to rapid evolution of gas density and temperature during the 100 μs inter-pulse time caused by intense redistribution of the flow field in the gap on that time scale. For 100 kHz NRP discharge, the discharge pulse parameters reached a new steady-state at about five pulses after initiation. Further, this new steady-state was associated with well-reproducible parameters between the discharge pulses and substantial reduction in breakdown voltage, discharge pulse energy, and electron number density in comparison to the first discharge pulse. For repetition frequencies 1–100 kHz considered in this work, the memory effects can be likely attributed to the reduction in gas number density and increase in the gas temperature that cannot fully recover to ambient conditions before subsequent discharge pulses.

42 ENGINEERING↗

Plasma-free atomic layer deposition of Ru thin films using H{sub 2} molecules as a nonoxidizing reactant

The ruthenium (Ru) thin films were grown by atomic layer deposition (ALD) using a sequential supply of dicarbonyl-bis(5-methyl-2,4-hexanediketonato) Ru(II) (C{sub 16}H{sub 22}O{sub 6}Ru) and H{sub 2} as a reactant at a substrate temperature of 250 °C. Deposition was possible using H{sub 2} molecules without a plasma by increasing the chamber pressure to above 10 Torr. Specifically, high-quality Ru films with a low resistivity of ∼40 μΩ cm and few amount of oxygen (∼1.2 at. %) were obtained under a chamber pressure of 300 Torr though the oxygen was contained in the precursor. Under the optimized conditions, self-limited film growth with regard to the precursor and reactant pulsing times was confirmed under elevated chamber pressures. The ALD-Ru process proposed in this study showed one of the highest growth rates of 0.12 nm/cycle on a thermally grown SiO{sub 2} substrate, as well as a very low number of incubation cycles (approximately 12 cycles). Cross-sectional view transmission electron microscopy showed that no interfacial oxide had formed during the deposition of the ALD-Ru films on a W surface using H{sub 2} molecules, whereas ∼7 nm thick interfacial oxide was formed when O{sub 2} molecules were used as a reactant. The step coverage of the ALD-Ru film onto very small-sized trenches (aspect ratio: ∼4.5 and the top opening size of 25 nm) and holes (aspect ratio: ∼40 and top opening size of 40 nm) was excellent (∼100%).

36 MATERIALS SCIENCE↗

Damage Accumulation and Failure of Plasma-Sprayed Thermal Barrier Coatings under Thermal Gradient Cyclic Conditions

Thermal barrier coatings will be more aggressively designed to protect gas turbine engine hot-section components in order to meet future engine higher fuel efficiency and lower emission goals. A fundamental understanding of the sintering and thermal cycling induced delamination of thermal barrier coating systems under engine-like heat flux conditions will potentially help to improve the coating temperature capability. In this study, a test approach is established to emphasize the real-time monitoring and assessment of the coating thermal conductivity, which can initially increase under the steady-state high temperature thermal gradient test due to coating sintering, and later decrease under the thermal gradient cyclic test due to coating cracking and delamination. Thermal conductivity prediction models have been established for a ZrO2-(7- 8wt%)Y2O3 model coating system in terms of heat flux, time, and testing temperatures. The coating delamination accumulation is then assessed based on the observed thermal conductivity response under the combined steady-state and cyclic thermal gradient tests. The coating thermal gradient cycling associated delaminations and failure mechanisms under simulated engine heat-flux conditions will be discussed in conjunction with the coating sintering and fracture testing results.

Zhu, Dongming↗

Design and Engineering of LUPIN: A Test-Bed Radiofrequency Ion Source for Enhanced Neutral Beam Injection on DIII-D

The Large, Uniform Plasma for Ionizing Neutrals (LUPIN) is an RF inductively coupled plasma (ICP) chamber for demonstrating plasma performance of an RF ICP positive ion source upgrade for the DIII-D Neutral Beam Injection (NBI) system. LUPIN will be used to investigate ion source physics, including neutral gas dynamics, plasma density uniformity, interactions with Faraday shields, and power coupling to novel RF antenna designs. LUPIN has an RF generator capable of delivering 20 kW of power at 2 MHz, which is coupled into a cylindrical quartz vessel measuring 20 cm in length and 10 cm in radius. This configuration matches the power density requirements for a full-scale ion source. Target hydrogen and deuterium plasma densities exceeding 10 18 m -3 would relate to extracted ion current densities of 2100 A/m 2 for 10 s. Vacuum conductance and gas flow calculations predict a maximum achievable neutral gas flow rate of 1675 Pa·L/s at 5 Pa of He, which mimics the gas flow of the DIII-D NBI system. Designs have been developed for an internal Faraday shield to mitigate heat flux and ion sputtering on the dielectric vessel. Thermomechanical finite element simulations demonstrated the Faraday shield design to be capable of withstanding anticipated heat loads from worst-case operation scenarios. Results of upcoming experimental investigations on LUPIN will guide the design of a full-scale prototype for DIII-D integration.

Faraday shield↗

Fabrication and Characterization of Non-Equilibrium Plasma-Treated PVDF Nanofiber Membrane-Based Sensors

The effect of a self-pulsing non-equilibrium plasma discharge on piezoelectric PVDF nanofiber membrane was investigated. The plasma discharge was generated in air with a DC power source, with a discharge current of 0.012 mA, a nominal interelectrode separation of 1 mm, and discharge voltage of ~970 V. In a continuous fabrication process, the electrospinning method was used to generate thin nanofiber membrane with a flow rate of 0.7–1 mL h -1 and 25–27 kV voltage to obtain the nanofiber with high sensitivity and a higher degree of alignment and uniformity over a larger area. Plasma treatment was applied on both single layer and multi-layer (three layers) nanomembranes. In addition, simultaneously, the nanofiber membranes were heat-treated at a glass transition temperature (80–120 °C) and then underwent plasma treatment. Fourier-transform infrared (FTIR) spectroscopy showed that the area under the curve at 840 and 1272 cm -1 (β phase) increased due to the application of plasma and differential scanning calorimeter (DSC) indicated an increase in the degree of crystallinity. Finally, PVDF sensors were fabricated from the nanofibers and their piezoelectric properties were characterized. The results suggested that compared to the pristine samples the piezoelectric properties in the plasma and plasma-heat-treated sensors were enhanced by 70% and 85% respectively.

42 ENGINEERING↗

Surface cleaning for enhanced adhesion to packaging surfaces: Effect of oxygen and ammonia plasma

The effects of direct plasma chemistries on carbon removal from silicon nitride (SiN{sub x}) and oxynitride (SiO{sub x}N{sub y}) surfaces have been studied by in-situ x-ray photoelectron spectroscopy (XPS) and ex-situ contact angle measurements. The data indicate that O{sub 2} and NH{sub 3} capacitively coupled plasmas are effective at removing adventitious carbon from silicon nitride (SiN{sub x}) and Si oxynitride (SiO{sub x}N{sub y}) surfaces. O{sub 2} plasma treatment results in the formation of a silica overlayer. In contrast, the exposure to NH{sub 3} plasma results in negligible additional oxidation of the SiN{sub x} or SiO{sub x}N{sub y} surface. Ex-situ contact angle measurements show that SiN{sub x} and SiO{sub x}N{sub y} surfaces exposed to oxygen plasma are initially more hydrophilic than surfaces exposed to NH{sub 3} plasma, indicating that the O{sub 2} plasma-induced SiO{sub 2} overlayer is highly reactive toward ambient. At longer ambient exposures (≳10 h), however, surfaces treated by either O{sub 2} or NH{sub 3} plasma exhibit similar steady state contact angles, correlated with rapid uptake of adventitious carbon, as determined by XPS. Surface passivation by exposure to molecular hydrogen prior to ambient exposure significantly retards the increase in contact angle upon exposure to ambient. The results suggest a practical route to enhancing the time available for effective bonding to surfaces in microelectronics packaging applications.

36 MATERIALS SCIENCE↗

Comparison of CF4 and SF6 based plasmas for ECR etching of isotopically enriched 10Boron films

Isotopically enriched {sup 10}boron films have been successfully etched in an ECR etching tool using CF{sub 4} and SF{sub 6} based plasmas. Comparisons between the two are made with regards to etch rate, selectivity to the underlying Si device structure, and morphology of the {sup 10}boron post-etching. The present film etching development is expected to be critical for the fabrication of next generation thermal neutron solid state detectors based on {sup 10}boron.

42 ENGINEERING↗

Bremsstrahlung and Line Spectroscopy of Warm Dense Aluminum Plasma Generated by EUV Free Electron Laser

We report on the novel creation of a solid density aluminum plasma using free electron laser radiation at 13.5 nm wavelength. Ultrashort pulses of 30 fs duration and 47 {micro}J pulse energy were focused on a spot of 25 {micro}m diameter, yielding an intensity of 3 x 10{sup 14} W/cm{sup 2} on the bulk Al-target. The radiation emitted from the plasma was measured using a high resolution, high throughput EUV spectrometer. The analysis of both bremsstrahlung and line spectra results in an estimated electron temperature of (30 {+-} 10) eV, which is in very good agreement with radiation hydrodynamics simulations of the laser-target-interaction. This demonstrates the feasibility of exciting plasmas at warm dense matter conditions using EUV free electron lasers and their accurate characterization by EUV spectroscopy.

42 ENGINEERING↗

Plasma generation near an Ion thruster disharge chamber hollow cathode

In gridded electrostatic thrusters, ions are produced by electron bombardment in the discharge chamber. In most of these thrusters, a single, centrally located hollow cathode supplies the ionizing electrons. An applied magnetic field in the discharge chamber restricts the electrons leaving the hollow cathode to a very narrow channel. In this channel, the high electron current density ionizes both propellant gas flowing from the hollow cathode, and other neutrals from the main propellant flow from the plenum. The processes that occur just past the hollow cathode exit are very important. In recent engine tests, several cases of discharge cathode orifice place and keeper erosion have been reported. In this paper we present results from a new 1-D, variable area model of the plasma processes in the magnetized channel just downstream of the hollow cathode keeper. The model predicts plasma densities, and temperatures consistent with those reported in the literature for the NSTAR engine, and preliminary results from the model show a potential maximum just downstream of the cathode.

cathode↗

Development of Advanced Low Conductivity Thermal Barrier Coatings

Advanced multi-component, low conductivity oxide thermal barrier coatings have been developed using an approach that emphasizes real-time monitoring of thermal conductivity under conditions that are engine-like in terms of temperatures and heat fluxes. This is in contrast to the traditional approach where coatings are initially optimized in terms of furnace and burner rig durability with subsequent measurement in the as-processed or furnace-sintered condition. The present work establishes a laser high-heat-flux test as the basis for evaluating advanced plasma-sprayed and electron beam-physical vapor deposited (EB-PVD) thermal barrier coatings under the NASA Ultra-Efficient Engine Technology (UEET) Program. The candidate coating materials for this program are novel thermal barrier coatings that are found to have significantly reduced thermal conductivities and improved thermal stability due to an oxide-defect-cluster design. Critical issues for designing advanced low conductivity coatings with improved coating durability are also discussed.

Zhu, Dong-Ming↗

Event Plane Dependence of Di-hadron Correlations with Event Shape Engineering at the STAR Experiment

In high-energy nuclear collisions, di-hadron correlations are used as a probe to study energy-loss mechanisms of jets in the Quark-Gluon Plasma (QGP). In order to understand the interplay between jet-medium interaction and medium expansion, we measured di-hadron correlations where events were classified by the trigger-hadron’s angle with respect to the event plane. We further constrained the collision geometry using event-shape engineering based on the magnitude of the reduced flow vector q 2 . This measurement provides new and unique constraints for the dependence of energy loss of jets on in-medium path length and the role of flow.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

The Radiation Safety Information Computational Center (RSICC): A Resource for Nuclear Science Applications

The Radiation Safety Information Computational Center (RSICC) has been in existence since 1963. RSICC collects, organizes, evaluates and disseminates technical information (software and nuclear data) involving the transport of neutral and charged particle radiation, and shielding and protection from the radiation associated with: nuclear weapons and materials, fission and fusion reactors, outer space, accelerators, medical facilities, and nuclear waste management. RSICC serves over 12,000 scientists and engineers from about 100 countries. An important activity of RSICC is its participation in international efforts on computational and experimental benchmarks. An example is the Shielding Integral Benchmarks Archival Database (SINBAD), which includes shielding benchmarks for fission, fusion and accelerators. RSICC is funded by the United States Department of Energy, Department of Homeland Security and Nuclear Regulatory Commission.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Tritium permeability measurement in hydrogen-tritium system

Fusion power promises to provide electricity generation with outstanding safety and environmental performance. Safety plays a crucial role in fusion material selection since tritium behavior in materials determines two key safety evaluation source terms: in-vessel inventory source term and ex-vessel release term, which are used in reactor safety assessments for licensing fusion facilities. Tritium permeation through materials at elevated temperature during long pulse operation expected in a burning plasma environment will become a major safety issue and development of tritium permeation barrier materials is required to minimize ex-vessel release to the environment [1]. Extensive work on hydrogen and deuterium behavior in fusion materials has been conducted, but very little database is available for tritium, the radioactive fuel for future reactors, due to the cost and difficulty associated with handling tritium [2]. A majority of the experiments were carried out at high hydrogen/deuterium partial pressure (> 100 Pa), but the expected tritium partial pressure in the blanket system is at low tritium partial pressure (< 100 Pa), where the tritium behavior deviates from diffusion-limited to surface-limited permeation. At these pressures the behavior of tritium is suspected to deviate from diffusion-limited to surface-limited permeation or isotope-limited [3]. The use of tritium enables us to investigate hydrogen isotope behavior in low partial pressure range with beta radiation detection. The physics of two-component hydrogen (H+T) permeation through metal in the surface-limited regime and through liquid breeding material are still too poorly understood to confidently design environmentally benign and safe fusion systems. In this paper, we discuss development of tritium permeation system for low tritium partial pressure [4], and discuss the results from two-component hydrogen (H+T) permeation in 20 mm disc samples of pure alpha-iron at H2 partial pressure of 100 Pa, wide T2 partial pressure range from 10-12 to 10 Pa, and sample temperature up to 600 °C to uncover the basic scientific understanding of tritium permeation behavior at realistic blanket conditions for DEMO. [1] FESAC report on “Opportunities for Fusion Materials Science and Technology Research Now and During the ITER Era” (2012) DOE/SC-0149 [2] R.A. Causey, R.A. Karnesky, and C. San Marchi, “4.16 Tritium Barriers and Tritium Diffusion in Fusion Reactors”, Comprehensive Nuclear Materials (2012) Chapter 4.16. [3] P. Humrickhouse “Permeation of Tritium and Hydrogen in the Diffusion-Limited and Surface–Limited Regimes”, submitted to Journal of Nuclear Materials. [4] R.J. Pawelko, M. Shimada, K. Katayama, S. Fukada, P.W. Humrickhouse, and T. Terai, “Low tritium partial pressure permeation system for mass transport measurement in lead lithium eutectic”, Fusion Engineering and Design 102 (2016) 8

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The Dawn of a New Era for High Energy Density Physics

The field of High Energy Density (HED) physics is on the verge of a revolutionary event - the achievement of fusion ignition in the laboratory. New laser facilities, the OMEGA Extended Performance (EP) laser at the University of Rochester and the National Ignition Facility (NIF) at Lawrence Livermore National Laboratory, greatly extend the range of high energy density (HED) plasma conditions (including ignition) accessible in the laboratory. These conditions are among the most extreme obtainable, with pressures in excess of {approx}1,000,000 atmospheres. Experiments at these facilities will elucidate fundamental new science in astrophysics, materials science, laser-matter interactions, and other areas. The demonstration of fusion ignition will be the culmination of decades of research, and for the first time, will open the burning plasma regime to laboratory exploration. Ignition will spur the development of advanced options for clean, environmentally sustainable energy.

42 ENGINEERING↗

Demonstration of improved dilution tolerance using a production-intent compact nanosecond pulse ignition system

Transient plasma ignition using nanosecond pulses has demonstrated the potential to enable improved fuel economy and reduced emissions by enabling lean and EGR limit extension in dilute burn engines. Existing spark ignition technology is not adequate because the energy transfer mechanisms between the spark and the fuel-air mixture are not efficient enough to guarantee stable ignition for dilute mixtures at high-load conditions. Additionally, long duration sparks and other advanced ignition solutions that require increased energy delivered accelerate spark plug electrode wear. To date, non-thermal plasma ignition with nanosecond pulses have demonstrated a lean ignition limit beyond an air/fuel ratio of 24 [1], demonstrated high-pressure ignition at densities equivalent to over 100 bar at the time of ignition [2], and demonstrated stable (COV <3 %) ignition at EGR dilution levels >20 % [3]. While low-energy nanosecond pulses have demonstrated strong performance compared to existing solutions, they currently only exist on the market in laboratory systems, rather than a production ready system in a single rugged, weather-proof, under-the-hood enclosure. Transient Plasma Systems (TPS) has recently demonstrated the potential for a retroffitable solution similar to coil-on-plug architecture that allows a direct replacement of existing ignition technology without any engine modification. The system was run on a gasoline direct injection engine at Argonne National Laboratory and demonstrated the same trends as previously observed with research grade systems, including lean and EGR limit extension and more stable ignition across a range of loads. The system was capable of delivering 30 kV pulses in bursts of up to 20 pulses at 30 kHz, and demonstrated stable combustion at an air/fuel ratio of 23.5, exhaust gas recirculation of 23 %, and ignition at 19.2 bar with COV <3 % using only 20 kV pulses.

nanosecond pulsed power↗