Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PHOTOELECTRICITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,297 records · Page 72

GaN photovoltaic leakage current and correlation to grain size

GaN p-i-n solar PV structures grown by rf plasma assisted molecular beam epitaxy (MBE) produce high performance IV characteristics with a leakage current density of less than 1x10{sup -4} mA cm{sup -2} at 0.1 V forward bias and an on-resistance of 0.039 {Omega} cm{sup 2}. Leakage current measurements taken for different size diodes processed on the same sample containing the solar cells reveal that current density increases with diode area, indicating that leakage is not a large function of surface leakage along the mesa. Nonannealed Pt/Au Ohmic p-contacts produce a contact resistivity of 4.91x10{sup -4} {Omega} cm{sup -2} for thin Mg doped contact layers with sheet resistivity of 62196 {Omega}/{open_square}. Under concentrated sunlight the cells produce an open-circuit voltage of 2.5 V and short circuit currents as high as 30 mA cm{sup -2}. Multiple growths comprised the study and on each wafer the IV curves representing several diodes showed considerable variation in parasitic leakage current density at low voltages on some wafers and practically no variation on others. It appears that a smaller grain size within the GaN thin film accounts for higher levels of dark current.

36 MATERIALS SCIENCE↗

Light absorption and electrical transport in Si:O alloys for photovoltaics

Thin films (100-500 nm) of the Si:O alloy have been systematically characterized in the optical absorption and electrical transport behavior, by varying the Si content from 43 up to 100 at. %. Magnetron sputtering or plasma enhanced chemical vapor deposition have been used for the Si:O alloy deposition, followed by annealing up to 1250 deg. C. Boron implantation (30 keV, 3-30x10{sup 14} B/cm{sup 2}) on selected samples was performed to vary the electrical sheet resistance measured by the four-point collinear probe method. Transmittance and reflectance spectra have been extracted and combined to estimate the absorption spectra and the optical band gap, by means of the Tauc analysis. Raman spectroscopy was also employed to follow the amorphous-crystalline (a-c) transition of the Si domains contained in the Si:O films. The optical absorption and the electrical transport of Si:O films can be continuously and independently modulated by acting on different parameters. The light absorption increases (by one decade) with the Si content in the 43-100 at. % range, determining an optical band gap which can be continuously modulated into the 2.6-1.6 eV range, respectively. The a-c phase transition in Si:O films, causing a significant reduction in the absorption coefficient, occurs at increasing temperatures (from 600 to 1100 deg. C) as the Si content decreases. The electrical resistivity of Si:O films can be varied among five decades, being essentially dominated by the number of Si grains and by the doping. Si:O alloys with Si content in the 60-90 at. % range (named oxygen rich silicon films), are proved to join an appealing optical gap with a viable conductivity, being a good candidate for increasing the conversion efficiency of thin-film photovoltaic cell.

36 MATERIALS SCIENCE↗

New Packing Structure of Concentration Solar Receiver

This paper presents a solution to the temperature issue in High Concentration Photovoltaic (HCPV) module device by using different thermal conductive material and packing structure. In general, the open-circuited voltage of a device reduces with the increase of temperature and therefore degrades its efficiency. The thermal conductive material we use in this paper, silicon, has a high thermal conductive coefficient (149 W/m{center_dot}K) and steady semiconductor properties which are suitable for the application of solar receiver in HCPV module. Solar cell was soldered on a metal-plated Si substrate with a thicker SiO{sub 2} film which acts as an insulating layer. Then it was mounted on an Al-based plate to obtain a better heat dissipating result.

36 MATERIALS SCIENCE↗

Liquid crystal-ZnO nanoparticle photovoltaics: Role of nanoparticles in ordering the liquid crystal

We investigate the role that order plays in the transfer of charges in the ZnO nano-particle-octylcyanobiphenyl (8CB) liquid crystal system, considered for photovoltaic applications. We have changed the concentration of ZnO nanoparticles in 8CB from 1.18 to 40 wt %. Our results show an improvement in the alignment of the liquid crystal with increasing weight percentage of ZnO nanoparticles, up to a concentration of 30 wt %. In addition, the current generated by the system increases by three orders of magnitude.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The Dependence of Donor:Acceptor Ratio on the Photovoltaic Performances of Blended poly (3-octylthiophene-2,5-diyl) and (6,6)-phenyl C{sub 71} butyric acid methyl ester Bulk Heterojunction Organic Solar Cells

Bulk heterojunction organic solar cells using blended poly (3-octylthiophene-2,5-diyl)(P3OT) and (6,6)-phenyl C{sub 71} butyric acid methyl ester (PC{sub 71}BM) have been fabricated. P3OT and PC{sub 71}BM were used as the electron donor (D) and acceptor (A), respectively. Both materials were mixed and dissolved in dichlorobenzene with three different D:A ratios i.e. 1:3, 1:1 and 3:1 (weight) while maintained at the concentration of 2 wt%(26 mg/ml). The blended thin films were sandwiched between the indium tin oxide (ITO) coated glass and the aluminum film. This paper reports the influence of donor:acceptor ratio on the performance of solar cell devices measured by current-voltage measurement both in the dark and under 1.5 AM solar illumination. It was found that all devices showed the photovoltaic effect with poor diode behavior and the donor:acceptor ratio significantly influenced on the performance of bulk heterojunction organic solar cells.

36 MATERIALS SCIENCE↗

Organic Thin-Film Solar Cells Based on Donor-Acceptor Interpenetrating Nano-Interface

Photovoltaic cells with interpenetrating interfaces between a conducting polymer layer and a fullerene layer fabricated by a solvent corrosion method have been investigated. Using a weakly dissoluble combination of a solvent and an underlayer film, we fabricated a ''semi-layered'' structure that was maintaining a bilayer structure and furthermore interpenetrating at the interface of the conducting polymer and the fullerene layers. In these cells, high external quantum efficiencies (EQE) were obtained. The photovoltaic properties have been interpreted by the effective absorption of incident photons around the interface of conducting polymer and fullerene, the interpenetrating fullerene / conducting polymer interface involving the efficient photo-induced charge transfer, and the short distance between the electron-generation region and electrode resulting in the enhancement of the electron collection to the electrode. In these cells, both of the efficient exciton dissociations at the interpenetrating interface and the efficient carrier transports by each continuous pathway for electrons between fullerene molecules and for holes between conducting polymers occur.

36 MATERIALS SCIENCE↗

Shockley-Read-Hall recombination in P3HT:PCBM solar cells as observed under ultralow light intensities

We present light intensity dependent measurements of the quantum efficiency of P3HT:PCBM photovoltaic devices. Unlike previous studies we focus on ultralow light intensities down to 10{sup -3} mW/cm{sup 2}. We find that although when the devices are excited at intensities close to 1 Sun they exhibit very little bias or light intensity dependence, this is clearly not the case for light intensities below 1 mW/cm{sup 2}, where the cell's efficiency becomes highly dependent on the bias and light intensity. Using a simple model for the device efficiency we can fit the experimental data across a wide range of parameters and thus separate the effects of generation efficiency (geminate recombination) and charge recombination. Our finding suggests that recombination through trap (charge transfer) states is an important loss mechanism and we are able to quantify the density and depth of these states.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Method For Silicon Surface Texturing Using Ion Implantation

As the semiconductor industry continues to show more interest in the photovoltaic market, cheaper and readily integrable methods of silicon solar cell production are desired. One of these methods - ion implantation - is well-developed and optimized in all commercial semiconductor fabrication facilities. Here we have developed a silicon surface texturing technique predicated upon the phenomenon of surface blistering of H-implanted silicon, using only ion implantation and thermal annealing. We find that following the H implant with a second, heavier implant markedly enhances the surface blistering, causing large trenches that act as a surface texturing of c-Si. We have found that this method reduces total broadband Si reflectance from 35% to below 5percent;. In addition, we have used Rutherford backscattering/channeling measurements investigate the effect of ion implantation on the crystallinity of the sample. The data suggests that implantation-induced lattice damage is recovered upon annealing, reproducing the original monocrystalline structure in the previously amorphized region, while at the same time retaining the textured surface.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Solution processable organic polymers and small molecules for bulk-heterojunction solar cells: A review

Solution processed bulk heterojunction (BHJ) organic solar cells (OSCs) have gained wide interest in past few years and are established as one of the leading next generation photovoltaic technologies for low cost power production. Power conversion efficiencies up to 6% and 6.5% have been reported in the literature for single layer and tandem solar cells, respectively using conjugated polymers. A recent record efficiency about 8.13% with active area of 1.13 cm{sup 2} has been reported. However Solution processable small molecules have been widely applied for photovoltaic (PV) devices in recent years because they show strong absorption properties, and they can be easily purified and deposited onto flexible substrates at low cost. Introducing different donor and acceptor groups to construct donor--acceptor (D--A) structure small molecules has proved to be an efficient way to improve the properties of organic solar cells (OSCs). The power conversion efficiency about 4.4 % has been reported for OSCs based on the small molecules. This review deals with the recent progress of solution processable D--A structure small molecules and discusses the key factors affecting the properties of OSCs based on D--A structure small molecules: sunlight absorption, charge transport and the energy level of the molecules.

14 SOLAR ENERGY↗

Bilayer Polymer Solar Cells with Improved Power Conversion Efficiency and Enhanced Spectrum Coverage

We demonstrate the construction of an efficient bilayer polymer solar cell comprising of Poly(3-hexylthiophene)(P3HT) as a p-type semiconductor and asymmetric fullerene (C{sub 70}) as n-type counterparts. The bilayer configuration was very efficient compared to the individual layer performance and it behaved like a regular p-n junction device. The photovoltaic characteristic of the bilayers were studied under AM 1.5 solar radiation and the optimized device parameters are the following: Voc = 0.5V, Jsc = 10.1 mA/cm{sup 2}, FF = 0.60 and power conversion efficiency of 3.6 %. A high fill factor of {approx}0.6 was achieved, which is only slightly reduced at very intense illumination. Balanced mobility between p-and n-layers is achieved which is essential for achieving high device performance. Correlation between the crystallinity, morphology and the transport properties of the active layers is established. The External quantum efficiency (EQE) spectral distribution of the bilayer devices with different processing solvents correlates well with the trends of short circuit current densities (J{sub sc}) measured under illumination. Efficiency of the bilayer devices with rough P3HT layer was found to be about 3 times higher than those with a planar P3HT surface. Hence it is desirable to have a larger grains with a rough surface of P3HT layer for providing larger interfacial area for the exciton dissociation.

14 SOLAR ENERGY↗

Effect of Sputtering Gas environments on the Properties of Aluminum-doped Zinc Oxide Thin Films for Photovoltaic Application

Aluminum-doped zinc oxide thin films have been deposited on glass substrates by R.F. sputtering using ZnO(98%)-Al{sub 2}O{sub 3}(2%) target in different sputtering gaseous environments, viz., Ar, Ar/O{sub 2} and Ar/N{sub 2}+H{sub 2} at 80 deg. C. These films have been studied with regard to phase, microstructure, optical absorption and sheet resistance for application in photovoltaic devices as transparent conducting electrodes. The properties of the films are shown to strongly depend on the sputtering gas(es). The films exhibit a wurtzite-type hexagonal structure with the (00.2) preferred orientation, the c-axis perpendicular to the substrate. The intensity of 00.2 diffraction peak and the average crystallite size remain almost the same when the films are prepared under pure Ar or Ar/O{sub 2} environment. However the average crystallite size increases while electrical resistance decreases with introduction of nitrogen and hydrogen in comparison to oxygen in argon. Nevertheless, the optimum value of optical transmittance and sheet resistance of the films deposited in pure argon are found to be 85-96% in the wavelength range 400-800 nm and 65 {Omega}/{open_square}, respectively.

14 SOLAR ENERGY↗

Analytical Study of BAM (Al/GaAs) and Photovoltaic Samples Using State-of-The-Art Auger Nanoprobes

For the analysis of certified semiconducting Al{sub 0.7}Ga{sub 0.3}As/GaAs superlattices and photovoltaic samples, we used new generations Auger nano-probes such as the JEOL JAMP-9500F Field emission Microprobe and the PHI-700 Xi system. These nano-probes are generally used for the chemical analysis of complex nano-structures at the deca-nanometric scale. In this paper, we first used both systems for the determination of the surface composition of an Al{sub 0.7}Ga{sub 0.3}As/GaAs reference sample. In that, we studied the impact of surface topography on the Auger analysis. Secondly, we used both systems for chemical analysis of photovoltaic samples. Here, we investigated the in-depth chemical composition, in particular the a-Si:H (n)/ZnO/Al and ITO/a-Si:H (p) interfaces, after a specific cross-section preparation. However, limitations such as image drift due to acoustic vibration and heating effects due to continuous bombardment of energetic electrons at the same point are still a big challenge for quick, routine analysis.

36 MATERIALS SCIENCE↗

Some Considerations On Photocurrent Characteristics Of Poly(alkylthiophene) And Photovoltaic Characteristics Of Poly(alkylthiophene)/ZnO Based Hybrid Solar Cells

Photocurrent characteristics of poly(alkylthiophene) has been investigated in ITO/poly(alkylthiophene)/Au structure by performing the V-I measurement at various light illumination intensity. The dependence of photocurrent on light intensity was clearly observed in reverse bias condition. The photocurrent characteristics obey a power law dependence on light intensity, which may be related with the electric field dependent charge carrier generation and transport. Photovoltaic characteristics has been investigated in ITO/Al-doped ZnO/poly(alkylthiophene)/Ag structure. The observed photovoltaic characteristics show the function of this ZnO layer as the acceptor layer. However, the V-I curve indicates unusual behavior indicating Ohmic-like characteristic, which is discussed by considering the nano-morphology and the conductivity properties of the ZnO layer.

36 MATERIALS SCIENCE↗

Germanium subcells for multijunction GaInP/GaInAs/Ge solar cells

Photovoltaic converters based on n-GaInP/n-p-Ge heterostructures grown by the OMVPE under different conditions of formation of the p-n junction are studied. The heterostructures are intended for use as narrow-gap subcells of the GaInP/GaInAs/Ge three-junction solar cells. It is shown that, in Ge p-tn junctions, along with the diffusion mechanism, the tunneling mechanism of the current flow exists; therefore, the two-diode electrical equivalent circuit of the Ge p-n junction is used. The diode parameters are determined for both mechanisms from the analysis of both dark and 'light' current-voltage dependences. It is shown that the elimination of the component of the tunneling current allows one to increase the efficiency of the Ge subcell by {approx}1% with conversion of nonconcentrated solar radiation. The influence of the tunneling current on the efficiency of the Ge-based devices can be in practice reduced to zero at photogenerated current density of {approx}1.5 A/cm{sup 2} due to the use of the concentrated solar radiation.

36 MATERIALS SCIENCE↗

Effects of Mn substitution on the structure and properties of chalcopyrite-type CuInSe{sub 2}

Mn-doped CuInSe{sub 2} compounds (CuIn{sub 1-x}Mn{sub x}Se{sub 2}, x=0.0125-0.20 and Cu{sub 1-y}In{sub 1-y}Mn{sub 2y}Se{sub 2}, 2y=0.0125-0.60) were synthesized by high-temperature solid-state reactions. Single phase materials with chalcopyrite structure persist up to 0.10 and 0.20 doping for CuIn{sub 1-x}Mn{sub x}Se{sub 2} and Cu{sub 1-y}In{sub 1-y}Mn{sub 2y}Se{sub 2}, respectively. The chalcopyrite and sphalerite phases co-exist in the Cu{sub 1-y}In{sub 1-y}Mn{sub 2y}Se{sub 2} system for 2y=0.25-0.50. Attempts to introduce greater manganese content, x=0.15-0.20 for CuIn{sub 1-x}Mn{sub x}Se{sub 2} and 2y=0.60 for Cu{sub 1-y}In{sub 1-y}Mn{sub 2y}Se{sub 2}, result in partial phase segregation. For the single-phase samples, the lattice parameters of both systems increase linearly with manganese concentration and thus follow Vegard's law. The temperature of the chalcopyrite-sphalerite phase transition is decreased by manganese substitution for all single-phase samples. The bandgap of the materials remains around 0.9 eV. Additionally, the Mn-doped CuInSe{sub 2} compounds display paramagnetic behavior, whereas pure CuInSe{sub 2} is diamagnetic at 5-300 K. All the CuIn{sub 1-x}Mn{sub x}Se{sub 2} and Cu{sub 1-y}In{sub 1-y}Mn{sub 2y}Se{sub 2} compounds with chalcopyrite structure show antiferromagnetic coupling and measured effective magnetic moments up to 5.8 mu{sub B}/Mn. - Graphical abstract: The manganese solid solubility can reach up to 10% and 20% for CuIn{sub 1-x}Mn{sub x}Se{sub 2} and Cu{sub 1-y}In{sub 1-y}Mn{sub 2y}Se{sub 2}, respectively, while maintaining phase-pure, chalcopyrite-type materials. Lattice parameters increase linearly with increase manganese concentration suggesting that the manganese ions are distributed randomly on both the indium site and the copper and indium sites simultaneously.

36 MATERIALS SCIENCE↗

Determination of electrical parameters of ITO/CZTS/CdS/Ag and ITO/CdS/CZTS/Ag heterojunction diodes in dark and illumination conditions

In this work, ITO/CZTS/CdS/Ag and ITO/CdS/CZTS/Ag heterojunction diodes has been produced, CdS and CZTS thin film layers of the diode have been produced on ITO glass at room temperature using PLD technique. It has been produced CZTS thin films that have a polycrystalline structure that were annealed at the sulfurization temperatures of 325 °C, 350 °C and 375 °C when as-grown CZTS thin film has the amorphous structure. CdS thin films have been grown on substrate at room temperature in 15, 20 and 25 min that have polycrystalline structures. Then, CdS thin film deposited for 20 min was annealed at 200 °C temperature and, has better crystal structure compared to other thin films. Diodes have been composed of CZTS thin film annealed in 375 °C, CdS thin film was grown during 20 min and, then annealed at 200 °C temperature. According to J–V characteristics of diode, diodes exhibit some rectification behaviour in dark and show a photo-electric property under illumination conditions. In this article, the ideality factors of diodes in dark condition have been calculated, their electrical parameters of J{sub sc}, V{sub oc}, FF and η under the illumination condition have been determined and these electrical properties have been discussed in details.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A method for the assessment of the visual impact caused by the large-scale deployment of renewable-energy facilities

The production of energy from renewable sources requires a significantly larger use of the territory compared with conventional (fossil and nuclear) sources. For large penetrations of renewable technologies, such as wind power, the overall visual impact at the national level can be substantial, and may prompt public reaction. This study develops a methodology for the assessment of the visual impact that can be used to measure and report the level of impact caused by several renewable technologies (wind farms, solar photovoltaic plants or solar thermal ones), both at the local and regional (e.g. national) scales. Applications are shown to several large-scale, hypothetical scenarios of wind and solar-energy penetration in Spain, and also to the vicinity of an actual, single wind farm.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Proton transfer reactions in donor site mutants of ESR, a retinal protein from Exiguobacterium sibiricum

Light-driven proton transport by microbial retinal proteins such as archaeal bacteriorhodopsin involves carboxylic residues as internal proton donors to the catalytic center which is a retinal Schiff base (SB). The proton donor, Asp96 in bacteriorhodopsin, supplies a proton to the transiently deprotonated Schiff base during the photochemical cycle. Subsequent proton uptake resets the protonated state of the donor. Here this two step process became a distinctive signature of retinal based proton pumps. Similar steps are observed also in many natural variants of bacterial proteorhodopsins and xanthorhodopsins where glutamic acid residues serve as a proton donor. Recently, however, an exception to this rule was found. A retinal protein from Exiguobacterium sibiricum, ESR, contains a Lys residue in place of Asp or Glu, which facilitates proton transfer from the bulk to the SB. Lys96 can be functionally replaced with the more common donor residues, Asp or Glu. Proton transfer to the SB in the mutants containing these replacements (K96E and K96D/A47T) is much faster than in the proteins lacking the proton donor (K96A and similar mutants), and in the case of K96D/A47T, comparable with that in the wild type, indicating that carboxylic residues can replace Lys96 as proton donors in ESR. We show here that there are important differences in the functioning of these residues in ESR from the way Asp96 functions in bacteriorhodopsin. Reprotonation of the SB and proton uptake from the bulk occur almost simultaneously during the M to N transition (as in the wild type ESR at neutral pH), whereas in bacteriorhodopsin these two steps are well separated in time and occur during the M to N and N to O transitions, respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗